Search Documents

By Jan Rosenkranz, Anders Sand, Lisa Malm, Nils-Johan Bolin

Within flotation technology the general trend is towards very large cells. Scale-up is usually done by postulating geometrical similarity, which implies keeping the aspect ratio constant when increasing cell volume. Consequently, the design of flotation circuits typically involves several cells of identical geometry within a bank. Using a few standard sizes in a flotation plant simplifies design, manufacturing and maintenance of the cells, but does not necessarily guarantee optimal performance and selectivity of the flotation process. Geometry parameters for a given cell volume that influence flotation cell performance include cell height, which causes changes in the hydrostatic pressure and suspension hydrodynamics, and also influences the travel distance of particle-bubble agglomerates as well as the homogeneity of the mixing. Also the thickness of the froth layer depends on the aspect ratio of the cell. The objective of this work is to gain a better understanding of material distribution and properties within a flotation cell and, based on this information, elucidate how alterations of the cell geometry can influence separation efficiency. For this purpose systematic measurements and analyses of the spatial distribution of the different phases within a 160 m3 flotation cell have been carried out with a particular focus on an industrial, low-grade copper ore beneficiation process. The concepts for sampling at different vertical and lateral positions of the flotation cell are introduced. The results from the experimental work give an understanding of internal material distribution within flotation cells. Based on the measured phase distribution and concentrations as well as particle properties at various positions within the cell, the implications for an optimized scaling and design of individual flotation cells within a flotation circuit are discussed.

Jan 1, 2016

By E. McCullough

"Fostering positive community relations is a principal tenet of sustainable development, but conflict can test even the strongest of relationships. While conflict surrounding resource development projects has the potential to be destructive, it may actually pose opportunities for partnership and collaboration when managed effectively. It is therefore not only important for mineral resource professionals to recognize the financial and social costs associated with legal disputes among project stakeholders, but also for them to prioritize resolving social conflict using alternative channels that allow for win-win outcomes. A variety of dispute prevention and resolution techniques do exist, but successful practice is not yet the norm. Here we review the sources and consequences of social conflict in the context of mining projects, and discuss typical and alternative approaches to conflict management in light of their respective benefits and drawbacks. We also suggest implementation of conflict resolution lessons into resource-related university curricula as a critical step in the continued shift of the mining industry towards sustainable development. INTRODUCTION Social conflict is a recurring phenomenon in the human experience and serves as a critical mechanism for change [1-5]. It occurs when two or more parties perceive that their needs and interests are in direct competition with each other and believe they cannot be reasonably accommodated. Conflict over mineral resource activities, particularly the distribution of benefit and risk, has become an omnipresent issue throughout the world [6-7]. Contrary to common perception, however, conflict can be a positive, transformative encounter in some instances [2, 8-11]. For this to be possible, society and its acting agents must reconsider how to address conflict. What if conflict were only a challenge to try something different? It is well-understood that the mineral industries must manage an increasingly significant volume of social conflict [12-13], which can be a costly externality impacting all of whom are involved. Conflict is commonly considered in a two-party sense, but this can deeply over-simplify the true number of stakeholders. Besides mining companies and community members, government policymakers and regulators, public interest groups, and judicial systems, to name a few, bear the social expenses of poorly-managed conflict [4, 6, 12, 14-22]. It is desirable for interested parties to participate actively in a constructive way to pursue their needs rather than contributing to adversarial relationships, operational problems, and legal costs [1, 4, 12]. Some mining companies are of course already working to develop more productive relationships with their stakeholders, but there is undoubtedly still a gap between ideal and common practices. This gap can inhibit collaboration and threaten the potential for mutually-beneficial resolutions to complex social issues [12]."

Jan 1, 2016

By A. Jordens, Y. Zhiyong

"IMBSRE, one of the largest rare earth element (REE) producers in China, produces a rare earth oxide (REO) concentrate as a by-product by floating the middlings stream from a low intensity magnetic separation step in the main iron ore processing stage. As the mine depth has increased, flowsheet changes in the main iron ore circuit have reduced the REO grade and increased the magnetite to REO ratio in the middling product used as flotation feed for the REO circuit. Extensive laboratory work was carried out and identified a new modified hydroxamic acid product, Florrea 8920, that could provide better metallurgical results over the standard hydroxamic acid used as the main collector. This paper briefly reviews the use of hydroxamates in the flotation of oxide minerals, provides detailed information on the different hydroxamates available from Florrea and then provides a case study of the successful implementation of the Florrea 8920 product in a commercial Chinese REE flotation plant. The case study consists of a one year program of pilot plant testing and industrial trials to confirm the results of laboratory tests. The implementation of the new collector resulted in an improvement in grade and recovery to 61% and 64% respectively. The new collector also provided significant economic and environmental benefits.INTRODUCTIONThe flotation of rare earth element (REE) bearing minerals is a topic which has been dominated in the English language literature by the work conducted on the Mountain Pass bastnäsite deposit (Pradip, 1981; Fuerstenau, Pradip, Khan, & Raghavan, 1982; Pradip & Fuerstenau, 1983, 1985, 2013; Fuerstenau & Pradip, 1991; Fuerstenau, Pradip, & Herrera-Urbina, 1992; Herrera-Urbina, Pradip, & Fuerstenau, 2013). By far the most important collector type used for the flotation of rare earth minerals (REM) is hydroxamates. These reagents were initially extensively described as REM collectors in the English literature by Pradip (1981) however they have been successfully applied to numerous other minerals such as: cassiterite (Sreenivas & Padmanabhan, 2002); pyrochlore (Gibson, Kelebek, Aghamirian, & Yu, 2015); hematite, chrysocolla, rhodonite, hubnerite and pyrolusite (Fuerstenau, 2005); and malachite (Lenormand, Salman, & Yoon, 1979) amongst others."

Jan 1, 2016

By Thomas Camus

"STATE OF THE ART The current situation of ground prediction in TBM is of great concern for tunnelling contractors, and the subject has been quite widely addressed over recent years, for instance by the French Eupalinos 2000 programme, which tested a variety of technological approaches. A number of interesting projects were executed, such as the SOUND and OnSITE projects, part of the German Geotechnologien programme: these projects are focused on seismics, while other techniques such as radar are not considered. Little information and even less industrial applications have been released apart from lab simulations and numerical modelling. A number of field tests in different configurations have been carried out for compression waves, but the results were often not reliable or convincing, and therefore little has been reported in open literature. The advances seem somewhat promising as far as hard rock tunnels are concerned, but ignore the problem raised by concrete lined tunnels such as those bored by a TBM in soft ground. In such tunnels, sending and receiving seismic waves reliably through the lining (and the grouting behind) is quite illusory. A careful analysis of the seismic prediction research results show that the main problem is the source which is poorly controlled and poorly coupled (for instance in concrete lined tunnels, or in approaches that use the TBM cutter head vibrations as a source). Generating waves perpendicular to the tunnel axis is also a problem: aligning with the tunnel axis makes more sense. Radar (Ground Penetrating Radar - GPR) has been used in geotechnical surveys for decades, and also for tunnel inspection. Attempts have been made at using it on a TBM (for example in Japan by Taisei) but mainly using off-the-shelf GPRs, which are not adapted to work in the specific environment of a TBM (because of its huge mass of metal, to start with). Very few results have been published, probably due to the somewhat disappointing performance of such implementations. At present, no TBM has a GPR incorporated in its cutter head that is able to predict ground characteristics while drilling. Another characteristic and drawback of most current methods is that they require dedicated periods of time during which other tunnel construction activities must be stopped. Due to the duration of such operations this leads to performing ground prediction on a weekly basis only, and therefore to a requirement for an investigation range of 100 metres approximately (in order to cover the TBM advance over the coming week). This is not achievable with boreholes made from the TBM, even less if a reasonable accuracy is required, as is usually the case."

Jan 1, 2016

By Alexandre Passos, Giorgio De Tomi, Tatiane Marin, Dennis Cremonese, Jacopo Seccatore

"In the mining industry, rock excavation is the first phase of the comminution process. Downstreamoperations such as secondary breaking, crushing and milling terminate the process, reducing the size of the grains down to the desired particle distribution. In such a cascade process, every process upstream heavily influences all the downstream operations. When rock excavation is carried out by drilling and blasting, a very economic source of energy (the explosive) is used at the utmost upstream; a more expensive source of energy (electricity) is employed for all the downstream phases. This means that managing the correct employ of the explosive energy is a form of managing the whole process, controlling the operational costs and therefore the profitability of the whole business. We simulated this cascade behavior, using as a starting point the experimental data obtained from small-scale block blasting, evaluating the influence of blasting on the grindability of the blasted material. This study showed the reduction in visible (particle size) and invisible fracturing (micro-cracking, resulting in a reduction of the Work Index WI). The particle size distribution for full-scale blasts was estimated by means of algorithm simulation, then we simulated the behavior of the comminution plant fed with the material possessing the characteristics previously estimated. All the costs (drilling, blasting, electric energy for the engines of the crushers and mill) were calculated and charted. The results show a clear curve that allows to estimate the minimum operating expenditure (OPEX) for the whole mine+plant framework. Being the WI dependent on the output on the blast, one can manage the performance and the expenditure of the whole comminution process by adjusting drilling and blasting parameters For any given mine, it is possible to perform a simulation and encounter the minimum OPEX scenario for the comminution process and managerial choices can be oriented accordingly. In a cascade productive chain as mining is, responsible strategic choices must be taken looking at the entire production framework. Compartmentalized managerial staff and budgets for separated production areas are not acceptable anymore. Somehow higher costs upstream can lead to effective decrease in costs and increase in efficiency and productivity of the processes downstream."

Jan 1, 2016

By L. Lorig

"Two types of extreme event, earthquakes and rainfall, potentially affect open pit slope stability. In the case of earthquakes, there are rather well-developed analysis procedures and acceptability criteria. The analysis procedures relate mainly to selection of the dynamic loading either through design earthquakes and/or pseudo-static seismic coefficients. The acceptance criteria are typically expressed in terms of a minimum safety factor in pseudo-static analyses. The acceptance criteria are often promulgated by governments despite the fact that no open pit slope has ever been adversely affected by an earthquake. This paper explains why open pit slopes are seemingly more resistant to dynamic loads than natural landforms, which can experience catastrophic landslides.Extreme rainfall events are much more likely to cause open pit slope problems than earthquakes. Two types of problem are common – slope erosion and slope instability. Slope erosion is often mitigated by appropriate surface water controls. Slope instability due to elevated transient water pressures is more difficult to mitigate. Analysis procedures and acceptability criteria are rare. This paper will discuss the mechanisms for rainfall-induced slope instability, as well as analysis methods. Examples will be discussed and analysis methods are proposed. IntroductionTwo types of extreme event, earthquakes and rainfall, potentially affect open pit slope stability. In the case of earthquakes, there are rather well-developed analysis procedures and acceptability criteria. The analysis procedures relate mainly to selection of the dynamic loading either through design earthquakes and/or pseudo-static seismic coefficients. The acceptance criteria are typically expressed in terms of a minimum safety factor in pseudostatic analyses. The acceptance criteria are often promulgated by governments (e.g., Peru, Chile) despite the fact that no open pit slope has ever been adversely affected by an earthquake. This paper explains why open pit slopes are seemingly more resistant to dynamic loads than natural landforms, which can experience catastrophic landslides.Extreme rainfall events are much more likely to cause open pit slope problems when compared to earthquakes. Two types of problems are common – slope erosion and slope instability. Slope erosion is often mitigated by appropriate surface water controls. Slope instability due to elevated transient water pressures is more difficult to mitigate. Analysis procedures and acceptability criteria are rare, but do exist. In Peru, for example, slopes are required by law to be designed for a 100-year storm."

Jan 1, 2016

By Josh Johnson, Stephen Tadolini, Mark Ferster, Curt Jacobs

"Stillwater Mining Company is the only U.S. producer of platinum group metals (PGMs) and the largest producer outside of South Africa and Russia. The Company controls a considerable portion of the J-M Reef and is currently developing the ""Blitz Project,"" which will provide a main haulage level, ore pass systems, backfill plants, and flow-through ventilation to increase production and ensure sustainable extraction of this critical strategic mineral. While driving two sub-parallel footwall laterals to about 8,125 m (26,000 ft) long, one of the development drifts experienced a massive fall in a geologically disturbed area created by a dike intrusion. Combinations of a void fill material (Tekseal), polyurethane injection, fore poling coupled with steel arches, and supplemental bolting allow safe and efficient advance through this geologically disturbed zone. This paper presents the details of this project.INTRODUCTIONStillwater Mining Company is the only U.S. producer of platinum group metals (PGMs) and the largest producer outside of South Africa and Russia. The Company controls a considerable portion of the J-M Reef and is currently developing the ""Blitz Project,"" which will provide a main haulage level, ore pass systems, backfill plants, and flow-through ventilation to increase production and ensure sustainable extraction of this critical strategic mineral.Tunnel Boring Machines (TBMs), shown in Figure 1, have been used extensively at both the Stillwater Mine and the East Boulder Mine to develop access to the J-M Reef. The J-M Reef is a PGMbearing reef deposit located in the Stillwater Complex near NyeMontana. The mining property and location are shown in Figure 2.The Blitz Project is named after the Blitz mining claims and is developing the Eastern extent of the J-M Reef Project., This consists of a 5.5 m (18 ft) diameter TBM drive on the SOE (1,562 m (5,000 ft) above sea level and east of the shaft collar) and a 4.7 x 4.7 m (15 x 15 ft) drill and blast heading on the 5,600E (1,750 m (5,600 ft) above sea level and east of the shaft collar). The Benbow Decline will be completed running perpendicular to the TBM by drilling and blasting methods. The TBM drift will be used for exploration drilling, ventilation, and will serve as the main haulage level. The 56E will be used for ventilation and exploration drilling. The Benbow decline will serve as the exhaust drift."

Jan 1, 2016

By K. C. Corin, M. S. Manono, J. G. Wiese

Depressants play a crucial role in the flotation of PGM bearing ores as they prevent naturally floatable gangue (NFG) from reporting to the concentrate. This action is regarded as critically important because less dilution of the concentrate means lower costs for downstream processes. However, abnormal water conditions (such as high concentrations of ions) in the flotation system can modify the selectivity of these depressants. It is well known that the existence of selected electrolytes in water can alter the behaviour of some polysaccharide depressants by enhancing their adsorption onto gangue minerals and thereby prevent naturally floatable gangue from moving into the froth phase. Concurrently these same electrolytes may enhance frothability, owing to their stabilising effect on the bubbles within the system. Plant water at various ionic strengths was investigated against depressant type and dosage in order to understand electrolyte-depressant interactive effects during the flotation of a Merensky ore, using entrainment, rate of NFG recovery, and total gangue recovery as proxies. The study showed that the rate of NFG recovery per unit mass of water decreased with increasing ionic strength at all dosages, however the total amount of gangue reporting to the concentrate increased with increasing ionic strength at all depressant dosages. Thus, this paper attempts to consider the effects of both ionic strength and depressant dosage as individual factors within flotation. It further looks to investigate whether any interactive effects exists between these two factors when considered simultaneously.

Jan 1, 2016

"1 INTRODUCTIONThe use of nondestructive testing (NDT) methods to evaluate the integrity of Augered Cast-in-Place (ACIP) and Drilled Displacement (DD) piles has been a subject of significant debate among engineers, contractors and NDT practitioners. This guideline document will illustrate the importance of reviewing all available information in conjunction with the NDT records. ACIP and DD piles have unique properties that must be considered when using a specific NDT method. Any evaluation of the integrity of an ACIP or DD pile must also include a thorough review of the detailed pile installation records and the site specific soil conditions. Long or theoretical descriptions of the methods have not been included in this publication. More detailed information about these NDT methods including their theoretical and historical backgrounds can be found in DFI’s Manual for Non Destructive Testing and Evaluation of Drilled Shafts (2004). Additional information can also be found in the more comprehensive textbook Nondestructive Testing of Deep Foundations by Hertlein and Davis (2006).1.1 PurposeThe intent of this guideline is to provide practical guidance for the proper interpretation of NDT results on ACIP and DD piles. Short descriptions of the main integrity methods available are provided along with several examples of how to use all of the information available to make sound engineering judgments about the results. This publication is a state-of-the-practice guideline to promote accurate engineering evaluations.For engineers inexperienced with NDT, these guidelines provide sufficient background information on NDT methods to help understand the limitations of the testing, assess the results presented to them, and formulate appropriate questions. This is particularly important for engineers charged with the responsibility to determine from those results what, if any, consequences there may be on the performance of the structure under construction."

Jan 1, 2016

"The content of production reports has its origins in raw measurements taken in harsh production environments. The ensuing measurement/estimation errors always affect reproducibility such that, regardless of the fact that they are balanced through statistical data reconciliation, reported numbers are simply the most probable values of inferred probability distributions. This has important implications for how metal recoveries should be monitored and reported. Indeed, in a context where many process optimisation activities are based on small improvements in recovery, there should be no doubt that inadequate handling of measurement/estimation errors can easily exaggerate or mask actual changes in process performance. However, estimates of the reproducibility of reported metal recoveries are rarely reported to plant management. This situation persists despite the fact that a code compliant metal accounting system must inform management about business risks related to metal accounting. To this extent, this paper focuses on the continuous management of reproducibility level of metal recoveries in compliance with the best practices. Sensitivity analysis of primary and secondary metal accounting models is performed to show the resulting probability distributions for metal recoveries. Some guidelines are given for designing and managing metal accounting systems capable of achieving and sustaining predefined levels for the reproducibility of metal recoveries.INTRODUCTIONEach and every mineral processing plant produces daily, weekly and monthly production reports in which metal balances for payable and penalty elements are presented. While such production reports are usually consulted in offices, underlying raw measurements are taken in harsh production environments where mechanical vibrations, humidity, corrosion and dust, to name a few, disturb measurement procedures. It is thus no surprise that several authors (Francois-Bongarcon & Gy, 2002; Gaylard, Randolph, & Wortley, 2014; Holmes, 2010; Spangenberg & Minnitt, 2014) have reported pervasive issues related to mass/sampling measurements in the context of mineral processing."

Jan 1, 2016

By A T. Spathis, M G. Wheatly

Some preliminary dynamic pressure data were obtained from several charges detonated in a tunnel situated in massive granite rock. The context of the work is the potential for desensitisation of explosives, failure of detonators, and sympathetic detonation due to the close proximity of inter-hole and inter-deck explosive charges to each other. Dynamic pressures were measured using piezoelectric gauges in water-filled 45 mm diameter holes adjacent to the charges. Some of the first arrival peak pressures were noisy, and although not fully resolved, may be due to reflections and the physical arrangement of the transducers and their size with respect to the monitoring holes. The estimated peak pressures were between 0.1 to 8.7 MPa at approximate distances of 2.8 to 0.8 m, respectively. Further work is planned with gauges that are disposable, have a higher pressure range, and can be used within a few borehole diameters rather than the piezoelectric gauges used in the present work.

Jan 1, 2016

"Sampling error and bias, especially the Increment Preparation Error (IPE), are introduced when the tool allocated to do the job fails to extract a representative sample. This is the case with chip sampling; the tool can only extract haphazard shapes of loose or fractured material and not always from within the demarcated sample area. Increment Extraction Error (IEE) and Increment Delimitation Error (IDE) could be severe, but are found to be relatively unbiased. The uncontrolled action of the sampler in discarding excess sample material after sample collection has a significant impact on the error and bias introduced with each and every extraction. A new type of bias, referred to as the ‘waste discard bias’, arises when samplers select what portion of the excess sample material to discard at the sample site. Material visually identified as waste is discarded in preference to mineralized broken ore if there is an excess of sample material. This results in a considerable error in the analytical results. The bias is proportional to the reef-waste ratio in the demarcated sample. IntroductionTwo types of ‘sampling’ are distinguished, namely sampling of particulate materials (broken ores) and sampling of solid, unbroken in situ mineralized reef. This study considers only chip- or face-sampling of in situ, goldbearing, carbon-rich conglomerates typical of the Upper Witwatersrand Supergroup and examines where components of sampling error and bias, clearly specified in the Theory of Sampling, may arise during the practice of ‘face sampling’. Many millions of face samples have been extracted from Witwatersrand-type mines using a hammer and chisel, and detailed descriptions (standard operating procedures) of how the samples should be taken have been developed by many mining companies. There is, however, no taxonomy or nomenclature for managing or reporting the different types of errors associated with chip sampling. The Theory of Sampling compiled by Pierre Gy in the early 1950s provides, comprehensive nomenclature of sampling errors that is applied to particulate sampling of ore in a lot, a stockpile, or a moving stream on a conveyor belt. The taxonomy and characteristics of sampling errors, grouped according to the sources from which they arise, and identified by Gy (1973, 1979, 1982, 1992, 1995, and 1998) are shown in Figure 1. This classification of errors is used extensively in regard to the sampling of particulate materials in the mining and minerals industry, but not in regard to chip sampling. A relatively small mass (hundreds of grams) of representative particulate material for estimating the average grade of a much larger mass (thousands of tons – the ‘lot’ in the Theory of Sampling) is extracted by the chipping or cutting of a representative rock ‘sample’ from the stope face."

Jan 1, 2016

By Olivia Perkins, Shawn Sismondi, Adrian St. John, Vicky Potts

"INTRODUCTION An inherent aspect of any tunnelling project is ground risk: how it is identified, quantified and managed throughout the various stages of a project. Early identification of these risks, such as adverse ground conditions or potential obstructions is crucial; however specific identification of all risks will inevitably be limited by the extent of the desk study, ground investigation and accuracy of as-built information available, particularly in a densely populated urban environment such as London with a long and varied history of development. It is therefore crucial to have suitable plans and procedures in place for dealing with potential ground risk scenarios if they occur during construction work to ensure the safety of the workforce and to protect nearby critical assets. A number of experiences of potential ground risk were encountered during the Sprayed Concrete Lining (SCL) works on Crossrail contract C300/410 which was constructed by a joint venture of BAM Ferrovial Kier (BFK). The C300/410 works, undertaken in the heart of London, comprised of over 2.5km of SCL tunnels for Bond Street and Tottenham Court Road Stations and the Fisher Street crossover, as well as two 6.2km TBM tunnel drives between Royal Oak and Farringdon. BFK appointed Donaldson Associates as their SCL designers for the works; together they were responsible for excavation stability up to the point of ring closure. Despite the majority of SCL tunnelling works at Bond Street and Tottenham Court Road being through the favourable medium of London clay, there remained areas of local geotechnical challenges. Some of these were expected from the outset, some became apparent as works progressed from records of other nearby excavation works, and some were only encountered during tunnel excavation. Being located in the centre of London meant that there always remained a possibility of meeting some form of obstruction from previous structures. However, identification of all potential issues prior to the commencement of the works was challenging and proved to not be entirely possible. Through a series of case studies, this paper documents incidents where obstructions or adverse ground conditions arose. These scenarios all had the potential to cause safety risks, impact the tunnel design and/or construction methods and ultimately add time and cost to the works. The paper discusses how these challenges were overcome which utilised in part, a progressive risk reduction cycle, feeding back knowledge gained at all stages of construction into the approach for undertaking the works. It also examines what could be done in future to further reduce the ground risk through early identification, communication, education and appropriate contingency measures."

Jan 1, 2016

By Xiaoxing Hu, Guibing Zheng, Yangge Zhu, Xingrong Zhang

"In China, more than 90 percent of titanium resources are reserved in vanadic titano-magnetite deposits. In this type of ore, the same elements such as Ti, Fe, Ca, Mg exist on surface of both ilmenite and titanaugite (the gangue mineral) because of isomorphism, which makes selective flotation difficult. Therefore, how to enlarge the floatability difference between these two minerals has always been a research emphasis and still needs to be studied further. In this paper, the pre-treatment methods using ultrasonic wave were proposed. The results indicate that ultrasonic treatment shows beneficial effect to enlarge the floatability difference, and the effect will be strengthened by extending the ultrasonic treatment time or increasing the ultrasonic power. The mechanism was investigated through infrared spectroscopic (FT-IR) analysis. Collector interacts with Ca and Mg which results in titanaugite flotation, after ultrasonic treatment, the dissolution of Ca and Mg is intensified, which leads to the lack of active points on mineral surface, so the floatability of titanaugite is depressed. Meanwhile, collector mainly interacts with Fe which results in ilmenite flotation, and the present of ultrasonic might promote its oxidation (Fe2+ to Fe3+), so the floatability of ilmenite after sonication is increased.INTRODUCTIONUltrasonic is the sound wave with frequency of 2 × 10-4 Hz~2 × 10-9Hz. Since the first International Symposium of Sonochemistry in 1986, the application of ultrasonic wave is more and more extensive. In researches about mining and metallurgy, various investigators have shown that intensive acoustic fields can modify the state of a mineral, leading to chemical or dispersive effects. Generally, the effect of ultrasonic vibration depends upon the nature of the mineral and also the way ultrasonic wave is applied (Celik, 1989; Ozkan, 2002). In addition, ultrasonic treatment usually plays roles of removal of reagents adsorbed layer from minerals and emulsification of flotation reagents when it is used in flotation (Nicol, Engel, & Teh, 1986; Slaczka, 1987; Djendova & Mehandj, 1992; Farmer, Collings, & Jameson, 2000; Gurpinar, Sonmez, & Bozkurt, 2004)."

Jan 1, 2016

By Ulrich Maidl, Gustavo Aguiar, Argemiro Ferreira, Marco A. Peixoto Silva, Marc Comulada

"Metro Line 5 in Sao Paulo is being constructed. This lot extends for 4,940 m with twin EPB shield tunnels under a dense and busy urban area, with an excavation diameter of 6.9 m. The tunnels run predominantly in the tertiary soils of Sao Paulo where extensive experience exists from previous EPB shield tunnel projects. However, new experience is being gained in Sao Paulo in shield tunnelling through Saprolite, the weathered product of the underlying Gneiss crystalline basement, through the resulting residual soils and in rock-soil mixed face conditions. Furthermore, experiences in difficult mixed face soil conditions with overconsolidated clay at the face in combination with loose sands at the crown under the groundwater table will be presented. Additionally, the design, operational and controlling approach followed for the shield drive at particular critical cross-sections where the shields were driven close or under buildings. INTRODUCTION Within the framework of Sao Paulo´s metro network expansion, the excavation of the shield tunnels for Metro Sao Paulo Line 5 is currently taking place. The present paper deals with the description of the most relevant features from the construction of the Line 5 – Lot 3 tunnels. The paper presents how particular challenges were dealt maximising potential of EPB shield tunnelling technology. Challenges were posed not only by the difficult boundary conditions of urban shield tunnelling, such as shield drive under buildings, but also by complex geotechnical situations. PROJECT DESCRIPTION The great urban area of São Paulo is one of the biggest cities in the world, with around 20 Million people living in the city and in the suburb area. The city faces great mobility problems and in the last years the government has been investing great amounts on the megacity´s metro expansion. The Line 5 Extension plays an important role to connect the south area to the central area of the city, with a whole extension of 11 kilometres, including 11 new stations. It is estimated that this line will transport almost 900.000 passengers/day. The first stretch of the expansion, Lot 3, consists of two single tunnels, almost 5 kilometres long each, crossing 4 stations. Figure 1 shows details of the Line 5 Expansion."

Jan 1, 2016

By J. N. Van der Merwe

"The probability of survival of coal pillars is a more rational indicator of stability than the safety factor. Over time, pillars undergo reduction in size by progressive scaling of the sidewalls. The probability of survival is therefore not constant but reduces over time. The rate of scaling can be quantified, and the reduction of the probability of survival as a function of time can therefore also be quantified. The paper describes the link between the factor of safety, probability of survival, and reduction of the probability of survival. Using the safety factor, probability of survival, and the time at which the probability of survival will reduce to 50% is proposed as a more rational method of evaluating pillar stability than the safety factor alone.IntroductionCoal pillar strength has long been the subject of research in South Africa and several other coal-producing countries. However, it began receiving serious attention only after the Coalbrook disaster in 1960. The most important outcomes of the initial investigations were the groundbreaking research by Salamon and Munro (1967) that resulted in the well-known power formula for pillar strength, and the work by Bieniawski (1969) that resulted in a linear formula for strength. The former approach was based on empirical back-analysis of failed and stable pillar cases, and the latter on in situ strength tests on large specimens.The Salamon and Munro (1967) formula has been widely used in South Africa and even adapted for application to hard rock pillars by researchers such as Hedley and Grant (1972).At the time of the initial work by Salamon and Munro, there were only 27 failed pillar cases suitable for analysis. It was not possible at the time to determine site- or seam-specific strength, and the result was a general formula for use in all seams in all mining districts. Since that time pillars have continued to fail and the database continued to grow – as of 2013, there were 85 cases in the database. Using the additional data, there have been a number of re-evaluations of the strength formula and it has also become possible to differentiate between the different mining seams and areas."

Jan 1, 2016

By Narasimha Mangadoddy, Teja Reddy Vakamalla

"Vertical hydrocyclones are very common in most of the comminution circuits. Inclined cyclones are also found for specific mineral processing applications. In this work, Computational Fluid Dynamics (CFD) technique and experiments are used to find the reasons behind the inclinations effect on hydrocyclone performance characteristics. The water and silica slurry experiments are conducted with 75 mm hydrocyclone at different inclined positions (0-600) to the vertical plane. Corresponding two-phase numerical simulations are performed with Volume of Fluid (VOF) model coupled with Large Eddy Simulation (LES) turbulence model. Multiphase simulations are carried out with Algebraic Slip Mixture model modified with lift, drag forces and Newtonian rheology model corrected with fines for various feed solids concentration. A raise in the under flow solids percentage, cut diameter and a reduction in the water split is observed with the inclination. Electrical Resistance Tomography (ERT) and High Speed Video (HSV) data is used to cross validate the inclined cyclone’s CFD air-core and solids concentration data. Predicted efficiency curves are found in a close agreement with experiments for all the inclinations. Comparison of experimental and predicted flow data clearly follows trend with the literature. Key words: Hydrocyclone, CFD, ERT, inclination, water splitINTRODUCTIONHydrocyclones are devices used to separate or classify particles based on particle size difference in the water medium. Their usage is very wide in chemical, petroleum, mineral and bio industries due to its structural simplicity, high throughput, small volume, low cost and maintenance. Cyclone mainly consists of a cylindrical section followed by a conical section attached to a single feed inlet and two product outlets named vortex finder and spigot. It works on the principle of centrifugal sedimentation. The slurry is fed tangentially to the hydrocyclone, in which larger particles are moved towards the wall and separated by centrifugal forces to the underflow. Smaller size particles follow liquid due to drag forces to the overflow. With its simple structure, the flow behavior inside the hydrocyclone is quite complex. Vertical cyclones are common in practice in most of the comminution circuits. Horizontal cyclones can be found in extreme cases which are for installation convenience rather than for process reasons. Inclined cyclones are also present for specific mineral processing applications. In coal preparation plants, dense medium cyclones are operated near to horizontal inclination of 20 degrees to allow large spigot sizes for sinks removal, self-drain of contents during shutdown. In the phosphate removal, dense medium cyclones are inclined with an angle between 0-90 degrees for better separation of ore and tailings (Liu Feng et al., 2006). Even in the clusters, hydrocyclones are mounted with an inclination around the feed distributor for uniform distribution of slurry and under flow collection. It is believed in mineral processing industry that inclined cyclones would fetch the benefit in number of ways while classifying the material by size. Gravity influences the cyclone performance through the air core size and position variations in large cyclones. It also favours the cyclone operation at coarser cut points without varying any other design and operating parameters. Minimizing fines misplacement to underflow can be achieved with inclination."

Jan 1, 2016

By Salam Moubarak, Thomas Camus

"INTRODUCTION Since the introduction, several decades ago, of the first concepts of tunnel boring machines (TBMs), the unremitting increase of mechanized and automated tasks and the reduction of manual tasks carried out by human operators have gone hand in hand with the continuous improvement of these machines. In the present state of TBMs, the replacement of worn cutting tools is a critical, tedious, and dangerous manual operation especially for earth pressure balanced (EPB) and slurry TBMs. For such pressurized TBMs, hyperbaric interventions are used. They consist in replacing the pressurized soil/mud inside the chamber with compressed air that balances the face pressure. The operators can then ""dive"" into the chamber; however, because the human body cannot naturally undergo pressure changes, they have to follow strict procedures that have been developed for subsea divers, based on decompression stops. Indeed such interventions are actually quite often performed by professional deep-sea divers. The pressurized TBMS are consequently equipped with a manlock that allows for the required compression and decompression cycles. Hyperbaric interventions increase risk to the operators and require long decompression procedures that increase the TBM idle time and reduce its efficiency. At higher pressures, over 3.5 bar (ITA Report No 10, 2011), specific equipment and special gas mixes and/or saturation techniques are recommended (Lamont, 2012). Such procedures are even more expensive and time consuming although the duration of work in the pressurized area can be very limited for health and safety reasons. Contractors are therefore increasingly interested in automating these operations to reduce the risks to human workers and improve the TBMs performance. Moreover, the demand for new, ambitious and challenging tunneling projects (very deep, high pressure boring) is ever increasing, but the supply of suitable TBMs is limited and the risk from working in the hyperbaric environments becomes increasingly unacceptable. Impact of hyperbaric interventions The UK Health & Safety Executive has analyzed the consequences of working in intermediate pressure compressed air. The retrospective study of decompression illness (DCI) indicated that at certain pressures its incidence was around 2% of all exposures. More worryingly it showed that over 20% of the exposures commonly undertaken by shift workers in tunneling (those over 1 bar pressure for 4 hours or more) resulted in DCI. It was concluded that on some contracts up to 50% of shift production workers experienced DCI at some time during the contract, a situation which was considered to be wholly unacceptable (Lamont, 2006)."

Jan 1, 2016

By Fatemeh Saeidi, Luis Marcelo Tavares, Malcolm Powell, Mohsen Yahyaei

"Understanding a single breakage mechanism is fundamental to the development of breakage testing techniques appropriate for mechanistic modelling of any breakage equipment. In the light of this insight, it is also possible to compare any two breakage events in a mechanistic manner. This paper presents a new method to compare breakage mechanisms of two-point impact with compression, different in their applied strain rates. This approach regards a single breakage event as a process affected by three sub-processes; first fracture, capture and spatial distribution of fragments. Spatial distribution is influenced by the kinetic energy of fragments and their brittleness. Using this methodology allows us to examine how each sub-process is influenced by applied strain rate and its impacts on progeny size distribution. For this purpose, two rock types of widely different strength, magnetite and silicate, were tested at various energy levels using the impact and compression mechanisms. To isolate the effect of spatial distribution of fragments, particles were forced to remain in the breakage zone. In this condition, similar progenies were generated from compression and impact mechanisms at similar energy levels. However, allowing natural distribution of fragments, coarser progeny was produced from compression of silicate. Additionally, using this approach provides a physical meaning and explanation for rock strength parameters such as A×b in the t10-Ecs relationship. INTRODUCTIONComminution models are rapidly progressing toward a destination that enables us to explain the complete physics of a breakage process as well as the properties of the ores. Eventually, they will be able to take into consideration the micro-events that take place during the comminution process (Bourgeois and Banini, 2002). Thus, considerable efforts have been made in the last few years in the area of ore breakage characterisation to comprehend and unlock a single breakage process that has been treated as a black box event in the majority of conventional methods. In this paper, an attempt is made to explain the effect of applied strain rate on the breakage properties of rock by using the knowledge that has been gained by understanding a breakage event. This is particularly important due to its application for various comminution devices that operate within a relatively broad range of speed."

Jan 1, 2016

By Terry Eldridge, Keith MacKay, David Siddle, Luke Moger

On August 4th, 2014, a breach occurred in the Perimeter Embankment of the Tailings Storage Facility (TSF) located at the Mount Polley Mine, releasing approximately 10.6 million m3 of supernatant water, 7.3 million m3 of tailings solids, 6.5 million m3 of tailings interstitial water and 0.6 million m3of construction materials. A Temporary Upstream Rockfill Berm was constructed between August 2014 and February 2015 within the area of the tailings dam failure in order to retain the remaining tailings solids during the low flows of the winter season. The Temporary Upstream Rockfill Berm was constructed as part of the initial response phase, with the primary objective to abate the flow of tailings into the receiving environment. A secondary objective of its construction was facilitating the required investigation works downstream of the tailings dam failure. The selection of the coarse grained material used in the construction of the Temporary Upstream Rockfill Berm was based on the availability of the material (timeliness of construction) and the non-water retaining design of this initial response phase. Consequently, an alternative method was required in order to prevent further loss of mine-affected water and tailings from the TSF, as well as to provide short-term contingency water storage, during high flow conditions expected in late spring. Golder Associates Ltd. designed the 2015 Freshet Management Embankment, a deep mixing cut-off wall, to meet these site requirements, which was constructed by Mount Polley Mining Corporation and Golder Construction Inc. between December 2015 and April 2015. The works included 132 soil cement panels constructed to depths of up to 27 meters. This aspect of the works was completed using an RG25S Bauer CSM rig on a 24 hour per day, 7 day per week schedule. The cut-off wall specifications included a target unconfined compressional strength (UCS) of between 1 and 2 MPa, a maximum hydraulic conductivity of 1x10-6 cm/s, and a ductility to enable the soil cement to undergo a minimum of 5% strain without a reduction in strength or increase in hydraulic conductivity. In order to control and assure the quality of the soil cement, 2553 wet grab specimens were retrieved from the fresh soil cement panels using a project-developed sampler. Four of the soil cement panels were cored with a mud-rotary drill rig and optical and acoustic televiewers were placed into the boreholes in order to log several relevant parameters, including image, texture, relative hardness, borehole-shape, and temperature.

Jan 1, 2016