Search Documents

By E. Vascotto, S. M. Rupprecht, H. C. Grobler

Shaft sinking survey practices in Southern African mining operations have been refined over many decades to meet the stringent accuracy, safety, and productivity demands of deep vertical excavation. However, much of this specialised knowledge remains poorly documented, and the decline in new shaft sinking projects presents a risk that these proven practices may be lost to future generations of mine surveyors. This paper reviews and synthesises current survey control methodologies employed during shaft sinking operations, with particular emphasis on the establishment and maintenance of surface and underground control networks, shaft verticality control, and elevation transfer. Traditional techniques, such as plumb-wire plumbing systems, steady brackets, and calibrated steel shaft tapes, are discussed in detail, alongside quality control principles and common sources of error affecting coordinate transfer. The paper further examines the integration of modern technologies, including total station resections and LiDARbased laser scanning, highlighting their benefits, limitations, and practical constraints in active shaft environments. By documenting both established and emerging practices, this review aimsto preserve critical institutional knowledge, support consistent survey standards, and provide guidance for accurate spatial control throughout the shaft sinking lifecycle.

Mar 30, 2026

By Donald H. Koch

The project investigated the impacts of coal and mineral storage piles on both ground and surface water quality. The study consisted of two major tacks, Task 1 had two phases. The first phase was field investigations in which ten cons and mineral stockpile sites (5 coal, 5 mineral: phosphate, lead, copper, iron, uranium) across the country were visited to determine the actual impart of coal and mineral stockpiles on writer quality. The second phase of Task I was a series of leaching experiments in which drainage from the ten coals and minerals was controlled and monitored to survey the extent to which storage piles release toxic ions to ground and surface waters. Task IT was n review of pollution abatement techniques with three generic treatment examples applied to lead-zinc ore, eastern coal, and uranium ore stockpile leachate. Major conclusions drawn from the completion of Tasks I and II include: water quality impacts are site specific, there is n high correlation between sulfide content of u material and its solution potential, and the selection of the best treatment alternative for n specific coal or mineral storage area must be based on site-specific criteria, pilot studies on representative leachate samples, and sound engineering design.

Jan 1, 1982

By A Cooper

The current financial climate has given rise to fears that falling mineral prices and tight credit will force mining companies to cut back on production and new project development in a bid to cut costs and conserve cash. However, a prolonged squeeze on global supply can have only one result: a massive and potentially explosive demand for metals in the not-too-distant future. A resurgent global economy will also generate dramatic new demand for oil and energy, with a return to higher oil prices likely. How then should the mining industry plan for the future? In-pit crushing and conveying (IPCC) could lead the way as a partial or complete substitute for trucks. In 13 of 15 studies undertaken by Sandvik and Snowden, comparing IPCC with truck-optimised pit designs, IPCC generated operating savings ranging from US$0.18 to US$0.82 per tonne moved, compared to trucks. Trucks have higher operating, maintenance and energy costs than conveyors. New emission standards on diesel engines may make them more emission friendly but less efficient in terms of energy usage. With far more efficient energy use and cheaper operating costs per tonne moved than trucks, conveying offers an attractive alternative for the bad times ahead and into the apparent energy depleted future. When evaluating alternatives, a reasonable first step would be to conduct a scoping level study which analyses the differences in capital and operating costs between a truck and shovel operation and an IPCC solution. The study can also determine what type of IPCC is best suited to the particular mining application. The results can then be used to decide whether a more detailed study is justifiable. IPCC is a proven process that, with a fresh mindset, can make a significant improvement to mining operations. Sandvik (as an OEM with a full suite of IPCC equipment) can undertake these studies in ten working days in conjunction with Snowden or any other independent mine planner who knows how to schedule for IPCC. Because most mining industry personnel have been æborn and bredÆ on trucks and shovels û this paper focuses on some of the practical considerations necessary to make IPCC systems work that the Sandvik Technical Services Group has encountered during these studies.

Jan 1, 2009

By W. V. Kuster

The investigation described in this report is part of a survey by the Federal Bureau of Mines of the titanium resources of the United States. The purpose of this project was to study a typical coastal deposit of beach sands in the Middle Atlantic States, particularly in the area surrounding the Delmarva Peninsula. The field investigation consisted of a reconnaissance survey of the Eastern Shore of Maryland, followed by surface sampling and drilling of the sands on Assateague Island, off the Atlantic coast of Maryland. The study covered the period January-December 1957. Detailed analyses were made of 5-foot sections of eight drill holes along the Maryland section of the island. The heavy-mineral fraction of these samples was separated by sink-float tests, using acetylene bromide as the heavy liquid. The minerals comprising the heavy fraction were examined microscopically, and mineral counts were made on selected samples.

Jan 1, 1959

By R. Kramer, A. Habibi

A ventilation survey was conducted in an underground longwall trona mine. The mine is relatively shallow and categorized as a gassy mine. The ventilation system includes three intake and six exhaust shafts, and three surface axial fans ventilate the mine in a blowing configuration. Airflow quantity, pressure losses and air psychrometric characteristics were quantified, and the influence of moving cages and skips in the shaft examined. The benefits of utilizing high-accuracy digital pressure transducers and advanced psychrometers were seen when undertaking a “leapfrogging” survey to gather data needed to build a computer ventilation model. Two underground booster fans with VFDs are idle but available at the mine. The ventilation model was used to determine the optimal booster fan locations to decrease operating cost by reducing the load carried by the main fans. A leakage study was conducted to evaluate the effects on the system of additional pressure from a booster fan. The study finally prepares a future ventilation model for the next 15 years of mine operation and investigates the effect of proposed scenarios.

Jan 1, 2014

By P. T. Bloomer

Introduction Mining of the orebody of the Sullivan mine, which is owned and operated by the Consolidated Mining & Smelting Company of Canada, Limited, has reached a point where pillar extraction is rapidly becoming a major part of the operation. Very few of the larger pillars have been completely extracted; consequently, this paper contains much that is theory and expectation. Due to early mining methods and the physical characteristics of the Sullivan deposit, similar conditions may not exist in other older mines facing the problems of pillar extraction, but it is thought that the methods employed and those contemplated may be of general interest. History The Sullivan orebody, which is at Kimberley in the Fort Steele mining division of the East Kootenay district of British Columbia, was discovered in May, 1892, by Messrs. Sullivan, Smith, Cleaver, and Burchett. After passing through the hands of several owners the property was optioned in 1909, and purchased in 1910, by The Consolidated Mining and Smelting Company of Canada, Limited. Early mining was highly selective, the objective being a clean, high-grade silver-lead ore. By 1923 the difficulties of milling the very complex ore had been overcome and the first unit of a concentrator was completed with a capacity of 2,500 tons daily. Capacity was increased by stages to the present rate of 8,500 tons per day. Concentrates are shipped over the Canadian Pacific railway ? to the Company smelter at Tadanac, British Columbia, for final treatment. Approximately 45,000,000 tons of ore has been mined to date.

Jan 1, 1948

By Richard C. Enochs

In order to clearly understand our process control system it is necessary to briefly discuss the various process control systems that were considered and why we chose our particular configuration. We considered Analog Systems, Computer Supervisory Systems, Computer Setpoint Systems, Direct Digital Systems and Direct Digital with Backup Systems. Our concept of these systems is illustrated in Figure 1 through Figure 5. We chose Direct Digital Control with Manual Backup because it had the greatest flexibility, ease of implementation and cost no more than a pure Analog Control System for one control concept. There would be no increase for a Direct Digital Control with Manual Backup System if the control concept were changed, while there could be considerable additional cost with an Analog System, if the control concept were changed.

Jan 1, 1975

By Debbie Laney

DOUG HALBE: Second in our quick run-through on "Operating Ideas That Have Saved Me Some Bucks," was Debbie Laney of Rayrock Mines. Debbie apologizes. She can't be here. But she said, "Doug, don't worry. I've asked Mary Korpi to present the paper. We're both short, blond, and wear glasses. Nobody will know." [laughter] Mary, I caught it right away. You ladies can't fool us. Debbie, who wrote the paper, has spent almost her entire career in operations. She is currently metallurgical manager of Rayrock Mines in Valmy, Nevada. Mary Korpi is also a real operator (that doesn't sound right). She has been responsible for a number of operating areas at Newmont's Nevada operations, and she is currently taking a break from operations as manager of public relations/employee communications for Newmont Gold in Carlin. MARY KORPI: They told us this year at Newmont that we were going to have to work twice as hard. I had no idea it meant I would have to work for another company, too. Over the years, and many times in association with work for mid- to small-size mining companies, there have been two areas that seem to have been the focus of cost savings when looking at new facilities or new processes.

Jan 1, 1998

Filtration systems with disposable filter elements (DFEs) are used in the underground coal mining industry to control particulate matter emissions from diesel-powered permissible and nonpermissible coal mining equipment. This study was conducted in underground mine conditions to evaluate three types of high-temperature DFEs used in those filtration systems. The DFEs were evaluated for their effects on the concentrations and size distributions of diesel aerosols and concentrations of nitric oxide (NO) and nitrogen dioxide (NO2). Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. After an initial DFE degreening period, the filtration system with all three DFEs was found to be very effective at reducing total mass concentrations of aerosols in the mine air. The effectiveness of DFEs in filtering aerosol mass was found to be a function of the engine operating conditions. The efficiency of the new DFEs significantly increased with accumulation of operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on performance of the DFE elements. The effectiveness of DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for both DPFs and DFEs when the engine was operated at high-load modes than at low-load modes. Initial heating of certain DFEs resulted in visible white smoke and substantially elevated aerosol number concentrations. The effects of the DFEs on total nitrogen oxides (NOX) concentrations were found to be minor. The NO2 fraction was found to be generally lower for the DFEs than for the muffler. The engine-out NO2 fraction of the total NOX was found to be substantially higher for low-load modes than for high-load modes.

Jan 1, 2011

By Ch. D. Taylor

Past studies with blowing face ventilation systems have shown that using a machine-mounted scrubber and water sprays can reduced methane levels at the face. The current research was conducted to determine how the sprays and scrubber interact to reduce methane levels, and what spray configurations provide the best face ventilation when used with a scrubber. Testing was conducted in a ventilation test gallery designed to simulate a full-scale mine entry. In the entry, a model mining machine, equipped with a simulated dust scrubber and water spray systems, was located at the face of a 6.1 m (20 ft) box cut. Face ventilation was provided by a blowing curtain located 12.2 m (40 ft) from the face. Methane released from a manifold at the face was measured at six locations near the face to compare the ventilation effectiveness of the spray systems while operating with and without the scrubber. Airflow movement across the face was affected by the spray configuration and scrubber operation. Average face concentrations were lowest when directed sprays were used with the scrubber. Varying the direction of the scrubber exhaust affected face methane levels.

By Donald B. Buddecke

The large walking dragline has been the most commonly used overburden-stripping equipment in Texas lignite mines. These draglines, operating on the highwall side of the pit, can excavate to a depth of 45 m. Considerable overburden rehandling is required beyond 30 m and may reach 100 percent by 45m. As pit depth increases, dragline operation also becomes more complex, with two or three passes being necessary to make a cut 30 to 40 m wide. Multiseam operations also require extra passes. At pit depths greater than 45 m, the dragline must be operated also from a spoil bench. This can be difficult in the unstable alluvial deposits in which lignite occurs.

Jan 1, 1985

By Verônica Scarpini Cândido

Cimentos provindos de reações álcali-ativadas abrem novas oportunidades para o futuro, como a utilização de polímeros inorgânicos, conhecidos como geopolímeros. Estes materiais são considerados ecologicamente corretos, pois seu processo de fabricação não envolve a emissão de CO2 e é possível utilizar resíduos industriais como matéria prima. Neste trabalho, foi desenvolvido um concreto de cimento geopolimérico (CCG) e sua resistência à fadiga foi comparada com outro concreto correspondente de cimento Portland (CCP). Foram utilizados alguns parâmetros fixos na dosagem de ambos os concretos, como consumo de aglomerantes, relação água/aglomerante e teor de argamassa. O estudo foi realizado por meio de ensaios dinâmicos, avaliando os efeitos de diferentes níveis de tensões, máximas e mínimas, e frequência aplicada. Os resultados de fadiga nas diversas variações realizadas mostraram um melhor desempenho ao comportamento em fadiga do CCG em relação ao CCP. Na análise microestrutural foi observada uma melhor aderência matriz/agregado no CCG quando comparado com o CCP, o que pode explicar sua maior resistência perante a fadiga.

Oct 30, 2017

By E. M. Spokes

A.B. Rushton The work and resulting publications of the Committee on Underground Coal Mine Safety and The President's Commission on Coal were appropriate at the time of publication. The statistics cited in the publications appeared to be valid, and the actions proposed by the committee had merit. Although the actions proposed to achieve further improvements in safety may have been worthy of repeating, to associate statistics (Table 1) that are seven to eight years old with company names is bad. Statistics are readily available from the Mine Safety and Health Administration (MSHA) and are usually within three months of being up to date. A review of the most recent Coal Controlling Co. Report will reveal significant changes in the rankings. The more recent statistics should have been cited, or at least compared with those used in the article. Westmoreland Coal Co. is listed as having a 21.1 disabling injury rate for the period (1/78-12/80). The disabling injury rate for the Company for the year ending 1985 was 7.4 for the underground mines and 6.25 for the total facilities. Through March 1986, the disabling rate for the underground mines was 2.86. The management and employees of Westmoreland Coal Co. are committed to safety. The improvements achieved over the past five years attest to that commitment. We are justifiably proud of the achievement and dislike being misrepresented as in the April 1986 article. Reply by E.M. Spokes I regret that the lapse of time since the original work gives a picture of safety practice that is no longer true today. That Westmoreland has reduced its disabling injury rate by 65% to 7.4 in 1985 is most commendable, and I congratulate you for this accomplishment. It is typical of the progress sought by the National Academy of Science and National Research Council when they funded the original study and published "Toward Safer Underground Coal Mines" in 1982. If a significant number of companies do as well as Westmoreland, the report will have served its purpose. Since the paper was primarily a condensation of the original report, it would not have been appropriate to seek access to later statistics. The purpose in seeking its publication at the time of presentation was to reach those who might have missed the original report. The fact that publication was delayed has not voided that purpose and may have reminded some who were aware of the original that its recommendations still apply to improvement of underground coal mine safety.

Jan 6, 1986

By S. Jayson Ripke, Shane Hoff

Cleveland-Cliffs’ Northshore Mining Company operates a magnetic iron ore (taconite) concentrator and pelletizer in Silver Bay, MN. These are two recent cost reduction projects: 1. Rougher Magnetic Separators were upgraded throughout the concentrator; throughput and recovery were simultaneously improved. 2. Green Ball Roll Screens on one agglomeration circuit were upgraded from 3.5-inch to 2.5-inch rolls. Throughput improved by 24% from 62 to 77 LTPH. Green ball size distribution improved as an added benefit.

Jan 1, 2005

By Danielle Gonçalves Campos

Com o ensaio de RDI (Índice de Degradação sob Redução), pode-se determinar a geração de finos durante a redução da carga metálica no alto-forno, e com o RI (Índice de Redutibilidade) determina-se a capacidade do sínter em ceder oxigênio para o gás redutor. São ensaios de extrema importância, pois com o RDI é possível medir a degradação do sínter quando submetido a condições redutoras do alto-forno, e com o RI entende-se o grau de redução da carga metálica momentos antes do início de seu processo de amolecimento. Com a instalação deste forno no Laboratório de Redução da CSN, será possível correlacionar os componentes do sínter, e de outras cargas metálicas, avaliando suas influências no produto, e, consequentemente, em suas utilizações no alto-forno.

Aug 1, 2018

By Qingwei Wang

This study focused on acidic wastewater from producing sulfuric acid system in zinc smelter containing mercury 21.48mg/L, zinc 55.85mg/L, lead 38.50mg/L, copper 1.68mg/L, cadmium 10.25mg/L, As 29.86mg/L treated by biologics. The factors of pH value, the ratio of biologics to mercury, complexing time, hydrolytic time and temperature were studied in this paper. Experimental results indicated that at pH value 10, quantity of biologics to mercury ratio was 16, complexing time 30min, hydrolyzation time 20min, temperature at 40?, concentration of mercury in treated water was removed to 22.15µg/L. At same time heavy metals such as Zn, Pb, Cu, Cd, As was removed by biologics, the remained concentration in treated water was Zn 0.53mg/L, Pb 0.12mg/L, Cu 0.01mg/L, Cd low to 0.01mg/L and As 0.023mg/L. According to EDAX analysis, mercury content in complexing sediment reached 28.49% easily to recycle as raw material and low concentration of heavy metals in hydrolytic sediment easily to dispose and treat.

Jan 1, 2009

By Karinne Fernanda Menezes de Freitas

O objetivo deste estudo foi avaliar a soldabilidade do aço da classe API 5L X80 de fabricação nacional quanto ao trincamento pelo hidrogênio. Para isto, o aço foi soldado pelo processo arame tubular usando como metal de adição o arame AWS E110-MC com 1,6 mm de diâmetro e como gás de proteção a mistura 75% Argônio+25%CO2. Foram adotados quatro níveis de energia de soldagem, 0,7 kJ/mm, 1,10kJ/mm, 1,60 kJ/mm e 2,00 kJ/mm e o ensaio de soldabilidade utilizado foi o WIC. Para as quatro energia de soldagem foi constatada a presença de trincas que iniciavam na região de grãos grosseiros da ZTA (RGGZTA) e se pronunciavam para a zona fundida (ZF). A ZTA apresentou um comportamento microestrutural com presença de bainita e a ZF com predominância de ferrita acicular. A microdureza na ZF foi superior em relação às demais regiões.

Aug 8, 2018

By Marcos Vinícios da Silva Cavalcante

O processo de um forno de endurecimento de pelotas cruas tipo grelha móvel baseia-se na queima de esferas, aglomerados de minério de ferro, acomodados no interior de carros de grelha que se movimentam com certa velocidade através das zonas do forno. Neste tipo de forno as pelotas cruas são queimadas predominantemente por convecção por gases aquecidos via queimadores instalados na zona de queima. Estes gases quentes passam por entre as pelotas com uma velocidade, densidade, viscosidade e temperatura tal que garante a secagem, a sinterização e o resfriamento das pelotas enquanto são movimentadas dentro dos fornos. A permeabilidade de um leito de pelotas é uma função direta dos espaços vazios formados pelo empacotamento destes aglomerados esféricos que o compõe. Este estudo validado na linha de produção teve como objetivo relacionar os espaços vazios com alguns parâmetros de controle operacional usuais na indústria de pelotização e associá-los a qualidade física, produtividade e ao custo de produção.

Aug 16, 2017

By C M. Sennitt, M J. Spadafora

Systematic field evaluation of known gold and clay occurrences in South Korea has led to the recognition and discovery of both high and low sulphidation gold-silver epithermal systems. These are associated with Cretaceous acid-intermediate volcanic centres in the southern parts of the peninsula. The high sulphidation deposits such as Seongsan and Kohung are characterised by pervasive silica-alunite-dickite-pyrophyllite alteration with anomalous arsenic geochemical signatures. Gold mineralisation is associated with fine grained marcasite and pyrite. A low sulphidation quartz vein system observed at the Tongyoung mine comprises multistage colloform banded quartz-carbonate assemblages, with minor manganese and base metals. Gold and silver occur as electrum and tellurium minerals. Some deposits such as Gasado and Dogcheon display both high and low sulphidation alteration assemblages. Early pervasive silica-alunite-pyrophyllite alteration caps formed by acid fluids with a significant magmatic component, occur above cryptocrystalline colloform banded vein systems. The quartz vein stage hosts the precious metal mineralisation and appears to have been deposited by later neutral fluids generated in part through mixing with meteroric water.

Jan 1, 1999

Scattered north and south along a 161-km (100-mile) stretch of Interstate 80, Newmont Min¬ing Corp. owns four active mining properties in Nevada?s northern high desert ? Carlin Trend Operations, Midas, Twin Creeks and Phoenix. Among the four, there are nine openpits, five underground mines and 14 processing facilities. While gold is the predominant ore, silver and copper are also produced. And in a move to hold down energy costs, Newmont built and owns the 200-MW (net), coal-fired TS power plant. This plant provides about 65 percent of the power used for Newmont?s own operations, while the rest is sold to NV Energy, which services Nevada and northeastern California. Bringing the Phoenix Mine ? Newmont?s newest in Nevada ? on-line presented many developmental and operational challenges. Located about 19 km (12 miles) southwest of the town of Battle Mountain, the general area had been home to prospectors and other mining companies since the 1860s. But any profitability in developing the lower grade gold, copper and silver deposit at Phoenix proved elusive, with Battle Mountain Gold being the last company to make an attempt. When Newmont acquired Battle Mountain Gold and its Phoenix reserves in 2001, the lower grade of ore was not a deterrent. Newmont found Nevada-wide cost savings synergies for maximizing profit during the depressed gold market of the late 1990s. The new property was aptly renamed the Phoenix Mine, a nod to its rising from the ashes of the dreams and efforts of previous mine owners.

Jan 2, 2010