Search Documents

By Zhang Libo, Li Wei, Peng Jinhui, Guo Shenghui, L. Jing

Partially stabilized zirconia ceramics (PSZ) were prepared by microwave sintering using natural baddeleyite which was obtained by flotation of baddeleyite ore as starting materials. Because of using natural baddeleyite as raw and the process producing no waste, it realized shorter process, energy savmg, environmentally-friendly and non-damage processing. In this work natural baddeleyite stabilized with 3.8wt.% CaO were sintered at 1300°C for 60min in a multi-mode 2.45GHz microwave furnace. Microwave sintering could fast heating and sintering. Besides that, microwave sintering could heat materials wholly, low the sintering temperature, improve the materials properties and save energy. X-ray spectrum displayed the product composed by the tetragonal phase and monoclinic phase that also showed the product was PSZ. Fine and uniform microstructures were observed in the product through scanning electron microscopy. PSZ which was with high density was confirmed by the method of the Archimedes technique.

Jan 1, 2011

By C. C. Jobes

Operating large face equipment, such as continuous mining machines, is one of the most basic and most dangerous elements of an underground coal mining operation. The operator usually performs cutting and tramming tasks in a restricted workspace with reduced visibility. During the execution of these tasks, operators often cannot see all of the locations needed to safely operate the continuous mining machine (CM ), which has sometimes resulted in accidents. In an effort to prevent these accidents, researchers at the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, examined the continuous mining machine operator?s current information cues, or visual attention locations, so that risk of injury relative to the task, equipment and workplace environment can be evaluated in the future. The eventual goal is to develop interventions to enhance the information cues, and thereby increase the safety and health of machine operators. This paper details the operator interview process, determination of visual attention locations (VALs) and simulation of various mining scenarios.

Jan 1, 2011

By Robert Hopler

BH Note: This price list stresses the point that the number six strength cap should be used with all high explosives. It’s interesting that duPont chose to continue to supply the lesser strength caps – but lowered the price of the #5 or #6 to be closer to that of the #4 and #3. There were imports of the lower strength caps at the time that had to be competed against, hence the price reductions. Another interesting point on this price list is the noting on the “Red Cross Explosives” page that these explosives reduce the danger incurred during the operation of thawing. As noted many times in these articles, this problem was not to be solved for about another 16 years or so.

Jan 1, 2011

By A. Golpaygan

Application of Computational Fluid Dynamics (CFD) modeling for simulation of fluid flow and combustion in industrial scale electric furnace is presented. Poor combustion efficiency, roof and/or side wall overheating, carry over to off-gas system and non-ideal radiative heat transfer to processes or cooling systems have been common limiting factors causing inadequate process performance of the furnace, operational problems, and safety hazards. This paper describes how CFD analysis can be used to obtain a better understanding of commonly observed problems associated with freeboard combustion. Examples are presented to describe using combustion CFD modeling to understand requirements to diagnose a problem with furnace design including required freeboard volume or possible roof/side wall overheating.

Jan 1, 2011

By Raymond J. Poletto

This paper describes the special problems that occur with the construction of diaphragm walls and discusses the lessons learned during the repairs of structural walls. Although diaphragm or slurry wall technology and equipment has vastly improved since its development in the late 1950?s, significant problems still occur. Key issues are repairs related to panel joints between wall panels, concrete defects associated with tremie concrete problems, leaks and other defects at tieback reservations or inserts, wall leaks within the plane of the wall and surface repairs. The paper supports the position that diaphragm walls are relatively watertight when properly constructed, but cautions that it is necessary to address potential problems in the design stage and allow for flexibility in construction so that the problems that occur can be corrected once encountered. Due to the fast track nature of most projects the time available for design, detailing and construction is limited. As a result, insufficient attention to detail by any of the responsible parties can lead to imperfections and defects in the wall. The authors describe the nature of these problems and their potential resolution based on ?lessons learned.? The timely response to wall problems is essential to the successful completion of a diaphragm wall project. Appropriate repairs have resulted in largely successful jobs starting with the World Trade Center in New York City. The authors? total 80 years of experience as the engineer of record and designer, inspector and contractor?s representative for the diaphragm wall results in a unique insight to deal with these problems.

Jan 1, 2011

By A. R. Barnes, N. Stubina

Increasingly, gold producers are forced to treat ever more refractory ores. While ores containing pyrite, arsenopyrite and carbonaceous material have been subjected to complete pressure oxidation (PDX) as the standard process for such ores, recent improvements in fluid bed roasting technologies have led to a resurgence of interest in roasting as a viable alternative. The lower capital and operating costs of roaster installations add further impetus to this trend. The Extractive Metallurgy Group at Xstrata Process Support operates four fluid bed reactors of various sizes which have been utilised on a large number of projects to treat highly refractory ores. Preliminary mineralogical modelling of both the physical and chemical aspects of the roasting process and subsequent testing under carefully controlled conditions has allowed clients to obtain gold recoveries approaching or matching those achievable by PDX. The flexibility of the units to operate in various modes- " bubbling bed", circulating bed, two stage, sub-stoichiometric and combinations of these, and the range of sample sizes accommodated, from a few kilograms to a few tons, has enabled XPS to accommodate clients with a wide variety of gold bearing refractory ores from all over the world. This paper outlines the key challenges of fluid bed roasting of refractory gold ores, describes the methodology used to design the testwork program and provides some results from select test campaigns.

Jan 1, 2011

By Isabela Leao Amaral da Silva, Felipe Perisse Duarte Lopes, Alice Barreto Bevitori, Sergio Neves Monteiro

"Jute fibers have in the past decades being investigated as possible reinforcement of polymer composites. However, information is still needed on the fiber interaction with a polymeric matrix for a complete evaluation of the capacity of load transference inside the composite. The present work investigated the interaction of jute fibers with polyester matrix by means of the critical length assessment through pullout tests. Tensile tests of polyester sockets embedded with different fiber lengths allowed the critical length to be determined and then the interface shear stress to be calculated. A relatively low interfacial strength was found, which indicates a weak adhesion between the ramie fiber and the polyester matrix. The SEM analysis of pulled out fibers corroborates this result.Introduction Natural fiber, mainly those lignocellulosic extracted from plants, have, in the past few decades, attracted the attention not only of scientists but also of industrial technologists of our society interested in their engineering applications. As it is well known, uses of natural fiber in clothes carpets, baskets, ropes and low cost construction roofing has existed from the beginning of our civilization. Today environmental and energy saving issues are motivating research works on new uses of lignocellulosic fibers in polymer composites [1-6]. Moreover, industrial application of lignocellulosic fiber composites are already in technological sectors such the automobile industry, packing and civil construction [7-9].In addition to environmental, economical and social benefits, some lignocellulosic fibers present specific properties that are comparable to those of other synthetic fiber used for polymer composite reinforcement. For instance, the specific strength (GPa.cm3/g) of curaua (1.31), sisal (0.92) and ramie (0.93) fibers, from results obtained with very thin diameters [10] are relatively closer to that of glass fiber E (1.33). Therefore, in principle, it would be technically justified to replace glass fiber, which is more expensive, toxic and represents a problem to the environment [ll], by a strong lignocellulosic fiber. However, serious drawbacks such non-uniform dimensions and heterogeneous properties [6] as well as the tendency to form aggregates during processing and incompatibility with a hydrophobic polymer matrix, reduce the potential of lignocellulosic fiber to be used as composite reinforcement [1-6]. In particular, a low interfacial strength causes a weak adhesion between the hydrophilic fiber and the polymer matrix."

Jan 1, 2011

By N. Shi, T. G. Joseph

ABSTRACT One-twentieth-scale field trials for conventional and concept dipper designs were compared to mid- and ultra-class-sized conventional dipper performance. Digging effort was used as the performance indicator for comparison. It was shown that linear relationships exist between dipper capacity, suspended hoist load, and peak hoist load. A ratio of conventional and concept dipper performance at the 1/20th scale was then evaluated to allow prediction of the performance of an ultra-class concept design using an independent ultra-class conventional dipper dataset. The outcome indicated a peak hoist requirement of 15.5% less to achieve the same production as the conventional design.

Jan 1, 2011

By Xuewei Lv, Guibao Qiu, Jiaqing Yin, Chenguang Bai

"The iron ore sinter is one of the main raw materials for the blast furnace (BF) process. In the production of iron ore sinter, the cooling speed of the sinter determines its quality. In addition, the heat recovery devices are installed in the cooling machine for energy saving. The cooling parameters like gas flow rate and the size of sinter should be optimized for getting the gas with a higher temperature and a good quality of sinter simultaneously. In this study, the commercial simulation software COMSOL was used to establish a model for simulating the cooling process of the iron ore sinter. Moreover, three different gas flow rate (1.5, 3, 5m/s) and three different diameter of sintered particles (50, 70, 100mm) were investigated with the model. As a result, in certain porosity, a higher cooling speed was achieved when smaller size or larger gas flow rate was used. And lower gas flow rate was beneficial for the heat recovery. The model could intuitively present the exchange of heat between the sinters and air, as well as the flow and temperature fields during the cooling process.IntroductionIron ore sinter plays a great role in iron and steel industry for many Asian countries such as China, Japan and India. As a part of the sintering procedure, the impact of cooling process on the quality of iron ore sinter couldn't be neglected. On the other hand, the massive iron ore sinters which were at high temperature contain extremely large amount of heat. However, it was reported that there's very few of them recovered in China with an average recovery rate of nearly 10.5% at 2004 [1]. Thus, more reasonable cooling procedure should be developed to get high quality product and heat recovery rate simultaneously."

Jan 1, 2011

By B. Westin, G. Voicu, C. Daoust

Orogenic gold deposits represent a major class of deposits that are found in various rock types of various ages. Those deposits show a strong structural control that usually complicates their interpretation at the regional and deposit scales. The Rosebel Gold district located in Surinam (South America) is hosted in a Paleoproterozoic greenstone belt of the Guiana Shield, and has been recently classified as one of those orogenic gold deposits. The gold district comprises eight distinct deposits located along three different structural trends and within different rock types. The mineralization is undefonned and shows a strong structural control characteristic of orogenic gold deposits. All the deposits of the Rosebel Gold district have been subject to a detailed structural analysis that has led to the elaboration of a new structural model for the whole gold district, which is now differing considerably from the previous models. This characterization had direct implications at three different scales. 1- While the older models were considering some areas of the property as gold-barren, the new structural model has led to recent exploration campaigns which have revealed positive results. 2- At the deposit scale, the comprehension of the various vein systems and of the folding of the host rocks has helped the establishment of optimized drilling campaigns. 3- At the mining scale, the comprehension of the architecture of the veins helps for the elaboration of optimized mining method. This study thus shows that the structural analysis of orogenic gold deposits is critical, and should be a priority for exploration and production in any mine.

Jan 1, 2011

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers In their Resource Development Navigation Study, the U.S. Bureau of Mines (Bureau) examined the potential for mineral development near ten Alaska port sites. This report presents the results for the first three sites: Bethel, Kivalina (Red Dog), and Omalik Lagoon. The mineral deposits near Bethel are primarily gold and mercury; the nearest deposit being 55 mites away. Because of the expense of constructing and maintaining a road over the poorly drained lowlands, the potential of Bethel as a port site in the near-term is considered to be low. The Kivalina site currently serves the Red Dog mine and has the potential to handle material for similar deposits in the area. Results from a lead-zinc mine model indicate that potential for additional mine development exists in the area. Coal is the major deposit type found near the Omalik Lagoon site. Due to environmental constraints, development of a large-scale mine producing coal for export is considered unlikely. A small-scale coal mine model was used to examine the feasibility of producing coal for regional use. This alternative may be feasible but would require conversion of heating/generating equipment in the area.

Jan 1, 2011

By A. Saki, P. Gebski, W. Ying

Industrial smelting furnaces are subjected to significant structural changes and deterioration caused by the conditions under which they operate. The current methods for the structural assessment of furnaces include visual inspections, analysis of thermal data, acousto ultrasonic-echo (AU-E) of the refractory lining and surveying of the key structural elements. Acoustic Emission (AE) non-destructive testing (NDT) technique has proven its capabilities for continuous monitoring of industrial installations and structures. Recently, Hatch Ltd. has been successful in applying acoustic emission for monitoring furnace tapblocks, and expanding the scope of the acoustic emission monitoring to the structural integrity of the entire furnace. The capability of detecting emissions related to the fracture development in the furnace shell, movement of the refractory, electrode arcing, combined with efficient source location algorithms makes an acoustic emission system a comprehensive tool for the real-time furnace integrity monitoring. In this paper the concept of such state of the art system for structural integrity assessment is presented. The initial results of the acoustic emission monitoring together with data analysis techniques are discussed.

Jan 1, 2011

By Kretschmar. U. H.

Fieldwork in the Meguma of Nova Scotia and Archean equivalents shows that bedding-parallel quartz lode gold veins (LVs) commonly occur at the top of graded elastic sequences. We define a "gold cycle" (GC) by analogy with Bouma turbidites and show that most "shear zones" and "lamprophyres" correspond to the upper pelagic-pelitic (E) division. We describe GCs from Archean Chester Twp, ON; Elmhirst, ON; Bourlamaque, QC; "intrusions" and interpret them as crystal tuffs and tuff-breccias. Extensive early Archean pyroclastic volcanism is implied: the genesis of trondjhemite-tonalite-granodiorite (TTG) rocks must be re-examined. The geopetal nature and asymmetric alteration of LVs indicates genesis from sea-floor hydrothermal vents. Textures suggest that often quartz was deposited as a gel. Vent geometry (fracture, point source or diffuse seep), bottom topography and vent spacing is reflected in wade-thickness plots. GC facing directions survive metamorphism. The Bourlamaque batholith was a flat-lying sheet of quartz-feldspar-hornblende crystal tuff, and isoclinal folding has repeated one or more gold-bearing horizons. Syngenesis clarifies and simplifies LV formation with major implications for models. Exploration becomes more cost-effective. Basin analysis, whole rock geochemistry, ore lens geometry and vent spacing can be used.

Jan 1, 2011

Barrick Gold Corporation is the gold industry leader, with 25 operating mines and a pipeline of large, long-life projects located across five continents, in addition to large land positions on some of the most prolific mineral districts. Barrick's high level of commitment to sustainable economic development and environmental stewardship was recognized by Dow Jones Sustainability Index (DJSI) - World, for the third consecutive year in 2010. The potential for adverse environmental effects from acid rock drainage (ARD) and metals leaching (ML) and their financial implications for Barrick are key considerations in our environmental assessment and business development processes. Barrick's membership in the International Network for Acid Prevention (INAP) reflects the importance of these issues to our business. INAP's development of the Global Acid Rock Drainage (GARD) Guide (a best practices guide for acid rock drainage prevention) provides Barrick with an important tool to assist in the assessment of environmental and financial risks from ARD and ML associated with our planned and ongoing mining operations (INAP, 2009). In this paper we will discuss how Barrick incorporates the GARDGuide and its principles for ARD and ML prediction and prevention in our business development processes and the management of our operations. The GARDGuide serves as a key reference for our project environmental assessments and as a common link between our projects and operations management, consulting specialists, permitting and regulatory authorities and the public. We will discuss how the GARDGuide is being "syndicated" throughout Barrick as a standard of practice and present a case study of how it was used in a recent Barrick Business Development Project.

Jan 1, 2011

In this paper, response surface methodology was applied to optimize the experimental conditions for the wet grinding of synthetic rutile. The effects of parameters such as rotation speed, solids concentration and duration of grinding on grinding efficiency were systematically investigated and the process conditions were optimized, using a nonlinear regression model based on central composite design. The statistical analysis of the results showed that in the range studied, the grinding efficiency of synthetic rutile was significantly affected by the rotation speed of the conical ball mill. According to results from analysis of variance, the value of the determination coefficient (R2=0.9989) indicates that the predicted values are found to be in good agreement with experimental values. The optimized experimental conditions were as follows: a rotation speed of 350 rpm, a solids concentration of 27.31% and a grinding time of 50.31 min, respectively. Under optimum conditions, the predicted grinding efficiency of 94.79% is obtained. The experimental values from the validation experiments were well within the predicted value of the model.

Jan 1, 2011

Refractory copper ores (CROs) in central Africa contain copper minerals that are locked up in a micacious solid matrix or associated with carbonate, sulfide and phosphate minerals. Several researchers have reported that the recovery of copper from CRO material by an acid-leaching process is not economically feasible, due to the presence of excess gangue-acid-consuming minerals such as calcites, dolomite, asbolane and iron oxides. Since the proportion of acid-insoluble copper (CuS) is about 28% of total copper and total free sulfur is extremely small, sulfide flotation was considered unfavorable. Consequently, hundreds of millions of tons of CRO material have been stockpiled specifically at the Nchanga Mine of Zambia. In terms of copper distribution in CRO material, a significant portion of total copper exists as carbonates (39%) and oxides (17%), while 28% of the copper is acid-insoluble (CuS). The rest of the copper is in the form of carbonates (16%) and (hydr) oxides (17%). This means that only about 72% of total copper is recoverable through the non-oxidative acid-leaching process. In this study, batch leach tests were performed on CRO solids (d95 = 95%) to establish the gangue acid consumption values at different feed pH values and to evaluate the leaching characteristics of copper, manganese and iron within the CRO material. Subsequently, continuous leach tests were performed on CRO solids (106 um, 80% passing) using optimum leach conditions derived from batch tests. This paper aims to show that sustainable copper recovery can be achieved by selecting leaching conditions whereby gangue acid consumption (GAC) values become significantly small and the final concentration of manganese and iron in the leach solution are appreciably low.

Jan 1, 2011

By K. R. Griffin

Explosions in underground coal mines have been a serious safety concern since the advent of mining; despite significant technological advances, they are still occurring. Parameters such as barometric pressure, geological changes, and changes in ventilation can contribute to an explosion. These factors can be monitored with available and developing technologies to create algorithms that predict when explosions are more likely to occur. This paper reviews current underground atmospheric monitoring systems and related regulations around the world. In addition, suggestions for improvement and implications for explosion prevention are discussed.

Jan 1, 2011

By Min Chen, Zhen Tian, Hongxu Cui

"The effects of adjusting technology on the phosphorous enrichment in converter slag were investigated. The results showed that the grain size of 2CaO·SiO2 with high phosphorus containing content increased slightly with the decreasing of cooling rate, and the proper cooling rate was confirmed to be about l.0°C.min-1. Moreover, the morphology of the phosphorus-rich phase of 2CaO·SiO2-3CaO·P2O 5 was changed from granular for the higher basicity of converter slag to the coexistence of granular shape and rod-like for the lower basicity of adjusted slag. With the addition of adjusting agent such as SiO2 to lower the basicity of converter slag, the phosphorus in converter slag could be transferred into 2CaO·Si02 phase effectively, and P2O 5 content in high phosphorus containing phase reached to above 30%.IntroductionThe yield of converter slag is very large in China, but most of the slag is stacked usually after the separation of iron, which not only takes up a lot of land, but also affects the ecological environment seriously. Therefore, improving the comprehensive utilization and value-added products of converter slag is of great significance to recycle the steelmaking slag[l-3]. On the other hand, the refining of hot metal with high phosphorous content is an unavoidable problem with the decreasing of high grade iron ore, and as a result, more amounts of high phosphorus containing steelmaking slag are produced. However, the current recycle of converter slag is more focused on the emission reduction and reuse of steelmaking slag inside the iron and steelmaking process without considering the recycle of phosphorous resources[4-6]. At the same time, the development and utilization of phosphate ore as a strategic resource is drawing more and more attention, but the phosphate ore in China is mostly low grade and significant amounts of tailings are produced which is harmful to the environment. Therefore, it is important to separate phosphorous resources in steelmaking slag which can be used as phosphate ore for fertilizer material[7-9].Literature studies showed that most of the phosphorus in steelmaking slag existing as 2CaO·SiO2-3CaO·P2O 5 solid solution phase in 2CaO·SiO2 particle. The P2O 5 content in the phosphorus containing phase is very low due to the fact that the basicity of converter slag is usually high and the precipitated amounts of 2CaO·SiO2 particles during cooling are very large, resulting in the fact that the P2O 5 contents in 2CaO·SiO2-3CaO·P2O 5 solid solution phase are much lower which is impossible to be used as phosphorous resources instead of phosphate ore. Thus, the enrichment of phosphorus in steelmaking slag is need[ 10-14]."

Jan 1, 2011

By D. Preece

The mining and oil industry employs techniques such as geologic mapping, core drilling and electromagnetic and potential field techniques to explore for new deposits. Since new discoveries of major near-surface ore bodies are becoming progressively rare and since traditional exploration methods are unable to resolve ore bodies deeper than about 500m, high-resolution seismic reflection techniques show great potential for exploration to much greater depths down to almost 3km.

Jan 1, 2011

By Xueyi Guo

The total production of nonferrous metals in China is 31.35 million tons in 2010, which ranks first in the world for the past ten years. Large quantities of solid wastes including slag, residue, ash, and dust are produced every year in the production of nonferrous metals. These secondary resources are renewable, not only contain abundant valuable metals which can be recycled by metallurgical processing, but also could eliminate the pollution to the environment. In this paper, the status quo of the main nonferrous metals recycling in metallurgical industries in China was summarized, and the future development of waste processing and resource recycling was prospected.

Jan 1, 2011