Search Documents

By B. H. Caudle, A. R. Khan

The oil production performance of thin-oil-column type reservoirs producing entirely by natural water drive are discussed in this paper. The dimensionless production histories were obtained in a series of scaled porous-medium laboratory-model tests under varying effects of rate of production, mobility ratio across moving boundary, ratio of oil- and water-sand thickness and mobility ratio across fixed boundary including the effects of different residual oil saturations in the water-invaded regions. This scaled-model study of thin oil columns indicated that greater recovery of oil results for lower values of the following: rate of production, mobility ratio across the moving boundary, water-sand thickness relative to the oil-sand thickness, and mobility ratio across the fixed boundary or residual oil saturation in the water-invaded region of oil sand The results of the study are given as dimensionless production history plots which may be used to predict the performance of the field they represent. INTRODUCTION Oil fields producing under natural water drive can be classified into two major groups: (1) an "edge-water drive" reservoir group in which the water is encroaching from the reservoir periphery, and (2) the group of reservoirs in which the oil-sand is entirely underlain by an aquifer. Reservoirs in the second group are further subclassified as "bottom-water drive" reservoirs and "thin-oil-column" reservoirs. The latter reservoirs are characterized by their relatively equal oil- and water-sand thicknesses and by having both the oil and water zone relatively thin. When oil is produced from a water-drive reservoir by a partially penetrating well, water breaks through sooner or later before all of the displace-able oil is recovered. Many analyses of this general situation have been made with varying degrees of realism in their approaches, both theoretical and experimental5.6 in nature. Pertaining to the scaled laboratory model studies of natural water drives using porous media, detailed investigations have been made by Henley, et al.7 on bottom-water drive and by Caudle8 on edge-water drive reservoirs. No laboratory model studies, however, have been made to investigate the performance characteristics of thin-oil-column reservoirs. This paper presents the results of a study on scaled models of thin-oil-column reservoirs, operated under varying conditions corresponding to the actual field practices. SCALING PARAMETERS The object of scaling is to produce a one-to-one relationship between physical and dynamic parameters of the model -and prototype. The most comprehensive treatment of scaling techniques for oil reservoirs is given by Geertsma, et a1.,9 which covers two methods for arriving at dimensionless groups for scaling. Table 1 lists the scaling parameters suitable for creating kinematic and dynamic similarities between the model and the prototype in the variables considered for the thin-oil-column reservoirs. In order to achieve similarity it is essential that the dimensionless groups listed in Table 1 have equal values in the model and the protorype simulated. Since it has been established that the role of interfacial forces is neglible in gross fluid movement in a reservoir no attempt was made to scale capillary forces- Although there are reports describing Scaling criteria for these forces,10,ll consideration of the necessary but restrictive conditions for

Jan 1, 1970

By J. S. Pascover, J. K. Abraham

The influence of the early stages of precipitation on the kinetics and structure of martensite formation in Fe-27Ni and Fe-29.5Ni alloys containing from 0 to 10 pct Ti was examined with X-ray and electron microscopy techniques. The formation of a coherent, ordered preprecipitate had a profound stabilizing effect on the austenite. The Ms was decreased by increased titanium content and aging time up to a critical time. When the critical aging time was exceeded, the Ms was observed to increase markedly. The formation of the clusters was insuppressible and the volume fraction of clusters formed during the quench was a function of the titanium content. Martensite resulting from transformation of the clustered austenite is tetragonal with the c/a ratio increasing with titanium content. A model for the tetragonality is suggested. The morphology and substructure of the m artensite is inter-preted in terms of the above information and the cur-rent models of twinned martensite. ThE ramifications of precipitation in austenite to the properties of austenite have been the subject of numerous investigations. The current research is concerned with the influence of precipitation in austenite on the kinetics and structure of subsequent marten-site formation. In a previous investigation, Abraham et al.1 followed the aging reaction in an Fe-29.5Ni-4.2Ti* (at. pct) alloy using an X-ray diffraction technique. This technique, employing a Guinier camera, provided kinetic measurements through observation of the side band position as a function of aging time. The salient results of this work were: 1) The initiation of precipitation was not suppressed by quenching, i.e., there was a finite cluster zone size at zero aging time; and 2) The hardness of the aged austenite correlated extremely well with the zone size. During the previous work it was noted that the mar-tensite formed after aging was tetragonal, substanti-ating an earlier observation.2 Systematic investiga-tion revealed that the martensite was tetragonal in both the solution-treated then quenched, and the solu-tion-treated, aged, and quenched condition, and, furthermore, that a marked stabilization of the austenite occurred as a function of aging time. The present work is concerned with documenting the tetragonality and the stabilization phenomena as well as the ob- served microstruction with a suggested rationale for the behavior noted. EXPERIMENTAL PROCEDURE The compositions of the alloys are listed in Table I. The analyses were performed after the solution treatment of the strip material. Nickel was determined using the standard dimethy1-glyoxime procedure whereas titanium was determined colorimetrically with hydrogen peroxide and volumetrically by titrating with ferric iron. The materials were melted in a 5-lb vacuum induction furnace, cast into 2-in.-diam ingots, and forged in a temperature range of 950. to 1200°C to 1/2-in. slabs. The three higher titanium containing materials cracked during forging; therefore, to get the alloys into strip form, slices 1/8 in. thick were cut from the slab, homogenized 4 hr at 1150°C, then cold-rolled to a 0.04-in. thickness. The remaining slabs were hot-rolled, homogenized 4 hr at 1065"C, then cold-rolled to a final thickness of 0.03 in. All of the heat treatments were performed under a protective atmosphere of argon. The Ms temperature for most of the alloys is below room temperature; therefore, it was possible to solution treat, quench to room temperature, polish, and then observe the transformation optically on a cold-stage microscope. To determine the effect of aus-tenitizing temperature on Ms, eight of the alloys were treated at two temperatures, 1025" and 1120°C. No measurable variations in Ms were noticed. The remaining alloys were treated at 1025°C. The specimens, : by 5/16 by 0.03 in., were austeni-tized in a vertical tube furnace under a dynamic argon atmosphere. The bottom of the tube was submerged in water for quenching purposes. The question of stabilization that may be operating at room temperature was investigated and found to be negligible. Many of the specimens were held at room

Jan 1, 1970

By B. A. Wilcox, A. H. Clauer

The tensile and creep deformation characteristics of fiber reinforced composites have been studied, primarily at room temperature. The matrix was an alloy of Mg-14 wt pct Li-1 wt pct Al (LA141A alloy) and the reinforcing fiber consisted of continuous wires of a high strength precipitation hardening stainless steel (AFC-77 alloy). The ultimate tensile strength and strength-to-density ratio of composites were much improved over that of the mmix, both at room ternperatwe and up to 200°C. Creep studies at room temperature revealed logarithmic weep behavior for wires and composites and steady state creep for the nonreinforced matrix. It was concluded that creep of the fibers controlled composite creep. The instantaneous logarithmic weep rate of the composite, 6, was related to the average tensile stress on the fibers, where n = 3.4. Mg-Li alloys are the lightest structural metals commercially available, e.g., the alloy LA141A (Mg-14 wt pct Li-1 wt pct Al) is 27 pct less dense than beryllium Although Mg-Li alloys have moderate tensile strengths at normal strain rates and ambient temperature, their creep strength is relatively poor, even at room temperature. Reinforcement by fibers offers a means of increasing the tensile strength as well as overcoming the limitations of low creep strength. With a proper choice of reinforcing filament, composites could be designed with higher strength-to-density and modulus-to-density ratios than the matrix alloy. This communication reports a study on the tensile and creep characteristics of alloy LA141A reinforced with continuous wires of a high-strength precipitation hardening stainless steel (AFC-77 alloy). The matrix has a bcc structure, with possible precipitates of AlLi and MgLi2A1,3 and is ductile at room temperature Stainless steel wire was chosen as the -reinforcing filament since previous work at Battelle4 showed that a good bond between wire and matrix could be produced in this system. For all volume fractions of reinforcing wire, the theoretical composite strength-to-density ratio is greater than that of the matrix and the modulus-to-density ratio is somewhat lower than that of the matrix. EXPERIMENTAL PROCEDURES The 0.004-in. diam AFC-77 wire was obtained from two suppliers: National-Standard Co.* and Crucible 0.13 Si, 0.18 V, 0.011 P, 0.012 S, balance Fe. In the as-received condition, wires from both sources had room-temperature ultimate tensile strengths of 585,000 to 590,000 psi with approximately 2 pct total elongation and 40 pct reduction in area. Composite preparation was accomplished by the vacuum infiltration technique. This involved placing the continuous wires in a mild steel tube (1/8-in. ID), capping one end of the tube with a sheet of the matrix alloy, and evacuating the other end of the tube. When the capped end was placed in a crucible of the molten matrix alloy and held for 31/2 min at 70O°C, the liquid metal was drawn up the tube approximately 7 to 8 in. A cross-sectional view of a typical composite is shown in Fig. 1. This preparation technique promoted excellent bonding between the matrix and wires, and porosity was rarely observed. Test specimens for both creep and tension studies were prepared by machining off the steel tube. Tensile tests on the wires and composite specimens were made in an Instron using a cross-head speed of 0.01 in. per min. The composite specimens had no reduced section and were held in self-tightening grooved serrated grips. Most of the specimens broke in the effective 1-in. gage section. Even though several tests fractured in the grip section, their ultimate strengths were essentially the same as those of specimens which fractured in the gage section. Creep specimens of the composite were gripped in a similar manner, and

Jan 1, 1970

By Richard H. Siller, Rex B. McLellan

A model for interstitial solid solutions has been considered in which a repulsive Potential exists between interstitial atoms in the solvent lattice. It has been shown that this model is consistent with the thermodynamic Properties of certain interstitial solid solutions. The model is then applied to the calculation of the variation of the diffusivity of carbon in au-tenite with composition. Although the energy levels at the saddle point, and thus the absolute values of dif-fusivity, cannot be calculated, it is shown that by taking the repulsive interactions between the diffusing atoms into account the functional form of the dependence of diffusivity on solute concentration can be derived. ThE composition dependence of the diffusivity, D, of carbon in austenite at a given temperature is well-known.'-3 smith3 tried to reconcile the observed composition dependence of D at 1000°C with the previously observed4 composition dependence of carbon activity using equations for D derived by arken5 and Fisher, Hollomon, and Turnbull,6 but was unsuccessful. In this paper we shall modify the approach of Fisher et al. by considering the "blocking" model7 for interstitial solid solutions, based on concept due to Speiser and Spretnak,' in which a repulsive potential exists between interstitial solute atoms in the solvent lattice, causing a certain number of interstitial sites to be "blocked" from occupancy by further solute atoms. We shall thus be able to describe the intimate relationship between the composition dependence of carbon diffusivity, a kinetic phenomenon, and the composition dependence of carbon activity in austenite. THEORY Consider for convenience one-dimensional interstitial diffusion in an fcc lattice in the [loo] direction. Fig. 1. Assume that solute atoms occupy octahedral sites only.7,9'10 These octahedral sites are located on {lOO} planes a/2Å apart. A solute atom, A, occupying an octahedral site on a {100 } plane denoted by 2, has twelve nearest-neighbor octahedral sites: four on plane 1, four on plane 2, and four on plane 3. Diffusion occurs when there is a net flux of solute atoms, through an imaginary plane shown with dashed lines, from plane 2 to plane 3. Fisher et al6. use the concept of activated complexes, as given in the theory of absolute reaction rates." They show that the number of solute atoms per cubic centimeter per second which pc — Fig. 1-Diagram showing the arrangement of octahedral sites (x) in the fcc lattice. pass in the direction of diffusion from activated to new interstitial position is: ?where C is the concentration of the solute in atoms per cubic centimeter, l/m + is the fraction of new interstitial positions corresponding to motion in the forward diffusion direction (transmission coefficient), ?F* is the free-energy difference between the activated complex and the reactants when each is in its standard state at the temperature of the reaction (independent of temperature and composition in the case of carbon in austenite), y is the activity coefficient of the solute species, and, finally, ym is the activity coefficient of the activated complex (assumed constant). The flux of atoms moving in the forward direction through an area of 1 sq cm perpendicular to the direction of diffusion is therefore: m+ Ym l ' atoms per second where is the distance between planes. The blocking model states that a nearest-neighbor octahedral site of a given solute atom has a probability, f, of being inaccessible to other solute atoms. The number of available sites for diffusion on a given plane will, therefore, depend on f, which is constant, and Nu, the number of solute atoms on that plane. The effect is to have more available sites in the diffusion direction, thereby increasing the net flux of solute atoms. This is reflected in the transmission coefficient, l/m. To calculate the transmission coefficient for solute

Jan 1, 1970

By David Hartley

United States Steel Corporation Minntac Mine is located at Mt. Iron, Minnesota, on the Mesabi Iron Range. The taconite pit is two miles long by a mile wide, with a maximum depth of 170 feet. This paper will deal with the radio remote control of locomotives engaged in the railroad haulage of crude ore and waste rock at this property.

Jan 1, 1970

By P. Niessen, S. J. Bercovici

RECENTLY Aust et al.&apos; proposed a model of non-equilibrium grain boundary segregation based on a vacancy gradient induced uphill diffusion process of solute to grain boundaries. According to their proposal, solute atoms which are attracted to vacancies would, during the cooling of a sample, migrate with vacancies toward grain boundaries (vacancy sinks) and thereby enhance the solute concentration in boundary regions. For solute atoms which are not attracted to vacancies no such boundary solute enrichment would be expected. These concepts were given experimental support by boundary and bulk mi-crohardness measurements of various thermally treated dilute zinc and lead alloys and also doped aluminum oxide. The underlying assumption in their work was that solute enrichment in boundary regions is indicated by higher microhardness values. From thermodynamic considerations1&apos;2 it appears that the solid-liquid solute distribution coefficient (K), defined as the concentration of solute in the solid to the concentration of solute in the liquid at equilibrium, indicates whether attractive or repulsive forces exist between vacancies and solute atoms. K < 1 indicates a solute-vacancy attractions, K > 1 indicates no, or a repulsive, vacancy-solute interaction. This note is to report on observations of different grain boundary etching phenomena in high purity zinc alloys. These phenomena appear to depend on whether a K < 1 or K > 1 solute is present. In experiments designed to measure directly the solute enrichment in grain boundary regions, samples of zone refined zinc with 0.1 at. pct solute additions were cooled from 380°C at a rate of 3°C per min. A surface layer of approximately 50 was then removed from the samples by chemical polishing. The samples&apos; surfaces were then protected by a chromating treatment such that in a subsequent etch only grain boundary regions were dissolved. The dissolved regions were approximately semicircular troughs, 10 µ in width. The grain boundaries were usually in the middle, i.e., at the bottom, of this trough. For zinc containing the K < 1 solutes cadmium and aluminum, the grain boundary was always indicated by a ridge as shown in Fig. 1. For pure zinc, and zinc containing the K > 1 solutes copper and gold, a groove at the bottom of the trough indicated the boundary position, Fig. 2., To test if these different grain boundary etching behaviors were possibly connected with the segregation process discussed above, the Zn-Cd alloy was again heated to 380°C and quenched into brine. After surface protection and etching it was found that this specimen no longer exhibited the grain boundary ridges but rather grain boundary grooves as shown in Fig. 2. It would appear, therefore, that the boundary ridge is a consequence of a process occurring during the slow cooling of the samples. From absorption spectrophotometric analysis it was found that for slowly cooled samples containing K < 1 solutes, the solute/zinc ratios of the material from the boundary trough were consistently considerably higher than the solute/zinc ratios of the bulk alloys. This boundary region solute enrichment was not observed in quenched samples. It is concluded therefore, that the boundary ridge shown in Fig. 1 is directly or indirectly connected with nonequilibrium solute segregation.

Jan 1, 1970

By T. Rigg, J. N. Stone

"The process described has been developed to utilize low-grade scrap -turnings, borings, tin cans and other types of ferrons scrap which currently has been of limited or no use in conventional steelmaking processes. If scrap of this type can be converted into high-purity iron by chemical means then there is a potential saving of several million tons of metal annually in North America.The process is chemically quite simple and consists of dissolving ferrons scrap in hydrochloric acid, followed by evaporation and crystallization of the resultant solution to yield ferrons chloride crystal.s. These crystals are dries, briquetted and converted to non sponge by reduction in hot hydrogen. The HCl produced from the reduction step. is absorbed in water and the hydrochloric acid so produced is returned to the dissolver circuit. The hydrogen produced from the initial dissolution of the scrap is used to reduce the ferrons chloride. Purity is maintained by bleeding off impure chloride solutions from the evaporator-crystallizer circuit, and converting these chlorides to oxides and HCI in a high-temperature spray roaster. The HCl produced in the roaster is absorbed in water and the hydrochloric acid returned to the dissolver."

Jan 1, 1970

By T. R. A. Davey

A Survey of current and recent research and developmental work is supplemented by predictions for processes which should be developed over the remainder of this century.

Jan 1, 1970

The Bureau of Mines analyzed the cycle of secondary gold to determine the quantity of gold not being recovered from scrap, and to identify areas for research to increase the supply of gold from scrap. Secondary gold in 1967 was estimated to be 2.4 million troy ounces; this excludes secondary gold which is recycled within consuming plants. Firms contacted included consumers using about 41 percent of the gold in 1967, And refiners that recovered about 90 percent of the secondary gold. Results of the study indicate that loss of gold is small, and refiners and consumers are accelerating programs designed to reduce recovery costs. With the increasing generation of low-grade industrial scrap, research is needed to improve present recovery techniques and to develop methods to accelerate the flow of secondary gold back to supply.

Jan 1, 1970

By George W. King

The yield strength of a dispersion-hardened W-3.8 vol pct Tho,alloy, in both the recovered and recrys-tallized condition, was investigated and cornpared with that ofrecrystallized pure tungsten over the temperature range of 325" to 2400°C. It is deduced that the Orowan mechanism is obeyed in the recrystallized alloy. In the recovered alloy, a further enhancement of the yield strength results from the retained substructure which is stable up to temperatures in excess of 2700°C. Temperature and strain rate cycling tests were also performed, and the apparent activation energy for the deformation process was derived. This activation energy, - 3 ev, for the recovered and also the recrystallized alloy was about the same as that for re crystallized pure tungsten. However, the activation volume of the recovered alloy, -10-2 cu cm, was about an order of magnitude lower than that of the recrystallized alloy or pure tungsten. This fact accounts for an enhancement oj- the temperature dependence of the yield stress of the recovered alloy. A dislocation velocity exponent of about 4 to 13 was deduced frorn the strain rate cycling tests , which is in good agreement with values reported for tungsten single crystals. VARIOUS theories have been developed to explain the enhanced yield strength of a metal containing a dispersed second phase of small hard particles. These theories are thoroughly reviewed by Kelly and Nicholson.&apos; The theoretical models can be separated into two types. The first type assumes direct interactions between moving dislocations and dispersoids. One of the most widely investigated models for this mechanism is the bowing out of dislocations between the dis-persoids and their subsequent pinching off in order to bypass the obstacles. This is the well-known Orowan mechanism.&apos; The second type is an indirect effect of the dispersion because of its ability to stabilize to high temperatures the substructure introduced by cold working. In this instance, the increment in the yield strength is expected to be inversely proportional to the square root of the subgrain diameter. In the present work, a quantitative study was made of the strengthening effect caused by a thoria dispersion in a recrystallized W-3.8 vol pct Thoz alloy over the temperature range 325" to 2400°C. The results are compared with the increment predicted for the Orowan mechanism based on the calculations by ~shb~.~ In addition, the alloy was tested in the recovered state so that any additional strengthening resulting from the substructure produced during fabrication could be measured. The respective contributions can be separated in this manner, provided that the particle size distribution of the dispersion remains the same in both the work-hardened and the recrystallized state. Particle size distribution measurements showed that this condition was met in the present work. I) EXPERIMENTAL PROCEDURES A) Material Production and Fabrication. The alloy investigated is essentially the same as that reported much earlier by ~effries,~ who also found the strength of tungsten to be improved by the thoria dispersion. The procedure for producing the alloy consisted of mechanically blending a thorium nitrate solution in proper concentration with tungsten oxide (WO3) powder, followed by hydrogen reduction to metal powder. After reduction, the dispersed second phase is present as thoria (Thoz). The pure tungsten powder used for comparison was produced in the same manner except that the thoria doping step was omitted. The powders were consolidated by cold pressing and self-resistance sintering in hydrogen. The resulting ingot had a cross section about 0.6 sq in. and a density about 93 pct of theoretical. The ingot was swaged to 0.174-in.-diam rod at temperatures varying from 1650°C initially to -1200°C near final rod sizes. Two intermediate recrystallization anneals were employed during fabrication. Analysis of the swaged rods is reported in Table I. B) Electron Microscopy Techniques. Carbon extraction rrPxcas prepared by a technique reported by ~00&apos; were used to quantitatively evaluate the thoria particle size and distribution. Electron nlicrographs of extraction replicas were taken at 20,000 times but were then enlarged two to three times in printing. The areas photographed were randomly selected. A Zeiss Particle Size Analyzer (Model TGZ3) was used to count and measure the sizes of all particles present on the print. About three thousand particles were counted in determining a distribution curve. Electron transmission microscopy was used to determine the effect of annealing on the substructures of the materials. Thin foils were produced by a two-stage thinning process. The rods were first ground on emery paper to ribbons about 10 mils thick and then a jet of 5 pct KOH was used to electrolytically reduce a portion of the cross section of the ribbon. Final perforation was achieved by immersing the specimen in a 5 pct KOH solution and electrolytically polishing at a current density of about 0.3 amp cm-&apos;. The foils were examined with a Hitachi HU-11A electron microscope. C) Tensile Testing. Tensile testing was performed in an Instron Testing Machine equipped with a radiation-type vacuum furnace which operates at about 1O"S torr at temperatures as high as 2400 °C. The same furnace was used for annealing the tensile specimens.

Jan 1, 1970

By Arcy P., D&apos Banister

Several gold-antimony geochemical anomalies were outlined near Stibnite, Idaho, using the humus sampling technique. Several hundred reconnaissance humus samples were collected and analyzed by a combination fire-assay atomic absorption method. The results partially outlined several gold-antimony anomalies and are very encouraging for further work in this part of Idaho.

Jan 1, 1970

By J. P. Batcha, J. Robert Denny

Since 1964. Newmont Mining Corp. has been engaged in a systematic research and development of computer techniques for a variety of mine planning applications. The general objective of this effort has been twofold: first, to arrive at a viable near-optimum plan for mining a particular orebody and, second, to decrease the financial investment by reducing the man-hours required for mine planning. Three major phases in the evolution of Newmont&apos;s computer techniques for mine planning are discernible. In phase one, the computer&apos;s ability to duplicate manual drafting and contour mapping was developed. Obviously, all recognized geologic characteristics had to be included, and consequently the development of computer techniques for the proper incorporation of structure, stratigraphic trends, and other geological features was a significant aspect of phase one.

Jan 1, 1970

By J. Robert Denny

The impact of the computer revolution--so pervasive in some industries--has been less startling in the mining industry. Computer techniques have been used successfully to provide drill hole calculations, contour maps, and a variety of conventional maintenance scheduling, and accounting applications. But it is our experience that the real economic payoffs lie in the engineering application of computers to mine planning and the use of systems engineering techniques for mine operations. Since 1964, Newmont Mining Corporation has been engaged in systematic research and development of computer techniques in a variety of mine planning applications. The general objective in using computers has been twofold: first, to arrive at a viable, near-optimum plan for mining a particular orebody, and second, to decrease the financial investment by reducing the man-hours required for mine planning. Three major phases in the evolution of these computer techniques for mine planning are discernible. In phase one, the machine capability for duplicating manual drafting and contour mapping was developed. The necessity of including all recognized geologic characteristics is obvious. Capability for properly incorporating structure, stratigraphic trends, and other geological features was a significant aspect of phase one development.

Jan 1, 1970

By R. M. S. B. Horta, W. T. Roberts, D. V. Wilson

Evaluation of results obtained by the Harris method for inverse pole figures is discussed. Two existing analyses and a new approach are compared. In the most frequently used analysis, different reflections are accorded equal weight. A second method involves area-weighting of reflections, mainly to take account of nonuniformity of Pole distribution. In the new method, reflections are weighted according to their multiplicity factors. Intensity ratios obtained from a sample of steel sheet by the three methods are compared. INVERSE pole figures offer a convenient method of depicting the proportions of material with various orientations referred to a unique specimen axis. The technique was first applied to fiber textures, but it is now frequently used as a description of texture in sheet metal, the unique axis in this case usually being the sheet normal. The Harris method&apos; for the determination of inverse pole figures has the great merit of simplicity. It suffers certain intrinsic limitations, but provided that these are borne in mind, the results allow useful conclusions to be drawn regarding the effects of texture components on certain mechanical properties. Much thought has been given to alternative methods of texture description, aimed at eliminating the ambiguity in the simpler methods.2"6 Refinements in the method of description are obtained at the price of increasing complexity, and it seems clear that a simple method, such as that of Harris, will continue to find application. The original derivation by Harris1 has been corrected by Morris7 and later by Mueller, Chernock, and Beck.2 Since the latter reference is more accessible, it is referred to more frequently than the work of Morris. Most users of the inverse pole figure method present their results on the basis of the treatment by Mueller et al., and it is the purpose of the present communication to comment on this treatment and to suggest a simple modification to the method of presentation which enhances the meaningfulness of the results. It will be convenient first to summarize the Mueller analysis as follows: The intensity Ihkl of a hkl reflection from a textured specimen is: Ihkl=CI0AL\Fhkl\2NhklPhkl [1] where C is a constant for a given sample I, is the intensity of the incident beam A is an absorption factor. With usual diffrac-tometer geometry and a flat specimen, A is inversely proportional to the density of the specimen. L is the Lorenz polarization factor Fhkl is the structure factor for the hkl reflection Nhkl is the multiplicity factor phkl is the fraction of crystals in the polycrystal-line aggregate with any particular (nkl) plane parallel to the surface. The corresponding equation for a specimen with randomly oriented grains is lR,hkl=CRl°ARL\fnkl\2Nnklk [2] the subscripts R indicating the factors that are different for the random sample, which will, in general, have a density different from that of the textured one. The intensity ratio is hkl , c A Phkl [3] IR,hkl CR AR PR The constants are eliminated by summing over all the measured reflections ^iRMi °R AR PR ljPkkl and from Eqs. [3] and [4] T IR,hkl The only unknown in Eq. [5] is Yj phkl and before this can be evaluated, it is necessary to adopt some form of normalizing procedure. Mueller et al. assume that when a large number, n, of reflections is used, the average value of p as defined by Eq. [6] below will be unity ? = £j**l3l [6] and the final result of their analysis follows: hkl Pkkl = i I&Jf~ [7] ±y* Ihkl ^ in,hki The normalizing procedure used by Mueller et al. involves an unrealistic assumption since it gives equal weight to each of the hkl reflections. Other normalizing procedures can now be examined with a view to selecting a more appropriate one. For an infinite number of reflections, the function p can be averaged over a continuous range of orientations covering the complete solid angle 4p by the integral relation: p =1 jp(a)dQ = l [8] This is the only exact procedure, but in practice a

Jan 1, 1970

By G. R. Love, C. C. Koch

The changes in superconducting properties with aging time have been studied ,for the pecipitation reaction in a Tc-30 at. pct V alloy. Superconducting critical temperature, upper critical field, and relative critical current density were determined by ac susceptibility techniques. Aging produces changes in critical temperature of both matrix and precipitate which can be rationalized by compositional effects. maximum flux pinning (critical current density) occurs at a time during aging when subgrain boundaries are completely decorated with precipitates and the subgrain centers remain precipitate -free. The particular effectiveness as barriers to flux motion of planar defects which enclose regions of low deject density is discussed. THE precipitation of a second phase can dramatically modify the superconducting properties of type I1 super-conductors. According to Livingston and Schadler1 one might expect changes in the primary, secondary, and tertiary superconducting properties of the material. Changes in matrix chemistry caused by precipitation can alter the fundamental superconducting parameters; critical temperature, Tc, and thermody-namic critical field, Hc. The concimitant changes in electron mean free path (reflected in normal state resistivity) can affect the critical fields Hc 1, IIc2, Hc3. Finally, the presence of precipitate particles may hinder the motion of flux lines and may considerably improve the current-carrying capacity in high-field superconductors. The influence of precipitation on superconducting properties has been studied in a number of systems.2 Magnetization measurements have been used to study the influence of precipitates on flux pinning in lead-base alloys by Livingston3 and Evetts et al4 In these alloys precipitates induced magnetic hysteresis and flux trapping. The amount of hysteresis increased with the volume fraction of precipitate and decreased with coarsening of the precipitate. Jn an Al-Zn alloy5 and an A1-Ag alloy6 the initial precipitate size was presumably smaller than a coherence length and coarsening increased magnetic hysteresis5 and critical current density.6 The influence of precipitation on superconducting properties has also been studied in several of the commercially interesting Ti-Nb7-10 and zr-Nb11 alloys. The maximum in critical current density for these alloys was confined to a narrow range of either isothermal aging time" or isochronal aging temperature7 during the precipitation reaction. Thus, experimental evidence and theoretical considerations suggest there is an optimum precipitate size, spacing, and density, and a critical composition with respect to the matrix for flux pinning. What these "optimum" values might be and the relative importance of each is still not clear, although a few generalizations can be made. It is generally accepted1&apos; that particle sizes smaller than the coherence length or larger than the inter-flux line spacing are poor pinning centers. In high Hc2 materials, precipitate sizes for maximum values of critical current density lie in the range of 50 to 2000Å,9,7 and there are indications that increasing dissimilarity between precipitate and matrix produces increasing pinning force.13 Because of several interesting features of the aging reaction in a Tc-30 pct V alloy, we have chosen to study the influence of precipitation on the superconducting properties of this alloy. The physical metallurgy14 and a survey of the superconducting properties" of the Tc-V alloy system have been reported. The Tc-V phase diagram is presented in Fig. 1. At 1500°C the Tc-30 pct V alloy is in the single phase 6 field. Samples quenched from the 6-phase field have a CsCl structure X-ray diffraction pattern at room temperature and it has been proposed that the 6 structure is closely related to the bcc lattice.14 When held isothermally below the eutectoid temperature, 115O°C, the 6 phase decomposes into the CsCl and hcp phases.

Jan 1, 1970

By Richard F. Hewlett

This report describes a comparison of methods for computing grade and tonnage of ore, leach, and waste material for a mined-out portion of the Silver Bell Oxide porphyry copper deposit, and these computed values are compared with the actual tonnage of these classes of material produced during mining operations. Comparisons with production records have been made by using both exploration drill-hole assays and development blast-hole assays. The polygonal method is the most accurate for this deposit, because it more closely represents the lateral mineral distribution in the deposit. This is demonstrated by plots of the total-copper assay distributions of the development blast-hole assays for a specific bench. The investigation also shows that the smaller vertical assay interval (based on a 5-foot vertical churn-drill-hole sample) yields a more accurate estimate of both grade and tonnage than the 40-foot composite assay interval (based on the average of eight 5-foot assay values). This can be attributed to the fact that selective mining within a bench can separate out much of the waste and leach material that is included as ore in the 40-foot composite assay computations.

Jan 1, 1970

By Oliver C. Fursman

The Bureau of Mines undertook this investigation to study methods of utilizing red mud residues from production of alumina from bauxite. Pilot-plant tests were conducted using Jamaican and Surinam red muds. Both the carbon-lime-soda sinter process and electric-arc smelting with coke and limestone were employed to recover iron and alumina. Alumina recoveries of 85 to 90 percent were obtained by the sinter process; although iron recovery was about 80 percent, the magnetic product was finely divided and difficult to separate from the gangue. Smelting red muds in the electric-arc furnace produced a pig iron with 98-percent recovery of iron; up to 84 percent of the A1203 was recovered by leaching the calcium aluminate slag with Na2C03 solution. A titania product assaying 96 percent TiO2 was recovered from the nonmagnetic portion of Surinam red mud sinter by extraction with H2SO4. Leached calcium aluminate slags and brown mud (from the combination Bayer process) are possible raw materials in the manufacture of portland cement.

Jan 1, 1970

By S. K. Tarby, A. E. Rathke

A series of 0.21 pci carbon steel melts was processed under conditions which sinzulated industrial vacuum degassing practices. The results indicated that the efliciency of carbon deoxidation was not significantly increased by vacuunz degassing at chamber pressures below 100 torr. The two common phenomena of vacuu?rz carbon deoxidation, i.e.,an unaccountable carbon loss and nonequilibrium deoxidation, were observed in this study. Oxygen from adsorbed and chenzically combined water of certain refractory structures was probably responsible for the unaccourttable carbon drop. The nonequzlibrium deoxida-tion phenomenon was adequalely correlated by a bubble nucleation )mechanism. Although the major limiting factor in oxygen removal from these melts contained in alumina crucibles could not be eslablished with certainty, there was some evidence that melt-refractory interactions were not the most imp-portant limiting factor. CONSIDERABLE attention has been given to the use of carbon in conjunction with vacuum degassing* as a deoxidation technique. An advantage of utilizing the reaction: for deoxidation purposes is that the reaction product is gaseous and hence can be effectively removed from the melt. The pressure dependency of Eq. [I] is illustrated by the expression for the thermodynamic equilibrium constant, K: where pco is the partial pressure of carbon monoxide, and hc and ho are, respectively, the Henrian activities of carbon and oxygen in molten steel. The thermodynamic aspects of the C-0 reaction in molten Fe-C-0 alloys have been investigated extensively. Theoretical predictions based on Eq. [2] indicate that, at the chamber pressures reached in most vacuum degassing units, carbon is the most effective deoxidizer that can be obtained. ~ornak&apos; has compared industrial values of carbon and oxygen contents with values calculated from theory, and has shown that on a commercial basis vacuum carbon deoxidation has not achieved the degree of success that is predicted from theoretical considerations of the C-0 reaction. The use of industrial units to determine the reason for this deviation is limited by economics and the difficulty in controlling critical process variables. Therefore laboratory-sized experiments in this area should yield valuable information. Investigations on vacuum carbon deoxidation have been made in experiments conducted under vacuum induction melting conditions where pressures in the low micron range, long treatment times, exposure to highly dynamic vacuum conditions, and relatively quiescent bath conditions have been maintained. Inve~ti~ators~~~ utilizing vacuum induction melting for the production of high-purity iron by carbon deoxidation have concluded that, under high vacuum conditions, melt-refractory interactions constantly supply oxygen to the melt. Thus, it has been suggested that refractory dissociation rather than the C-0 reaction establishes the lowest possible oxygen content of a melt. Thomas and Moreau4 and Bennett, Protheroe, and ward5 have studied carbon deoxidation of Fe-C alloys melted in magnesia crucibles under reduced pressures. The results of both studies differed considerably from those predicted by theory, and the limiting factor for lower oxygen contents was attributed to melt-refractory interactions. Because the refractory material used in both investigations was magnesia, no quantitative measure of crucible reaction could be made and the amount of carbon consumed during treatment was utilized as an indirect indication of the extent of crucible reaction. Studies concerned with the determination of the minimum oxygen content attainable in pure iron and Fe-C alloy material vacuum-induction-melted in various crucible materials have also been conducted."&apos; The suitability of a crucible refractory for use under vacuum conditions appears to depend upon the major refractory constituent, the amount and type of impurity oxides, and the composition of the melt. Meadowcroft and Elliott9 have presented a theoretical review of the type and extent of various refractory reactions which should be considered in vacuum refining. ~eadowcroft&apos;~ considered the vacuum degassing process to be dependent upon the "carbon boil" and has proposed that a part of the difference between the experimental and theoretical results for vacuum carbon deoxidation may be explained by the fact that the pco term in Eq. [2] is not the chamber pressure. Instead, the pressure necessary for carbon monoxide

Jan 1, 1970

By J. M. Davey

Lead-zinc sulphide ores at Mount Isa are currently treated at the rate of 180,000 long tons per 28 day period in the No. 2 Concentrator of Mount Isa Mines Limited. Prior to June 1966 lead-zinc ore was treated in part of the No. 1 Concentrator up to a rate of 70,000 long tons per period. Since 1955, two major changes in ore type being processed have occurred. Because of these changes, problems arising from treatment of the ore have altered and during the period several major changes in practice have been advocated and experimentally tested. Most of these flow sheets were developed with a view to overcoming one major problem in the ore. These were invariably abandoned as the Mount Isa lead-zinc ore contains a number of equally major problems all of which must be overcome in the treatment process. MINERALOGY The orebodies are situated in the Mount Isa Shale Group which is Proterozoic in age (Carpentarian System). The sediments consist dominantly of fine grained dolomitic, quartzo-feldspathic shales and siltstones. Specifically, the Mount Isa orebodies lie in the Urquhart shale formation which is characterised by sediments of high albite and orthoclase content denoting a large volcanic component. The Urquhart shales are approximately 3,500 feet thick and extend at least north and south of Mount Isa for 20 miles in each direction. In the area of the silver-lead-zinc orebodies the Urquhart shales are highly pyritic and have a relatively high carbon content. The

Jan 1, 1970

By Burt C. Mariacher

Two AIME sponsored symposia to be held during the year 1970 will examine copper, lead and zinc metallurgy in considerable depth. MBD and the Extractive Metallurgy Division of The Metallurgical Society will participate in both. Thus, the full field of minerals and metals processing including milling, smelting, and refining will be covered. Since these symposia hold special interest to MBD members, it was felt that a useful purpose could be served by devoting this column to a description of what has been arranged for the registrants.

Jan 1, 1970