Search Documents

By F. M. Swain

High-calcium limestones occur in the upper part of the New Market Formation, of Lower Middle Ordovician age, in Franklin and Cumberland Counties, Pennsylvania. The high-calcium facies of the New Market Formation is represented by sublithographic limestone or vaughanite, which probably formed in quiet water; low-energy environments such as intershoal lagoons, or in protected bays similar to the present-day Florida Bay environment. Rapid facies changes are characteristic of the strata. The better grade of stone lies in the upper 100 to 125 feet of the New Market Formation and averages 95-97% calcium carbonate. Silica and magnesia are about equal in amount as impurities. One high-calcium belt extends from the Maryland state line through Chambersburg and Newville to beyond Carlisle. The strata in this belt are structurally complex, which requires careful field study' and core-drilling prior to exploitation. Stone suitable for blast-furnace flux is present in relatively large amounts, but stone for open-hearth use or portland cement requires more selective quarrying.

Jan 1, 1966

By Patrick J. Hannigan, William H. Walton, Ryan C. Rusk, Van E. Komurka

"The project consists of a 33-story building with two levels of below-grade parking across the entire building footprint. Timely and cooperative teamwork among the owner/developer, geotechnical engineer, testing agency, structural engineer, construction manager, and pile-driving contractor resulted in an efficient, costeffective, high-capacity driven-pile foundation on a constrained urban site with significantly variable subsurface conditions. Design objectives included utilizing the highest allowable pile loads reasonably installed from a drivability perspective, using readily available equipment. A pre-production test program was performed on 16-inch-diameter (406-mm-diameter) steel pipe piles, driven closed-ended and subsequently filled with concrete. The test program included dynamic monitoring of 10 piles during installation, and of select piles during long-term restrike testing with a drop hammer, with one instrumented static load test. CAPWAP® analyses were performed on both end-of-initial-drive and beginning-of-restrike dynamic test records. The site exhibited significant soil set-up, even after relatively short wait times. Testprogram objectives included characterizing set-up profiles. A design set-up profile was used to develop depth-variable driving criteria for both 500- and 600-kip (2,224- and 2,669-kN) allowable load piles. Test program results permitted more-accurate reduced capacities to be assigned to damaged piles, and to piles which experienced practical refusal. These more-accurate assigned reduced capacities decreased the number of replacement piles required by 50 percent, saving both time and cost.PROJECT DESCRIPTIONThe project, located in Milwaukee, Wisconsin, USA consists of a 33-story mixed-use residential building with two levels of below-grade parking across the entire site footprint. Column service loads range from 1,400 to 4,200 kips (6,228 to 18,683 kN). The project is located immediately adjacent to an existing two-story masonry retail building with a partial basement, supported on shallow spread-footing foundations.Subsurface Conditions – The generalized soil conditions are presented in Fig. 1. Site grades were relatively level, with a ground-surface elevation of approximately +53 feet (16 m), Milwaukee City Datum (“MCD”). Fill material from previous construction was encountered to approximate Elev. +33 feet (10 m). Below the fill, medium dense silty sand, to silt with sand, was encountered to approximate Elev. +23 feet (7 m). Underlying deposits consisted of lean clay, with undrained shear strengths ranging from approximately 1,000 to 3,000 pounds per square foot (psf) (48 to 144 kPa). Silty sand, to silt with sand, exhibiting increasing relative density with depth, was found below the lean clay to approximate Elev. -92 feet (-28 m), where hard lean clay (glacial till) with undrained shear strengths in excess of 5,000 psf (239 kPa) was encountered. Borings did not extend below Elev. -103 feet (-31 m)."

Jan 1, 2017

By Matt Fenwick, Douglas R. Schwarm

Stringent underwater noise limits at the Fairview Ave. N. bridge replacement on Seattle's Lake Union required an innovative approach to supporting the 470-ft long drill trestle. Screw-in foundations would reliably mitigate noise, but the required 500-kip bearing resistance were an order of magnitude higher than typical helical piles. This paper describes the process of designing, installing, monitoring, and testing 22-inch dia. helical piles 80 feet long with 36- and 42-inch dia. helices. A static load test confirmed that the conventional k-factor design method can be extended to capacities of up to 800 kips. A 375 ft-kip drive mechanism had to be fabricated because no North American equipment could supply the necessary installation torque. Real time installation monitoring and later "re-torque" tests confirm that helical piles gain capacity with time, analogous to driven piles under restrike. Underwater and on-land measurements confirmed very low noise, suggesting the possibility of widespread adoption where similar limits are imposed. Overall, this case history illuminates the need for innovative deep foundation types in response to ever-increasing regulatory constraints.

Sep 8, 2021

By Derek Brennan, Donald Brennan

"The existing Rondout West Branch Tunnel (RWBT) is part of the Delaware Aqueduct which has been in service since 1944 and accounts for more than 50 percent of New York City’s water supply. In early 2015, the New York City Department of Environmental Protection contracted Kiewit-Shea Constructors, AJV (KSC) to construct the Rondout West Branch Bypass Tunnel project (Rondout) in order to mitigate the leakage of 132 million L/ day (35 million gpd) of water from two areas of the existing tunnel; the Roseton and Wawarsing areas.The scope of the Bypass Tunnel 2 project is separated into two distinct phases. Phase 1 consists of completing the shaft sinking to a depth of approximately 274 m (900 ft) at shaft 5B, 213 m (700 ft) at shaft 6B and the excavation of approximately 3,850 m (12,500 linear ft) of tunnel at a diameter of 6.6 m (21 ft 7 in). This phase also includes the installation of 2,804 m (9,200 linear ft) of 4.8 m (16 ft) diameter steel interliner pipe through the new bypass tunnel with cast-in–place concrete liner for a finished diameter of 4.2 m (14 ft). Access chambers at the top of shafts 5B and 6B will be constructed for access and housing of the mechanical and electrical equipment for supporting pumps and valves.Included in phase 2 is the additional excavation from shafts 5B and 6B to the RWBT, and the drainage tunnel to remove ground water infiltration from RWBT. This work will be completed during a scheduled shutdown of the RWBT and will include approximately 31 m (100 ft) of excavation of the two connection tunnels. Additionally, construction of the permanent plugs within the RWBT will be undertaken. Figure 2 shows the layout of the work.Access to the work through the deep shaft at site 5B was critical to the success of the project. The hoisting system needed to be multi-functional to handle the different types of construction from drill and shoot of the shaft, starter and tail tunnel, the assembly of the tunnel boring machine (TBM), the excavation of the TBM tunnel including the supply of the precast segmental liner, the grouting operations, the installation of the steel interliner pipe and the cast-in-place concrete as well as ingress and egress of personnel. The production of the TBM operations was critical to the schedule of the project. This required a quick cycle for muck haulage and supply of the precast segmental liner in order to keep pace with the excavation time of the TBM. For TBM assembly, components were limited to a maximum weight of 104 t (115 st) for a single lift. Various cranes were analyzed for hoisting, however, none would meet all of the citeria. Therefore, the project team selected a specialized hoisting system designed in house in conjunction with Timberland Equipment Ltd. that consisted of a total of 14 separate hoists and winches with a total of more than 2,833 kW (3,800 hp)."

Mar 1, 2019

By James Weaver

During the past 16 years, the authors have successfully used high-capacity rock anchors installed inside open-ended pipe piles, driven to bedrock, to provide uplift and overturning resistance for various structures including piers, bridges, power plant components and commercial buildings. These systems were ultimately used on the projects due to a combination of high uplift forces or overturning moments on the structures and the relatively poor subsurface conditions present at the sites. Other, foundation systems such as rock-socketed drilled shafts and spin fin piles were considered but were found to be economically prohibitive or not technically feasible.

Jan 1, 2011

By N. O. Lotter

The reliability of a set of flotation results is key to minimizing project risk, either at the commissioning of a concentrator or at the point of implementing an improvement to an existing concentrator operation. High-confidence flotation testing (HCFT) was developed for this purpose and is part of the list of technologies at various scales used by Xstrata Process Support (XPS) in addressing these projects. The methodology is based on two principles: one, to ensure that the ore sample is representative and has been well-blended and subsampled; two, to perform the flotation tests in sufficient numbers of replicates with appropriate quality controls, so as to improve the reproducibility of the test data. Across ten years of research on this methodology at Xstrata Process Support, Sudbury, several improvements to the HCFT method and complementary connections between sampling and quantitative mineralogy have been developed. Two case studies are reviewed. These show the capability of this system in both optimizing an existing concentrator operation and in serving a new mine scenario. Further work to improve the efficiency of this procedure has been identified. Key words: Flotation testing, Flotation

Jan 1, 2010

By N. O. Lotter

The reliability of a set of flotation results is key to minimizing project risk either at concentrator commissioning, or at the point of implementing an improvement to an existing concentrator operation. High-Confidence Flotation Testing was developed for this purpose, and is part of the list of technologies of various scales used by Xstrata Process Support (XPS) in addressing these projects. The methodology is based on two principles: one, to ensure that the ore sample is representative and has been well-blended and subsampled; two, to perform the flotation tests in sufficient numbers of replicates with appropriate quality controls, so as to improve the reproducibility of the test data. Across ten years of practice and continuous improvement with this methodology at Xstrata Process Support, Sudbury, several improvements to this method and complementary connections into sampling and quantitative mineralogy have been developed. Two case studies are reviewed. These show the capability of this system in both optimizing an existing concentrator operation and in serving a new mine scenario. Further work to improve the efficiency of this procedure has been identified.

Jan 1, 2009

By Che Xin, Liu Tianlong, Bi Hongyun, Chen Lijia

"High-cycle fatigue experiments were conducted at 800°C in laboratory air for three ferrite stainless steels including 15CrNbTi, 15CrMoNbTi and 18CrNbTi, where the stress ratio of 0.l was adopted. The experimental results show that at 800°C, the fatigue limit of the 15CrMoNbTi steel is the highest, the fatigue limit of the 15CrNbTi steel is slightly lower than that of the 15CrMoNbTi steel, and the fatigue limit of the 18CrNbTi steel is the lowest. At the same maximum stress, the 15CrMoNbTi steel has longer fatigue lives than the 15CrNbTi steel in the low stress area, while the 18CrNbTi steel has the shortest fatigue life. In addition, the observations on the fracture surfaces of fatigue specimens reveal that the fatigue cracks initiate transgranularly at the free surface of the specimens and propagate in a transgranular mode.IntroductionIn modem automotive industry, the manufacturers have paid great efforts to clean exhaust gas and to improve fuel economy. It is thought an effective way to increase the temperature of combustion chamber in automotive engine. And thus, the manifold closed to the engine in automotive exhaust system can suffer high temperature up to approximately 1000°C. Because of their relatively low thermal expansion coefficient, high yield strength at elevated temperature and good fatigue resistance, ferrite stainless steels, especially added with alloying elements such as Mo, Nb and Ti, are increasingly used for automotive exhaust systems [1-3]. In fact, exhaust manifold operated under high frequency vibration and exposed to high temperature exhausting gas also requires good fatigue resistance at elevated temperature. Some studies on the high temperature fatigue characteristics of stainless steel have been documented. It has beeen found that the fatigue limit of four ferrite stainless steels including 409L, 436L, 429EM and 444 (18Cr- 2Mo) reduces significantly with increasing temperature [4, 5]. In the research concerning the effect of a-phase embrittlement on fatigue behavior in a high-chromium ferrite stainless steel, it is noted that the precipitation of brittle a-phase will reduce the crack initiation and growth resistances and result in a decrease in fatigue limit [6]. In this investigation, the high-cycle fatigue behavior of three ferrite stainless steels including 18CrNbTi, 15CrNbTi and 15CrMoNbTi at 800°C have been studied to address the mechanical aspect of high-cycle fatigue behavior for ferrite stainless steels and to provide the theoretical reference for the safe design of automotive exhaust system."

Jan 1, 2013

By A Dal-Corobbo

Traditional acid and metalliferous drainage (AMD) wastewater treatment focuses on the iron co-precipitation/adsorption process as this is a very effective method of reducing heavy metals, including copper, lead, zinc, arsenic, etc, to parts per billion (ppb) levels in AMD wastewater streams. One of the drawbacks to this method however is the large volume of sludge produced and subsequent disposal costs for the mine site concerned.A proprietary metals treatment system called high density sludge (denoted HDS) which significantly reduces the quantity of waste generated is described in this paper. This process generates a dewatered sludge that contains in the order of 50 to 55 per cent solids. This sludge is denser than conventionally dewatered sludge, which typically contains only 20 to 30 per cent solids. This advanced process has a wide range of applications and can be easily retrofitted into existing AMD treatment systems. It has been successfully installed at several mine sites to treat AMD wastewaters. This paper discusses the high density sludge process, its benefits and provides data and operating results from pilot test installations.CITATION:Dal-Corobbo, A, 2013. High-density sludge process for treating metal bearing acid and metalliferous drainage wastewaters, in Proceedings Water in Mining 2013 , pp 217-220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Qing-hua Tian, Xue-yi Guo, Fei Li

A novel process for the preparation of a-Al2O3 from secondary aluminum dross was studied. Factors including alkali dross ratio, salt dross ratio, smelting temperature, smelting time, leaching temperature, leaching time, and the solid-liquid ratio, which possibly influence the transfer of Al into water were studied, and the feasibility of using seed precipitation as a treatment technology of the leachate was discussed. The optimum condition of the process was determined as: alkali dross ratio 1.3, salt dross ratio 0.7, smelting temperature 500°C, smelting time 60min, leaching temperature 60°C, leaching time 30min, solid-liquid ratio 1:4. The results show that using the seed precipitation method, the leaching of aluminum reaches 92.71%, demonstrating the technique as a feasible and effective treatment technology of the leachate.

Jan 1, 2011

By Thomas Oberndorfer

INTRODUCTION Since several years the author is engaged in research activities in the field of mining method modelling (Oberndorfer, 1993 and 1994). The initial goal was to improve and assist the selection of the most appropriate mining method. However during investigations it became obvious that the most beneficial application of computer support is the fast calculation of numerical assessment rather than the consideration of all, i.e. also qualitative, criterions necessary for final decision. Numerical results serve - together with qualitative considerations based on the experience of the mining engineer - as a basis for decision. The emphasis is on "fast" calculation, as only this property makes it possible to calculate and compare many distinct variations. As long as no procedure exists, which optimizes all involved parameters, calculating many variations is of great important, because it is the only way to increase the chance to pick a alternative "close to optimum", but also to learn about the sensitivity the result will react on changes of input parameters, which are rarely known exactly. Generally speaking many trials give a better basis for final decision. It is no secrete that the most important obstacle towards quick calculations of a series of alternatives is not the processing time of the computer, but the time required for setting the input data in way that the computer can start processing, which is usually inter- active man work on the screen. Furthermore usually several distinct programs are required to cover the whole range of involved problems, with corresponding problems in automatic data transfer. The research work's goal was to overcome these problems. The approach developed was to describe a mining method more in a theoretical way (i.e. to give the computer some degree of "consciousness" on mining methods), which then can be applied under any specific conditions. E.g. a cut-and-fill operation will be "generally" the same in narrow or thick deposit areas, but the resulting keyfigures, e.g. total tonnage, productivity, dilution and loss, or finally costs per ton, will differ significantly. The approach (MMM = mining method modelling) presented reflects a deduction from the general case to a specific one (rather than the other way round). The developed model is general enough to be applicable to any mining method, and also to any degree of precision the mining method should be described, contrary to programs designed for specific mining method layouts which can be adjusted in a more or less wide range. PROGRAM DEVELOPMENT The principle correctness and feasibility of the approach was proved by a prototype program. However this program was more on a research level and far away from application for "real world" problems. The reason for this was, that it was regarded wasted time to re-invent certain tools, e.g. geometry intersection, deposit modelling or visualization. Hence it was tried to attract several software producers to invest in finalizing the model. Unfortunately this endeavor was not successful. Despite this defeat - and after some months of resignation - a final start on the project was decided. he reason for this decision was not at last the research activity in respect of low-cost underground mining methods for bulk- material as a substitute of typical quarry operations due to environmental restriction. This research work - which is in particular important for Austrian mining activities in beautiful and touristically used landscape - requires a lot of calculations in the way described. Both are still in state of progress, but - regarding mining method modelling - preliminary results can be presented. A complete re-programming of the program was required. Most obvious are the changes of programming language and operating system environment. Instead of Pascal under DOS C++ under MS-WindowsNT is now used. Several problems could be solved by this, in particular memory management, device drivers for input/output, and user friendlyness by up-to-date windows technology. However also more basic structures were changed. The idea was to utilize as many existing commercially available programs as possible to minimize programming efforts. WindowsNT helps already a lot by MFC technology, but also due to its multi-task facilities. This feature allows to run simultaneously several pro-

Jan 1, 1996

By D. A. Dahlstrom

THE necessity for slime elimination from valuable mineral and coal products has become increasingly significant within the past 5 years.1,2 Most of the mechanized mining and present beneficiation methods have resulted in larger tonnages of extreme fines, silts, and clay, commonly called slimes, processed by the preparation plant. Economics in turn have forced the plant operator constantly to lower the bottom size of effective beneficiation, necessitating an almost complete recovery of valuable solids regardless of particle size. When these important factors are considered, the need for an efficient slime removal method for fine solids becomes self-evident. Ordinarily slimes have been classified as ranging from 75 microns, or 200 mesh, down to colloidal dimensions of less than one micron. At the same time there is general agreement that the most troublesome slimes are primarily clays, silts and extreme fines, so that the actual top size may be placed at approximately 30 to 40 microns. This immediately restricts any desliming operation to classification, as screening or other methods would be both uneconomical and grossly inefficient at such dimensions. The liquid-solid cyclone has been recognized as one of the most efficient fine size classifiers available to the mining industry. Applications of cyclones to thickening, high efficiency solid recovery, degritting,

Jan 1, 1952

By Chris J. Conway, Bruce W. Atkinson, Graeme J. Jameson

The flotation of coal in the fie and coarse particle size ranges presents particular problems. Fine or ultra-fine coal less than 100 microns presents a challenge to conventional flotation machines because the rate of capture of the coal particles can be very low, so longer residence times are needed. Also, conventional mechanical cells are not normally designed with froth properties in mind. Froth drainage may be inadequate, leading to excessive entrainment of ash. The upper limit of flotation of coal is normally put at about 500 um (30 mesh). It appears that, in mechanical cells, coarser particles tend to be torn away from bubbles in the turbulent environment created by the impeller. In this paper, results are presented from plant trials of a high-intensity flotation column of novel design, namely the Jameson cell. Extensive trials have been conducted on coal slurries with a top size of around 1 mm. Size-by size analysis shows that it is possible to achieve high yields of low ash product over the whole particle size range.

Jan 1, 1995

By David Hall

IN October, 1926, the Inspiration Consolidated Copper Co. began the operation of its new leaching plant, which has a capacity to handle 8600 dry tons of ore daily and produce therefrom approximately 160,000 lb. of electrolytic copper per day. (See Fig. 1.) The energy for the leaching process is supplied by three motor generator sets (Fig. 2), each set consisting of one 5450-hp., 6600-volt, three FIG. 1.-LEACHING PLANT OF INSPIRATION CONSOLIDATED COPPER CO. AT INSPIRATION, Ariz. phase, 25-cycle, 500-r.p.m. synchronous motor and two 1920-kw., 150 to 320-volt, 6000-amp.,12-pole, d. c. generators, and one 70-kw., 125-volt d, c. exciter. The capacity of the three sets is 36,000 amp. at 320 volts. A description of the metallurgical processes of this plant was. given in a paper by H. W. Aldrich,1 and from his paper we quote the following figures for the month of July, 1927:

Jan 1, 1928

By Richard Cole

The Energy Act of 1992 has many users of ac-induction motors eyeing premium-efficiency motors with mixed feelings and perhaps some confusion. When the October 1997deadline arrives for compliance with the1992 standards, the winners will be the environment due to reduced need for more power generating plants and the petroleum economy because of reduced dependency on foreign oil. But what will it mean for industrial users? The most obvious benefit is the potential for smaller electricity bills. Motors account for about 64% of the electricity consumed in the United States, at a yearly cost of $112 billion. Every 1% reduction in motor demand cuts 0.64%, or $716 million, off the industry wide bill. Higher efficiency motors also run cooler. This lightens the load on air-conditioning systems and further reduces plant demand. Lower total demand can lead to lower rates by helping to minimize peak-demand surcharges. As rates increase over time, these savings get bigger.

Jan 1, 1996

By T. Lezhava

A new reactor model with rotating cathodes has been developed where various forms (dendrite, spongy) of metal depositions and their uninterrupted removal are accomplished by the realization of high current densities and low energy consumption. At the same time in contrast with the existing methods a high quality metal powder may be obtained from concentrated electrolytes without any specific organic or inorganic additives, which allows raising the intensity of the process. The reactor can be used for electrowinning of metals with low adhesive capacity (Pb, Ag, Cu, Zn, Ni, Co, etc.) and the powders. The obtained products may be utilized in general metallurgy as well as in powder metallurgy.

Jan 1, 2006

By E. E. Bauer

Oversize boulders in mines and quarries must be broken for waste disposal or further processing of ore. Early methods involved drilling and "shooting" or using a drop ball of sufficient weight to accomplish the purpose. The first "high-energy" hammers for breaking concrete or boulders were pneumatically operated. Blow energy was limited by valving and air pressure. However, smaller boulders of lower compressive strength could be broken. A hydraulic excavator-backhoe type machine was required for either a drop ball or hammer. Standard practice was to break oversize boulders in the pit before hauling to the grizzly or crusher. Generally, quarry boulders were not valuable enough for further processing. Quarry roads were lined with oversize boulders. As safety requirements were advanced, "drill and blast" for boulders was ruled out.

Jan 1, 1994

By Ivor Hawkes

INTRODUCTION High energy breaking is an alternative to using ex¬plosives in underground secondary breaking operations. It also is a means of upgrading conventional hand-held breakers, manual sledge-hammer breaking, and scaling bar operations. Major areas of application are in sec¬ondary breaking over grizzlies and at drawpoints. Other applications include breaking down ripping lips in longwall seam mining, scaling in stopes and rooms, general demolition work, and roadway maintenance. There is considerable interest in high-energy impact breakers for use in primary ore breaking, but, as of 1977, all such applications have been only experimental (duToit, 1973; Joughin, 1976; Wayment and Grantmyre, 1976). EQUIPMENT Essentially, a high-energy impact hammer is a boom¬mounted pneumatically or hydraulically actuated breaker. The machine basically consists of a piston that oscillates in a housing and impacts the end of a tool or moil thrust against the rock. The force applied to the rock primarily depends upon the impact energy of the piston-the higher the impact or blow energy, the greater the force and, thus, the greater the rock break¬age. Among drill and breaker designers, a common expression for blow energy is "force of blow." Hand-held breakers are limited to blow energies of about 140 J (100 ft-lb), because the operator is unable to handle heavier machines efficiently or to absorb the recoil energy resulting from higher blow energies. How¬ever, these restrictions do not apply to boom mounted breakers; machines with blow energies on the order of 4000 J (3000 ft-lb) and higher are available commer¬cially for underground use. There is considerable evi¬dence to show that increasing the blow energy also in¬creases the efficiency of the breaking operation; i.e., more rock is broken per unit of energy expended (Grantmyre and Hawkes, 1975). Thus, there is a trend to higher blow-energy machines, particularly where high¬strength rocks are to be broken. In relation to rock breaking, the blow rate of boom¬mounted impact breakers is not as important as it is for rock drills. This is because the breaker must be moved over the work surface between blows. The blow rate is governed eventually by the power supply, and typical blow rates range between 200 and 600 blows per minute. As a general rule, light blow-energy machines have higher blow rates than heavier machines. Table 1 lists most of the boom-mounted impact breakers that were available commercially during 1977, and it gives details of the blow energies and machine weights. Restrictions are placed on the blow energy by the machine weight and size, and by the strength of the boom. Typically, boom-mounted impact hammers have a blow-energy to mass ratio of about 1.5, with lower values for lighter machines and higher values for heavier machines. In addition to supporting the hammer weight, the boom also has to absorb the recoil energy of the blow, which can be on the order of 1400 J (1000 ft-lb) for large hammers operating in a horizontal mode. Interesting exceptions to the general run of impactors are the Joy HEFTI hydraulic hammers. In these machines, the piston impacts onto a fluid cushion that is positioned between the piston and the impact tool. This approach allows very high piston velocities, over 30 m/s (100 fps), to be used without the risk of break¬ing the piston or impact tool. Steel on steel impacts must be limited to impact velocities of about 10 m/s (35 fps) due to the high impact stresses generated; thus, increased blow energies can be achieved only by increas¬ing the piston size. The Joy 514 HEFTI®, listed in Table 1, has a blow energy of 27 100 J (20,000 ft-lb), but, as of 1977, the machine has been used underground only on an experimental basis. Using a fluid cushion between the piston and the impact tool allows the use of light pistons, reducing the overall machine weight. The recoil energy, which must be absorbed by the boom for a given blow energy, is directly proportional to the piston to machine mass ratio, and operating with light pistons provides an addi¬tional benefit in reducing the requisite boom size. Both pneumatic and hydraulic hammers are avail¬able commercially. Although hydraulic hammers are a relatively recent development, they already outnumber the pneumatic machines in use. There are many reasons

Jan 1, 1982

By Marie-Josée Banwell, Cyriac Sebastian, Giacomo Falorni, Sara Del Conte

Interferometric Synthetic Aperture Radar (InSAR) is a satellite-based monitoring technique that complements other in-situ methods for detecting and measuring surface displacement. Recent advances in data processing algorithms, coupled with the use of high-resolution satellite systems, make it possible to now provide high-frequency InSAR monitoring services, with updated results delivered every time a new satellite image is acquired. The advent of large, continuously updated data sets, however, brings new challenges, including the need to rapidly sift through the data to identify only those points showing relevant ground displacement information. This has been achieved by using trend variation analysis tools, that quickly isolate and highlight only areas of anomalous behavior. The paper focuses on project case studies where continuous InSAR monitoring has proven to be key in identifying displacement trend changes near tunnel alignments.

Jun 13, 2021

By Henrique D. G. Turrer, Robert F. Winterfield, Jobe E. Wheeler, Marcello R. Cru, Baojie Zhang, Pedro P. Pinto

Efficient particle classification is essential to enhance gravity and magnetic separation stages in one iron ore beneficiation plant. This study investigates the use of high-frequency screens to process finely ground iron ore, focusing on two size cuts: 400 μm and 100 μm. Pilot-scale trials were performed on four ore blends using a full-scale screening unit. A total of 48 tests were conducted, evaluating the effects of panel aperture, solids concentration, wash water, and feed particle size distribution. Results showed that wash water improved efficiency by up to 5%, while a solids concentration near 40% w/w delivered high separation performance with minimal ultra-fines in oversize streams. Apertures slightly larger than the target cut sizes yielded better precision in particle separation. Feed particle size distribution had limited impact on efficiency. The investigation successfully identified optimal screening conditions, including aperture selection, to achieve the most effective separation performance for downstream concentration processes.

Feb 22, 2026