Search Documents

By B. Kyslinger

"In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Foresight Energy, J. H. Fletcher & Company was tasked to design and manufacture a new roof bolting machine with six independent drilling apparatus on board capable of drilling and bolting the roof and ribs with material handling. This is the first Fletcher® six head machine to be designed and built for the mines in the United States. The machine is intended to work in the Illinois Coal Basin. The objective was to produce a machine capable of drilling and installing six bolts simultaneously with a limited number of operators. The goal of the mine is to decrease the time to bolt a cut to improve the safety level of the current roof bolting method, improve efficiency and to improve the bottom line cost of entry development. The customer wanted four mast feed drills at the front of the machine dedicated to installing roof bolts and then another two mast feed drills behind them dedicated to rib bolts. This dictated the requirement of latched controls, which would allow the operator to start drilling one hole and then latch the controls to be able to move on to the next. To accomplish this, we developed a unique hydraulic latch circuit to maintain operator safety and compliance. Guarding was added to prevent an operator from coming into accidental contact with a latched drill. The result of the design is a machine with a single platform and six independent masts with drillheads: four masts strictly for drilling and installing roof bolts on the front of the platform and then two masts on the back of the platform for rib bolts. The feed and rotation controls at each operator’s station include a latch control for drilling. The latch control will allow the operator to lock in the feed and rotation once the hole has been collared, allowing the operator to move on to the next hole. The rear of the machine is equipped with material handling. There are two material pods with winch controls as well as a mesh rack that includes mesh lift, mesh tilt and mesh sump. The six-head roof bolter allows fewer operators to drill and install roof and rib bolts, which in turn lowers the miners’ roof exposure per cut. This design reduces the operator’s exposure from the inherent pinch points and rotary hazards once he has engaged the latch drilling. Therefore the machine will help to decrease the time to bolt a cut, improving productivity while enhancing the ability to operate the machine safely. INTRODUCTION When mining underground it is necessary to support the roof quickly to prevent it from collapsing after an area has been mined. Since the 1950s, the primary method for supporting the roof has been the installation of roof bolts. Roof bolting is one of the most basic functions yet one of the dangerous jobs in the underground mining operation (1). The Mine Safety and Health Administration’s (MSHA) Health and Safety Accident Classification injury database showed an average of 660 roof bolter operator accidents per year over a 5-year period (1999-2003) (2). The numbers show that roof bolting is the most hazardous machine-related job in underground mining. It represents 39 percent of all machine-related accidents in underground coal mines. In 1993, the U.S. Bureau of Mines conducted a study that has shown the activity of drilling as the most hazardous job task performed by a roof bolter operator, accounting for 31 percent of all roof bolting injuries (3). Almost half (46%) of these drilling injuries were due to falling rocks or coal from the roof. All of these injuries occurred under supported roof. The majority of these injuries (about 99%) are not caused by a major roof collapse but from falls of smaller rock from the immediate roof. This type of roof failure has also been termed “skin fall.”"

Jan 1, 2017

By N. Katsikaros, A. Lewis-Gray, P. Richards

"To optimize gold recovery in complex leach-to-electrowinning processes, Gekko Systems developed the Gekko resin exchange column (G-REX) as an intermediate step, using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin. Operational experience has been gained at the Castlemaine Goldfields Ballarat gold mine. In near-continuous operation since 2008, the Ballarat plant treats unclarified concentrate leach solution. The extension of this technology to higher throughputs and more complex chemistry is discussed.RÉSUMÉ Afin d’optimiser la récupération de l’or dans des procédés complexes impliquant la lixiviation suivie de l’extraction électrolytique, Gekko Systems a développé la colonne Gekko de résines échangeuses d’ions (G-REX) comme étape intermédiaire, à l’aide d’une résine hautement sélective pour la récupération de l’or qui permet d’isoler les métaux contaminants. Gekko détient la licence exclusive pour la résine AuRIX®100 produite par Purolite, et la colonne G-REX a été spécifiquement conçue pour cette résine. C’est à la mine d’or Ballarat de Castlemaine Goldfields que l’expérience opérationnelle a été acquise. L’usine de Ballarat, en exploitation quasi-continue depuis 2008, traite une solution concentrée non clarifiée de lixiviation. L’extension de cette technologie à des capacités supérieures et à une chimie plus complexe est examinée.AURIX®100 RESINAuRIX100 resin is a crosslinked polystyrene alkaline resin developed by Henkel (Virnig, Mackenzie, & Adamson, 1996). The resin beads are off-white in colour and spherical, with a nominal size of 100% +600 µm. This resin is highly selective for gold and silver over many metals, by way of extracting precious metal–cyanide complexes from leach solutions with a pH of less than 11.5. The higher end of the pH scale produces the best selectivity according to the order of preference: Au > Ag > Hg > Zn > Ni > Cu > Co > Fe. Purolite produces the resin and Gekko Systems maintains licensing of AuRIX100 resin for use in its G-REX column, as part of its unique suite of gravity gold–handling equipment.Significant cost savings over carbon-in-solution (CIS) systems are realized with AURIX100 resin: approximately 4–12% in capital savings and 27–40% in operating costs (Virnig, Mackenzie, Katsikaros, & Gray, 2004). Additionally, AuRIX100 resin is not susceptible to fouling; that is, the resin does not load with inorganic salts or organic compounds that would affect the loading and extraction of precious metals. To counter any potential for fouling by inorganic salts, a dilute acid wash is periodically conducted in service on the resin to unblock resin pores."

Jan 1, 2017

By O. A. Ojo, N. Esmaeili

"The effects of brazing and use of composite powder mixture as interlayer material on hot corrosion resistance of brazed IN738 superalloy were studied. Brazing was observed to result in significant reduction in the hot corrosion resistance of the superalloy. However, application of composite powder mixture, which consists of additive superalloy powder, enhanced the hot corrosion resistance of brazed samples. It is also found that although the use of composite powder mixture increased hot corrosion resistance of brazed alloy, if the additive powder completely melts, which is possible during brazing, it can significantly reduce the hot corrosion resistance of the brazed joint. Elemental micro-segregation during solidification of the joint with completely melted powder mixture produces chromium depleted zones and consequently reduces hot corrosion resistance, since a uniform distribution and adequate chromium concentration is necessary to combat hot corrosion. This has not been previously reported in the literature and it is crucial to the use of composite powder mixture for enhancing the properties of brazed superalloys.INTRODUCTION Superalloys have been developed in response to the increasing demand for materials with higher resistance to corrosion and creep and also with higher mechanical strength at higher temperatures (Smith, 1981). Ni-base superalloys are predominantly used in manufacturing hot sections of gas turbine engine components. This is due to their high strength and corrosion resistance in extremely high temperature service environments which is typical for hot sections of gas turbine engines (Miglietti, 2009). The continuous demand for higher efficiency and output has resulted in the use of higher operating temperatures and gas pressure in modern gas turbine engines (Jahnke & Demny, 1983). Consequently, this has caused thermal and mechanical stresses which result in severe degradation and damage of gas turbine engine components due to creep, fatigue and hot corrosion (Zhang, Feng, & He, 2006). The decision to replace or repair damaged parts depends on the overall repair cost and expected life of the repaired components (Jahnke & Demny, 1983). However, in most cases, it is more cost effective to repair damaged parts rather than use a full replacement."

Jan 1, 2017

By Long Fan, Shimin Liu, Guijie Sang

"Weak shale roof falls have long been the main cause for fatalities in underground coal mines. Moisture-induced swelling is one of the root causes for the degradation of roof shales. In this study, slake durability tests are conducted on shale samples collected from Illinois basin coal mines, and different levels of durability are analyzed according to Gamble slake durability classification. There are two main mechanisms influencing the shape of retained fragments after two cycles of wetting and drying: mechanical abrasion and swelling pressure. A prototype optically based shale swelling apparatus is designed and manufactured for the shale free-swelling measurement. The experimental results suggest that swelling pressure tends to deteriorate shale laminations. Moisture-induced swelling of the No. 6 roof shale from Bear Run Mine was measured under 100% relative humidity condition. The measured swelling strain normal to beddings is ~5 to 7 times greater than the swelling strain parallel to beddings. This suggests that interlayer expansion plays a key role in moisture-induced swelling. Cracks induced by swelling pressure tend to occur along the bedding plane and lead to shale deterioration. INTRODUCTION Background Ground falls have long been the cause for nearly 50% of all fatalities in underground coal mines and continue to be one of the greatest safety hazards in underground spaces. Among the various ground fall hazards, roof failure takes up 23% of total fatalities in underground coal mines, of which 13% are due to skin failure and 10% are due to massive roof falls (Mark, Pappas, and Barczak, 2011). Roof failures associated with weak shales are summarized in previous studies (Molinda and Mark, 2010; Aughenbaugh and Bruzewski, 1973; Bajpayee, Pappas, and Ellenberger, 2014; Murphy, 2016). For mine roof instability and failure, two aspects can explain the failure mechanism of weak roofs. One is the elevated stress concentration in lateral direction due to the mining-induced excavation and its stress redistribution around the mine opening (Song and Stankus, 1997; Fan and Liu, 2017; Hill, 1986). The other mechanism is the passive stress-relief due to the strength weakening induced by the ambient moisture and temperature fluctuations during a period of time. Shale is moisture sensitive and presents a lower durability if it is exposed to a highly humid environment for a long time, thus leading to roof deterioration and instability in underground coal mines (Aughenbaugh and Bruzewski, 1976; Stateham and Radcliffe, 1978; Chugh and Missavage, 1981; Klemetti, Oyler, and Molinda, 2009). It is well known that shale is a clay-bearing sedimentary rock and that clay minerals are water sensitive. The moisture uptake for shale will induce the micro-deformation of a shale matrix, thus the structure and strength of shale is a function of time and intensity of moisture exposure. All mine engineers notice moisture-induced shale deterioration; however, the underlying mechanism(s) are still not fully understood due to the complexity of geophysical-chemical water-shale interactions (Huang, Aughenbaugh, and Rockaway, 1986; Hensen and Smit, 2002; Diaz-Perez, Cortés-Monroy, and Roegiers, 2007). The coal mining industry is still in the process of finding a technically sound, cost-effective technology to prevent this unexpected and unpredictable shale roof failure. Therefore, understanding how the moisture-sensitive shale responses to various ambient moisture and what role exposure duration plays in shale roof failure is key to prevent unexpected roof incidents, which will lay the foundation for the long-term roof support design and ground control management."

Jan 1, 2017

By P. J. Le Roux

"Mining companies are under constant pressure to reduce their cost structures to sustain profitability. In mines using an open stoping mining method, dilution often has a significant effect on profitability. At Target mine in South Africa, dilution in some open stopes was found to exceed 10%, falls of ground being a major contributor to the problem. This dilution can reduce the recovered grade from 5.5 to 4.5 g/t, resulting in a potential loss of about R21 million per month based on a gold price of R240 000 per kilogram. In addition to the cost of dilution, the cost of damage to, or loss of, trackless equipment as a direct result of falls of ground in open stopes is significant. Other associated costs include transport, hoisting, secondary blasting, milling, and plant treatment of waste material. Stable open stopes are essential in order to reduce falls of ground. Back-analyses of stope instability at Target mine have indicated that conventional rock mass failure criteria are unsuitable for stope design. An alternative strain-based criterion has been developed, and has proved to be very successful, allowing the stability of open stopes to be calculated reliably. Since its implementation in 2010, dilution and equipment damage have decreased markedly, creating value for the mine. IntroductionMines that make use of an open stoping mining method aim to extract only the ore, leaving the waste behind. Many orebodies have well-defined boundaries between the ore and the waste rock. In such orebodies, the introduction of waste into the ore due to overbreak dilutes the grade. In massive disseminated orebodies, dilution is less problematic. Overblasting, falls of ground, or other causes may result in dilution. A study undertaken in Canada (Pakalnis et al., 1995) found that approximately 51% of all underground metal mines utilized open stoping mining methods and, from surveys conducted at these mines, open stoping operations experienced dilutions of up to 20%, and occasionally more. Dilution of this magnitude has a significant economic impact on any mining venture. Research carried out in Australia by Capes (2009) came to the same conclusion."

Jan 1, 2017

By S. H. Amini, A. Noble

"While many classic mineral processing circuit design approaches rely on deterministic methods, numerous studies have shown that the uncertainty inherent to the various input parameters can significantly influence design decisions. In a separation circuit, many of the technical uncertainties can be mathematically represented as statistical distributions for the unit recovery and feed grade. These uncertainties are then propagated by the circuit design and reflected in the circuit performance indicators, such as product grade and global recovery. An effective design strategy entails identifying which units are most influential in this uncertainty propagation and thus merit further consideration. Unfortunately, few analytical tools provide this information, particularly those that rely solely on deterministic methods. However, one promising approach is through the application of Taguchi’s method, in a fashion similar to statistical tolerancing of manufactured products. Since the technical challenges are fundamentally similar, Taguchi’s method shows promise in evaluating the level of compounded uncertainty by various circuit designs while determining the role of each separation stage on the overall selectivity and variability of separation circuits. This paper demonstrates Taguchi’s method in several two and three unit circuit designs. INTRODUCTION AND METHOD DESCRIPTION Uncertainty in Mineral Processing Circuit Design Analysis and estimation of uncertainty propagation in mineral processing separation circuits is an essential and significant aspect of an optimal circuit design procedure. Most of the current circuit design methodologies have been constructed, implemented, and validated using a deterministic modeling approach. However, numerous studies have shown that the inherent uncertainty induced by uncertain design parameters can be a significant factor in many mineral processing applications (e.g. Kraslawski 1989; Xiao and Vien 2003; Ghaffari et al. 2012). Thus, an effective circuit design methodology must be able to quantify uncertainty in separation circuits with limited input data. This paper describes Taguchi’s method, as an experimental design technique, to approximate uncertainty in mineral processing applications, and then the similarity of results between Taguchi’s method and Monte Carlo Simulation is investigated. Monte Carlo Simulation The term “Monte Carlo Simulation” has been used to refer to a variety of stochastic simulation methods spanning a broad array of business, technical, and scientific domains. Most generally, Monte Carlo Simulation refers to numerical analysis which is based on (pseudo) random sampling from a domain of input parameters with a known statistical distribution. This methodology allows one to determine the distribution of expected results from a standard deterministic process model. Execution of a Monte Carlo simulation begins by identifying the domain of input parameters, statistical distributions for each parameter, and a deterministic process model which describes the anticipated result as a function of the inputs. Next, one discrete random sample is taken for each input parameter, considering the input distributions. The process model is then solved for this mix of input parameters, producing a single simulation result. This procedure is then repeated a “large” number of times, utilizing new randomly sampled input parameters for each simulation iteration. Once the desired number of iterations is reached, the results of each independent simulation are aggregated to produce descriptive statistics such as minimum, maximum, mean, standard deviation, kurtosis, and other distribution parameters. Given enough iterations, the Monte Carlo method fully explores potential synergies between the input parameters. The methodology does not require the process model to be differentiable, continuous, or even analytically defined. While the number of required iterations varies in relation to th"

Jan 1, 2017

By T. Joseph, E. Zheng, M. Curley

"Hydraulic transportation efficiency and production optimization are considerations in the surface extraction of Athabasca oil sand deposits. To reduce the dependence on haul trucks, it is possible to extend the hydraulic transport system to production faces using a mobile at-face slurry system (AFSS). The flexible arrangement of connected pipelines transports slurried minerals from the mining face to the processing plant. An experimentally verified mathematical model indicates the friction loss of oil sand slurry associated with the AFSS. Laboratory-scale testing enables extended analyses for examining pipeline slurry transport in an oil sands environment.RÉSUMÉ L’optimisation de l’efficacité du transport hydraulique et de la production sont des considérations importantes dans le domaine de l’exploitation à ciel ouvert des gisements de sables bitumineux de l’Athabasca. Afin de réduire la dépendance envers les camions de transport, on envisage d’étendre le système de transport hydraulique aux fronts de taille à l’aide d’un système mobile de transport des matériaux sous forme de boue à partir du front de taille (AFSS, de l’anglais at-face slurry system). L’organisation flexible des conduites reliées permet le transport de minéraux à l’état de boue du front d’exploitation jusqu’à l’usine de traitement. Un modèle mathématique vérifié de manière expérimentale indique la perte de charge par frottement des schlamms provenant du traitement des sables bitumineux associée à l’utilisation de l’AFSS. Des essais en laboratoire permettent de mener des analyses approfondies portant sur le transport de boues dans des conduites dans un environnement de sables bitumineux. INTRODUCTIONObjectives and scope of studyThe at-face slurry system (AFSS) concept has become a competitive means for materials handling to optimize haulage system efficiency and cost. The mobile and flexible arrangement of the AFSS introduces a unique set of hydraulic transport problems. This paper will focus on developing the mathematical models governing the friction and head losses within the AFSS concept.Background of the problemLarge-capacity shovels and dump trucks are increasingly used for excavation, loading, and hauling in the operation of surface mining. Production cost and efficiency optimization are demanded during the Athabasca oil sands (Alberta, Canada) mining process to secure North America’s energy supply. Increasing haulage distances, rugged terrain, and a constrained mine environment are conditions that will reduce the effectiveness of the shovel-truck haulage system (Frimpong, Szymanski, & Changirwa, 2003). In such conditions, the tire heat index and weight, distance, and time limits for truck haulage can be exceeded, simultaneously creating extreme tire wear and high maintenance costs. In addition to low production cost and equipment effectiveness, a mining environment also requires efficient waste-material recycling and distribution. Waste materials need to be recycled from the processing plant to a new destination such as a tailings dam, or replaced in mined-out areas such as backfill. The Athabasca oil sands configuration and location characteristics result in a mining environment that would benefit from flexible pipelines for constant production and an efficient waste-material recycling process."

Jan 1, 2017

"Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor a production blasting in a quarry. The production blast consisted of double-decked explosive loads in 155 mm (6 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsionexplosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and thevibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of micro-cracks along the joint surface as a function of the vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring."

Jan 1, 2017

By Elizabeth Varghese, Sanket Rawat, Prachuryya Kaushik, Ravi Kant Mittal

"Geo5 Software is gaining popularity worldwide due to its expediency in analysis and design of pile foundation. The analysis is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards. Moreover, the ultimate resistance of pile in the software is based CSN 73 1002, Fellenius method, NAVFAC DM 7.2 and Tomlinson method. Due to the specificity in calculation of ultimate resistance, it becomes necessary to validate the results arrived using the software for better accuracy. Furthermore, the above-mentioned methods are not necessarily popular in every design offices. Therefore, an attempt has been made to predict the efficiency of Geo5-v15 software to analyze the pile foundation by comparing it with the results obtained using the analysis based on Indian Standard IS 2911:2010, performed with spreadsheet specifically designed for the same purpose. The accompanying outcome of the comparison and several shortcomings found in the design part associated with the software has been highlighted in the later part of the paper. Besides, the optimization tool present in the software is also described for the more efficient and economic design of pile foundation, hence contributing as practical aid to structural engineers.INTRODUCTIONThe analysis of individual pile foundation and pile in groups can be said to include the three main important parameters – Ultimate bearing capacity, Settlement and Structural Design. The first two parameters are to be evaluated to check the reliability of foundation against ultimate limit state and serviceability limit state. The third parameter includes the analysis of pile against both horizontal and vertical load. This parameter mainly intends to evaluate the size of foundation and the amount of reinforcement. Geo5 is a software which can expediently compute the above mentioned three parameters just by the mere input of the necessary factors. The ultimate bearing capacity analysis in Geo5 is based on various theoretical, empirical and semi-empirical methods available in existing literature and various country standards depending upon the drained and undrained condition of soil (Bowles, 1968; CSN 73 1002,1987; Felenius,1991; NAVFAC DM 7.2,1984; Tomlinson,1977). However, the method mentioned in IS 2911 (2010) is not the same and have slight variations in way of evaluating the parameters which affect ultimate bearing capacity. Therefore, it becomes necessary to evaluate the efficiency of Geo5 with respect to the value of ultimate bearing capacity and therefore, asserting the confidence in the software based method for the convenience of the designs in Indian Scenario. The present study aims to evaluate the efficiency of Geo5 v-15 software in predicting the ultimate bearing capacity of pile foundation. The results of the software are compared with the bearing capacity calculated using IS 2911 (2010) with the help of excel sheet. Moreover, as the software is frequently put under revision, therefore a comparison of this version has also been made with the latest version of Geo5 (2017) to check whether the latest revision has accounted for the discovered shortcomings. The design steps performed in the software is also shown. As Geo5 make use of IS 456 (2000) for the design purpose, hence it can be considered as reliable with respect to the estimate of the third parameter. Furthermore, the optimization process is also shown in the later part of the paper to emphasize the simplicity of the software in economizing the design cost."

Jan 1, 2017

By Dominic Parmantier, Karen Dawson, Suthan Pooranampillai, Seungcheol Shin

"This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.IntroductionStone column ground improvement was implemented as a means of supporting mechanically stabilized wall approaches for a new bridge over the Puyallup River, part of HOV improvements to I-5 in Tacoma, Washington. The work discussed in this case history was part of the Washington State Department of Transportation (WSDOT) I-5/Portland Avenue to Port of Tacoma Road, Stage 1 Northbound HOV contract, developed as an early work element to a follow-on bridge construction project. The area requiring stone column ground improvement is shown in Figure 1. The improved ground supports permanent geosynthetic walls and embankments up to 50 feet high. This wall can be seen in Figure 1. The selected ground improvement primarily provides global stability of the soils beneath the walls during anticipated seismic loading and also reduces the time and magnitude of consolidation settlement under the weight of the planned embankment.Approximately 74,000 cubic yards of liquefiable alluvial soils were improved by stone columns. Stone column construction occurred in late 2010 and early 2011. This was followed by the embankment and wall construction. Settlement monitoring began with the embankment construction and continued into 2012."

Jan 1, 2017

By Howard A. Perko, Melinda J. Hummel

"Hydraulically jacked piles, herein referred to as jacked piles, are commonly used for underpinning existing structures to arrest settlement or augment an existing foundation for higher loads. They consist of steel pipe segments coupled together and jacked into the ground using a hydraulic ram. Pipe sections can vary in size from 3"" diameter to 18"" diameter or larger. Jacking resistance is typically provided by dead loads of existing structures. This type of piling system has been utilized for foundation underpinning, repair, and augmentation for more than 120 years, yet little has been published on the capacity, installation standards, and reliability of these systems. Pile load tests from a number of projects are presented and analysed. The data show that previous methods of jacked pile capacity and depth prediction are crude at best. Empirical relationships between capacity, depth, soil type, and standard penetration resistance blow count contain a high degree of scatter. Scatter in the data indicate capacity prediction for jacked piles needs further research and refinement.INTRODUCTIONPush pier, resistance pile, steel pier, and jacked pile are some of the names often applied to hydraulically jacked piles used for underpinning. The term ‘jacked pile’ is more common in building codes and will be used herein. Although jacked piles can be installed for new construction, this paper is focused on piles used for support of existing structures.Jacked piles consist of short segments of pipe or structural steel tube that are coupled together and forced into the ground using a hydraulic ram fastened to or beneath a footing, stem wall, or grade beam of an existing structure. In this way, the weight of the structure provides the resistance necessary to force the pile into the ground. A factor of safety can be achieved in design by redundancy, which is consecutively installing more than one jacked pile to support the same portion of foundation. Installing jacked piles consecutively using the same dead load and then releasing the load after each pile installation allows one to continue adding piles to the same general area until a total aggregate capacity is achieved to account for anticipated dead plus live loads and a desired factor of safety for that area.An engineering schematic of an example jacked pile connected to a footing foundation is shown in Figure 1. Modern jacked piles typically incorporate a steel bracket. There are many sizes and styles of brackets available. Some categories include plate brackets that bolt to the outside of an existing foundation wall, wide and narrow angle brackets that extend under existing footings, pin brackets for attachment to structural steel, and reverse angle brackets for attachment to footing and wall. Table 1 lists example brackets and their benefits."

Jan 1, 2017

By John Dunn, Matt Hawley, Kashif Butt, Nicholas Gura

"This paper presents the results of a static load testing program completed on helical pile foundations for the replacement of high voltage transmission line tower structures. The foundations were part of the Northeast Grid Reliability Project (NGRP) for the Public Service Electric & Gas Company (PSE&G) near Newark, New Jersey. Structure foundations “anchor bolts down” was a design build contract model with the superstructure as bid-build.The soil stratigraphy along the alignment generally consisted of fill over about 10 ft of organic deposits underlain by up to 260 ft of normally consolidated glacial lake clays and silts. Additional project challenges included working under/adjacent the existing live high voltage lines, narrow site access due to environmental permits, foundations in a tidally influenced area, and pile projections in the order of 10 feet to meet the 10 year flood level requirements.The helical piles were constructed of 12.75 inch diameter open ended pipe piles with 36 to 40 inch diameter helices. A total of seven static load tests (compression and tension) were completed on 60 ft and 90 ft long piles, using both welded and mechanical pile splices. To evaluate pile-soil setup in the sensitive fine grained soil and determine representative longer term installation torque factors (Kt) for the production piles, the static load tests were performed 7 to 49 days after pile installation.Helical piles were found to be the most cost effective foundation alternative for this project. The required length of helical piles was less than other alternatives for similar allowable axial capacity. Helical piles with mechanical splices were installed for the varying structure foundations including tangent and heavy deadend, to a deadend monopole. Installation of 448 production piles (34,320 linear ft) was completed in three months. The installation timeline was critical to meeting the semi-annual PSEG outage for switching the old and new structures. Helical piles employing a mechanical splice resulted in an efficient and effective foundation solution for the conditions encountered on the project."

Jan 1, 2017

By M. Hesham El Naggar, Mehdi Heidari

"Equivalent fixed-base cantilever model is a common approach for performance base seismic design of bridge structures supported by extended pile-shaft. In this method, global displacement ductility factor is related to local curvature ductility demand by assuming a concentrated plastic hinge at location of maximum bending moment. Equivalent plastic hinge length is one of the key parameters that should be assumed accurately in kinematic expression of the cantilever model. Although, some expressions have proposed to estimate the length of the in-ground plastic hinge; however, these relations yield differing results. In this paper, a general expression is derived based on the concept of distributed plasticity to predict the plastic region of yielded piles in clay and sand. A length modification factor is defined to relate the equivalent length of plastic hinge to the real plastic zone. Then, results from nonlinear pushover analyses are used to propose an equation for the modification factor as a function of displacement ductility factor.IntroductionDuring severe earthquake events, development of the plastic hinge in pile foundation below ground level is inevitable for bridge structures supported on extended pile-shafts. A common approach for seismic design of the yielding pile-shafts is to replace the pile-soil system by an equivalent fixed-base cantilever assuming the equivalent system has the same global response as that of the pile-shaft (Budek et al. 2000; Chai 2002). In this method, plastic curvature is concentrated at the center of the equivalent plastic hinge below ground surface. Prior knowledge of plastic-hinge length is essential for proper assessment of assess plastic displacement at the top of the pile-shaft. Unfortunately, existing recommendations for estimating plastichinge length are largely incomplete and/or inadequate.During the last two decades, several relationships have proposed for evaluating the equivalent plastic hinge length, Lp, based on experimental and numerical studies. Budek et al. (2000) conducted numerical modeling to calculate the plastic-hinge length of piles embedded in cohesionless soil. They found that the plastichinge length varies linearly with both soil stiffness and aboveground height, e. Chai and Hutchinson (2002) conducted full-scale experimental tests on reinforced concrete piles in sand. They reported that Lp depends primarily on the aboveground height of the pile, neither sensitive to the soil stiffness nor to the value of displacement ductility factor. They stated that the equivalent plastic hinge length is relatively independent of the displacement ductility factor and is not very sensitive to the change in soil density. On the contrary, Goel (2014) and Liu et al. (2016) conducted nonlinear numerical analyses which revealed that Lp changes with the displacement ductility factor and even suggested that using different values of Lp for different seismic design levels is essential for a reliable estimation of the ductility capacity."

Jan 1, 2017

By J. Cayouette, C. Bolduc, P. Blatter

"The LaRonde mill was commissioned in 1988 and began treating ore from the Penna shaft in 2000. The mill has been expanded to accommodate 7,500 t/day, but ramped down to 6,000 t/day since the deep extension began. The process recovers gold, silver, and base metals. In 2008, the Goldex plant began trucking gold-pyrite concentrate to a treatment plant feeding pulp to the LaRonde mill, increasing gold output by 40,000 oz. In 2009, the high-grade Lapa ore processing facilities were annexed to the LaRonde plant, increasing gold output by 120,000 oz. This paper outlines the metallurgical considerations related to the treatment of different ore types.RÉSUMÉ Le concentrateur de la mine LaRonde a été mis en service en 1988 et a commencé à traiter le minerai du puits Penna en 2000. La capacité du concentrateur a augmenté afin de permettre le traitement de 7 500 tonnes de minerai par jour, capacité qui est retombée à 6 000 tonnes par jour (tpj) depuis le début de l’extension en profondeur de la mine. Ce procédé permet de récupérer de l’or, de l’argent et des métaux communs. En 2008, l’usine de traitement Goldex a commencé à transporter par camion du concentré de pyrite et d’or vers une usine de traitement alimentant en pulpe le concentrateur de LaRonde, augmentant ainsi la production d’or de 40 000 onces. En 2009, les installations de traitement du minerai à haute teneur de Lapa ont été annexées à l’usine de traitement de LaRonde, augmentant la production d’or de 120 000 onces. Cet article passe en revue les considérations métallurgiques liées au traitement de différents types de minerai.INTRODUCTIONThe LaRonde metallurgical plant in the Abitibi region of Quebec, Canada, evolved into a mature milling site following expansions in 2000–2003, thanks to improved processes, manpower, and water treatment capabilities that better accommodate the complex constituents of the LaRonde ore. The ore requires a sequence of grinding, copper- lead and zinc flotation, and precious metals leaching, ending with a carbon-in-pulp (CIP) gold recovery. A portion (35%) of the tailings is sent back underground as paste backfill after being treated with the SO2-air cyanide destruction process. The tailings area has a dedicated cyanide destruction and metal precipitation area through which the used water passes before returning as recycled water. A biological water treatment plant was built in 2004 to address water toxicity in the final effluent. The water toxicity was the result of the high sulfide content of the LaRonde ore (from thiocyanate or stable cyanide species buildup) and the use of 90% recirculated water in the mill. The water treatment plant uses bacteria to transform thiocyanate into nitrates and precipitate phosphorus from the water before it is discharged into the environment."

Jan 1, 2017

By B Mohanty, A Siamaki, K Esmaeili

Large scale open pit mining and quarrying operations dictate safe and reliable pit wall stability. The current approach of employing the particle velocity-scaled charge distance approach to estimate and minimize damage to residential structures is considered inadequate to protect rock slopes. This study utilizes close-in blasting vibration data as input to an advanced 2D numerical code to study its applicability to serve as a predictive tool in terms of blast-induced rock slope failure. Two tri-axial accelerometer stations, consisting of high-frequency and high-amplitude (20 kHz, 100g) sensors, located within ~100m of the blast, but at two different bench levels, were used to monitor production blasts in a limestone quarry. The production blast consisted of double-decked explosive loads in 125 mm (5 in) diameter holes, with an inter-deck delay of 42 ms, and each deck consisting of 130 kg (285 lb) of emulsion explosive. The blasting vibration data obtained at the two bench levels were critically analyzed, and the vibration results served as input to the numerical model consisting of a single rock block with a 45 degree persistent joint plane but with specified strength properties, significantly different from that of the intact rock. The model was able to characterise progressive accumulation of damage in the form of microcracks along the joint surface as a function of the relatively low vibration load from successive explosive decks. The results showed that such a numerical model can serve as a very good diagnostic and predictive tool, when backed up by careful vibration monitoring and further supported by detailed slope monitoring.

Jan 1, 2017

By Md. Nafiul Haque, Murad Y. Abu-Farsakh, Chris Nickel

"This paper presents the results from a pile load testing program for a bridge construction project in Louisiana. The testing includes two 54-inch open-ended spun cast concrete cylinder piles (OECP), one 30-inch open-ended steel pile (OESP), and two (30-inch and 16-inch) square prestressed concrete (PSC) piles driven at two locations with very similar soil conditions. All the test piles were instrumented with vibrating wire strain gauges to measure the load distribution along the length of the test piles and the skin friction and the end bearing were derived from strain gauge measurements. High strain dynamic load tests (HSDLT) were performed on all test piles at different times after pile installations to quantify the amount of setup with time. Static load tests were also performed on the PSC and open-ended steel piles. Due to expected large pile capacities, the statnamic test method was used on the two open-ended cylinder piles. The pile capacities of these piles were evaluated using various CPT methods (such as Schmertmann, De Ruiter and Beringen, LCPC, COFS methods). The result showed that all the methods can estimate the skin friction with good accuracy; but not the end-bearing capacity. Setup was observed for all the piles, which was mainly attributed to increase in skin frictions. The setup rate parameters “A” [The “A” parameter is defined as the rate of increase of pile capacity ratio (Rt/Rto) per log cycle of elapsed time] were back-calculated for all the test piles and the values were between 0.31 and 0.41.INTRODUCTIONDue to greater efficiency (capacity to weight ratio) of the pipe piles, open-ended piles are a viable option to solid piles. However, the behavior of open-ended piles is more complicated compared to the close-ended piles owing to possible formation of “soil plug” inside the open-ended pile. Many researchers have analyzed the behavior of both types of piles for different purposes; however, very few studies in the literature offer the side-by-side comparison of the close-ended and open-ended piles."

Jan 1, 2017

By Paul Thurlow, Richard K. Lipscombe

The measurement of deflection of designed diaphragm walls is critical for near real time information to assess wall and soil behaviour as the internal area is excavated in a controlled manner. Data enables the site team and designers to check performance of the design, which is linked to safeguarding the site and the external stakeholders.This paper documents the use of Shape Accel Arrays at the Tottenham Court Road Western Ticket Hall during excavation and propping within the diaphragm wall for the Crossrail project. It shows how the data obtained was used within the site settlement management plan to assist in the control of the works and the information used for Value Engineering purposes that benefitted the project.The use of Shape Accel Arrays for measuring the deflection of retaining walls is not commonplace in the UK construction industry, with the Tottenham Court Road Western Ticket Hall being one of the first times they have been used in such a way. A detailed analysis of the data obtained from the instruments has been undertaken, and compared to the results obtained from the manual inclinometers that were read next to the SAAs. The advantages of the relatively new SAAs have been discussed, as well as other applications of the instrument.

Jan 1, 2017

By Gerald Verbeek, Erick Baziw

"Downhole Seismic Testing (DST) is an important geotechnical testing technique for site characterization as it provides low strain (<10-5) in-situ interval compression (Vp) and shear (Vs) wave velocity estimates. These velocities are determined by obtaining relative arrival times of source waves as they travel through the stratigraphy and are recorded by one or more vertically offset seismic sensors. A challenging aspect of this process is to characterize the seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. This paper introduces an assessment technique which utilizes linearity estimates (i.e., hodograms fitting straight lines) from the polarization analysis in conjunction with crosscorrelation coefficient calculations of the full waveforms as well as the deviation of the source wave frequency spectrum from a desirable bell-shaped curve. The paper will provide an overview of the technique and include some examples of actual data sets where the technique was applied to analyze those data sets.1. INTRODUCTIONIn general terms, Downhole Seismic Testing (DST) such as Seismic Cone Penetration Testing (SCPT) is a geotechnical technique for measuring in-situ shear and compression wave velocities (VS and VP respectively). The main goal in DST is to obtain arrival times as the source wave travels through the soil profile of interest, and from these arrival times the velocities are then calculated. Figure 1 shows a schematic of the typical DST configuration: a seismic source is used to generate a seismic wave train at the ground surface. One or more downhole seismic receivers are used to record the seismic wave train at predefined depth increments. The downhole receiver(s) may be positioned at selected test depths in a borehole or advanced as part of an instrumentation package as in the case of SCPT. When triggered by the seismic source a data recording system records the response of the downhole receiver(s)."

Jan 1, 2017

By Shawna Munn, Nadir Ansari, Allison Bennett

"This paper outlines how specification driven design has made Toronto Area transit infrastructure projects more expensive than similar private projects, and provides a case study of the results of an excavation at Launch Shaft 1 (LS1) for the Eglinton Crosstown Light Rail Transit project in Toronto, Ontario. The paper will describe the impact specification driven design parameters can have on design economy, constructability, and schedule and will suggest an alternative approach utilizing the Observational Method. As a result of the initial specification based design, Isherwood was retained by both the General Contractor and the Specialty Excavation Shoring Contractor to provide value engineering leveraging the Observational Method to improve constructability and construction schedule. By using well known, accepted design methods coupled with local experience in lieu of the specified design pressures and parameters, the redesigned bracing scheme reduced construction cost and schedule. This excavation case history can be a lesson learned for future transit projects.The City of Toronto has been developing its transportation network since the mid 1800’s. “Canada’s First Subway” along Yonge Street opened in March 1954 (TTC 1954), with a few additions to the subway network through to the 1980’s. The following two decades marked a long period of slow development due to recessions, budget cuts, and politics along with several cancelled projects. To fill the gap left by years of underfunding, several new transit projects are now under construction in the city as a part of Metrolinx’s $50B, 25 year, “The Big Move” initiative (Metrolinx 2013). The work on these types of infrastructure projects is highlighting a different and developing challenge within the tendering and design specification structure we will call Prescriptive Specification Design (PSD).PSD is a method used within contract specifications to control design risk on a project by applying conservative design methods, factors of safety, or other parameters to make a “fool proof” design. It is akin to requesting a colouring by numbers approach from a painter. There are inherent risks of using this method of tendering a project including increased project costs, longer construction schedules, and decrease of overall project economy. In PSD, the Owner “owns” all of the design risk on a project, including any additional costs due to changed site conditions. However, the Contractor commonly “owns” the risk of any deviations from the design specification they pursue, therefore making any improvements to the design, cost, or schedule less desirable from the Contractor’s point of view. The impact of this type of strict specified approach to design has been seen in transit infrastructure projects in the Toronto area. Figure 1 outlines the range of specified AEPD design pressures as a function of excavation height (H) specified for use in Toronto underground transit projects since the 1970’s to present day. A clear trend can be seen with respect to increased design pressures specified. The ranges shown for each project are intended to account for the potential differences in soil conditions for the highly overconsolidated glaciated soils in the Toronto area. The graph also highlights the typical range, in blue, for the industry practice in Toronto for comparison."

Jan 1, 2017

By Neil T. Russo, Peter M. Kandaris, Jogi S. Gadok

"Assessment of subsurface data for foundation design in support of long high voltage electric transmission lines is best accomplished using a probabilistic strategy since only a small portion of structure locations are typically sampled. Probabilistic approaches provide a tool to evaluate site uncertainty in a systematic and rational manner. This paper provides a case history of a risk-based design approach for a recently completed 191-mile long 69/161/345kV steel monopole transmission line traversing Central Iowa. The project owner made available limited subsurface information at project initiation, requiring the design team to obtain additional data within a constrained budget for 1067 large diameter, laterally-loaded deep drilled shaft reinforced concrete piers. The team commissioned a geologic desktop study to reduce uncertainty in subsurface evaluations and aid in selecting additional sample sites. In total, investigation programs tested approximately 15 percent of structure sites. The paper details the probabilistic approach used to estimate foundation geotechnical design parameters, with information from the various studies categorizing strata both laterally and with depth. Low-bound parameters were estimated via a statistical approach at a predetermined reliability level. Significant savings resulted from this approach when compared to conservative deterministic processes. Project QA/QC logged subsurface soil conditions during foundation excavation, then compared as-found conditions to the conditions assumed for design. The team redesigned foundations if either a non-conservative variance in soil conditions was observed or if bedrock elevation differed significantly from design assumptions. As a result, only 22 out of 1067 foundations required modification during construction (2% variance from initial design) with negligible impact on the construction budget and schedule.INTRODUCTIONFoundation design for long high voltage transmission lines presents a unique challenge in that the assessment of subsurface conditions typically requires substantial data that may or may not be obtainable. Investigations are usually performed well in advance of construction, often with limited access to structure sites and typically in remote areas. Probability and risk-based investigation and design strategies offer an opportunity to systematically estimate subsurface profiles and geotechnical design properties with limited data. Risk can be further reduced with dedicated field inspection of foundation construction along with good field and design team communication during construction. This paper presents a case history of probabilistic methods used for the investigation and design of electric transmission line foundations."

Jan 1, 2017