Search Documents

By Sebastian Schmuck, Petrico von Schweinichen, Dieter Senk, Mohammad Peymandar

"At Department of Ferrous Metallurgy of the RWTH Aachen University in Germany steels in the system Fe-Mn-C(-Al) are investigated and produced in the framework of the SFB 761 ""steel-ab initio"". A new world of steel grades leads to special challenges regarding the production and recycling at the end-of-life cycle of product. In order to recycle high manganese steel alloys the EAF has to be chosen preferentially. A good slag practice is necessary avoiding loss of manganese content during melting in the EAF. This paper investigates on the reaction kinetics at the interface of slag and steel containing Mn (17-22 wt.-%) and up to 3 wt.-% Al. The effect of changes in the composition of slag and steel on the interfacial reaction kinetics is studied. The thermodynamic software FactSage™ is utilized to calculate the composition of slag and steel at equilibrium.IntroductionTRIP and TWIP steels are highly alloyed steels which show superior strength and ductility when compared to standard carbon steel and stainless steel alloys. These TRIP- and TWIPsteel grades contain typically 15-30 wt.-% manganese, 0-4 wt.-% silicon and aluminum, and up to 1 wt.-% carbon. Steels containing 18-28 wt.-% manganese and 0.7-1.2 wt.-% carbon together with aluminum addition from 3 to 12 wt. -% and without silicon refer to TRIPLEX high manganese steel alloys. These alloys combine high strength at even large ductility [ 1-4]. At the Department of Ferrous Metallurgy (IEHK) of the RWTH Aachen University in Germany, steels in the system Fe-Mn-C(-Al) is under investigation at the collaborative research center, SFB 761 ""Steel-ab initio"". In this project, high manganese alloyed TRIP and TWIP steels are in the focus.The mechanical properties such as high strength and high ductility make this kind of steels perfect candidates for impact absorption applications in auto body such as vehicle doors and bumpers [2, 5]. With increasing the use of TRIP-, TWIP- and TRIPLEX-steels more high manganese steel scraps will be available at the end of life cycle of products, which need to develop the technologies and metallurgical processes to recovery of high manganese steel. A new steel grade brings new challenges in recycling. In order to recycle high manganese steel scraps the electric arc furnaces (EAF) have to be chosen preferentially [1]. Nevertheless it's not easy to prevent the manganese loss during the process in EAF. During the oxygen refining of high manganese molten steel in EAF the manganese content decreases strongly by oxidation and vaporization, which is affected by slag composition, slag properties such as basicity and viscosity, slag weight as well as melt temperature [6-8]."

Jan 1, 2014

By Zhi-biao Yin

Copper smelter flue dusts often cannot be directly recycled to the smelting process and accumulate as hazardous wastes requiring environmentally acceptable disposal. Because of the limited amount of flue dust, a separate copper extraction process must be simple and require-a small plant investment. A flue dust process has been developed, consisting of the following steps: (1) roasting a pelletized mixture of hydrated lime and flue dust to fix arsenic and sulfur as insoluble calcium salts, (2) heap leaching the roasted pellets with a buffered ammonia/ammonium salt solution to extract copper as an ammine complex in a lined cell that is the final repository of the leached pellets, and (3) boiling ammonia from the lixiviant to precipitate copper. Condensed ammonia and the filtered solution are returned to leaching. Heap leaching in the final repository cell lowers the capital investment significantly compared with competing extraction processes. Chemistry with respect to arsenic, sulfur and copper is discussed.

Jan 1, 1992

By Hye-Sung Kim, Dong-Wha Kum, Gyeungho Kim

"Mechanical alloying is an effective way to finely distribute inert dispersoids in AI-TM (TM is a transition metal element) systems. It is considered that high melting point aluminides are formed by precipitation from the supersaturated aluminum matrix. The analysis is based on the fact that much higher content of TM than the solubility limit can be dissolved in alpha aluminum during the high energy ball milling. Nonetheless, the role of undissolved TM particles affecting the formation of aluminides is not suitably considered. In this paper, authors present experimental observation on the formation of Ab3Ti particles from mechanically alloyed AI-Ti alloys in the hyper-peritectic region. This study showed that, in the mechanically alloyed AI-20wt%Ti specimen, intermediate phase of cubic Ab3Ti and tetragonal AIz4Tis formed at 300 - 400°C and 400 - 500°C, respectively, before the MA-state reaches to the global equilibrium at higher temperatures. The formation behavior of Lh- Ab3Ti is interpreted by interdiffusion of Al and Ti in solid state based on the fact that large amount of nano-sized Ti particles exist in the milled powder. Present analysis indicated undissolved Ti particles of nanosize should have played an important role initiating the formation of Ab3Ti phase during annealing.IntroductionInterest in the hyper-peritectic AI-Ti alloys is based on industrial demand for high-modulus and high-temperature aluminum alloys. Earlier works on hyper-peritectic AI-Ti alloys with 4 to 12wt%Ti show that these alloys are strong at ambient temperature and maintain high strength above 300°C when titanium-trialuminide (e.g., Ab3Ti) is finely distributed in the aluminum matrix [1,2]. High melting point and high stiffness with low density of AbTi make the AI-Ti alloys strong with greater thermal stability while keeping weight savings as much as possible. Titanium in aluminum shares other merits of transition metal additions because Ti solubility in Al is low (i.e., 1.l5wt%Ti at 665°C and virtually zero below 400°C), and fine dispersion of Ab3Ti particles is readily accomplished and resists grain coarsening effectively."

Jan 1, 1996

By Aichun Dou

Au-Sb alloy sample in which the total amount of Cu and Ni is below 25% (wt. %). In practice, Cu and Ni were difficult to be dissolved in sulphuric acid solution by oxidative leaching under the atmospheric pressure conditions, because of the lower concentration of Cu and Ni in the sample. In this paper, pressure oxidation leaching in sulphuric acid system (POLS) followed by hydrochloric acid leaching (HAL) was employed to remove impurities in the Au-Sb alloy. The effects of variables in POLS on leaching ratios of different metals were investigated in detail. Under the optimal conditions: the concentration of H2SO4 is 1.5 mol/L, liquid-solid ratio is 7:1, the amount of oxidizer is 1.2 times of the theoretical amount, leaching time is 4h and leaching temperature is 427K, the leaching ratios of copper and nickel reached up to 99%, antimony, lead and silver were not dissolved in dilute sulphuric acid solution. The residue from POLS was then treated with hydrochloric acid solution in fixed conditions, the leaching ratio of antimony reached over 92%, the grade of gold in the ultima residue was enriched up to 66%.

Jan 1, 2016

By Nobumasa Kemori

Six kinds of copper '90ncentrates. were treated individually in a ,pilot scale. Outokumpu flsah smelting furnace ~n order to study their ?flash smelting behavior with respect to oxygen efficiency and dust generation. The copper concentrates tested were selected from the more than twenty sources which are treated at the Sumitomo Toyo copper smelter, so as to provide a wide range of chemical composition in terms .of Cu, S,Fe, Pb + Zn + As, and Si~ content. Oxygen efficiency 'and dust generation rates obtained in 'the experiments ranged from 80% ,to 108% and 11% to 20%, respectively. Relationships between these results and experhnental conditions such as chemical and mineral composition of the copper concentrates, flux ratio, fuel consumption and so on are also discussed quantitatively in this paper.

Jan 1, 1998

By Ximeng Zhu

The electrochemical behavior of mineral and coal pyrites in stirred and quiescent alkaline boratelsulfate solutions @H 7.9-10.5) have been investigated using cyclic voltammetry. Significant differences in the electrochemical response of these pyrites were observed. At the mineral pyrite surface, three anodic peaks at about -0.8 V, -0.1 V and +0.5 V (SCE) have been detected along with their corresponding reduction peaks. The first two peaks correspond to FeIFeOI) and FeOI)lFe(III) oxidation. The third peak is present for quiescent conditions but disappears as a distinct peak when the electrolyte is stirred. In the upper voltage region +0.30V (SCE), the current increases markedly during stirring and the reactions correspond to the oxidation of pyrite with the formation FeOII) oxides plus elemental sulfur. Also there is evidence that Fe oxy-ions form. Coal pyrites, under rapid sweep conditions display only the first two anodic peaks, the associated reduction peaks and an additional reduction peak corresponding to one or more of the high voltage oxidation products. After prolonged exposure to high potentials, coal pyrite displays reactions similar to those of mineral pyrite but at much higher current densities demonstrating the much higher reactivity of the coal pyrite. The reactivity sequence was Upper Freeport coal pyrite > Pittsburgh coal pyrite > mineral pyrite.

Jan 1, 1991

By N. Can

Kinetics and mechanism of the chemical interactions between Si3N4 and TiC were investigated by isothermally reacting samples under nitrogen and argon atmospheres at temperatures between 1600°C and 1700°C? The initial composition of the powder compact contained 20, 30 and 40 volume per cent TiC? Kinetic analysis were performed by measuring mass losses and composition of the titanium carbonitride (TiC1-xNx) at predetermined time intervals? It was found that in the Si3N4-TiC system the degree and rate of the reactions increased with increasing temperature and content of TiC in both nitrogen and argon atmospheres? Si3N4 in the presence of TiC was stable in nitrogen atmosphere and the reactions were confined to Si3N4/TiC and TiC/N2 interfaces? At both interfaces interchange reaction occurs by simultaneous diffusion of nitrogen towards the centre of the particle and desoprtion of carbon in the opposite direction resulting in formation of titanium carbonitrides with various compositions? Reaction products under nitrogen atmosphere were B-SiC, TiCl1-xNx and N2? The maximum "x" value in TiC1-xNx was found to be 0?67 under nitrogen atmosphere? Si3N4 was found to be unstable in argon atmosphere in the presence of TiC and dissociated into liquid silicon and nitrogen gas within approximately four hours of reaction time, depending on temperature? The reaction mechanism in the initial stages of the interaction between Si3N4 and TiC under argon atmosphere proceeds similar to reactions under nitrogen atmosphere? However, considerable amount of Si3N4 dissociates within the first half hour? Liquid silicon aggressively attack both TiC1-xNx and unreacted or partially reacted TiC particles through cracks and pores and diffuses into interier part of the particle forming liquid solutions? After this stage, reactions under argon atmosphere proceeded according to Si-Ti-C ternary system?

Jan 1, 1999

By De-qing Zhu, Jian Pan, Tie-jun Chun, Dong Chen, Yu Cui

"A study of processing pyrite cinder and metallurgical slag using “one step” technology in strand grate - rotary kiln is presented, which aims to efficiently recover the valuable metals of iron, lead, zinc and copper. The effect of chloridizing roasting parameters including roasting time and temperature on the removal rates of nonferrous metals was investigated. It is shown that copper and zinc are difficult to remove and lead is removed more easily. The preheated pellets were reduced in a rotary kiln, where zinc and lead can be removed easily and high iron grade and good metallurgical performance prereduced pellets can be obtained. Furthermore, the chlorination and the reduction mechanisms of copper, lead and zinc are discussed. It is revealed that the phases of copper, lead and zinc in slag are complex and ferrite and silicate of metals are difficult to remove.IntroductionAs two kinds of significant secondary resources, metallurgical slag and pyrite cinder contain not only abundant iron but also considerable copper, lead, zinc and so on. Several tens of millions of tons of metallurgical slag and pyrite cinder are discharged in nonferrous metal and chemical industries annually in China [1, 2]. In addition, the accumulated waste slag in storage is more than one hundred million tons, which not only occupies much land but also pollutes the environment [3]. However, because the metallurgical slag and pyrite cinder are treated by high temperature processing, the properties are distinctly different from the properties of natural ores, and iron is in close association with copper, lead and zinc. So, metallurgical slag and pyrite cinder are difficult to efficiently utilize and only a small amount is used as additives in cement, paving, brickmaking and auxiliary additives [4-7]."

Jan 1, 2011

By Ji-He Wei

The ESR of Cu-Cr-Zr alloy has been experimentally investigated. The remelting experiments have been carried out with different slag fluxes in the Cal, + Nal, CaF2 + ZrO2 and CaF2 + NaF + ZrO2 systems on an ESR furnace of 25kg capacity; using a water-cooled copper mould of 96.5 mm diameter, with the forged square bar electrodes of 50x50 mm2. The slag amount was taken to be 1.5 kg. The remelting current and voltage used were 1600-1800A and !5-25K, respectively. The influence of the slag composition on the stability of the remelting process and the losses of alloying elements (2r and Cr) has been considered and examined. The technologies of hot working and heat treatment of the ES ingot have been described and discussed. Some physical properties of the slag in a CuF2 + NaF + ZrO2 system and the remelted Cu-Cr-Zr alloy have been determined. The results indicated that with the slag flux of CaF2 + NaF + l0 mass % ZrO2 and the other operation parameters employed, a high quality ingot of Cu-Cr-Zr alloy may be obtained at the considerably high yields of Zr and Cr by means of ESR. For the remelted Cu-Cr-Zr alloy with a specified composition of 0.5 mass % Cr and 0.1 mass % Zr, the appropriate electrical conductivity, hardness and softening temperature are as high as 45-46S/m, HRB 82-84 and 550°C. respectively. The properties of the Cu-Cr-Zr alloy products are in accordance with and superior to the requirements and specifications of ISO5l82-l99l(E).

Jan 1, 2000

By R. H. Hanewald

The INMETCO process has been modified so as to recover nickel. chromium and Iron from a wide variety of metal containing waste-streams. This now includes the recovery of metals from spent acid solutions such as chromic acid etching I1quids. nJcke1 and chromium plating solutions; stainless and superalloy pickling solutions. etc. In addition. hazardous electric furnace stainless steel and. superalloy baghouse bags can be processed so as to recover the valuable metall1cs. A detailed review of the above new recovery techniques w1ll be discussed as well as the current operating methods used at INMETCO.

Jan 1, 1992

By Gaballah Djona M.

Spent hydrorefining catalysts contain about 5 % of CoO and/or NiO, 12 % of MoO3 and up to 10 % of V205. They are generally supported by alumina and contain up to 25 percent of C, S and hydrocarbons. Such materials are potentially hazardous to the soil and to water resources. Selective chlorination of raw unroasted samples with Cl2 + air gas mixture had been investigated. At temperatures lower than 600 °C, it was possible to recover more than 90 % of nickel and cobalt chlorides, about 99 % of the molybdenum and up to 75 % of vanadium chlorinated compounds. CoCl2 and Ni/Cl2 were extracted from the chlorination residues by their dissolution with acidified water. Molybdenum and vanadium chlorinated compounds were recovered by selective condensation from the vapor phase. The chlorination of Al2O3 could be limited to less than 6 %. The scale up of this treatment was successful and a flow-sheet is proposed.

Jan 1, 1995

By Dale W. Collins

The disposal of arsenic from copper operations possess various health, environmental and processing problems. There are basically two areas of concern. The first being the disposal or treatment of smelter flue dusts and the second the removal of arsenic from refinery electrolytes. A number of treatment options have been proposed including the addition of soluble arsenic wastes to copper heap and dump leaching solutions. This approach will allow arsenic to be reintroduced to the ore via Solvent Extraction (SX) raffinate associated with hydrometallurgical operations. Knowledge of the attenuation behavior and mechanism during leaching is important in determining the long term stability of arsenic and the success of this approach. Parameters, such as uptake capacity, pH, particle size and solution chemistry have been investigated. Arsenic attenuation has been examined using column leaching with experiments employing both continuous flow and pulsed additions of As(V). In the initial stages of leaching, the attenuation of arsenic appears to depend on the pH and iron concentration in the effluent. Arsenic stability in the copper oxide ore has been examined with rinses of progressively lower pH.

Jan 1, 1994

By Timothy W. Ellis

This paper presents the basic theory of operation, physical chemistry and phase equilibria which allow the development of liquid-liquid extraction circuits based on metallic solvents. The incorporation of reduction and reduction/diffusion processes into the process 'scheme is discussed and a detailed description of ,several liquid-liquid extraction schemes are developed. A synopsis of experimental results obtained using this: method to separate rare earth and other metal based materials will be given.

Jan 1, 1996

By Sheikh Abdul Rezan, M. N. Ahmad Fauzi, Yong Jing Hui, NORLIA BAHARUN, Noor Izah Shoparwe, Srimala Sreekantan

In this paper, the effect of carbon reductant on carbothermal reduction and nitridation of copper-doped titanium oxide (Cu–TiO ) was investigated.

Mar 1, 2017

By Andrea Bernardes

Printed circuit boards (PCBs) of varying compositions have been converted by incineration and following melting into an environmental agreeable slag and a copper-nickel-tin alloy, containing the precious metals. The environmental compatibility of the slag was determined according to the German standard DIN 38414 - Part 4; pollutants' concentration in the lixiviates is smaller than the thresholds of drinking water (CE-Standards). Each experiment the charge were 500g scrap from PCBs and ca. 100g slag forming material. The products were a kind of mullite slag, poor on iron, which was recirculated, and an alloy containing up to 0.3% Gold. With a burner to the retort coal gas, the waste gas was burned without soot, and the produced mixed zinc-lead oxide containing silver was collected in the flue dust.

Jan 1, 1997

"In this paper, a mobile heat treatment furnace from Akkermans Gloeitechniek, a Dutch company, was simulated with Computational Fluid Dynamics (CFD). The furnace is cylindrical with four oil burners, and large metal products such as dredging pumps and impellers can be flexibly heat treated to obtain required microstructure and mechanical properties through stress relief, annealing, hardening and tempering. The furnaces are exposed to the open air, and thus the heat loss becomes significant and varies from day to day and from season to season. Since the temperature of the metal products to be heat treated can only be measured on the surface, the temperature evolution inside the metal could not be tracked in practice. CFD simulation provides a useful tool to predict the temperature evolution within the metal pieces and within the combustion space of the furnace. Energy distribution and heat loss can be subsequently estimated. An overall energy balance through temperature measurement indicted relatively low energy efficiency. Especially during the soaking period, the high energy supplied is barely used to compensate the heat loss of the furnace to maintain a constant temperature of the metal piece. The current CFD modeling aims to give advice on how to modify the design and optimize the operation to reach higher energy efficiency and low heat loss. The CFD model consists of turbulent combustion model, radiation model in participating media, and conjugate heat transfer between the combustion space and solid metal. Temperature measurement was carried out to provide thermal boundary conditions and overall energy balance of the operation. After the model validation with temperature measurement within the combustion space and metal surfaces, furnace optimization will be conducted.IntroductionHeat treatment is a common practice in metal production and manufacturing industries. Through heat treatment at certain temperatures with special patterns, unique mechanical properties of the metals and the metallic products could be obtained. ""Akkermans Gloeitechniek"" is a company situated in K.inderdijk, at location of LHC-Holland (www.ihccaland.com), the Netherlands. Heat treatment of metals is its core business. Various type of heat treatment are applied, such as stress relieving, soft annealing and hardening (quenching), tempering, transformation and precipitation. At the company 6 furnaces are in operation and the 7th is being built"

Jan 1, 2004

By Fei Ruan, Chang Jie, Jieyu Zhang, Jifang Xu, Kuochih Chou

"Viscosity is an important physical parameter of slag in metallurgical processes. Most studies of aluminosilicate and aluminate systems assume that aluminum occurs in tetrahedral coordination. In this case, the O/Al value was utilized to describe the slag structure in terms of the network character of aluminosilicate and aluminate systems. Composition and viscosity data from the literature and the trends were analyzed according to the O/Al value and temperature. It is shown that the O/Al value explains the trends in more than ten systems, containing more than 200 data points. In aluminosilicate system, the trend that viscosity value changed with the O/Al value which implies that alumina works as network modifier such as basic oxides or works as network former. In aluminate system, irrespective of the system and temperature, viscosity decreased steadily when O/Al value increased.IntroductionMetallurgical slags, which are made of oxides and many also contain fluorides, play an important role in metallurgical processes such as iron making, steel making and secondary refining processes. Aluminosilicate slags are applied in a wide range in metallurgical processes. A polymerizing effect of the addition of aluminum and an association of aluminum with low-field strength cations is further supported by the physical variations in aluminosilicate and aluminate systems. The behavior of alumina in silicate melts has been studied by various authors [1-6]. It is generally accepted that Al2O3 is amphoteric [7] because Al3+ ions can behave in profoundly different ways in a silicate melt. When added to a pure silica melt, Al2O3 acted as a network modifier, breaking the bridging oxygen of the pure silica network, thereby decreasing the viscosity in a similar manner to other network modifiers, such as CaO, MgO etc. to form [1/2Ca (AlO4)]4- complexes. However, when added with alkali or alkali-earth metal oxides, some of the Al3+ ions assumed tetrahedral coordination and replaced Si in the liquid network, the missing charge was compensated by Me+ or Me2+ ions. Therefore Al2O3 acted as network former [8, 9]."

Jan 1, 2011

By David Arana

The use of gas-water dispersion of a molten material flow onto a vibrating surface is developed as a process to minimize water pumping requirements, minimize the risks of explosions, and minimize the post solidification dewatering and fines handling equipment requirements. The process uses existing vibration transport technologies and common plant utilities. Plant trials using the smaller footprint and the progressive molten particle cooling time have yielded encouraging results. The results are analyzed and reported.

Jan 1, 2006

By John L. Sundstrom

Complete systems were designed -and are in operation to recycle the effluent streams and to remove impurities from tankhouse. electrolyte, Heavy em¬phasis was placed on making usable products from as many streams as poss¬ible at minimum capital and operating costs. Almost complete recycling: and reuse of water and sulfuric acid were paramount. Techniques used in-clude solvent extraction - electrowinning, evaporation - crystallization and filtration.

Jan 1, 1992

By Sergio N. Monteiro

Polymeric composites reinforced with natural fibers are increasingly been used in several engineering applications, from automotive parts to building construction elements. In addition to the relatively low cost, the natural fibers are also appraised by their renewable and biodegradable characteristics. Fibers extracted from the crust of coconut fruits, also known as coir fibers have been investigated for a possible use in composite materials. In the present work, the coirfiber/polyester matrix interfacial strength was evaluated by means of pullout tests. The variation of the pullout tensile stress vs. the embedded coir fiber length permitted to determine the critical fiber length and, thus, to calculate the interfacial strength. Observations by SEM complemented the results from pullout tests, indicating that coir fibers have a potential for application aspolymeric composites that could replace conventional materials such as wooden and gypsumpanels.

Jan 1, 2006