Search Documents

By T QUINLAN

A resource estimate uses data obtained by sampling an orebody. An example is described in which a random drilling pattern did not provide a representative set of assays, and the estimated resource was significantly less than the mine production. It is believed that a better estimate would have been made if the exploration holes had been drilled on a regular grid.

Jan 1, 1992

By W. D. Bensema, J. W. Adams, W. W. Scott, H. Dobroski

Measurements of the absolute value of electromagnetic noise and attenuation along a hoist rope were made in an operating hard-rock mine, Lucky Friday Mine, located near Wallace, Idaho. Spectra of electromagnetic noise generated by various pieces of equipment, spectra of specific noise signals at various depths, and noise and attenuation on the 4250 foot (1295 meter) hoist, were measured. Three techniques were used to make the measurements. First, noise was measured over the en- tire electromagnetic spectrum of interest for brief time periods. Data were recorded using broadband analog magnetic tape for later transformation to spectral plots. Second, noise amplitudes were recorded at several discrete frequencies for a sufficient amount of time to provide data for amplitude probability distributions. A third technique gave attenuation data through the direct measurement of field strength at various depths. The specific measured results are given in a number of spectral plots, amplitude probability distribution plots and amplitude curves as a function of depth.

Jan 10, 1974

By A. V. Z. Brink

Rock engineering risk is defined in this paper as a function of the potential ground motion; the vulnerability of the workplace; exposure of people; and a general term – quality of information. The paper describes the development of prototype software that is a combination between an expert system approach for determining overall risk assessment, a risk control recommendation and a basic GIS (Graphic Information System) approach for graphically overlying input parameters and the output risk. The expert system uses a Bayesian probabilistic approach to combine various workplace-related information, a quantified seismological environment and the exposure of underground staff to provide an overall RE risk rating. The risk assessment is dynamic in that it is recalculated each time that any of the input parameters change, for example each time a seismic event is recorded in the area of interest. The code was tested on a data set from Savuka Gold. As risk assessment is not an absolute prediction of a specific outcome, it is therefore not possible to relate to individual case studies and the reliability of this method would only be determined after an extensive period of use with appropiate back-analysis. Le risque dans le génie minier est défini dans cette étude comme une fonction du mouvement potentiel de terrain ; la vulnérabilité du lieu de travail ; l’exposition des personnes ; et un terme général – la qualité de l’information. L’étude présente décrit le développement d’un logiciel prototype qui est une combinaison entre une démarche de système expert pour déterminer une évaluation générale du risque, une recommandation pour le contrôle du risque, et une démarche de SIG (Système d’Information Géographique) pour superposer graphiquement les paramètres d’entrée et le risque de sortie. Le système expert utilise une méthode de probabilité bayésienne pour combiner des informations variées sur le lieu de travail, des données quantifiées sur l’environnement sismique, et l’exposition du personnel travaillant sous terre, pour finalement produire un classement général de risque minier (RE). L’évaluation du risque est dynamique en ce sens qu’elle est recalculée à chaque fois qu’un des paramètres d’entrée change, par exemple à chaque fois qu’un évènement sismique est enregistré dans la région. Le code fut testé sur un ensemble de données obtenues de Savuka Gold. Comme l’évaluation du risque ne constitue pas une prédiction absolue d’un résultat spécifique, elle est par conséquent difficile à rattacher à des cas individuels et la validité de cette méthode ne pourrait être déterminée qu’après une longue période d’utilisation avec analyse rétrospective appropriée. Das Gesteinstechnikrisiko wird in dieser Arbeit als Funktion einer möglichen Bodenbewegung definiert; die Anfaälligkeit des Arbeitsplatzes; das Ausgesetztsein der Belegschaft; und ein genreller Begriff - Qualität der Informationen. Das Papier beschreibt die Entwicklung einer Prototyp-Software, die eine Kombination zwischen einem Expertensystemzugang für die Bestimmung der gesamten Risikobeurteilung ist, eine Empfehlung zur Risikokontrolle und eines fundamentalen GIS (graphisches Informationssystem) Zuganges für graphisch darüberliegende Eingangsparameter und das Outputrisiko. Das Expertensystem verwendet eine bayesische Wahrscheinlichkeitsannäherung, um verschiedene mit dem Arbeitsplatz in Verbindung stehende Informationen, ein quantitativ bestimmtes seismologisches Umfeld und das Ausgesetztsein des Untertag-Personals zu kombinieren, um eine gesamte RE-Risikobewertung zur Verfügung zu stellen. Die Risikobeurteilung ist insoferne dynamisch,daß sie stets nachkalkuliert wird wenn sich irgendeiner der Eingangsparameter ändert, z.B. jedesmal wenn ein seismischer Fall im Interessensbereich aufgezeichnet wird. Der Code wurde auf einem Datenbestand von Savuka Gold geprüft. Da die Risikobeurteilung nicht eine absolute Vorhersage eines spezifischen Resultates ist, es ist folglich nicht möglich, sich auf einzelne Fallstudien zu beziehen und die Zuverlässigkeit dieser Methode könnte nur nach einer umfangreichen Benutzungsdauer mit geeigneter Postanalyse bestimmt werden.

Jan 1, 2003

By Steve Dillingham

The horrific events surrounding September 11th left Americans with a feeling of sudden helplessness...the shock of being unprepared and powerless. From this tragedy, we can understand the need to prepare for the unexpected, and can apply this hard lesson into operational planning for those involved in the commercical explosives industry.

Jan 1, 2003

By R. A. Haney, S. J. Gigliotti

Over the past ten years, analysis of the acceptability of face ventilation systems has been based on numerical criteria rather than solely a study of air flow and methane patterns in the face area. This type of analysis has become possible primarily because of the instrumentation and mathematical models developed by the Ventilation Division, Pittsburgh Health Technology Center, Mine Safety and Health Administration (MSHA). To properly use these mathematical models, large amounts of methane and airflow data must be collected in the face area during mining activities. To supplement underground testing of face ventilation systems, a full scale model of a face area was built. This model includes a full scale model continuous miner, a face ventilation system, a gas release system, and a remote methane detection system. The remote methane detection system consists of an array of twelve methane sensors located throughout the face area. Data from the sensors are transmitted to strip chart recorders. Methane, air quantity, and other data collected during a test are entered into a computer for analysis. This paper presents the data entry system, the models used for data analysis, the test results, and the application of these results to a face ventilation system.

Jan 1, 1983

By H. R. Wenk

This paper describes a workshop on deformation mechanisms and texture development in rocks. Empahsis is on relating macroscopic mechanical properties with microscopic structures and the methods of their quantitative analysis.

Jan 1, 1982

By A. J. Griest, J. C. Danko

IN the course of vacuum evaporation experiments, sublimation figures were observed on the surface of a pure nickel specimen. A cubic figure, typical of those observed on this specimen, is illustrated

Jan 1, 1957

By Jr. Arcand

Canadian Economy ? Getting Results ???? A stronger Canadian economy ???? National debt cut ???? Taxes reduced, tax-free savings account, support for manufacturing sector ???? Assisting with infrastructure Aboriginal issues affect all Canadians ???? Aboriginal prosperity is in everyone?s interest ???? Conditions for Aboriginal success include: - Indian residential school settlement - resolving outstanding specific claims

May 1, 2008

By Auguste J. Rosh

The use of titaniferous ores in the blast-furnace has been the subject of much controversy for many years. Divers objections have been raised against them, and, for one cause or another, the verdict

Jan 1, 1893

Accident control has been a pre occupation of progressive industrial and mining companies for many years but few have attempted more than direct injury control. In recent years, particularly in North America, analyses of accident costs have shown that material damage resulting from accidents is usually of greater economic significance than injuries and this has led to the concept of loss control. Loss control is an attempt to take the emphasis off injury prevention and to concentrate on the basic factors which affect both the health of the individual and of the company. The deterrent to greater acceptance of this philosophy has been the apparent diffi- culties of implementing a loss control programme but Associated Minerals Consolidated Limited has adopted a simple approach. It has had a minimum disturbing effect on normal operations because existing systems have been modified to provide the new information required. It is suggested that the programme outlined is applicable to other mining ventures and is a practical method of providing benefits for both the company and its employees.

Jan 1, 1975

By Letz H

An investigation of earthquake hazard in Papua New Guinea (PNG) by a yearly extreme magnitude method using the magnitude 7 earthquake record since 1900 shows that the Bougain-ville Island seismic zone is by far the most active, followed by the New Britain and northern mainland PNG regions. Return period for magnitude 7.0 earthquakes occurring in normalized 10,000km2 areas of the Bougainville Island, New Britain, Huon, West Bismarck, North Sepik and Ramu seismic zones is 37, 60, 81, 88, 125 and 125 years respectively. These areas are much more active than the California Seismic Zone 4 region including the San Andreas Fault, which has a normalized magnitude 7.0 return period of 299 years, calcul-ated here by the same method.Only southern PNG, including the Papuan Fold Belt and most of the Bismarck Sea, are less active than California Zone 4. The Papuan Fold Belt is only marginally less active than California Zone 4, but more active than the State of California taken as a whole.

Jan 1, 1994

The Kundana underground narrow vein gold mine had a recent history of large and damaging seismic events. Following a period of seismic events on 30 July 2001, in which nine miners were temporarily entrapped at depth due to falls of ground in several parts of the decline, the mine operation was required to develop a seismic management system to mitigate seismic risk to the operation. A micro seismic systems and boundary element modelling of mine sequence highlighted large-scale footwall faults and the mining of gold bearing shear veins to be focal structures for seismic energy release between depths of 300 m to the base of mining at 650 m. The integration of seismic data, identification of geological structures and mapping of zones of failed rockmass led to the successful generation of a non linear boundary element model and a seismic hazard strategy. This enabled mine sequences to be assessed daily, monthly and periodically for potential seismic hazards and therefore assigned both economic and personnel risks for the recovery of the ore reserve at the Kundana Underground Operation.

Jan 1, 2005

By J Walasiak

In the climate planning of mines and tunnelling with anticipated poor climatic conditions, and especially in case of longer working shifts, the main question is whether it can be reliably prevented that certain climatic limits laid down be exceeded. Working at high temperature and/or humidity can lead to reduced human working energy û a very important economic aspect û and to a risky lack of concentration on the part of the miners or to heat collapse and extremely dangerous heat stroke. With the Deutsche Montan Technologie GmbH (DMT) climate prediction programs, both the dry and the extremely significant humid heat transfer can be calculated. This is due to the high planning reliability involved. With the help of these climate prediction programs it is already possible to determine the anticipated climatic values for the operation phase as early as the planning stage of new ore or coal fields or of tunnel construction projects and to design the optimum air cooling system for every underground project with due regard to technical and economic aspects.

Jan 1, 2005

Discounted cash flow (DCF) methods are well suited and recommended as a primary valuation method for mineral assets for which there are at least indicated resources and some form of feasibility study containing engineering, production and capital and operating cost data. DCF methods are also applicable as a secondary or check valuation method for exploration properties for which no technical study has been prepared. For projects where little or no engineering, production and/or cost data is available, the process of formulating a project concept by specialists who do not possess experience and expertise in the relevant technical faculties is totally rejected as a basis for applying DCF techniques as a primary valuation method. Such an approach runs counter to The Australasian Institute of Mining and Metallurgy (AusIMM) requirement to apply relevant expertise to specific aspects of mineral valuation. Technical and commercial inputs to mineral valuation should be reviewed by specialists who have specific expertise in the relevant disciplines, and should be tempered by the quantity and quality of technical evaluation which has been undertaken and the development status of the asset.

Jan 1, 1994

This paper examines the interplay between longwall support design/geometry features, operational controls and geological features on ground response. Experience from several investigations is used to demonstrate the influence of factors such as longwall support capacity and geometry, setting pressure, coal seam strength and stiffness, tip-to-face distance and hydraulic supply and control system parameters on longwall ground response. These factors are then used to outline the requirements on key controls such as retreat rate and cutting height and their influence on allowable roof convergence. The ground response curve concept as a means to provide graphical representation of longwall support and strata interaction processes is presented. The approach was developed to address the requirement for a practical longwall support evaluation and selection tool that can take account of support load influences such as changes in roof geology or cover depth. An example of the comparison between single pass longwall and top coal caving in a thick seam environment is given to demonstrate the influence of the various factors discussed.

Jan 1, 2005

By J. A. Chermak, D. D. Runnells

Sulfide-bearing waste rock, ore and tailings have the potential for generating acid rock drainage (ARD) when exposed to an oxidizing environment. The possibility exists of utilizing the acid produced to react with lime and/or limestone to form a self-sealing cap on the reactive waste rock and tailings. Laboratory column experiments were conducted using acid-generating waste rock with a surface amendment of limestone and/or lime. Artificial rainwater was introduced and allowed to drain through the columns. Results demonstrated that the limestone and lime reacted with the acidic rock, resulting in the precipitation of a hardpan layer of gypsum and amorphous iron oxyhydroxide at the surface. The hardpan layer significantly reduced the effective permeability of the column. Based on the results of this study, it should be possible to create hardpan layers as chemical caps to significantly reduce the infiltration of rainwater and snowmelt into acidic waste rock or tailings material in the field. Unlike traditional capping methods, e.g., clay and high-density polyethylene (HDPE) covers, chemical caps should be self-healing.

Jan 1, 1998

By Mingming Zhang

This paper describes the aluminum electrowinning in a batch recirculation cell system using 1-hexyl-3-methylimidazolium chloride and aluminum chloride (ionic liquids) as electrolyte at low temperatures. The technique proposed to deposit aluminum from ionic liquid electrolyte was a three-component electrolytic cell system. Ionic liquid electrolyte was circulated between electrolytic cell and electrolyte reservoir by ceramic piston pump. Two different anodes were used in the electrowinning and it was found the extruded carbon anode had better electrochemical stability and reusability. The cell performance variables studied were the current density and current efficiency as a function of aluminum ion concentration, electrolyte flow rate and applied cell voltage during batch recirculation operation. Results indicated that the current density was directly proportional to the applied cell voltage, initial electrolyte concentration and electrolyte flow rate. Under batch recirculation operation at applied voltage of 3.5 V and temperature of 80-90°C, 80-90% current efficiency of cathodic aluminum deposition can be achieved when flow rate is 20mL/min and initial concentration is 10 mol/L.

Jan 1, 2006

By Collin L. Stewart

A summary of the results of a limited subsidence monitoring program at Cyprus Amax Coal Company's Shoshone Mine No. 1 in the Hanna Basin of south central Wyoming is presented. The monitoring program was designed to meet regulatory requirements for confirmation of subsidence predictions made in the mining permit. The longwall panels were 380 ft to 600-ft wide. Mining heights varied from 11 ft to 13.5 ft. Gate road development included three-entry and two-entry head and tail gates. Overburden depth varied from 150 to 945 ft. The coal seam and overburden dip at approximately 11 degrees. The overburden is very low to low strength mudstone and carbonaceous shale with low to moderate strength, silty sandstone interbeds. Panel W/h ratios varied from subcritical to supercritical. Smax was 0.9 of the mining height. The subsidence ratio was about 0.6 for subcritical width. The draw angle on the up-dip side averaged 20 deg. The draw angle on the down-dip side averaged 12 deg.

Jan 1, 1995

By Kelly BJ, Smith GA

The recommendations of a recent American report on "Better contracting for Underground Construction" are considered in relation to Contracting practices on major Australian projects by representatives Of the "classical trilogy" - the Owner, Engineer and Contractor.

Jan 1, 1976

Since the initial development and trials of FLEXIBOLT flexible roof bolts, further comparative testing and product development has been completed as part of the changeover to this roof support system at two Australian longwall operations, Ellalong and Angus Place Collieries. Details of the practical implementation of FLEXIBOLTS at both collieries are outlined together with their impact on roadway development rate productivity. At Ellalong where fully encapsulated 2.1 m long bolts are used, the reduction in bolt density is discussed with respect to both support system design and work force acceptance. The impact of shear deformation on bolt loading is described. Bolts longer than the working height have been required at Angus Place to achieve a suitable bolt anchorage horizon. Details of the long hole drilling and the benefits of a two stage grouting procedure are outlined. Improvements in roof conditions which have resulted from the inclusion of FLEXIBOLTS into the overall roof support strategy at Angus Place are described. Their importance to the viability of the Angus Place operation is also highlighted.

Jan 1, 1994