Search Documents

By S. K. Kawatra

"A typical steelmaking facility produced 50,000 tons per year of slag in their hot-metal desulfurization process. This slag had a sufficiently high iron content that it could be beneficiated and recycled in a blast furnace, provided that the slag could be agglomerated into pellets suitable for use as blast furnace feed. In this work, beneficiated slag was agglomerated using both a conventional bentonite binder, and a fly-ash-based binder (FBB) that was formulated by the investigators. The FBB consisted of a combination of highcarbon fly ash with calcium hydroxide activator, allowing the FBB to exhibit binding properties when moistened. It was determined that beneficiated slag agglomerated with FBB had superior compressive strengths compared to slag agglomerated with conventional bentonite binder. The FBB is therefore a satisfactory method of binding the agglomerated slag. Since the fly-ash component of the FBB is commonly discarded as waste, this approach also provides a means for utilizing high-carbon fly-ashes that currently have very little commercial value.IntroductionIn 2006 approximately 72.4 million short tons of fly-ash were produce in the United States [1]. The majority of fly-ash which was used that year was consumed concrete, structural fills, and cement. It is also used in road base, aggregate, and other applications. However, 55.2% of the fly-ash produced in 2006 was not utilized and ended up being sent to a landfill. Essentially all of the land filled fly-ash could be a suitable binder for pelletizing desulfurization slag and other steel plant waste oxide materials. Fly-ash based binders (FBB) have been shown in laboratory studies to be suitable for producing iron ore concentrate pellets of equivalent strengths as those bonded with bentonite [2,3,4]. The utilization of highcarbon fly-ash within the market is important for reducing the volume of currently unmarketable and land filled fly-ashes. FBB would be a much cheaper alternative to the current bentonite binder or organic binders used for iron ore concentrate and would help to reduce pellet costs. Currently, transportation more than doubles the final cost of bentonite since it is produced hundreds of miles from the pelletizing plants, while fly-ash is produced from power plants located nearby pellet plants and steel mills. FBB’s also show promise for use in other high volume applications such as foundry sand mold binders."

Jan 1, 2008

By Fuxing Yin, Akira Sato, Yoshiaki Ohsawa, Kohji Kawaharai

"INCRAMUTE alloy (nominally 45Mn-53Cu-2Al wt. %) has a specific damping capacity as high as 0.4, through a solid-solution and aging treatment. The damping behavior of the alloy is highly temperature-dependent and shows a peak near room temperature. The inadequate strength in the high damping condition restrains the practical application of the alloy, as structural components. Ferromagnetic MnB particles are dispersed in the alloy during induction remelting the matrix alloy in an argon atmosphere. Surface modification of the MnB particles by mechanical alloying (MA) and suitable control of the addition process cause a homogeneous distribution of MnB particles in the alloy. In the composite containing 2 wt. % MnB particles, temperature dependence of damping capacity is improved, and higher damping capacity is still retained in the temperatures over 60 °C. Meanwhile, the Young's modulus and tensile strength were also increased by about 20%. The roles of the MnB particles in improving both damping behavior and mechanical properties were also discussed.IntroductionMany viscoelastic materials, such as rubbers, polymers and plastics, have the superior ability to damp vibration and noise. However, in the applications as structural materials the high damping capacities of materials are pursued upon the satisfactory mechanical properties, especially those at elevated temperatures. Damping alloys are finding more and more applications in structures where noise and vibration ·should be ·eliminated. Specific damping capacity (SDC), defined as the ratio of the energy dissipated to the maximum vibration energy stored per cycle, is usually used to evaluate the damping capacity of alloys. INCRAMUTE damping alloy, developed by the International Copper Research Association, Inc., has a nominal composition of 45Mn-53Cu-2Al in weight percent. The high damping· microstructure of this alloy is obtained through the solution treatment at 820 °C followed by a water quench and aging at 400°C for 10 hours followed by cooling to room temperature [1]. With the heat treatment, a SDC peak ·vs. temperature of as high as 0.4 was observed in the alloy at the strain amplitude of about 10-3 while a tensile strength of about 500MPa was sustained."

Jan 1, 2000

By Jun Zhu, Jilai Xuel, Tao Li

"Coal gangue is industrial waste containing Al2O3 and SiO2 with great recycling and reuse values. This work is aimed at extracting Al2O3 content in the coal gangue by a process of carbonthermal reduction - alkaline leaching. The Al2O3 and SiO2 contents first became a mixture of SiC and Al2O3 in the process of carbonthermal reduction, and then Al2O3 was separated by leaching in NaOH solution, thus producing the sodium aluminate solution for Al(OH)3 precipitation. The products generated at various stages in the process were inspected using XRD and chemical analysis. The effects of parameters such as reduction temperature, carbon ratio, NaOH concentration, leaching time, leaching temperature, stirring speed, etc were investigated in details.IntroductionCoal gangue is an industrial residue resulted from the process of coal mining and washing, accounting for 100 - 150 kg with 1 ton raw coal mined. The existence of coal gangue in large quantities has become a serious problem for environment pollution. On the other hand, the chemical compositions of coal gangue are Si02 and Ah03 primarily. In China, the accumulation storage capacity of Ah03 in coal gangue is not less than 600 million ton at a rough estimate, which should be considered as an abundant second resource [1]. If the alumina can be recycling and reused effectively from coal gangue, it will not only reduce the imperilments caused by coal gangue, but also yield good economic returns.Generally, the processes of extracting Al2O3 from coal gangue can be divided into acid leaching (vitriol or hydrochloric acid) and alkaline leaching (mostly NaOH) [2]. The acid leaching processes have many problems, such as lower leaching ratio, corroding the equipments, recycling the spent acid hardly, etc. The primary matter of alkaline leaching process is silica dissolving with alumina, which brings perplexing desilication process, alumina loss seriously and higher energy consumption."

Jan 1, 2011

By Yuuki Hagio, Hiroyuki Tobo, Michihiro Kuwayama, Yasutaka Ta

"Reduction of CO2 emission is necessary to remedy global warming, however, promising approaches of CO2 separation require a large amount of energy. Molten slag, which is generated as by-product of steel production, has high temperature, but its energy has not been harnessed. To recover the thermal energy from the slag and to apply to separation of CO2 are economical and environmental conscious ways. We propose a new heat recovery system, in which, molten slag is solidified continuously on water-cooled roll and the solidified slag plates are charged into counter-current heat recovery equipment. In laboratory scale experiments, heat recovery ratio of more than 30% was acchived by controlling the thickness of slag.IntroductionThe steel industry in Japan has been working on the projects of ""Environmentally Harmonized Steelmaking Process Technology Development (COURSE50)"". COURSE50 aims at developing technologies to reduce CO2 emissions by approximately 30%. One of the main technologies is to capture and recover CO2 from blast furnace gas using chemical absorbents to regenerate CO2-laden chemical absorbents by separating CO2 from the absorbents. As one of the solutions, JFE Steel Corporation has been developing sensible heat recovery process from steelmaking slag. It is effective to recover and use unutilized high temperature waste heat within a steel plant as the thermal energy required."

Jan 1, 2012

By Susumu Okabe

Top blow injection has been applied to continuous copper smelting and converting by Mitsubishi Materials Corporation since 1974. In this process, injected feeds are captured by and dispersed in the molten bath immediately and effectively, and the reaction is enhanced by the agitation of the bath. The continuous motion of the molten bath, however, may cause severe damage of furnace lining materials, if the injection is not controlled and the furnace is not designed properly. In order to suppress refractory wear, especially at the bath line, surface wave of the molten bath should be moderated. A cold model study was carried out with water bath in a cylindrical vessel and the physical model was derived which correlates the oscillation of gas jet impingement on the bath surface and the surface wave. It was found that a half of the proper frequency of the gas jet impingement coincides the proper frequency of the surface wave.

Jan 1, 1998

By Derek Fray

Molten salts have been used for the extraction of metals since the 19th century but, recently, many interesting processes have been investigated using mixtures of molten salts and different cathodic materials. In several existing processes, the cation is simply discharged from melt but, in some cases, complications arise when the electrode potentials of the cations are relatively close. For example, the co-deposition of sodium with aluminium in the Hall-Heroult process is discussed in terms of electrode potentials of the components in the molten electrolyte. Similar considerations will also be given to the anodic reactions with respect to chlorine, oxygen, carbon dioxide or monoxide evolution from chloride-oxide melts. In some cases, the cathodic product interacts with the cathode to produce new and exciting products such as nanotubes from carbon or titanates and reduced titanium oxides from titanium dioxide. Depending on the electrode potentials, it is also possible to completely change the cathodic reaction from discharge of the cation in the salt to ionisation of the anions in the cathode. Examples are given of the reduction of metal oxides to produce metals, high technology alloys and nanomaterials and the cathodic refining of liquid metals.

Jan 1, 2006

By A. V. Tarasov

Regeneration of carbide waste from hard-alloy (sintered carbide) manufacture is an important scientific and technical objective aimed at improving the degree of recycling of rare metals (W, Co, Ta, Ti, Nb). Currently, the degree of recycling of those metals does not exceed 25% to 35% of their total production even in industrially developed countries. This is attributed to a significant extent to the substantial drawbacks of the technologies applied for their processing (environmental pollution, limitations to the use of regenerated products for important applications, sophisticated equipment to be used). An innovative environmentally sound technology has been developed in the Institute of Metallurgy of the Russian Academy of Sciences (IMET RAN) for processing of carbide waste of WC, TiC, TTC and other carbides using asymmetric alternating current of industrial frequency (the electrolyte used for this purpose is nitric acid solution). The current efficiency under optimal conditions is as high as 96% to 98%. The process has been tested on bench scale. The following commercial-grade products are obtained: pure ammonium paratungstate, tungstic acid, cobalt oxide, titanium dioxide and tantalum-niobium concentrate. The total metals recovery is 98% to 99%.

Jan 1, 2006

By Toshiaki Tsuru, Takeshi Ohgai, Hisaaki Fukushima, Shigeo Kobayashi, Tetsuya Akiyama

"Electrodeposition behavior of Zn-Cr alloys from the methanol baths was investigated. In the methanol baths of low Cr3+ concentration, Cr (III) compound was incorporated in the deposits and no lusfrous Zn-Cr alloys was deposited. However, Cr was existed as metallic state in the deposits obtained from the baths of higher Cr3+ concentration. With an increase in water content in the baths, the chemical state of Cr in the deposits changed from metallic to trivalent state. Under the condition that metallic Cr can be electrodeposited, Zn deposition was significantly polarized to the potential of Cr deposition.INTRODUCTIONAn attention has been paid to Zn-Cr alloy plated steel sheet because of its excellent properties for body panels of automobile and electrical appliances [1]-[4]. This plating process can be operated using the sulfate solutions containing Cr3+ ion [1] - [6].In decorative single Cr plating, on the other hand, many attempts have been made to electroplate Cr from trivalent electrolytes, which is motived by environmental deficiencies of the presently used hexavalent process [7]. [8]. However, it has been reported that in the aqueous solutions the behavior of the electroreduction of 0 3+ is atypical due to the complicated nature of the chemistry and electrochemistry of cr3+ species [9]-[11]. Even in Zn-Cr alloy plating, it is difficult to codeposit metallic Cr with Zn in simple sulfate electrolytes [l]-[4], [12]. Therefore, it can be expected that the electrodeposition behaviors of Zn-Cr alloys as well as Cr are significantly changed when the electrodeposition is conducted in non-aqueous plating solutions.In this study, the electrodeposition of Zn-Cr alloy was conducted from methanol solutions to clarify the electroreduction mechanism of Cr3·-Cr0 in the alloy deposition process."

Jan 1, 2000

By Signe Kjelstrup, Leiv Kolbeinsen, Marit Takla, Odne Burheim

"This paper presents a Seebeck-type solid state thermoelectric power generator unit, designed to investigate the possible recovery of radiant waste heat at a silicon plant in Norway where roughly 703 of the total input energy leaves the process as waste heat. The unit is 0.5 m x 0.5 m and is built of 36 commercially available thermoelectric devices based on bismuth telluride p - and n - type semiconductors. Thermoelectric devices directly convert fractions of a heat flux into an electric current (and vice versa) and may therefore be convenient for recovery of waste heat when the heat source is discontinuously available. The purpose of the thermoelectric unit is to give a proof of principle of direct thermoelectric energy conversion on a large scale. We present the initial test results for the generator. At an average temperature difference between the heat reservoir and the heat sink of 98°C, we measured an open ciruit potential of 23.44 ± 0.06 V and the matched load power output was 39.4 W. At a temperature difference of 220°C, we predict the generator open circuit potential to be 40.8 V, which corresponds to an efficient Seebeck coefficient of 242 µV /K, and matched load power output to be 120 W.IntroductionThe world's power demand increases, driven by population growth and increase in living standards and simultaneously global warming is recognized as one of our most serious environmental problems. According to the International Energy Agency[l], the industrial sector accounted for approximately one third of the total global power consumption in 2005. Increasing the energy efficiency of industrial processes thus represents a benign and substantial route for addressing environmental concerns and energy security.In accordance with the second law of thermodynamics, all real processes are associated with lost work which is energy being dissipated as heat to the surroundings[2]. Improving the energy efficiency of industrial processes is about finding the process path associated with a minimum of lost work. The more evenly the losses are distributed, the smaller are the losses [3, 4]. In addition, exploiting the unavoidable waste heat will contribute to improve the energy efficiency. The waste heat may be utilized for heating purposes and/or it can be upgraded to work for instance via some sort of heat engine."

Jan 1, 2012

By Hiroyuki Sano

A closed recycling process for the low-grade scrap of Al-based composite materials was developed. In this process flux treatment with water-soluble halide is a key technique. In the present work, flux treatment conditions were discussed from the viewpoint of the separation and the recovery of the base material, reinforcement and flux. Optimum separation condition was obtained for the NaCl-KCI-KF flux treatment. The recovered aluminum alloy can be recycled for various usages. The recovered SiC particles cannot be reused as reinforcement because of the coexistence of the contamination, therefore it is necessary to eliminate these contaminates or to find another use. The recovered flux is reusable with supplemental addition of fluoride.

Jan 1, 2003

By Noriaki Kurita, Norihiko Fulcatsu, Teruo Ohashi

"An electrochemical sensing device for hydrogen in molten metal has now been available owing to the development of the proton conducting solid electrolyte made of ceramics of metal oxide. The structure of the sensor and the theoretical limitations of its applications are discussed based on the electrochemical properties of the electrolyte used. The practical performance of the sensor is reviewed from the results of test measurements at the plants of aluminum and copper melting industries. The effectiveness of the sensor to the process control of continuous casting of copper is also discussed.IntroductionSince the in-line monitoring of the amount of oxygen dissolved in molten metal was realized by using the oxygen concentration cell based on zirconia solid electrolyte a similar method has been expected to be developed for sensing of hydrogen, which is a very important element of gas species in liquid metals, especially, in aluminum and copper. In 1981; Iwahara and coworkers found the dominant proton conduction at a high temperature in some perovskite-type oxide (1). Since then, the effort has been made to apply this proton conducting material as the electrolyte of the hydrogen concentration cell for high temperature use. The hydrogen sensor for liquid aluminum of this kind was first produced in 1991 (2) and released commercially from TYK Co., Ltd. Recently, we have developed the mother one usable at higher temperature such as copper and silver melting processes (3). In this note we discuss their structure, design and applicable limitations based on the electrochemical properties of this new type electrolyte. The performance of the sensor and benefit to use it to control the melting process is also discussed"

Jan 1, 2000

By H. Aminian

Copper electrowinning (EW) is an important process in connection with the solvent extraction to produce pure and marketable copper cathodes. A phenomenological model was developed to simulate the copper electrowinning process. The simulator is used to predict the operation of the Mines Gaspe pilot plant electrowinning cells put in operation in 1996. Results confirm the potential of the simulator that would subsequently be used for student training, process optimization and assessing the performances of control strategies.

Jan 1, 1999

By Zhang Chuanfu, Tan Pengfu

"A thermodynamic model is developed to predict the distribution behaviors of Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag in copper pyrometallurgical process. In this model, as more as 21 elements (Cu, S, Fe, Ni, Co, Sn, As, Sb, Bi, Pb, Zn, Au, Ag, 0, N, C, H, Ca, Mg, Al, and Si) and 72 compounds (in fayalite-slag-making system) or 74 compounds (in ferrite-slag-making system) are considered. Accessory-element behavior is studied for two types of slag , fayalite and ferrite, and two levels of oxidation. The allowance is also made to account for physical entrainment in the melts.-Model simulations are carried out to study the effects of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxygen enriched air. The model can be used in copper flash process, Mitsubishi process and Noranda process. The predictions by the present computer model are compared with the known industrial data from Gui Xi Smelter in China, Home Smelter in Canada and Naoshima Smelter in Japan and excellent agreement between calculations and industrial data is obtained. In this paper, the effects of oxygen enrichment, matte grade, smelting temperature, and types of slag on accessory-element behavior among matte, slag and gaseous phase have been elucidated.I . IntroductionThe presence of trace quantities of minor elements such as As, Sb and Bi in copper significantly reduces its ductility, electrical conductivity, and lowers its thermal conductivity. Embrittlement of copper also occurs due to impurity-phase precipitates at the copper grain boundary interfaces. They deteriorate not only the electrical conductivity of copper but its workability in hot working."

Jan 1, 1998

By Michael Sheedy

Sulfuric acid is widely used as an electrolyte for the electrorefming and electrowinning or metals. Impurities in this electrolyte are controlled by continuously bleeding solution from the tank house. In addition to the contaminant these bleed streams contain high levels of sulfuric acid and the metal being recovered. Subsequent treatment of these bleed streams often requires neutralization which generates large volumes of solid waste. Absorption resin technology employing a novel ion exchange technique known as Recoflo® allows the separation of the mineral acid from dissolved metal salts. The recovered acid is suitable for recycle back to the electrolyte circuit. The metal salt and other contaminants leave the process free .of the sulfuric acid. In this process, known commercially as the APU®, ion exchange resin is used to sorb sulfuric acid while excluding the metal salts. The purified acid is then removed by washing the resin with water. The process has been extensively used for the recovery of waste pickling acids in the steel industry and anodizing solutions in the aluminum industry. In the mining and metallurgical industries the process has been successfully evaluated for the separation of excess sulfuric acid from copper electrolytes, the removal of magnesium and manganese contaminants from zinc electrolytes, and nickel and copper from copper electrolytes. A full scale installation on a copper refinery bleed stream at Palconbridge's Kidd Creek plant in Timmins, Ontario has now been operating successfully for more than 1 year while pilot field trials have been successfully completed on other applications.

Jan 1, 1997

By Jingwei Lou, Bing Li, Suzhen Li, Miao Shen, Jianguo Yu

"As a main impurity in primary lithium metal, magnesium is difficult to remove because of the very close relative volatility of the two metals. Electrochemical refining provides a possibility to completely remove Mg in the LiCl-KCl melt prior to Li reduction. MgCl2 reduction processes in LiCl-KCl- MgCl2 melt were investigated by cyclic voltammetry (CV), square wave voltammetry (SWV), chronoamperometry and chronopotentiometry. Then potentiostatic electrolysis was carried out and Mg (II) ion was reduced onto a liquid lead cathode from the LiCl-KCl-MgCl2 melt at the Mg deposition potential. The results show that Mg ( II ) is reduced in one step with two-electron transfer. The reduction potential of Mg ( II ) was well defined. The reduction of Mg( II) results in Li ( I ) underpotential deposition at 0.2V more negative potential than that of Mg( II) reduction. Therefore, in order to prevent Li ( I ) from codeposition with Mg, accurately controlling Mg ( II) reduction potential during the potentiostatic electrolysis was necessary. Ninety three to 99 % removal rate of MgCl2 was achieved after 8-12 h electrolysis when liquid lead was used as cathode.IntroductionMetallic Li has been widely used in batteries, light weight alloys and in fusion reactors because of its excellent properties. Currently, the only way in industry to produce metallic Li is by electrowinning from molten LiCl-KCl at about 450 °C [l-5]. LiCl-KCl is the only electrolyte used, because they presents a lower eutectic temperature and KCl shows a slightly higher theoretical decomposition voltage than LiCl, as shown in Table l .The produced metallic Li generally contains 1-2 wt% impurities including Na, K, Al, Ca, Mg, Si, etc. [6l, which are derived from the corresponding metal chloride compounds or metal oxide compounds existing in the LiCl and/or KCl raw materials. These impurities have to be removed by subsequent vacuum distillation at high temperatures to meet the requirements for metal Li purity in the final products. Separation of Mg from Li by vacuum distillation is difficult because their relative volatilities are very close, as shown in Table 2."

Jan 1, 2011

By I. M. Richardson, M. Janssen, I. J. Bennett, V. A. Popovich

The most critical processing step during the manufacture of screen-printed crystalline solar cells is firing aluminium and silver contacts, which generates residual stresses and solar cell bowing. In this paper, an alternative Ag contact formation mechanism is proposed and aspects related to electrical contact properties, residual stresses and layer delamination are investigated. It is found that there are two main processing parameters affecting the uniformity and delamination of the Ag/Si interface, namely the peak firing temperature and the silicon surface roughness. Silicon surface polishing gives a better wetting of the silicon surface by the glass layer, resulting in a good contact and lower incidence of large voids, compared to the case of highly textured surfaces. The non-uniformity in the glass layer and large voids at the Ag/Si interface (in the case of a textured surface) are expected to have a negative effect on the mechanical strength of the solar cell.

Jan 1, 2015

By Mark Samonds

"Manufacturing processes which involve liquid to solid and solid state transformations in metals encompass a wide variety of physical phenomena. The past twenty years have seen a steady evolution in the complexity and scope of numerical models of these processes, beginning with thermal analyses without phase change. Recently, a few software packages have become available which have true multi-physics capabilities. This permits the treatment of thermal, fluids, stress, electromagnetic, chemical reaction and microstructure development aspects altogether in a fully coupled simulation. This paper will consider various aspects of these types of models.Coupled thermal and fluid flow analyses of continuous castings have been around for fifteen years. Coupled thermal and free surface fluid flow simulations of shape castings have been available for ten years, including view factor radiation models for investment castings. Only recently, however, have fully coupled thermal, fluid, and stress analyses become practical. This implies the reverse coupling of the mechanical deformations to the solution of the energy and momentum equations through modification to the interface heat transfer coefficients and the fluid domain geometry. This has been implemented with a combined eulerian-lagrangian finite element method. Appropriate mechanical constitutive models will also be discussed.Many types of defects need to be predicted in casting processes. Those related to stress include hot tearing, hot cracking, part distortion, and thermal fatigue in dies. Macroporosity, microporosity, and microsegregation are determined by the solidification behavior and microstructure development in a casting. In particular, microporosity is influenced by dissolved gases, the morphology of the mushy zone, the liquid to solid density change, and the local pressure conditions. Macrosegregation is caused by the partitioning of solutes during. solidification and subsequent thermo-solutal convection. An additional transport equation is required for each solute that is being tracked. Computational thermodynamics is being incorporated into these types of analyses to determine transformation temperatures, partition coefficients, densities, and enthalpies. In combination, the microstructure and microporosity models can frequently predict a variety of mechanical models, such as yield strength, tensile strength, and elongation."

Jan 1, 2001

By Takahiko Okura

Most non-ferrous raw materials are associated with sulphur. To extract the metals, the sulphur is recovered typically as sulphuric acid or liquid SOz, On the other hand, natural gas may contain over 20% of hydrogen sulphide (HzS) and a huge quantity of elemental sulphur is produced through oil and gas refining processes in the world. A large fraction of the sulphur mined from natural sources is eventually returned to the earth as fertilizers, by-products of desulphurisation and neutralisation processes, or as fugitives to the atmosphere. However, the supply and demand for sulphur are in imbalance. Such situation urges to develop a new smelting process without sulphuric acid production. This paper briefly reviews the global sulphur balance and the technologies for recovering elemental sulphur. The core of this paper is a proposal to convert SO2 gas to elemental sulphur by using organic materials. Some results of thermodynamic calculations and experiments are presented.

Jan 1, 2003

By Takahiko Okura

Most non-ferrous raw materials are associated with sulphur. To extract the metals, the sulphur is recovered typically as Sulphuric acid or liquid S02. On the other hand, natural gas may contain over 20% of hydrogen sulphide (H2S) and a huge quantity of elemental sulphur is produced through oil and gas refining processes in the world. A large fraction of the sulphur mined from natural sources is eventually returned to the earth as fertilizers, by-products of desulphurisation and neutralisation processes, or as fugitives to the atmosphere. However, the supply and demand for sulphur are in imbalance. Such situation urges to develop a new smelting process without sulphuric acid production. This paper briefly reviews the global sulphur balance and the technologies for recovering elemental sulphur. The core of this paper is a proposal to convert S02 gas to elemental sulphur by using organic materials. Some results of thermodynamic calculations and experiments are presented.

Jan 1, 2003

By Hitoshi Iijima, Fumitaka Tsukihashi

"Fine powder of tantalum is used as materials of electric condenser. It is important to control the distribution of particle diameter of tantalum fine powders for the commercial use. In this study, fine powders of tantalum were produced by reducing tantalum chloride vapor with hydrogen gas at 1673 and 1773K. The tantalum chloride vapor was reduced with hydrogen and the produced fine particles of tantalum were collected to observe the distribution of particle diameter. The effects of reaction temperature, partial pressure of hydrogen gas and vaporization temperature of tantalum chloride on the distribution of particle diameter and reaction efficiency of reduction were determined. The mechanism of reduction reaction of tantalum was discussed.IntroductionThe ultra fine powder shows various different physical properties from that of bulk materials. Therefore, the application of ultra fine powder to various fields such as magnetic material, electric material, catalyst, etc is anticipated. The control of shape of powder, size distribution, property of agglomeration, purity is required for the practical use of ultra fine powder. Although the ultra fine powders of ceramics are produced by various methods, the ultra fine powder of metals are produced by the evaporation in gas atmosphere, plasma evaporation process, chemical vapor deposition process, and reduction and precipitation in liquid phase depending on the metal and productivity. The chemical vapor deposition process has features that pure metal powder can be obtained and the control of the distribution of powder size is easy. [1,2,3,4,5]"

Jan 1, 2000