Search Documents

By Jose Carlos D’Abreu, Edelink Efrain Tinoco Falero, Mauricio Marcos Otaviano, Helio Marques Kohler

Nowadays the most important Direct Reduction - DR processes in shaft furnaces has to deal with carbon fines precipitation and DRI carburization issues. Based in a cooperative research program joining Catholic University (PUC-Rio) and SAMARCO Mining Co, a project dealing with pellets reduction and those two phenomena was established. This work analyzes kinetically the three reactions mentioned before, considering typical values for the operational variables temperature, flowrate, pressure and gas composition, parameters commonly used to control the DRI formation in the Reduction Zone - RZ of the shaft furnaces. From laboratories experimental results, the kinetic equations for those reactions were established and, using the superposition principle, generated a specific global kinetic model for the iron oxide reduction and the soot formation. Finally, using those experimental results and applying a planned statistical factorial analysis for the experiments, the numerical coefficients for each equation were calculated and the correlation factor determined for the proposed global kinetic equation.

Jan 1, 2015

By HeeDong Lee, Owen Reedy, Lawrence Matson, Naidu Seetala, Thomas Key

Spark Plasma Sintering (SPS) consolidated ZrB2+SiC composites using nano-powders (around 40 nm) showed smaller grains compared to those using micron size powders and segregation of SiC into islands is minimal but with higher oxidation of ZrB2 to form ZrO2 in nano-composites. Argon-gas purging prior to SPS consolidation at around 2000 °C and 40 MPa of ZrB2+20vol.%SiC nano-powders was used to minimize the oxidation and obtain fine granules with high densification. The densification of the Argon-gas purged nano-composites is higher compared to those consolidated without Argon gas purging. The EDX analysis showed a strong reduction in the oxygen peak for the Argon gas purged composites. The XRD spectra also support this observation with less ZrO2 phase composition in Argon gas purged composites. The Vickers micro-hardness showed slightly lower values for Argon gas purged composites though they have higher densification.

Mar 1, 2017

By Michael J. Mankosa

The increased emphasis placed on recycling of consumer and industrial waste products has generated a need for advanced separation techniques for recovery of valuable by-products. As a result, the metals recycling industry has made great strides in the recovery of used wire products through the application of chopping and screening processes. Unfortunately, in many instances, the final plastic reject still contains a substantial portion of valuable metal. Typically, this material has been discarded, since an appropriate separation technique has not been available. Recent work conducted by Carpco, Inc. in Jacksonville, Florida indicates that a high-grade metal and/or plastic product can be recovered from this waste material using a novel density separation process. Extensive test work has been conducted using this procedure to validate separation performance as well as equipment capacity. This paper will present the basic operating principle of the separator, as well as results from tests conducted using various feed materials.

Jan 1, 1995

By Patrick R. Taylor

A novel method for Chemical Vapor Infiltration (CVI) using plasma technology is proposed, Plasma Enhanced CVI (PE-CVI). Due to the low rates at which CVI is currently performed, the use of plasma as a source of heat may be considered to be a faster and less expensive production method. Precursors fed in the hot region of the plasma gas are completely vaporized and forced by the same flow through a porous preform where it condenses as a new material. In this research, silica and methane where used as precursors to form SiC/on a / graphite felt (preform). To enhance the infiltration process, vacuum was used to increase the flow through the preform. Characterization of infiltrated graphite was perfontied using Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD). A uniform distribution of Sic was observed along the felt with only twenty minutes of infiltration process, yielding a 178% increment in weight.

Jan 1, 1997

By G. C. Yao

Branch and needle-shaped intermctallic compounds of iron, silicon and aluminum normally exist in the molten aluminum. If a suitable amount of manganese metal is added into molten aluminum, the shape of the intermallie compound particlcs may become lumpish and spherical. According to the difference in electric and magnetic properties of these impurity particles and molten aluminum, these impurity intermctallie compound particles can be separated by applying an alternating magnetic field. In this experiment the alternating magnetic field was formed by a "C" type loop with AC (50Hz) current. The inner vacuum of the fireclay refractory separator is 25>< 15" 130mm3 with a lateral baffle inside. The separator was put into the interspace of the "C" type loop. It was found that the longer the separation time, the larger the amount transferred of impurities. The amount of transferred impurities increases with the increase of separation time and intensity of magnetic field. The addition of manganese metal enhanees signifieantly the efficiency of impurity separation.

Jan 1, 2003

By J. -S. Park, H. -S. Jeon

This study has been carried out to develop a relatively simple hydrometallurgical process for recovering nickel as nickel sulfate from the spent nickel-cadmium battery residue in which cadmium was removed by vacuum distillation. This residue is composed of 36 % nickel, 20 % iron, and other metals such as cobalt. First, crushing and selective classification were performed to separate iron to produce a nickel-rich product (over 40 % nickel). This product was dissolved in sulfuric acid to obtain a nickel sulfate solution. During the dissolution, nitric acid and air were added to the system to enhance the iron oxidation reaction rate. The free acid remaining in the dissolved solution was neutralized by adding nickel carbonate. Iron was precipitated as iron hydroxide and removed from the solution. The nickel sulfate solution was then fed to a vacuum evaporator to concentrate the solution by evaporation of water and crystallized at around 45°C to obtain nickel sulfate hexahydrate. A recrystallization process could remove other impurities such as zinc and manganese.

Jan 1, 2000

By José Roberto de Oliveira

Based on literature review one can see that the main objectives of MnO reduction is the comprehension of slag interactions and reactions with other elements beyond carbon. That&apos;s because it is worthwhile to study pure MnO reduction, where there will be not oxides interaction and just carbon will be the reduction agent. By a thermodynamic analysis we know that Si can react with MnO, then it&apos;s important to study this influence, so as Mn content. Our work aims to develop kinetics parameters for the MnO reduction, varying Mn and Si contents in bath. This has been given by pressure measure of CO in a Fe-C bath. The CO is generated by the oxide reduction with carbon. It has been proved that: - Mn content decreases the MnO reduction; - the MnO reduction is mainly influenced by Si content in a bath containing Iron, Carbon and Manganese so as Silicium

Jan 1, 1997

By Hiroki Kumakura, Kotaro Seki, Takashi Nagai, Masahito Abe, Daiki Noguchi

A large amount of platinum group metals (PGM) are used in automobile catalyst. It is important to recover the metals from wasted catalyst. PGM in the catalyst are supported by ceramics for four-wheel vehicle or metals such as stainless steel for two-wheel ones. The recycling process of PGM from the metal-supported catalyst has not been developed, while the process for ceramic-supported catalyst was developed, such as Rose process. We designed a noble recycling process of PGM from metal-supported catalyst using complex oxides between PbO and PGM oxide. In this study, complex oxides, PbPt2O4, PbPdO2, PbRh2O4 and so on were synthesized at about 773–973 K. And the dissolution behavior of these compounds to hydrochloric acid was investigated. PbPt2O4 and PbPdO2 were dissolved to hydrochloric acid easily, but PbRh2O4 was not.

Mar 1, 2017

By Zhang Libo, Li Wei, Peng Jinhui, Guo Shenghui, L. Jing

Partially stabilized zirconia ceramics (PSZ) were prepared by microwave sintering using natural baddeleyite which was obtained by flotation of baddeleyite ore as starting materials. Because of using natural baddeleyite as raw and the process producing no waste, it realized shorter process, energy savmg, environmentally-friendly and non-damage processing. In this work natural baddeleyite stabilized with 3.8wt.% CaO were sintered at 1300°C for 60min in a multi-mode 2.45GHz microwave furnace. Microwave sintering could fast heating and sintering. Besides that, microwave sintering could heat materials wholly, low the sintering temperature, improve the materials properties and save energy. X-ray spectrum displayed the product composed by the tetragonal phase and monoclinic phase that also showed the product was PSZ. Fine and uniform microstructures were observed in the product through scanning electron microscopy. PSZ which was with high density was confirmed by the method of the Archimedes technique.

Jan 1, 2011

By D. M. Fermino, C. G. Bastos Andrade, M. G. Fernandes, F. R. Valenzuela-Diaz

Treatments with high concentration solution of inorganic acid at temperatures under boiling point are a usual method for clay minerals structure modification. For many industrial uses bentonites must be cleared of impurities. In the present paper, a sample of Brazilian bentonite from Vitoria da Conquista, Bahia was modified by mild acid attack using hydrochloric acid under moderate conditions (90 °C, reaction times of 1, 6, 12, 18 and 24 h in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5 M, acid solution/clay ratio of 1 g/10 mL). The attacked samples were characterized by CEC, XRF, SEM, EDS and Stereomicroscopy. The purpose of these attacks is to reduce the concentration of impurities with minimal damage in clay minerals structure. The modified bentonite presented good results and tends to be a good economic and environmental alternative to manufacturing products with high added value such as polymer/clay nanocomposites, cosmetics and medicines.

Mar 1, 2017

By Andreas Dietrich

Laser off-gas measurement of CO, O2 and temperature has been carried online in EAFs. A visualization screen shows the values of CO and Oxygen and temperature for the entire heat, and includes the status of furnace equipment. The historical data of the heats are stored such that the furnace performance can be evaluated and optimized. A short comparison between laser based and conventional systems has been carried out related to speed, influence of dust, water, pressure, protection for bag house explosions. A high water and/or dust content in the sample does not represent a problem for this type of system. The measurement method works without interruption even under worst conditions such as dirty scrap, carbon injection etc. The installation was developed in conjunction with Marienhuette, Graz. They are 100% scrap based with a tap to tap time of ca. 46 min. Keywords: Laser Measurement, Off Gas, CO, O2, Temperature

Jan 1, 2003

By Barry J. Welch

The production of primary aluminium can potentially lead to metal that, with minimum treatment, meets a high purity standard. Smelters that can achieve a significant proportion of their production in this manner have a competitive edge which is of growing importance as the use grows for such items as compact discs and the like. Superimposed on the desire to produce high quality metal are stringent environmental requirements that the industry must adhere to. The environmental &apos;legislation focuses on fluoride emissions and the approach adopted is towards a zero waste management philosophy. The fluoride recycling process does, however, result in volatile impurities being captured and recycled to the cell. Aluminium has an extremely high reduction potential and this results in a significant proportion of the recycled impurities being reduced at the electrolyte metal interface and thus contaminating the metal. This paper reviews sources of impurities and the impact of the operating procedures adopted on metal treatment.

Jan 1, 1996

By D. M. Fermino, C. G. Bastos Andrade, V. F. Justo, F. R. Valenzuela-Diaz, M. G. S. Valenzuela, C. Volzone

The present paper presents the study of light green smectite clay, from Paraiba, Brazil, submitted to mild acid attack under moderated conditions. Usually, clays are subjected to treatment with strong inorganic acids at temperatures near the boiling point and at high acid concentrations and then, widely used as bleaching agents. The treatment occurred under bellow boiling temperature and at short times of reaction (90°C, reaction times of 1, 6, 12, 18 and 24 hours in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5 M, clay/acid solution ratio of 1g/10mL). The purpose of these attacks is to reduce the concentration of impurities providing color, with minimal change in the clay minerals structure, aiming at use in products of high value such as cosmetics and polymer/clay nanocomposites. The raw clay and the attacked samples were characterized by X-ray diffraction (XRD), cation exchange capacity (CEC), stereomicroscopy, scanning electron microscopy (SEM) and energy dispersive X-ray detector (EDS).

Jan 1, 2015

By Jongmin Jeong, Jaehong Shin, Joo Hyun Park, Chul-Woo Nam, Kyung-Ho Park

Because sulfur and phosphorus are very harmful in steel products, there are increasing requirements for refining these elements from ferroalloys industries. Hence, in the present study, simultaneous desulfurization (de-S) and reducing dephosphorization (Rde-P) from silicomanganese (SiMn) alloy were investigated using metal-slag equilibration method under highly reducing condition at 1773 K. Experiments were carried out by equilibration between SiMn alloy and MnO-based slag in graphite crucible under p(O2) = 10−18 atm. Slag composition was designed by changing basicity (CaO/SiO2) and MnO content at fixed Al2O3 (=20%) and MgO (=5%) contents. De-S ratio increased with increasing basicity until C/S = 1.5 whereas Rde-P ratio was not significantly affected by slag basicity. This was because thermodynamic driving force of de-S reaction was greater than that of Rde-P reaction under present experimental conditions. The de-S and Rde-P ratios commonly increased with decreasing oxygen partial pressure.

Mar 1, 2017

By Ditze A., C. Scharf

Magnesium type 1 - scrap can be remelted without flux in the presence of different sulfur containing protective gases. Beside the draw back in the use of these gases, that either are contributing to the global warming potential (SF6) or are poisonous (S02), residues like dross and crucible sludge are produced. Dross and sludge now a days must be utilized. Partly these byproducts can be used in the aluminum industry and partly for desulphurisation of hot metal and steel. Another possibility is melting of dross and sludge with flux for the production of a secondary magnesium alloy. Then again residues are generated that must be processed. Therefore, the whole material cycle has to be considered to decide which kind of utilization practice is optimum. Based on experiments this question is discussed and the material balances for fluxfree melting, melting with flux and fluxfree melting plus other utilization of the residues are presented.

Jan 1, 2000

By Mituo Tougo, Mitsuo Tokunoh, Takayasu Kisaragi, Fuminori Chiba

We have about 200,000 tons/year of dross residue produced after the collection of aluminum from the dross generated during the aluminum remelting process. 130,000 tons of the dross residue is used as a steel deoxidant or a cement material, and the remaining 70,000 tons is abolished and buried in the ground at authorized places. The dross residue is increasing along with the increase in the aluminum production. This situation will grow more serious with a large amount of aluminum window sashes which have been mass-produced since 60's and will return before long as scraps. Our effort is being directed to the development of technologies which enable the dross residue to be recycled and reused for some purposes such as road aggregates, refractories and others, in such a way as to comply with the social requirement which gives prfority to the recycling industry, as well as to the environmental preservation.

Jan 1, 2000

By V. Bredykhin

The efficiency of scrap processing depends firstly on reliability of information about its chemical composition. The paper presents the results of the investigation and development regarding solid copper alloy scrap in the range of lump size 40÷300 mm. Nowadays the sorting of lump scrap is done by two methods: 1. Sorting according to metals and alloys is done at places of scrap generation, and further till metallurgical processing each lot has its "certificate"; 2. Hand sorting of scrap is done according to the marks on solid items in special shops using proximate analyzers or manually by experienced workers. This sorting process is labor - consuming low efficient and involves mistakes. The informational method is a promising trend in the copper scrap sorting. The method is direct, i.e. as a result of sorting the chemical composition of each scrap lump or main elements is determined, and assured data of qualitative and quantitative composition are received.

Jan 1, 2006

By Rodney L. LeRoy, Michel G. Drouet, Peter G. Tsantrizos

"DROSRITE is a unique process that makes possible economic in-plant recovery of metal from hot aluminum dross. It is environmentally friendly, requiring no salt and producing no C02 or NOx gases. The salt-free residues of the process are suitable for production of calcium aluminate or for other value-added use. The process is highly energy efficient, extracting process heat from energy in the residue and, thus, it does not require an external plasma torch, electric arc or fuel heat source.A DROSRITE pilot unit built by PyroGenesis has been tested with both black and white dross types. The unit was installed at two different aluminum plant locations, and tests were conducted for a total of six weeks ""online"" with hot metal holding furnaces where the dross was skimmed.Results of both of these industrial trials are presented, together with an economic analysis indicating cost savings in excess of $1 70 per ton of dross treated."

Jan 1, 2000

By John M. Rapkoch

In the continuing search for copper matte converting methods, commercially available and feasible choices remain Peirce-Smith Converters, Hoboken Converters, Mitsubishi Converting, Ausmelt converting, and Outokumpu/Kennecott Solid Matte Oxygen Converting (?Flash Converting?). While each alternative improves on Peirce-Smith Converters? limited fugitive gas capturing capability, the Peirce-Smith Converter is relatively easy and economic to operate and has an unmatched ability to accept valuable but difficult-to-handle material such as scrap anodes and purchased scrap copper. Recent experience with designing, building, and starting up an ISASMELT facility, applied in primary smelting of copper concentrates, has led the authors to speculate on how suitable the ISASMELT process would be for copper converting, given its low fugitive gas release and its ability to accept a variety of feed types. This paper reviews the potential metallurgical challenges posed by converting copper matte in an ISASMELT vessel and considers possible engineering and design challenges posed by the inclusion of this technology into a new or refurbished copper smelter.

Jan 1, 2006

By S. Subhawong

Following the startup of the zinc plant in Clarksville, Tennessee, in 1978, the original effluent treatment plant did not perform as designed. The sludge, produced in a conventional lime neutralization treatment, settled poorly and began to fill the permitted lined impoundment within two years, well short of the original design capacity. Another sludge pond had to be constructed. This led to a new process modification of the original design. Although the design is still based on the conventional lime precipitation of heavy metals, the current effluent treatment plant has evolved into a hydrometallurgical circuit, capable of producing good quality water without generating sludge. Undesirable elements are bled from the zinc circuit and are rejected through the effluent treatment operations. Wallboard grade gypsum is produced, instead of sludge, and all the gypsum is sold to cement and wallboard plants. This operation also recovers and returns more than 1,500 tonnes of zinc annually to the 105,000 tonne/y zinc plant.

Jan 1, 2000