Search Documents

By P. H. G., Durville

ANY metal which contains even a small percentage of aluminum possesses certain peculiarities of appearance and properties which are exhibited both when the metal is melted and after it solidifies. Pure aluminum, or an alloy containing a small proportion of aluminum, can be melted without flux-except for a layer of charcoal-because a film of aluminum oxide and metal forms at the surface of melted aluminum. Although very thin, this film is air-proof, and it prevents the metal underneath from oxidizing. This oxidized film does not move easily on account of its toughness and high surface tension. One very important point in connection with this process of still casting has not been strongly enough stressed, namely, that the same kind of surface film with the same peculiarities forms over the surface of all melted alloys that contain even a small proportion of aluminum. Experienced foundrymen know how desirable it is to cast aluminum under its "skin" or under the surface of the film which tends to remain still. In the case of red copper, when in fusion, the surface shows pure copper only. This' is due to the fact that liquid copper constantly absorbs the copper oxide which forms on the surface. By closely examining melting copper the oxide can be seen dissolving in the bath, and going into solution just as pulverized sugar dissolves in water. When copper is cast in the open, either in wire bars or cakes, the surface of metal exposed to the air is covered by a film of black oxide that cannot be absorbed by the metal.

Jan 1, 1927

By Andersson PO

Boliden Mineral AB Boliden Mineral AB operates nine mines in Northern and Central Sweden, producing zinc, lead and silver concentrates and copper and gold. Seven of these mines use cut and fill (C&F) mining with a total production of 2 Mtonnes of ore per year.

Jan 1, 1998

In Australia we usually define "resource" in purely material terms, and rarely relate it to intellect and human capacity. We look at the sheer abundance of our natural resources and are satisfied with the feeling that we don't really need-to rely on using our brains. Certainly our country is fortunate to have the mineral resources it does, but in many ways Australia's worst enemy is its "lucky country" syndrome because we tend to underutilise the great resource we have in the capacities of our people. Raw material exports will undoubtedly continue to contribute a major share of our export revenue, but to harness the riches our country has to offer most effectively we need the vision and planning necessary to bring together our material and human resources. There is a need not only to find, exploit and process our minerals economically, but to turn as much of our mineral wealth as possible into high value products before it leaves the country. In particular we must use our brainpower if we want to maximise economic benefit from and political influence over the strategic minerals which leave our shores. In the past we have been successful in finding and exploiting minerals because our mining industry has been in the forefront of private sector research and development. But if Australia is to have an advantage over other mineral rich countries in insulating itself from the effects of cyclical swings in commodity prices, then the future of the industry must lie even more in technological sophistication rather than depending. on such considerations as size and location of mineral deposits. To survive, our mineral industry must have the foresight and resourcefulness to make its own luck. There are two keys to increased efficiency in exploration and production and in further processing methods: enhancement of the skills of the workforce and continual improvement of R&D.

Jan 1, 1986

By Gregg J. Hodges

The Stillwater Mining Co. is a partnership of The Pittsburg & Midway Coal Mining Co. and Manville Corp. The Stillwater Mine, located near Nye, MT, is the Western Hemisphere’s only primary platinum-palladium deposit. The mine began production of flotation concentrates in March 1987. In the fall of 1987, an integrated pilot plant testing campaign of electric furnace smelting and oxygen-blown converting confirmed the feasibility of further upgrading to semi-refined matte, or “white metal.” In the summer of 1990, the production smelter was brought on line. The record of the discovery and development of the Stillwater deposit, mine and concentrator has been summarized in several articles (White, 1987; Kennedy, 1987; and Hodges and Clifford, 1988). Similarly, the pilot campaign to test the feasibility of treating the flotation concentrates in an integrated smelting plant has been described (Hodges and Clifford, 1988; Matousek, et al., 1989; and Matousek and Whellock, 1990).

Jan 1, 1991

By D. J. Turk

Stillwater Mining Company’s, Nye Operation has been producing PGM concentrate since 1987.Several expansions have allowed for increasing capacity from the initial rate of 500 tons per day, to its present capacity of 3,000 tons per day. The expansions were performed with minimal impact upon production and maximum utilization of the existing equipment. The latest expansion incorporates a 6’ X 18’ SAG mill, 13’ X 20’ Ball mill, pebble crusher, rougher flotation cells, 1250 Hp tertiary grinding mill, middling and scavenger flotation cells, and cleaner column flotation cells. This paper will describe the concentrator flow sheet, and controls for improved concentrator performance.

Jan 1, 2000

By Gregg J. Hodges

The Stillwater pt-pd mine and flotation mill are located about 130 km (80 miles) southwest of Billings in Stillwater county, M6ntana~ The pt-pd ore zone stretches about 43 km (27 miles), but varies in thickness from 0 to 6 meters (0 to 20 feet, but generally 3-6 feet) and dips 55-90,degrees from horizontal. The ore is hosted in basic, layered igneous rocks containing about 1% sulfide minerals which include chalcopyrite, pentlandite, pyrrhotite, and minor pyrite. The pt-Pd minerals are intimately associated with these sulfide minerals and are found as precious metal sulfides, tellurides, bismuthnides, and arsenides as well as native Pt metal. Approximately 90 different precious metal minerals have been found, but about 80% of the pd is in solid solution in the pentlandite. The ore assays about 0.1% Cu, 0.1% Ni, 6.2 g Pt/tonne (0.18 Troy ounce Pt/short ton (opt)), 21.3 g Pd/tonne (0.62 opt Pd), 0.21 g Au/tonne (0.006 opt Au), and 0.21 g Rh/tonne (0.006 opt Rh). The ratio of pd to Pt in the Stillwater ore and concentrates is about 3.5.

Jan 1, 1988

By Harold G. Arthur

INTRODUCTION Stillwater Tunnel construction is scheduled to start in the spring of 1973. The tunnel will be the site of an extensive program in rapid excavation research. This paper presents a progress report regarding our plans and relates the tentative decisions which have been made on how to carry out the research effort. The details are subject to revision as more input is obtained from other Government agencies interested in tunnel construction and from experts in industry and educational institutions. The objective of the research program is to bring about faster, less costly tunnel construction. This objective will be pursued through the development, improvement, and evaluation of various construction systems and investigative techniques. The need for this kind of program was recognized by the National Research Council, in its authoritative report "Rapid Excavation - Significance, Needs, Opportunities." (1) The Council advocated a federally funded $200 million, 10-year program to help meet the $69 billion market it expects in underground excavation between 1970 and 1990. The significance of tunnel construction to Reclamation is made clear by statistics of its tunneling experience and outlook. Reclamation has constructed 174 water conveyance tunnels totaling over 190 miles, Six tunnels are presently under construction which have a combined length of about 27 miles. There are on the books nine authorized, but unfunded tunnel projects totaling another 70 miles in length. Many more miles of tunnels are included in programs in various stages of investigation.

Jan 1, 1997

Stillwater Mining Company (SMC) has an extensive history with tunnel boring machines (TBM) at the Stillwater and East Boulder underground PGM mines in Montana. The most recent TBM used is for the Blitz Project, where a 5.5m (18ft) diameter main beam unit, commissioned in Q3 2012, is being utilized to drive a 6,975m (22,500 ft) ventilation and haulage level East of the Stillwater Mine for the Blitz expansion project. The assembly/commissioning of the TBM, institution of the planned diamond drilling program, application of ground control systems, and the current tunneling metrics will be covered.

Feb 23, 2014

By R. St. C., G. E. Morris, M. Zbik, Smart

Effective flocculation and dewatering of slurry streams containing clays (particularly kaolin and smectites which are often <200nm in lateral dimension) is becoming increasingly urgent. Release of water (often >75 wt%), for recycle and reduced make-up water consumption, from slurries in tailings streams and dam beds is usually slow and incomplete. Changes in settling rates and solids density of tailings containing clays can be achieved in practice by changes in pH, dissolved cations and flocculant additions. To achieve fast separation of clays from water and minimization of retained water, individual particles need to be bound in the initial stages of thickening into large, high-density aggregates, which may sediment more rapidly with lower intra-aggregate water content. Quantitative STIMAN (STructural IMage ANalysis) cryo-SEM imaging, shows that the structure of aggregates formed before flocculant addition has a determinative effect on these outcomes. Without flocculant addition, 4 stages occur in the mechanism of primary dewatering of kaolinite: initially separate particles and aggregates are dispersed (<0.3GP, where GP is the gel point); a partially-gelled chain network then forms linking particles edge-edge (EE) still well below the OP but remains largely suspended; after an induction time, this network structure rearranges from EE to face-face (FF) contacts densifying, compacting and dewatering the aggregates with settling rates well above Stoke&apos;s Law estimates for >20µm particles or aggregates; the GP is rapidly reached during settling producing a network spanning the vessel with compressive strength. This sponge-like structure with EE oriented particles limits slurry dewatering because the steric effect in the resulting partially-gelled structure is much more dominant than the electrostatic effects predicted by DLVO theory. Van der Waal&apos;s forces at very close distances, as particles slide across each other, may be responsible for the EE to FF change in structure. In this way, the previously extended network contracts, and when the solid volume fraction is low, the continuous network breaks apart forming aggregates and aggregate associations as flocs which arc able to freely settle. These densified aggregates settle at increased rate, give lower bed density and retain less water after drainage. With flocculant addition, the internal structure and networking of the pre-aggregates is largely preserved but they are rapidly and effectively bound together by the bridging action of the flocculant(s). The STIMAN analysis shows that there is a inverse correlation of intra-aggregate porosity (and void permeability) with Darcian permeability (and extent of dewatering) whereas there is a strong positive correlation of Darcian inter-aggregate permeability with settling and primary dewatering rate.

Jan 1, 2004

By T. T. Read

FOR the second time the Mineral Industry Education Division opened the sessions at the Annual Meeting by gathering at the Engineering Woman&apos;s Club, Sunday at 3 p. in., and, in spite of the informality of the hour, with a good attendance of representative men in the educational field. The chairman of the Division, Thomas T. Read, after briefly reviewing some of the more significant events of the past year, introduced H. P. Hammond, professor of civil engineering, Brooklyn Polytechnic Institute, a leading figure in the project of the Engineers&apos; Council for Professional Development for accrediting engineering schools. Prof. Hammond made it clear that the project is not to rate engineering schools but to accredit them; not to arrange them in order of excellence, but to segregate them into two groups, those that are entitled to recognition as genuine engineering schools, and those that are not. About thirty schools in the whole country will presumably fall into the latter class; they are typified by an unnamed institution where the teacher of mathematics bears the title of Professor of Civil Engineering and the man who teaches chemistry that of Professor of Chemical Engineering, and having no engineering instruction except some elementary surveying, but still claiming in its catalogue to be an engineering college. While everyone would like to avoid the necessity of accrediting engineering colleges, it cannot be avoided, since the University of the State of New York, and several other agencies, are already doing it. If it cannot be avoided it is best that it should be done by a qualified agency set up by the national engineering societies, so that the results may command respect and general acceptance. It is for this reason, and this alone, that the accrediting committee of the E. C. P. D. has been set up. It is now ready to begin its task, and during-the coming year it will accredit the schools in two of the seven geographical districts into which the country has been divided, beginning with New England and the Mid-Atlantic States.

Jan 1, 1935

By K. Vanbroekhoven

An industrial site near the centre of a historical town in Flanders is characterized by chromium(VI) contamination of the groundwater. Since the potential for natural attenuation was not sufficient to control the groundwater plume as observed from different analyses like pH, Eh, soil oxidation and reduction capacity, the feasibility of site remediation based on in-situ bioprecipitation of chromium was examined in lab microcosm studies. By creating reducing conditions by addition of a carbon source in the groundwater, chromium(VI) can be biologically reduced to chromium(III), which can form an insoluble precipitate of chromium(III) hydroxide. Microcosms contained contaminated groundwater and aquifer samples that were collected and manipulated under anaerobic conditions. Three different carbon sources were screened for their effectiveness: molasses from sugar beet production, molasses form starch production (protamylasses) based on potato juice and lactate. The different concentrations of sugar molasses were used to determine the optimal conditions. A range of parameters was monitored at regular time intervals for a period of six months such as chromium(VI) and chromium(III), DOC, methane, pH, Eh. A rapid conversion of chromium(VI) to chromium(III) was observed for all conditions tested. However, extensive removal of chromium from the groundwater by precipitation was only achieved for a limited number of conditions. In general, lactate was found to be the most effective carbon source, slightly better than the lowest concentration of sugar molasses that was tested, which itself was more effective than molasses based on potato. Higher concentrations of molasses, although causing a steeper decline in redox potential, resulted in less effective Cr removal. Typically, the fermentation of molasses results in acidification and this drop in pH may hinder the formation of insoluble chromium(III)hydroxides. It may also be possible that certain components of the molasses form soluble complexes with chromium(III). For lactate, no significant drop in pH was observed. Following the laboratory microcosm tests, the stability of the chromium precipitates was examined by performing a sequential extraction on the microcosm materials. These were performed under redox conditions which were similar to the ones observed in the field. Since the outcome of these tests was positive, a pilot scale test was implemented in the field in April 2005. Two different substrates, the cheap waste product sugar molasses and lactate are being injected creating two different impact zones and typical parameters are monitored. Frequent re-injections were important to maintain reduced conditions and are carried out three-weekly up to now. To study the stability of precipitates formed, mesocosm socks containing aquifer material were installed in the monitoring wells and harvested at regular intervals. Results of this pilot test will be presented and compared to the laboratory results. Based on the success of this field test, a full scale process will be designed and implemented as remediation strategy.

Jan 1, 2006

By Anders Lagerkvist, Agne Rustan, Tommy Edeskar

Landfills containing house hold waste produces methane gas during its decomposition. This gas can be recovered and used for heating purposes or as fuel for vehicles. Gas drainage pipes are installed in the landfill and connected to a central suction point. Methane gas is produced over several years until the slots in the drainage pipes are clogged by black mud. And the bottom of the vertical drainage pipe are filled with mud and water. The hypothesis tested in this paper is if blasting in the drainage pipes could activate the production and flow of methane. In the first part of the paper we have studied what maximum linear charge concentration could be used in different size of PE-pipes place vertical on surface and surrounded by air. The results show that the maximum linear charge concentration for single blasts varied between 5-10 g/m, depending on the diameter of the pipe (90, 100 and 160 mm). Maximum charge concentration for the repeated blast varied between 2-5 g/m. In the second part of the paper we study what maximum linear charge concentration could be used in situ for full scale blasting tests in a special prepared test area which later on was dug out after the blastings. Up to 40 g/m could be used without damaging the top of the 160 mm diameter pipes. The increase in methane flow was so low so it could not be measured c4.5 m3/h. The conclusion therefore is that the stimulation of methane flow by explosives is not enough.

Jan 1, 2000

By J. Partyka

Fumes produced during blasting operations in underground mines are defined in this paper by an equivalent contaminant source. The primary goal is to establish a method which would allow all those parameters not measured directly to be determined reliably from field data. The parameters to be identified are the diffusion coefficient , and the position and size of an equivalent source. The diffusion-value is computed from the peak concentrations taken by two monitors located in the drift. The first monitor is placed close to where blasting pollutants join the main stream, while a second monitors is moved downstream a some distance from the first point. The position and size of the dust source and the total amount of dust produced during blasting are determined from the data recorded by only one monitor.

Jan 1, 1991

By M. Bozorgtabar

Metal Matrix Composites (MMC) have a ductile matrix containing ceramic particles, Due to their improved wear properties, Al?SiC composites have economical applications in many industrial uses where wear is a problem, One of the most serious difficulties in manufacturing Al-SiC composites is obtaining adequate &apos;wetting&apos; of the particles by the melt. In this research work, a stir casting system was designed for the improved manufacturing Al-SiC composites, The effect of some production variables such as the addition of SiC particles to the aluminum melt on wettability, was also studied. The results showed that the manual addition of particles would not be successful in manufacturing and that a system of adding silicon carbide particles through controlled temperature, atmosphere and improved mixing was needed.

Jan 1, 2005

By J. G. A. Stevenson

GENERAL Location of Property THE Stirling zinc-lead-copper deposit is in Richmond county, Cape Breton, about a quarter of a mile southwest from Stirling P.O., and some 45 miles southwest from Sydney. The property is accessible by road for at least nine months of the year, and during the navigation period coastal boats maintain a service touching at the port of Fourchu, eleven miles from the mine. When flying conditions permit, the Cape Breton Flying Club, of Sydney, will carry passengers to or from the property, a service which has been particularly advantageous on two occasions when hospitalization was urgently required. The Company has mining rights on leases Nos. 73-74, 78-80, and 101-104, inclusive, and owns 166 acres at Stirling and one acre at Fourchu. The ore deposit is in lease No. 73. History The Stirling deposit was discovered in the &apos;nineties&apos;, probably about 1895. The original discovery is said to have been made in the bed of Copper creek, which traverses the ore-zone. For a number of years, indifferent development work was carried on with a view to copper production only, and it was not until1915-16 that attention was directed to the possible production of zinc. Previously, the ore had been considered too complex for metallurgical treatment. During the period 1916-24 several operators attempted to develop the property, among them being the Stirling Exploration Company, Stirling Mining & Smelting Company, New Jersey Zinc Company of New York, Hayden & Stone Company of Boston, and The Eastern Mining & Milling Company. Up to 1924, the work was limited mainly to trenching, stripping, ? diamond drilling, and shot drilling.

Jan 1, 1937

By C. B. Ndimande, C. Ntsele, M. Lisso, L. Arlow

"In the processing of UG2 platinum ore, stirred milling technologies are dominating regrind applications that require grinding the particles to P80s’ in the region of 45 µm. For this application stirred mills are 30–40% more energy efficient and require a smaller foot print compared to traditional tumbling mills. In this work a study was carried out using a batch pin mill and three scales of Stirred Media Detritors. A laboratory scale pin mill, a pilot scale Stirred Media Detritor with an installed power of 18.5 KW and two industrial scale Stirred Media Detritors in continuous operation, with an installed power of 355 KW and 1,100 KW were used. The industrial scale SMDs were in the secondary grinding section of a mill floatmill float (MF2) UG2 processing plants. The tests were focused on assessing the effect of feed rate and percent solids on power consumption and product fineness at lab scale, floatation response of the SMD product at pilot scale and on an industrial scale, the effect of feed rate on energy consumption and product fineness. The measurements obtained were feed flow rates, mill power and from the samples cut, particle size distribution of both feed and product. Specific energy was observed to increase with increasing percent solids over the 30wt% to 80wt% studied. Floatation response tests of the pilot scale SMD products show improvement in grade. Specific energy and reduction rations are observed to decrease with an increase in feed rate.INTRODUCTIONThe purpose of comminution in most mineral processing applications is to liberate the valuable minerals from gangue so that they can be recovered in subsequent separation stages. Most precious and base metal plants treat low grade fine-grained ores which require a higher degree of size reduction to yield the necessary degree of liberation (Partyka & Yan, 2007). Many authors have shown that the relationship between product size and grinding energy consumption is exponential, the finer the product from the comminution device, the higher the energy consumption (Gao & Weller 1993; Napier-Munn, Morell, Morrison & Kojovic, 1996; Jankovic, Valery & La Rosa, 2003). The suggested reason for this kind of relationship is that smaller particles have fewer flaws and higher strength than larger particles. Particles with fewer flaws and higher strength require higher energy for breakage to occur. One of the challenges most plants face is that of efficient energy utilisation in the liberation of the mineral from these complex ores. Conventional tumbling mills are not energy efficient in fine and ultra-fine grinding applications because some of the energy is spent on moving the charge and does not go directly into breakage. Stirred mills have been found to be about 30% to 40% more efficient and require a smaller foot print compared to traditional tumbling mills for regrind applications that require product size with P80s’ in the sub 45 µm regions (Radziszewski & Allen, 2013). Stirred mills are able to produce fine product because they can achieve a high number of stress events per unit time and volume compared to tumbling mills (Kwade, 1999a). To minimise energy usage without compromising product quality, the mining industry has adopted stirred milling technologies for fine and ultra-fine grinding (Radziszewski & Allen 2014; Kwade, 1999b). The south Africa platinum group metal (PGM) industry alone had over 40 stirred media mills installed by 2011 (Rule, 2011). Of that 40, 13 were in the ultra-fine grinding (UFG) application and the rest in main stream inert grinding (MIG)."

Jan 1, 2016

By Chris Rule

This paper tells the story of the rapid commercial application of stirred milling technology at Anglo American Platinum?s many Concentrators. The first stirred mill ? a 10 000 litre IsaMillTM; the largest at the time, was commissioned in late 2003. The project development work was presented at SAG 2001. This operation was ?proof of concept? and vindicated the decision to scale up the technology; allowing a rapid and extensive roll-out of mainstream regrind mills as well as several further flotation concentrate regrind mills, over the next six years. Currently 23 stirred mills are in operation with 64 MW of installed drive capacity ? this paper describes the projects? roll-out and the significant results achieved to date. Many operational problems have been solved along the way, some of these will be described. The introduction of the technology has seen a step change in metallurgical results and progressively decreasing operating costs.

Jan 1, 2012

By Chri Rule

"This paper tells the story of the rapid commercial application of stirred milling technology at Anglo American Platinum’s many Concentrators. The first stirred mill – a 10 000 litre IsaMillTM; the largest at the time, was commissioned in late 2003. The project development work was presented at SAG 2001. This operation was “proof of concept” and vindicated the decision to scale up the technology; allowing a rapid and extensive roll-out of mainstream regrind mills as well as several further flotation concentrate regrind mills, over the next six years.Currently 23 stirred mills are in operation with 64 MW of installed drive capacity – this paper describes the projects’ roll-out and the significant results achieved to date. Many operational problems have been solved along the way, some of these will be described. The introduction of the technology has seen a step change in metallurgical results and progressively decreasing operating costs."

Jan 1, 2012

By L. Tong

The nickel laterite ore is composed of soft and hard minerals, and nickel distributes preferentially into the soft mineral rather than in the hard. Selective comminution of saprolitic and goethitic nickel laterites is investigated to upgrade nickel into the fine fraction using stirred milling. The optimal selective grinding conditions were determined through a kinetic study and the limit of selective grinding and nickel upgrade was analyzed. The breakage rates of minerals, grinding time, and the weight ratio of soft and hard minerals in the feed play an important role in selective grinding. A small breakage rate on hard minerals and a large breakage rate difference between the minerals are optimum for selective grinding. The soft mineral grade decreases with grinding time and the optimum grinding time is a trade-off of the soft mineral upgrade and recovery. The minerals weight ratio determines the limit of selective grinding. The effect of nickel upgrade is determined by both the conditions that influence selective comminution and the nickel grades in both the soft and hard minerals. The nickel grade in the soft mineral determines the limit of nickel upgrade.

Jan 1, 2015

By L. Tong

Stirred milling of laterites offers possibilities for improving liberation and selective size reduction of soft nickel-bearing minerals in laterites. Batch grinding tests were performed in a Netzsch LME4 stirred mill on a siliceous goethitic (SG) nickel laterite sample (-2000 µm particle size) to evaluate the effect of operating conditions such as stirrer speed, grinding time, pH, solid content, water salinity and charge volume. The target was to produce a -38 µm fraction in the milling product with high nickel recovery and grade. Addition of dispersant (sodium hexametaphosphate) was also optimized with respect to the rheology of the slurry. In terms of stress intensity, the optimum grinding conditions for selective size reduction were: 1000 rpm, 50 per cent charge volume. At higher stress intensity (2000 rpm), Ni recovery in the -38 µm product was higher, but Ni grade was low, due to the breakage of the harder siliceous particles. Decreasing the yield stress by modifying slurry pH or adding dispersant improved the rheological properties of the pulp, but had no great influence on Ni upgrade in the fine product. Modifying water salinity by adding 2 M NaCl had also little effect. The breakage of the +38 µm particles in the feed determined Ni upgrade greatly. Ni grade in the -38 µm product decreased with grinding time, suggesting that the Ni-bearing minerals break first, while the harder siliceous minerals have a lower breakage rate. The breakage rates with respect to sample mass for Ni, Mg and Si indicate that: Mg > Ni > Mass > Si. The optimum grinding time for the highest Ni upgrade was 0.25 min. The Ni grade increased from 0.88 per cent to 1.35 per cent (upgrade 54 per cent), with 24 per cent Ni recovery. Keywords: fine grinding, stirred media mill, nickel laterite, slurry rheology

Sep 1, 2012