Search Documents

By S. Y. Tan

The thermal stability of fully silicided NiSi with arsenic doping on silicon was investigated. The aims of the work were to investigate the Ni silicide phase-related issues associated with arsenic dopant and thermal annealing on Ni-FUSI/HfO2/Si and Ni-FUSI/HfSiO/Si gate stacks. It was found that arsenic-incorporation demonstrated some improvement in both morphology and phase stability of nickel silicided films at high processing temperatures regardless underlying gate dielectrics. The correlations of Ni-Si phase transformation and arsenic doapnt with their electrical and physical changes were established by sheet resistance measurements, X-ray diffraction (XRD), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) analysis. Furthermore, the modulation of the work function (WF) of Ni fully silicided gates by arsenic impurity is presented, comparing the effects of dopant (As) on the WF and silicide phases (NiSi and NiSi2). It confirmed that the work function of NiSi can be tuned by implanting arsenic dopant, but it ineffective for NiSi2 phase.

Jan 1, 2010

By C. Lupi

In 1996 the Italian Agency for Environmental Protection (ANPA) has initiated a study of the environmental impact of the industrial sector of steel produced by Electric Arc Furnace (EAF). Within the framework of this study a hydrometallurgical process to treat EAF dusts was considered and developed. The paper describes the zinc and lead recovery from fumes coming from carbon steel production. The zinc extraction consists in acidic leaching followed by SX-EW steps. The leaching sludge containing lead sulfates was treated to obtain pure lead salt and inert solid residue. The whole process, that minimizes effluents by recycling the main liquid streams, has been developed to obtain marketable products. The solid waste, containing spinels, was subjected to elution tests in order to verify its compatibility with environmental regulation. The process, that has been set-up and tested in the laboratories of the University of Rome, will be transferred and studied on a pilot plant in order to assess its industrial and economical feasibility.

Jan 1, 1999

By Guolin Zheng, Jian Pan, Deqing Zhu, Xianlin Zhou

"In ferronickel production, nickel oxide and part of the iron oxide are reduced to metal by agglomeration and smelting in blast furnace. Due to the physical and chemical properties of the laterite ores, a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality. In this paper, the process of pelletization of nickel laterite was developed, and some parameters to strengthen the pelletization of nickel laterite have been optimized. The results show that the compressive strength of fired nickel laterite pellet can reach over 2000 Newton per pellet while firing at the temperature of 1220 °C~1250 °C in 12 min. The product pellet can be used as high-quality burden for blast furnace to manufacture ferronickel.IntroductionIn recent years, the global stainless steel market was developed exuberantly, which greatly promoted the needs of the basic raw material of stainless steel smelting - metal nickel. Currently nickel sulfide ores are only 40% of global nickel reserves, but offer 60% of all the nickel production. However, with the deficit of resources, the nickel sulfide ore (high grade ore) is depleting, so there is an increasing focus on the utilization of low-grade nickel laterite. Recent research has focused on the wet treatment process to utilize nickel laterite, and less on the use of other technologies [1-8]. The economical and efficient technology relies on the reduction of nickel oxide and part of the iron oxide metal by agglomeration and smelting in blast furnace in China. Some domestic steel companies have adopted this process [9, 10]. Unfortunately a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality of fired pellets. In this study, the process of pelletization of nickel laterite was developed firstly, and some parameters to strengthen the pelletization of nickel laterite have been optimized, and the product pellet can be used to produce stainless steel and ferronickel alloy by blast furnace."

Jan 1, 2011

By Sergio N. Monteiro

From the leaves of the sisal plant (Agave sisilana) a relatively strong fiber can be extracted and is nowadays being investigated as a possible reinforcement for polymeric matrix composites. For this purpose, it is important to determine the critical length of the fiber with respect to the matrix to be reinforced. This has never been properly done for sisal fibers in polyester matrix. Therefore, this work characterized the critical length of sisal fibers, with different sizes, embedded in polyester capsules by means of pullout tests. The critical length obtained allowed the sisal fiber/polyester matrix interface shear stress to be calculated. The relevance of these values for polyester composites reinforcement with sisal fibers is discussed.

Jan 1, 2009

By Yuanbo Zhang, Zhixiong You, Daoxian Duan, Guanghui Li, Tao Jiang, Xiaohui Fan

"Presently, high-grade manganese oxide ores are usually utilized by a coal-based reduction roasting process. However, there were some obvious drawbacks, including serious environmental pollution, high energy consumption, etc. The reduction temperature is relatively high (850-900 °C). In this study, a kind of biomass, pine black charcoal, was used as a reductant to reduce low-grade manganese oxide ores. Under the optimal conditions of reduction temperature of 600~650 °C, roasting time of 30~45 min and ratio of ore to reductant 5:1, the leaching efficiency of manganese reached more than 98%. Compared with the traditional coal-based reduction process, the reduction temperature is reduced by 250-300 °C.IntroductionManganese plays a very important strategic role in the national economy, and it is widely used not only in the metallurgical industry, but also in the light industry, chemical industry, medicine, agriculture, etc [1]. The average grade of manganese ores in China is evenly about 21%, which belongs to typical low-grade manganese ores [2]. Therefore, large quantity of high-grade manganese ores is required to import in order to meet the rapid development of Chinese manganese industry. As reported, the conventional treatment of reduction roasting has been widely applied for processing manganese oxide ores, in which coals or reducing gases (CO, H2 or CHi) were usually used as reducers [3]. However, there were some insuperable problems, such as high energy consumption, poor operating conditions, serious environmental pollution, etc [ 4-9]."

Jan 1, 2013

The effect of rare earth element Y (0-2.0at.%) on the microstructure of TiAl alloys at the as cast and rapidly solidified conditions has been investigated. The results show that the addition of Y greatly refined the microstructure of TiAl alloys at both conditions. The refinement is more significantly with higher Y content. The refinement of Y in the cast alloys is attributed to that the strip-shaped Y-rich phase locating on the grain boundaries impedes the grain growth during solidification. In the rapidly solidified alloys, Y-rich phase dispersing uniformly as spherical particles in the matrix acts as heterogeneous nucleation sites which increases the nucleation rate of ??phase during the ????phase transformation, and produces a refined initial microstructure during solidification. Higher cooling rate restricts the grain growth during subsequent cooling.

Jan 1, 2010

By G. C. Yao

Branch and needle-shaped intermetallic compounds of iron, silicon and aluminum normally exist in the molten aluminum. If a suitable amount of manganese metal is added into molten aluminum, the shape of the intermallic compound particles may become lumpish and spherical. According to the difference in electric and magnetic properties of these impurity particles and molten aluminum, these impurity intermetallic compound particles can be separated by applying an alternating magnetic field. In this experiment the alternating magnetic field was formed by a "c" type loop with AC (50Hz) current. The inner vacuum of the fireclay refractory separator is 25xl5xl30mm3 with a lateral baffle inside. The separator was put into the interspace of the "c" type loop. It was found that the longer the separation time, the larger the amount transferred of impurities. The amount of transferred impurities increases with the increase of separation time and intensity of magnetic field. The addition of manganese metal enhances significantly the efficiency of impurity separation

Jan 1, 2003

By Dong-Wei Li, Tao Zhang, Diao Jiang, Zhou Wang

The feasibility of simultaneous vanadium extraction and phosphorus removal from vanadium-containing hot metal was demonstrated with laboratory experimental investigation.The effect of CaO addition on the distribution behavior of vanadium, phosphorus between basic vanadium slag and semi-steel as well as the influence of basicity on the leaching behavior of vanadium, phosphorus was particularly studied. Results show that vanadium oxidation ratio slightly decreases with the increase of basicity, but phosphorus oxidation ratio rapidly increases with the increase of basicity. The leaching of roasted vanadium slag with various CaO contents indicated that the optimal slag basicity for extracting vanadium was 1.5. The maximum leaching efficiency of vanadium could reach 84.02% and the sequence of vanadium leaching efficiency by using different leaching reagents was: 160 g/L Na2CO3 > 100 g/L NaHCO3 > 400 g/L (NH4)2CO3 > 5% H2SO4.

Mar 1, 2017

By Ping Long, Bin Yang, Jian Wu, Xiumin Chen, Wenli Zhang

In this study, the analysis method of trace element in pure indium using glow discharge mass spectrometry (GD-MS) has been established by correcting the analysis result, which was obtained from non-standard quantitative method of GD-MS. The effect of instrument operating parameters, the resolution and isotopes and the pre-sputtering time on the determination results were investigated respectively. The optimized operating parameters of the instrument were obtained as follows: the discharge current was 37.5mA and discharge airflow was 475ml/min. Mass spectral interferences have been eliminated using selected resolution and isotope. The pre-sputtering time was 30 min. 4 trace elements in two pure samples were determined for 6 times. The RSD were less than 20%. The content of trace elements in indium samples was determined by GD-MS and Chemical Analysis Method of Indium which is tested by inductively coupled plasma atomic emission spectrometry, respectively. The results were consistent with each other.

Jan 1, 2016

By L. I. C. Fernandez, E. B. Ferreira Filho, L. G. Pedroti, L. G. Justino, W. E. H. Fernandes, R. C. S. S. Alvarenga

More and more industries have been concerned with the disposal of the wastes generated in their production processes, once this generates a positive impact, both visual and economic enterprise, no more needing to have resources for transport and final disposal of wastes. In this context, and seen the importance of the Portland cement a sa building material, which aims the creation of an ecological cement from the mix of two wastes, the grits, which is a waste generated in pulp production, and the granite beneficiation waste. It proceeded initially with the chemical and physical descriptions of the wastes. Five mixtures, varying the percentages of the wastes and the preparation method of the raw materials, were prepared. After,the blends were sintered in a muffle furnace at 1300 °C for 15 min, forming new compounds that were compared with national cements, according to the Brazilian technical standards. It was concluded that the sintering of the product obtained satisfactory results, presenting good binder characteristics, however, some parameters were outside the limits for common Portland cements such as rapid setting time, large expandability and low compressive strength.

Mar 1, 2017

By Takeshita. Takuo

"In this work, the progress of the HDDR process is discussed mainly on the Nd-Fe-B magnet system. There are three technologies being used for the Nd-Fe-B permanent magnet production; the sintering technique, the rapid quenching annealing and the HDDR process. The HDDR process utilizes· the HDDR phenomenon, in which hydrogen absorbing intermetallic compounds go through as they are heated in hydrogen atmosphere, Hydrogenation - Decomposition Desorption - Recombination. In the HDDR process, these four steps in the HDDR phenomenon are processed by choosing suitable reaction conditions regarding to hydrogen gas pressure, temperature, rate ·of desorption and etc., and we can produce permanent magnet powders of good magnetic properties with microstructures consisting with sub-micron size crystalline grains. In the anisotropic magnet powders, the sub-micron size crystals are being mostly aligned in the crystallographic c-axis direction. Possible applications of the HDDR process to other systems are also discussed.Microstructures of the Nd-Fe-B Permanent MagnetsIt is well known that magnet properties of magnetic materials are very sensitive to their microstructures [l]. This is seen in almost all magnet materials from soft magnetic materials and hard magnetic materials to magnetic memory materials. In this regard, the production technology is very important for the control of microstructures of permanent magnets The Nd-Fe-B magnet is the most powerful permanent magnet as a practical permanent magnet, and its coercivity force is much dependant on the microstructure as is the case for other permanent magnets."

Jan 1, 2000

By Philip Nash, Jie Zhou, Joshua Blackketter

"Large ingots tend to have internal defects such as shrinkage cavities and porosities, which have to be closed during the cogging stage to ensure sound internal quality of forged parts. In this work, finite element methods were used to simulate open die forging passes, with varying parameters that affect the void closure behavior profoundly. Numerical models ware constructed in ABAQUS, DEFORM and FORGE using data taken from footage of the forging process and material mechanical data obtained from the Gleeble compression tests. Forging variables such as pass rotation, reduction per pass, and feed ratio were studied with intense attention paid on the special properties of H13 steel, so that this study can be applied to solve real world problem.IntroductionCenterline defect closure is a frequently studied but still challenging topic in open die forging industry. In practice, open die forging is employed as an effective hot forming process to make desired shape of metal products as well as to ensure center consolidation of internal defects which result from the casting process. Nowadays, remarkable large forgings have been more and more required to meet industries demand. However, the increase in ingot size has tended to result in considerable macrosegregations and shrinkage cavities or voids, which need to be worked thoroughly during the forging process; but the size of the products and limitations of manufacturing capacity, such as the press load, make it difficult to achieve adequate local deformation to close those defects. Therefore, choosing optimal forging parameters under given work condition to ensure good internal quality of forged products is critically important."

Jan 1, 2012

By Jochen Petersen

Design and operation of heap leach processes are still largely based on,operator experience and rule of thumb. Although considered a low-cost, low-tech route for mineral extraction, the underlying physical, chemical and biological processes are actually rather complex. Numerous heap leach models have been devised over time, but the majority of these tend to simplify the true process and are of limited use in practise. The modelling approach presented here combines the more conventional reaction-diffusion model with models accounting for equilibrium reactions in solution, bacterial growth kinetics, complex reactions schemes, gas flow, heat conservation, etc. One particular model application is discussed in the context of developing a novel high temperature heap leach processes using thermophile micro-organisms. The complexity of processes such as this can only be appreciated with the aid of a systematic model. For the designing engineer an accessible, personal computer based model should be an indispensable tool for the design and optimisation of efficient heap leach operations.

Jan 1, 2002

By Shilai Yuan, Huimin Lu, Zhijiang Gao, Panpan Wang

"Solvent refining of silicon through using Si-Al melts is a valid method to remove the impurities from metallurgical grade silicon (MG-Si) melt. The thermodynamic behavior of impurities Fe, Al, Ca, Ti, Cu, C, B and P in MG-Si during the solidification of MG-Si was studied based on the available thermodynamic parameters and experimental data. The morphology of inclusions was investigated by Scanning Electron Microscope (SEM). The chemical composition of inclusions in MG-Si and Al-Si melt was analyzed by EPMA. It is found that the amount of white inclusion reduces and most impurities are solved into the Al-Si melts. After solidification of Si–Al alloy using induction heating and acid leaching, impurities can be effectively removed. The solidification of silicon from the Si–Al melt is found to be more effective for purification than general silicon solidification.IntroductionPhotovoltaic energy is one of promising energy resources in a sustainable society because of its inexhaustibility and cleanliness. Although the production and installation of solar cells have increased significantly during the last decade, the cost of solar cell installation is still high. Multicrystalline silicon has now become the main material in the photovoltaic market because of its low production cost and because of the relative high conversion efficiency of solar cells made from this material, which has been studied for a long time [1-3].Electronic grade (EG) silicon (99.9999999% Si) is commonly used as the raw material to produce SOG-Si (99.9999% Si). Silicon produced from the chemical routes restricts the development of solar cells due to environment threaten, high energy consumption and low productivity. Purification of metallurgical grade silicon (MG-Si) is a low cost, environment friendly method. Although several metallurgical processes such as directional solidification, vacuum refining and electron beam melting [4], have been developed, the cost reduction and refining efficiencies for manufacturing silicon is still have to be further optimized.In the purification process, it is difficult to remove boron and phosphorus by the conventional metal refining method. The refining efficiency depends on the segregation behavior of different elements in solid silicon and the liquid phase. The segregation ratios of all investigated impurities were found to be much smaller than the segregation coefficients between solid and liquid Al-Si melts [5]. For instance, the segregation coefficient of B in Si is 0.8 at the silicon melting point (1687K), whereas it is around 0.2 when silicon is solidified from Si-Al melt at 1273K. For phosphorus the segregation coefficient is 0.06 when silicon is solidified from Si-Al melt at 973K°C, which is much less than 0.35 for recrystallization from liquid silicon. Since the segregation coefficient of boron in silicon is 0.8, it cannot be removed by directional solidification."

Jan 1, 2014

By A. Kiziltas, D. J. Gardner, C. W. Mcllwraith, J. W. Bridge, M. L. Peterson

"Dynamic mechanical thermal analysis (DMTA) tests were conducted on high-oil content, paraffin-based wax used in wax-coated granular composites. These composites make up the surface of synthetic Thoroughbred horse racetracks used in North America. The modulus and damping response from the DMTA tests were correlated with the dynamic triaxial shear strength response of the bulk track material taken at two different operational temperatures and at four strain rates. The purpose of these tests is to understand the mechanisms of shear strengthening of the bulk track material as the wax is heated through the first crystalline solid to liquid nominal transition temperature. Previous work using differential scanning calorimetry confirmed that under common operational surface temperatures, the wax coatings undergo distinct thermal transitions. The resulting increase in triaxial shear strength values affects the consistency of the racetrack which, in turn, can potentially affect Thoroughbred racing performance and safety of the track surface.IntroductionSynthetic granular composite materials are being used in nine Thoroughbred horse racetracks in the United States as well as in other tracks around the world. In one case, their use was mandated by the state of California in 2007 due to testimony that these tracks were significantly safer than traditional dirt tracks [1]. Several synthetic tracks have shown substantial reductions in injuries since switching to synthetics; one California track showed a 75% reduction in catastrophic horse injuries during the first year as compared to the previous year racing on a dirt track [2]. The composition of the tracks in the U.S. generally consist of silica sand (>70%), polymer fibers (<5%), and rubber particles (0-15%) all coated with a paraffin-based, high oil content wax [3, 4]. In a recent study of several synthetic racetracks, to include the track location in this study, the oil content ranged from 34 to over 44% by mass [5]."

Jan 1, 2011

By Fuqiang Zheng, Yufeng Guo, Guanzhou Qiu, Tao Jiang, Xiaoming Qu

MxTi3-xO5 is the main titanium-bearing mineral in the titanium-bearing electric furnace slag (TEFS), which is produced by direct reduction-electric furnace smelting process with vanadium titanomagnetite concentrate in Panzhihua-Xichang region of China. In order to effectively utilize the titanium resource in TEFS, the thermomechanical analysis and conditions for the growing up of MxTi3-xO5 grain were investigated, which emphasized on the effects of CaF2 and cooling rate on the crystallization of MxTi3-xO5 in the melting process. The mineral phase and morphology of titanium-bearing slag were determined by XRD and electron microscope technique, respectively. The results indicated that the average grain size of MxTi3-xO5 grown up from 30 to 92 lm and the area fraction of MxTi3-xO5 reached about 66% from 61% under the conditions of 5 wt% CaF2 and cooling rate at 1 °C/min.

Mar 1, 2017

By Lucas L. da Costa, Sergio N. Monteiro, Romulo L. Loiola, Tammy G. Rodrigues Portela

"The fibers extracted from the petiole of the buriti palm tree are relatively strong as compared to other lignocelluloses fibers, with a potential for composite reinforcement. In this work, polyester matrix composites incorporated with these fibers were investigated for their flexural behavior. Specimens with up to 40% in volume of continuous and aligned buriti petiole fibers were bendtested until rupture. The results showed an increase in both the composite mechanical strength and the stiffness with incorporation of these fibers. A fractograph analysis by SEM disclosed a moderate adhesion mechanism between the buriti petiole fiber and the polyester matrix. This mechanism is apparently responsible for the improved performance of the composites.IntroductionIn recent years, the substitution of energy-intensive synthetic materials for natural ones is being considered in many industrial sectors including automobile, packing and textile [1]. A typical case is that of natural fibers, mainly those obtained from cellulose-based plants also known as lignocelluloses fibers. They have being investigated in the past two decades, aiming to replace synthetic fibers, particularly the glass fiber, commonly used as polymer composite reinforcement [2-8]. From the engineering point of view, lignocellulosic fibers present today important environmental, economical, societal and technological advantages already discussed [7-8]. Moreover, several lignocellulosic fibers are known since the beginning of our civilization and still cultivated or naturally extracted all over temperate and tropical regions of the world. According to Kalia et al [1 ], these fibers can be classified by their origin, as shown in Table 1."

Jan 1, 2011

A molten metal granulator was designed and fabricated at the U.S. Dept. of Energy, Albany Research Center, for granulation of precious metal-bearing alloys and slags. The system was designed to safely granulate a metal alloy at a temperature of up to 1,600°C at a rate of roughly 50 kg of alloy per minute. The primary water jet was supplied by a 18.6-kW, 600 liter per minute pump which provided approximately 600 kg of water per minute through the primary jet. Two 3.7-kW, 150 liter per minute auxiliary pumps provided additional wash water to wet the granulation trough through 4 secondary jets, which were placed at either side of the primary jet. The water supply was closed-loop, including a 37,850-liter supply tank and 22,710-liter recovery tank. Magnetic separators and particulate filters were included for collection of the finest fraction of the granulation product, which cleaned the water sufficiently for continuous recycle.

Jan 1, 2006

By L. Katgerman, R. Van Toi, H. E. A. Van den Akker

"Mould filling simulations are powerful tools for optimizing the characteristics of castings. The robustness of calculational methods for mould filling simulations is generally tested in simple geometries. While a vertical plate has been used often for validation studies, this paper aims at mould filling simulations of a horizontal thin wall casting. Such castings exhibit a strong interaction between heat transfer (solidification), surface tension and gravitational force.The results are presented of a study to validate numerical simulations of mould filling phenomena in a thin wall horizontal casting. Solidification during mould filling is studied computationally. Velocities are measured using Particle Image Velocimetry.INTRODUCTIONIn foundry practice Computational Fluid Dynamics (CFD) is being considered a promising tool to arrive at a better understanding of casting defects introduced during the mould filling period of a casting. The use of CFD is believed to be advantageous in predicting possible defect locations, pouring times, and the lowest possible casting temperature without the risk of cold shuts. In addition, CFD may be used to optimize pouring system geometries [1,2]. As opposed to experimental studies in, e.g., cold water models, CFD allows for the flexible modification of the casting geometry and the pouring system, and for the inclusion of physical effects such as solidification and heat transfer. Thus, a proper use of CFD may lead to a reduction of the casting rejection rate without expensive trial-and-error procedures, and to a decrease of production costs in foundries. Mould filling simulations take a special place in CFD, because a free surface tracking algorithm is required. Over the past decade methods, MAC [3] and SOLAVOF [4], have been extended to 3-D. The robustness of computational methods for mould filling simulations is generally tested in simple geometries [5,6]. While a vertical plate has been used often for validation studies, this paper concentrates at mould filling simulations of a horizontal thin wall casting. Thin wall horizontal castings exhibit a strong interaction between heat transfer (solidification), surfaces tension and gravitational force. The gravitational force in this setting is orthogonal to the plane of flow and has therefore no influence on the shape of the free surface in the plane of flow. Mould filling numerical methods and algorithms have been recently reviewed by Chen et al.[7]."

Jan 1, 1999

By Walter Curlook

An improved process of hydrometallurgical treatment of laterite ores of the limonitic type for the recovery of nickel and cobalt using sulphuric acid has been developed and patented [I]. The major improvement is brought about by recycling a significant portion of the "mother liquor" emanating from the pressure leaching reaction back to the feed preparation stage thereby substituting for all or at least a major proportion of the fresh water that must be added. The amount of process effluent waters is correspondingly reduced. Concomitantly with the major savings in fresh water requirements, a degree of reduction in new sulphuric acid requirements is effected, along with a savings in limestone and lime required for subsequent neutralizations. Keywords: Acid pressure leaching; Nickel laterites

Jan 1, 2004