Search Documents

By Qingyu Deng, Shiwei Ma, Wang Hua, Guibao Qiu

"The flow properties of the blast furnace slag bearing high TiO2 at high temperature like the viscocity may change a lot due to the formation of the carbonitride inside, causing serious problems on the separation between the metal and the slag. Therefore, the critical condition of the formation of Ti(C,N) in blast furnace is vital importance for the ironmaking process with iron ore bearing titania. In this study, the formation of Ti(C,N) in blast furnace and the influences of various factors on the Ti(C,N) formation are investigated by FactSage. It is found that the mass of Ti(C,N) would reach the maximum at 1480 oC, and the product is mainly TiN below 1620 oC, while it is mainly TiC above 1620oC. The order of the factors by the importance from strong to weak was: temperature, the content of TiO2 in slag, basicity of slag, the content of MgO and Al2O3.IntroductionThe titanium dioxide (TiO2) in iron ore bearing titania will be partly reduced by carbon to titanium carbonitride (Ti(C,N)) in blast furnace, causing serious problems on the separation between the metal and the slag because of the change of flow property. Therefore, the critical condition of the formation of Ti(C,N) in blast furnace is vital importance for the ironmaking process, especially for the smelting of iron ore bearing titania. Extensive experimental data in regard to the formation of Ti(C,N) has been reported in numerous papers[1-6]. However, only some discrete data can be obtained by experiment, and it is difficult to detect the mass of Ti(C,N) in slag. In addition, the experiment is difficult to be proceeded when the temperature is above 1600oC. Therefore, it is very difficult to make clear the critical condition of the formation of Ti(C,N) by experiment."

Jan 1, 2012

By H. Krogerus, P. Niemelä, P. Oikarinen

High carbon ferrochromium is produced by carbon reduction. No replacement for carbon as reductant has yet been developed. The reduction creates a considerable amount of CO-gas. In open and semi-closed furnaces the gas is burned when leaving the burden. In closed furnaces the formed gas is sucked out by a fan, washed and utilised as fuel. The formation of carbon monoxide is presented briefly starting from thermodynamic considerations up to solid and liquid state reduction. The volume, composition and energy content of the furnace gas are discussed, focusing on the raw materials and pre-treatment processes of the furnace feed as well as on the process equipment and control. Outokumpu has been using closed and sealed furnaces and utilising the CO-gas in its Tornio Ferrochrome Works since 1968. Today in Tornio with an annual ferrochromium production of 260 000 t CO-gas production is 186 million m3, representing 68 MWh an hour. At the same time the furnace power input is 95MW. About 98 % of the CO-gas is utilised, whereof 30% in the ferrochrome production itself. This paper focuses on the characteristics and utilisation of CO-gas. CO-gas is secondary energy, which on one hand saves primary electric and fossil fuel energy in ferrochromium production and, on the other, replaces other fossil fuels at the adjacent steel works. The characteristics of the fuel, requirements for utilisation as well as health and safety aspects are discussed. Utilisation of the gas has a high impact on the total dust and gaseous emissions and on the energy optimisation at the ferrochromium and steel works.

Jan 1, 2004

By Carlos Eduardo Pinedo

A nitretação dos aços inoxidáveis tem sido objeto de diversos estudos nas últimas décadas. O objetivo primordial é promover o endurecimento superficial e com isso elevar a resistência ao desgaste, sem comprometer a resistência à corrosão. Em vista disto, a nitretação sob plasma a baixa temperatura, abaixo de 430oC, tem se mostrado um processo eficiente para inibir a precipitação de nitretos de cromo e promover o endurecimento superficial pela formação de fases expandidas pela supersaturação de nitrogênio. Este trabalho mostra a formação de ferrita expandida em um aço inoxidável ferrítico. Para isso foi utilizada o processo de nitretação sob Plasma-DC na temperatura de 400oC por 20 horas em mistura gasosa contendo 75%N2 e 25%H2. Os resultados de Difração de Raios-X mostraram que a nitretação em baixa temperatura é capaz de formar uma camada nitretada de ferrita expandida. Em Microscopia óptica observa-se uma camada homogênea com profundidade média de 32 microns de profundidade e dureza média de 1296 HV promovendo um endurecimento superficial do aço inoxidável ferrítico em mais de 5 vezes sem que ocorra a precipitação de nitretos de cromo e, com isso, preservado a resistência à corrosão.

Oct 30, 2017

By Gabriela Pereira de Miranda

Os aços avançados de alta resistência do tipo dual phase (DP) são aplicados na indústria automobilística, principalmente, em componentes estruturais. Alguns desses aços são revestidos com zinco e suas ligas, visando maior resistência à corrosão. Atualmente, o processo de união de aços mais utilizado em veículos é a soldagem por pontos. O emprego inadequado de parâmetros de soldagem pode provocar trincas por fragilização por metal líquido (LME, do inglês liquid metal embrittlement) em regiões de soldas a pontos de aços de alta resistência revestidos com zinco. O metal líquido, neste caso, consiste em ligas de Zn-Cu provenientes da combinação de cobre dos eletrodos de soldagem com o zinco do revestimento, que penetra em contornos de grãos, reduzindo a sua energia coesiva. Sob solicitação mecânica, tal fragilização pode ocasionar origem às trincas. Neste trabalho foram investigadas as condições de formação de trincas por LME na soldagem de aços DP da classe de 600 MPa de limite de resistência galvanizado por imersão a quente (HDG - GI). Verificou-se, em todas as condições de soldagem avaliadas, a penetração do metal líquido na superfície da solda. A ocorrência de trincas, no entanto, só foi constatada em condições de soldagem que implicaram na geração de tensões. Tais tensões foram intensificadas com refrigeração inadequada, causada por diferentes vazões de água nos eletrodos inferior (1,5 l/min) e superior (7,5 l/min), e/ou soldagem sequencial. Não foram observados efeitos prejudiciais de trincas por LME nas resistências estática (cisalhamento por tração) e dinâmica (fadiga sob cisalhamento).

Oct 30, 2017

The paper provides an overview of the development and content of APCOM symposia since their inception in 1961. This development is set within the context of the academic environment in which much of the research published at APCOM symposia is conducted. This environment includes rigorous external assessment of research quality at national levels and against international benchmarks, which carries significant consequences for funding and for the continued existence of the academic minerals industry disciplines. Adverse consequences that undermine the academic provision of mining and resource engineering will impact negatively on the minerals industry by reducing the level of research and education resources available to it.The traditional reductionist approach to research is contrasted with the inter-disciplinary approach that is required to address the complex systems problems that the minerals industry will have to address to ensure its technical, economical and environmental sustainability. Such an approach offers a means of raising research profiles, of establishing mutually beneficial academic-industry engagement and provides an opportunity for APCOM to take a lead role in identifying the research and development agenda for the future

Sep 26, 2011

By Norman O. Lotter, Dominic Fragomeni, Jorge Oliveira, Dee J. Bradshaw, Rebecca Monnapula

"The role of mixed collectors in enhancing the metallurgical performance of sulphide flotation processes was reviewed in 2008, and later published as an integrated theory by Lotter and Bradshaw, 2009. The theory proposed that xanthates, dithiophosphates and dithiocarbamates could be synergistically combined in an optimal formula to deliver improved grade and recovery. The approach uses a five-step structure, viz.1. A mineralogical study of the ore to be treated, identifying and quantifying the economic minerals (with hosting and association) and gangue species present.2. Selection of candidate collectors from this mineralogical information and from the known pulp conditions of that operation (e.g. Eh, pH).3. Design and execution of a factorial experiment to estimate and test the main effects and interactions, and to model the response surface for an optimum formulation [Box et al., 1978].4. Use of a High-Confidence Flotation Test platform in the factorial to reduce overall errors and allow for clearer observations [Lotter, 1995; Lotter and Fragomeni, 2010].5. Statistical design of a plant scale trial to measure and validate the gains [Napier-Munn, 1995; Lotter et al., 2009]. Eland Platinum, which was commissioned in November 2007, appointed a team to apply this theory to formulate an optimized mixed collector suite for use in the operation. The West Pit ore (UG2 - Normal ore) was sampled at site and brought to Xstrata Process Support, Sudbury, Canada, for mineralogical and metallurgical testing in 2008. Microprobe and QEMSCAN measurement characterized the type, grain size and textural association of the discrete Platinum Group Minerals (PGM) present. From the mineralogical data, it was clear that a mixture of dithiocarbamate and two xanthates would be a likely reagent suite selection. A factorially designed set of High-Confidence Flotation Tests studying these was performed, concluding that an optimal suite using certain amounts of these collectors was a viable formulation that would advance the grade and recovery performance at Eland above the standard PIBX by approximately 2.13% 4E PGE. The plant trial, which used a form of the replicated block design after Napier-Munn, 1995, and Lotter et al., 2009, exceeded this estimate with an overall PGE recovery gain of 2.48% (absolute basis) and a concentrate grade gain of 26.4 g/t PGE (absolute basis), as well as reducing chrome in concentrate from 2.04 to 1.62% (absolute basis). These gains proved to be statistically significant using the analysis of variance method, and have validated the theory."

Jan 1, 2011

By M. K. Kim

This study presents a framework for quality inspection of precast concrete components using the 3D laser scanning technique. As precast concrete-based rapid bridge construction is getting standardized, quality assessment of the precast concrete becomes critical for preventing any failures during the construction process. Moreover, as Building Information Modeling (BIM) gains popularity in the construction industry, autonomous and intelligent inspection systems are needed. Current method for quality control of precast concrete components, however, heavily relies on visual inspection and contacttype measurements, which are time and labor demanding. Also, storage and delivery systems of inspection information such as the procedures and results of quality inspection are lacking. To overcome these limitations of the current quality assessment technique for precast concrete, this study aims to develop a BIM-based framework for efficient quality inspection of precast concrete with the use of a 3D laser scanner. First, we formulate practical guidelines including detailed inspection procedure, selection of optimized scanner and scan location, inspection criteria, and data storage and delivery system. Second, to investigate the applicability of 3D laser scanning to precast concrete quality inspection based on the proposed framework, a case study inspecting quality of a lab-scale object assumed as precast concrete component is presented for detecting defects.

Aug 1, 2013

By Letícia Miranda Alves

Os pós fluxantes têm como base o sistema CaO-SiO2-Al2O3-Na2O-CaF2 sendo que, em alguns casos, podem conter também MgO, Li2O, K2O e B2O3. Os resíduos de mármore e granito, oriundos dos processos de produção de rochas ornamentais, são passivos ambientais na região sudeste, sobretudo no estado do Espírito Santo. As composições destes resíduos são similares a dos pós fluxantes utilizados nos processos de lingotamento contínuo e portanto serão utilizados neste trabalho para formulação de novos fluxantes. Uma mistura de granito, pó de mármore e adições foi realizada com o objetivo de produzir um fluxante similar aos comerciais encontrados no mercado. O novo fluxante foi caracterizado por difração de Raios X antes e depois de passar pelo teste de susceptibilidade de formação de fases cristalinas ou “teste de Stollberg” modificado. Os resultados mostraram que existe a formação de fases similares às observadas em fluxantes comerciais. Avanços nesta área podem viabilizar economia de matéria-prima e a diminuição do impacto ambiental causado pelo mercado de rochas.

Aug 17, 2017

By Rainer Antretter

The city of Garmisch-Partenkirchen in southern Germany is located at a main transit road to Tyrol in Austria and suffers of a very heavy traffic load. Therefore, the Kramertunnel as a by-pass tunnel is built to release/mitigate the traffic through the city centre. The 3,600 m long single tube road tunnel is designed with a parallel but smaller emergency tunnel and with cross passages, fitted with single- and doublesided emergency bays, a vent shaft, and an intermediate ceiling to separate fresh air supply from the road traffic. The tunnel, concrete lined along its entire length provided the challenge to find smart formwork solutions for quick set-up, repositioning, setup and pouring. Three particularly specific sections are discussed in this paper.

Jun 13, 2023

By Tiago Ribeiro Costa

A Praxair é uma das três maiores empresas de gases industriais do mundo, com atuação em mais de 40 países e fortemente atuante na indústria siderúrgica. A Praxair possui experiência para fornecer produtos e serviços para todos os tipos de siderúrgica. Diversas tecnologias desenvolvidas pela Empresa, como o CoJet® (sistema para injeção de jato coerente de oxigênio em fornos elétricos e conversores), Slag Splashing (espalhamento de escória nas paredes de conversores, aumentando a vida útil dos refratários), AOD (processo para produção de aços especiais) e outros, encontram-se em operação comercial atualmente em diferentes partes do mundo. No Brasil, a PRAXAIR é a controladora da White Martins, maior empresa de gases industriais da América do Sul, presente em nove países do continente. Seu portfólio inclui gases atmosféricos, produção de gás carbônico, acetileno, hidrogênio, gases especiais e medicinais, misturas para soldagem, cilindros de aço sem costura, equipamentos para aplicação, transporte e armazenamento de gases. A empresa também opera uma unidade para liquefação de gás natural. Além de tecnologias e processos, a White Martins também pode fornecer soluções e equipamentos para medição, controle e injeção de gases, atendendo às rígidas normas de segurança e padrões de qualidade. O Objetivo deste trabalho é apresentar e discutir sobre a solução para o fornecimento de mistura para atmosfera de fornos de tratamento térmico através de um painel misturador de gases hidrogênio e nitrogênio. Será discutida a operação do equipamento e abordadas às características construtivas.

Jul 31, 2018

By G. J. Hartman

A presentation of this project was given previously at the SHE Annual Meeting, Denver Colorado February 23-27, 1987. The project concerns the development of in situ recovery of borate products from a deep-seated colemanite deposit in California. The deposit contains some 147 million tons of borate ore containing 6.4% boron oxide (B2O3). This paper involves the numerous changes in the process that has taken place since that first presentation. This paper further explains the reasons for these changes which are primarily environmentally based and secondarily capital requirements related.

Jan 1, 1994

Organization Place Date 1918 National Society of Naval Architects New York, N. Y. Nov. 14-15 American Society of Mechanical Engineers New York, N. Y. Dec. 3-6 Geological Society of America Boston, Mass. Dec. 28-31 American Association for the Advancement of Science Boston, Mass. Dec. 27¬ Jan. 2. 1919 American Society of Civil Engineers New York, N. Y. Jan. 15-16 American Wood Preservers Association St. Louis, Mo. Jan. 28-30 American Society of Heating and Ventilating Engi¬ neers New York, N. Y. Jan. 28-30

Jan 11, 1918

Organization Place Date 1919 American Society of Mechanical Engineers... New York, N. Y. Dec. 2-5 American Institute of Chemical Engineers.... Savannah, Ga. Dec. 3-6 Geological Society of America..: Boston, Mass. Dec. 29-31 American Society of Heating and Ventilating 1920 Engineers New York, N. Y. Jan. Mining and Metallurgical Society of America.. New York, N. Y. Jan. 13 American Institute of Min. and Met. Engineers New York, N. Y. Feb. 16-19 American Ceramic Society Philadelphia, Pa. Feb. 23-26 American Electrochemical Society Boston, Mass. Apr. 8-10* *On Apr. 9, a joint meeting will he held with the A. I. E. E.

Jan 12, 1919

Organization Place Date International Mining Convention (Auspices, Van- 1919 couver Chamber of Mines) Vancouver, B. C. Jan. 8-10 American Institute of Consulting Engineers, Inc... New York, N. Y. Jan. 13 American Society of Civil Engineers New York, N. Y. Jan. 15-16 Institute of Chemical Engineers Chicago, 111. Jan. 15-18 American Wood Preservers Association St. Louis, Mo. Jan. 28-30 American Society of Heating and Ventilating Engineers New York, N. Y. Jan. 28-30 Automotive Engineers New York, N. Y. Feb. 4-6

Jan 1, 1919

Organization Place Date 1913 Mining and Metallurgical Society of America New York, N. Y. Jan. 8 American Institute of Electrical Engineers New York, N. Y. Jan. 11 American Society of Civil Engineers New York, N. Y. Jan. 22-25 American Society of Heating and Ventilating Engineers : New York, N. Y. Jan. 22-25 American Institute of Mining Engineers New York, N. Y. Feb. 18-21 National Society for Promotion of Industrial Educa- tion New York, N. Y. Feb.. American Institute of Architects Washington, D. C. April American Iron and Steel Institute New York, N. Y. May New York Electrical Society New York, N. Y. June National Association of Stationary Engineers Cincinnati, 0. Sept. American Chemical Society Cleveland, 0. Sept.

Jan 1, 1918

Organization Place Date 1919 National Drainage Congress St. Louis, Mo. Nov. 11-13 American Mining Congress St. Louis, Mo. Nov. 1.7-21 Canadian Mining Institute Vancouver, B. C. Nov.. 26-28 American Society of Mechanical Engineers:.... New York, N. Y. Dec. 2-5 American Institute of Chemical Engineers Savannah, Ga. Dec. 3-6 Geological Society of America...; Boston, Mass. Dec. 29-31. American Society of Heating and Ventilating 1920 Engineers New York, N. Y. Jan. Mining and Metallurgical Society of America ... New York, N. Y. Jan. 13. American Institute of Min. and Met. Engineers... New York, N. Y. Feb. 16-19 American Ceramic Society Philadelphia, Pa. Feb. 23-26

Jan 11, 1919

By Timothy J. Matthews, Timothy J. Batchler, Daniel J. McElhinney

The National Institute for Occupational Safety and Health’s (NIOSH) Mine Roof Simulator (MRS) at the Pittsburgh Mining Research Division was commissioned for operation in 1981. The MRS was originally designed for longwall shield research and was the only hydraulic press in the world with the capability to apply biaxial loads to these large structures. The results of this forty-year research program have contributed to improved performance and increased knowledge of longwall shields, mobile roof supports and hydraulic cylinders in the mining industry. Also, considerable research and development have been conducted to develop standing support technologies for the mining industry. The Support Technology Optimization Program (STOP) was developed to evaluate how these various technologies can impact and improve both ground control conditions and mine safety. Additional MRS research has included the performance of ventilation stopping walls including the development of a new testing protocol to evaluate the transverse loading capabilities under arching load conditions and evaluating the performance characteristics of welded wire screen as used in underground mine roof surface control. The NIOSH Mine Roof Simulator has been a reliable and valuable tool for the past forty years for the evaluation of safety structures used in mining, and this research has contributed significantly to the advancement toward safer mines. This paper will summarize those research results and provide a glimpse of planned future activities.

By J. M. Hemstock, H. L. Ames

THESE forums have been held annually since they were introduced by Mr. L. E. Djingheuzian in 1957. The response of millmen to questionnaires such as the one this year is ample evidence of the interest these create. This year's topic is unlike those of past years since it is an attempt to understand a new concept of grinding rather than to improve the old. Before, we were thinking in terms of 2-5 cents improvement in grinding costs, now we will be discussing savings of 15-2 5 cents. As a background for this forum we will begin by summarizing the major controversial issues relating to grinding with steel, many of which will undoubtedly apply to pebble milling. Our •task to-day is to learn what has already been done in pebble milling and obtain a fair overall view of this method of grinding.

Jan 1, 1961

By W. H. Zieman

"THIS IS THE THIRD of the consecutive Annual Forums on Grinding that were instituted by Mr. L. E. Djingheuzian in 1957. The first was on the subject of Ball Milling (Transactions, Volume LX, 1957) and the second on The N on-Cataracting Ball Mill (Trans-actions, Volume LXI, 1958). From the discussions at these forums it was evident that one of the most important factors affecting the efficiency of grinding is the shape of the liners. In order to make a study of liners in use, it was •decided to seek the co-operation of operators across the country by sending out questionnaires requesting basic information. Additionally, these operators were urged to set down briefly any pertinent information on the subject acquired through experience and experiments at their own particular plants. A compilation and analysis of these data were to form a basis for discussion at the Forum on Liners at the Annual Meeting in Montreal, April, 1959. The response of the milling fraternity to this solicitation was most gratifying, and clearly indicated the importance attached by the operators to the effect of liner design upon overall grinding performance."

Jan 1, 1959

By ALFRED T. BARR

In certain areas of the New Cornelia pit, considerable secondary blasting is necessary to reduce oversized boulders, formed from primary blasting, to pieces which will pass the 41/2-cu yd dippers on the shovels. Some of the boulders are 'dobied, but when time permits they are blockholed and blasted. In most instances one hole drilled to a depth of 2 to 3 ft and blasted with 1/3 to 1/2 of a stick of powder will break a boulder satisfactorily. Blockholing is normally done by using a jackhammer of the 55-lb class, 1-in. round drill steel, and detachable steel bits, 2-in. gauge when new. A bit change is usually made after the completion of each hole. The use of light drilling equipment in blockholing is desirable, both from the standpoint of safety and ease of doing the work, and when it was seen there was a possibility of using a lighter jackhammer through the use of tungsten-carbide bits and at the same time get at least the same drilling efficiency as with the standard equipment, it was decided to test tungsten-carbide bits. The claims for long life of the bits and footage drilled before resharpening gave hopes of eliminating much of the delay time in changing bits which is unavoidable with the use of steel bits. and thus gain in actual drilling time.

Jan 1, 1949