Search Documents

By Nelson Collao I.

Loss of the organic phase from solvent extraction circuits is a major cost factor for SXEW operations. Recognized sources of loss include evaporation, entrainment, and biological degradation. The mechanisms for both entrainment and evaporative losses are well recognized. Biological degradation of the organic has not been as extensively evaluated as the other mechanisms but is a major source of loss. This paper discusses the impact of biological degradation on an operating plant, potential mechanisms for degradation, conditions under which biodegradation of plant organic can occur and plant conditions that may assist in promoting biodegradation.

Jan 1, 2003

By Sergio Neves Monteiro, Nuã Simonassi, Helvio Pessanha Guimarães Santafé Jr.

"Thermoset polymers, like the polyester, become harder with increasing temperature owing to molecular crosslink formation, which is a thermal benefit for composite matrix applications. Natural lignocellulosic fibers, however, have low thermal resistance and tend to degrade with increasing temperature. Therefore, the combination of a lignocellulosic fiber, as reinforcement, with a thermoset polymer, as the matrix, results in a composite material with complex thermal behavior. In the present work, a thermal analysis was conducted on polyester composites with different amounts of coir fibers. Both TGA and DTG curves were analyzed to determine the effect of the coir fiber on the thermal resistance of the composites. It was found that the coir fiber sensibly affects the thermal behavior of the polyester matrix for fiber amounts above 10% in volume. This effect is associated with an increase in thermal degradation.IntroductionIn recent years, there has been an increase application of natural fibers as reinforcement of polymer matrix composites in several industrial sectors, with special participation in automobile components [1-3]. Figure 1 illustrates the different components of a modem BMW sedan that are fabricated with lignocellulosic reinforced polymer composites."

Jan 1, 2012

By L. Trincado

Mantoverde is a heap leach-SX-EW plant that was commissioned in December 1995 at a production rate of 42,130 ton of copper per year and 5.4 million ton of ore per year. Copper production has steadily been increased to 57,290 ton in 2002. Forecast copper production for 2003 is 60,000 ton for an ore treatment rate of 8.5 million ton. Several improvements in the heap leach process have been implemented. The main process improvements are related to the optimization of heap height, particle size, irrigation rate and leach cycle, in addition to a better heap drainage design and a solution management system. A first dump leach operation was started in 1999 at a production rate of 1,922 ton of copper. A second dump leach operation was started in early 2002 at a production rate of 2,805 ton of copper. Dump leach production will be increased over time to as much as 24,000 ton of copper. The main heap leach process improvements, as compared to the original plant design, as well as the main dump leach operating parameters are discussed in this paper.

Jan 1, 2003

By Kurt Westerlund

The design of the economically most profitable and technically most feasible smelter process gas handing and treatment as an integrated part of the total metallurgical process is discussed and exemplified, with alternative flow sheets including material and energy balances, investment and operating costs. Retrofitting and de-bottlenecking of existing gas handling lines wil1 be described and exemplified. Methods of increasing total gas handling line availability will be described.

Jan 1, 1992

By A. Iván, Patiño C. Francisco, Flores B. Javier, Peréz L. Miguel, Hernandez A. Juan, Trapála P. Norma, Salinas R. Eleazar, Rivera L. Isauro, G. Flores, U. Mizraim

"Tills work is related with the production of tiles using wastes from mining and metallurgical industry of Hidalgo State, as raw material. These wastes present a majority particle size (60 %), minor than 53 m (mesh 270, in Tyler Series) with the following composition; 70.01 % wt. of Si02, 12.82 % wt. of Ah03, 3.80 % wt. of Fe, 0.70 % wt. of Mn, 3.98 % wt. ofK20, 3.34 % wt. of CaO, 2.50 % wt. ofNa20, 0.04 % wt. of Zn, 0.026 % wt. of Pb, 56 grams per ton of Ag and 0.6 grams per ton of Au. In this work, the partial results and experimental conditions for the preparation of some composites to produce tiles are shown. The composite that offers the best results in productions of tiles was that with 66.67 % wt. of mining waste, 26.67 % wt. of red mud and 6.67 % wt. of black mud.IntroductionTo now, mining activities carried out during more than 457 years in Hidalgo State, Mexico; has lead a great volume of wastes; which can be classified into different types, having among the more common; Acid mining water, solid transport water, elements in radical form, abandoned minerals without processing and processing minerals wastes known as burrows, being these the most abundant in the region counting with an approximated volume of 110 million of tons, presenting a fine particle size that can affect population health during windy epochs [1 -4].Form metallurgical point of view, is well known that a fundamental characterization study it is necessary to know the viability of reusing or recycling of these wastes. According this, these residues can also be considered as raw materials in other economical activities, due its Si, Fe, AI, Ca, Na and P oxides contents, its mineralogy and the distribution of chemical elements in the primary and secondary phases [1,2,5,6]."

Jan 1, 2012

By B. Fresz

Before aluminum is utilized in automotive bodies, the longevity of the electrodes employed in the resistance spot welding of aluminum must increase. This paper explores the affects of electrode composition on electrode life. To compare these variables, electrode tests were completed on a Taylor Wield welding machine using, Cu-Cr, Cu- Zr, Cu-Cr-Zr, Cu-Be, and Glidcop electrodes tested to 12.5%, 25%, 50%, 100%, and 150% lifetimes. Electrode diameters were found via a magnification technique using a PULNIM video camera attached to a low magnification Wild Heerbrugg stereo-zoom microscope. From these measurements, graphs of electrode life verses face diameter and weld number verses face diameter were created. Analyses of these graphs suggest that a single failure mechanism is responsible for electrode failure, though the number of welds until failure (100% electrode life) varied with composition (700-2000 welds).

Jan 1, 1999

By Manuel Pérez-Tello

A mathematical model to represent the expansion and fragmentation of copper matte particles oxidized under flash converting conditions is presented. The model assumes the particles to be initially nonporous, have a constant mass prior to fragmentation, and travel at a constant velocity throughout the reaction chamber. The model requires the specification of five parameters: the particle expansion rate, a fragmentation diameter factor, a fragmentation size distribution parameter, and the fractions of the finest and the coarsest particles in the feed that undergo fragmentation. The model predictions show good agreement with experimental data collected in a laboratory flash converting furnace over a wide range of experimental conditions. The evolution of the size distribution of the particles along the reactor length was computed, and the model parameters were correlated with the experimental operating variables. Model predictions indicate that particle residence time is an important factor in the generation of dust. The presence of two maxima in the particle density function may be attributed to turbulent conditions prevailing in the furnace, which cause particles to follow very different trajectories within the furnace even if they are injected at the same location.

Jan 1, 2006

By M. I. Zinigrad

A model of an ideal associated solution is presented. This model takes into account the existence of complexes of various compositions, sizes and geometries and allows calculating thermodynamic properties and phase diagrams of binary alloys. The model has been used formerly to calculate thermodynamic parameters and the position of the liquidus line for binary eutectic systems and also those having a stable compound in the solid phase. In all the cases the model parameters were not adjusted rather estimated from melting temperatures of the components. The recent studies dealt with the influence of arbitrary-stoichiometry associates on the equilibrium thermodynamic properties of liquid alloys. The application of the model to eutectic systems and systems having an unlimited solubility in solid and liquid states close to liquidus has been considered. It was shown that if the difference in melting temperatures of the components was small, different types of fusibility diagrams were possible: eutectic diagrams, cigar-shaped diagrams or diagrams with upper or lower azeotropic points. Peritectic transformations could take place when the difference in melting temperatures of the components was large. The present work is devoted to calculation of phase diagrams and thermodynamic properties of binary systems on the basis of chrome.

Jan 1, 2006

By Jinxing Ji

The thiosulfate lixiviant system for leaching of gold has been under extensive investigation for nearly two decades and consists of ammonium thiosulfate, copper and ammonia. There are several challenges with this system. The occurrence of ammonia must be taken into account from a health and hygiene aspect in the workplace, and also from an environmental perspective with significant levels of ammonia and copper in the tailings. Copper accelerates the leaching rate but causes excessive thiosulfate degradation. A new lixiviant system that has been investigated consists only of sodium thiosulfate without copper and ammonia. Gold leaching is carried out in an enclosed reactor with slightly elevated oxygen overpressure and temperature. Extensive leaching experiments were carried out to minimize thiosulfate degradation and polythionate formation while maximizing the gold extraction. For the preg-robbing carbonaceous ore sample tested, gold leaching was essentially complete within six hours and the thiosulfate consumption was lower than in the typical ammoniacal thiosulfate system. The gold thiosulfate complex in the pregnant leach solution was found to be quite stable under ambient conditions. This new leaching system has the advantages of being more environmentally friendly, has a shorter residence time, lower thiosulfate consumption, lower oxygen consumption, and is easier to control.

Jan 1, 2003

By Tae-Hyun Kim, Shun Myung Shin, Jin-gu Kang, Jeong-Soo Sohn

We investigated about synthesis of Mn-Zn ferrite with spinel structure using sulfuric acid leaching solution of mixed spent zinc-carbon batteries and spent alkaline batteries. The waste batteries were prepared by physical treatment such as crushing, magnetic separation, and screening. After screening, the crushed batteries were separated to +8 mesh and -8 mesh powder. Among these, under 8 mesh powder was selected for leaching test. The leaching test was investigated at 2 M H2SO4, 4 vol.% H2O2, reaction temperature 60 ?, agitation speed 250 rpm, solid/liquid ratio 50 g/ 500 ml, reaction time 1 h. The leaching efficiency of zinc, manganese and iron were 99.0%, 98.9%, 58.5%, respectively. For co-precipitation of zinc, manganese and iron, 5M NaOH solution was used for pH control. Then in order to synthesize Mn-Zn ferrite powder, it was investigated according to reaction temperature, agitation speed and O2 partial pressure. We could synthesize about 20 nm of Mn-Zn ferrite with spinel structure.

Jan 1, 2008

By Kenneth E. Smith

"Cold weather heap leaching can be grouped into two basic regions: Arctic and near Arctic, with various operational techniques or combinations of operating techniques dictated by latitude and site topography.The basic cold weather regions are Arctic areas, those areas above the Arctic circle (60° North latitude) and near-Arctic areas, (between 50° and 60° North latitude).As techniques and operational philosophy have advanced, heap leaching operations have moved into progressively colder regions.ABSTRACT ONLY"

Jan 1, 1997

By Susan A. Fredholm, Randolph E. Kirchain, Elsa A. Olivetti, Jeremy R. Gregory, Jeffrey B. Dahmus

"A general model for evaluating the economic and environmental performance of electronics recycling systems is developed. This model comprehends the three main functions in a recycling system – collection, processing, and system management – and aims to enable quantification of the impact of context and system architecture on the economic and environmental performance of electronics recycling systems. Such a model can be used both to evaluate and improve existing electronics recycling systems, as well as to design and implement new systems. A case study, based loosely on Maine, is presented to show the utility of such a model.IntroductionAs recycling systems for complex durable goods (CDGs), and in particular for waste electronics, become more widespread, understanding the economic and environmental performance of such systems becomes critical, both to enable improvement of existing systems and to inform the design of new systems. However, with the range of possible system architectures and the important role of locational characteristics (context), understanding the determinants of system performance is challenging [1]. To address this issue, a modeling framework to project the economic and environmental performance of CDG recycling systems, based on contextual and architectural characteristics, has been developed.The modeling framework presented here comprehends the three main functions – collection, processing, and system management – which are common to most recycling systems. These three functions are modeled using a variety of modeling techniques and serve as a bridge between inputs related to system context and system architecture, and outputs related to economic and environmental performance. The models developed here are intentionally meant to be both broad, in order to address entire recycling systems, and general, such that many different systems, both real and hypothetical, can be analyzed."

Jan 1, 2008

By James Vaughan

Ionic liquids are solvents of interest for applications such as electro- plating, winning and refining of metals. Of particular interest is the possibility of processing reactive metals such as aluminium, magnesium and titanium that cannot be deposited from aqueous solutions. Aluminium has been electro deposited from AlCl3 : ionic liquid mixtures at low temperatures relative to conventional Hall-Héroult smelting. Imidazolium ionic liquids are have been used in the past due to their relatively high ionic conductivity and cation stability. The less studied and less expensive phosphonium ionic liquids systems may provide a viable alternative to imidazolium ionic liquids for certain applications. New information regarding the physical properties and electrochemical behaviour of phosphonium ionic liquid systems is presented.

Jan 1, 2006

By Barry T. Kilbourn

A dominant characteristic of many derivatives of the lanthanides is stability at high- temperatures. Combine this with novel solid-state behavior under those conditions and there is the potential for new materials that can not only improve existing applications but also help create new technologies. These property themes will be traced through new uses ranging from efficient energy generation and raw material conversion to control of environmental emissions and temperature measurement. Conducting ceramics, methane conversion catalysts, sulfur oxide capture agents and phosphor hosts will be described. Some categories will account in the future for significant lanthanide consumption whereas others will remain commercially negligible but technologically vital. All uses will illustrate the versatility of those elements inappropriately termed rare.

Jan 1, 1992

By David Ellis

The next generation of Reusable Launch Vehicle (RLV) will utilize regeneratively cooled combustion chamber liners in the engines. The current design calls for using a new Cu-8 at. % Cr-4 at. % Nb (Cu-8 Cr-4 Nb) alloy for the liners. Work is ongoing to characterize the thermophysical and mechanical properties of the alloy from - 253 to 800°C, the temperature range to which the alloy will be subjected during service. The alloy has been commercially produced in quantity for NASA. The powder size has been characterized and the microstructure examined. The powder was extruded into bar using a commercial extrusion press. In addition, samples have been hot isostatically pressed (HIPed) at NASA Glenn Research Center. Both processing methods produced fully consolidated material. Transmission electron microscopy (TEM) revealed highly faulted Cr2Nb and some elemental precipitates. Cryogenic tensile testing showed the extruded specimens had significantly higher strengths than NARloy-Z (Cu-3 wt % Ag-0.5 wt % Zr) even after being subjected to a simulated braze cycle. The Young's moduli (Cu-8 Cr-4 Nb) were lower than NARloy-Z. The lower moduli is highly beneficial for reducing thermally induced stresses in rocket engine combustion chamber liners and similar applications.

Jan 1, 1999

By Bora Derin

Optimization of slag composition has great importance on effective and clean metal production technologies. Reddy-Blander (RB) model, a priori, is very useful tool for prediction of impurity capacities of industrial slags. In this study, sulfide capacities (Cs) of 19 lead smelter slags indicated in the literature were calculated and effects of Cs values on sulfur content of lead bullions were discussed.

Jan 1, 2006

By Roberto Javier Santiago

The main properties of Calcium Carbide seem to be the grain size and the CaC2 content. This paper tries to describe the Calcium Carbide used in the South-American steel plants and how and where it is added.

Jan 1, 2006

By Shigeo Asai

History of EPM is described and several functions utilized in EPM are reviewed. Main activities of EPM are summarized with the view on mass production and applications of high magnetic field related to nano-technology. Future trends and prospects of EPM are discussed.

Jan 1, 2006

By J. E. Dutrizac

The behaviour of the lanthanide elements during the precipitation of sodium and potassium jarosites at 98oC from sulphate media was systematically investigated. The lower atomic weight lanthanide elements (La to Gd) are characterized by the limited solubility of their alkali-lanthanide sulphates, such as NaNd(SO4)2?H2O, which commonly contaminate the jarosite precipitates. Hence, single phase jarosite-type compounds were precipitated only from solutions containing <0.4 g/L of the La to Sm lanthanides. The sulphates of the heavier atomic weight lanthanide elements (Tb to Lu) have significantly higher solubilities such that solutions containing up to 10 g/L of the individual lanthanides could be investigated without the precipitation of alkali-lanthanide sulphate species. Even at the highest lanthanide concentrations, however, none of the jarosite precipitates incorporated more than 0.3 wt% of any of the lanthanide elements. Comparable levels of lanthanide incorporation were noted in both Na-jarosite and K-jarosite. Although the mass of the jarosite precipitate increased with increasing ferric sulphate concentration or with increasing pH, the extent of lanthanide incorporation was not significantly affected. Clearly, the trivalent lanthanide elements do not substitute extensively for trivalent iron in the jarosite structure. This behaviour likely reflects the significantly lower hydrolyzability and larger size of the trivalent lanthanide ions relative to ferric ions.

Jan 1, 2003

By Y. F. Jia

Arsenic constitutes a major contaminant for the hydrometallurgical industry. Its removal and immobilization from process effluents typically involves lime neutralization and co-precipitation with ferric iron (Fe (III)/As(V)>3). Alternatively, precipitation of scorodite (FeAsO4?2H2O (cr)) may be applied to arsenic fixation. The mechanism of arsenic fixation in the former process has been suggested to be surface adsorption. Unequivocal characterization of these products is difficult because of their amorphous nature hence a variety of methods need to be applied including the particularly powerful method, extended x-ray absorption fine structure (EXAFS) spectroscopy. In this study, we have investigated the preparation of arsenate-adsorbed ferrihydrite with the purpose to compare its structure to that of Fe(III)-As(V) co-precipitates and scorodite (both amorphous and crystalline). Furthermore the solubilities of these Fe(III)-As(V) solids are measured as a function of pH. Their structures are elucidated and correlated to their solubilities and thereby the application of these findings to the practice of arsenic removal and disposal is assessed.

Jan 1, 2003