Search Documents

By S. Sinha, S. Ganguly

"In an opencast mine explosives are used for fragmentation of rock. Inefficient use of explosive energy in an opencast operation produces excessive ground vibration, which is measured by peak particle velocity (PPV). To mitigate ground vibration, it is essential to develop a model to predict PPV. At present empirical models are used. These models are based on only a few input variables, hence they fail to take into account the effects of the myriad factors that cause ground vibration. Due to lack of explicit knowledge about the complex mine blasting system the scope of application of mathematical and statistical modeling techniques is limited. The artificial neural network (ANN) technique is a learning algorithm that can remove some of these limitations and can be applied to predict PPV. In this paper an ANN model is developed for prediction of blast vibration using 248 data records collected from three coal mines with diverse geomining conditions. The correlation coefficient between measured PPV and model output was found to be 0.96 and the average error percentage 11.85. The ANN model output was compared with the output of three empirical models that are widely used for prediction of PPV. The correlation coefficient between the PPV predicted by an empirical model and measured PPV data was 0.63 and the relative error percentage 38.47. This result demonstrates the superiority of the ANN model compared to empirical blast models. By using site-specific structural discontinuities as input the model performance can be further improved. Sensitivity analysis and 3D plotting were used to gain further knowledge about blast-induced ground vibration. IntroductionIn an opencast coal mine explosives are used for fragmentation of coal and overburden. If the explosive energy is not fully utilized it causes blast-induced ground vibration, which may damage nearby structures. Ground vibration is expressed as peak particle velocity (PPV). During different stages of mine planning and operation, it is necessary to use a ground vibration prediction model for blasthole design. Selection of the modelling technique is crucial. Mathematical and statistical modelling techniques have limited application because of the lack of explicit knowledge about the complex mine blasting system. Vogiatzi (2002) highlighted the problem of multicollinearity in case of statistical modeling techniques. Mutalib et al. (2013) stated that mathematical models are unable to capture the nonlinear relationship between several blasting-related parameters due to the complexity of the model input data. However, the difficulty involved in modelling complex blast vibration problems can be removed by adopting an alternative soft computing modelling approach. One of the soft computing techniques is the artificial neural network (ANN). Ragam and Nimaje (2018) developed an ANN model for predicting PPV using six input variables. Kosti et al. (2013) stated that the conventional predictors fail to provide acceptable prediction accuracy. They showed that a neural network model with four mine blast parameters as input could make significantly more accurate on-site predictions. Sayadi et al., (2013), using a database from Teheran Cement Company limestone mines, found that a neural network resulted in maximum accuracy and minimum error. Khandelwal and Singh (2009) developed an ANN model using 150 data records from an Indian coal mine with site-specific rock characteristics and geomining setting. Khandewal and Singh (2007) built a ground vibration prediction model for a magnesite mine using four prediction variables with 20 data records. Kamali and Ataei (2010) predicted PPV in the structure of the Karoun III power plant and dam using an ANN. El Hafiz et al. (2010) evaluated ground vibration predictors using data from a single-station seismograph at a limestone quarry in Egypt."

Feb 1, 2019

By Melinda J. Hummel, Zachary T. Smith, Nathaniel Witter, Nina F. Carney

The revitalization of Pittsburgh’s historic Strip District has led to the redevelopment of existing properties and the development of new properties. At one time, the Strip was home to wholesale market products. Now, the historical warehouse buildings are being converted to multi-use residential and commercial properties. One such property, 1600 Smallman Street, consisted of 1 to 6-story connected buildings that housed night clubs, retail shops, and office space. The lower story portion of the building, on the southwest side of the property, was torn down to make room for a new 5-story- parking garage with street level retail space. The remaining 6-story-building, on the northeast, was gutted to be renovated into high-end condominiums, keeping the exterior historical building facade.

By E. P. Gustafson

Demand by precious metals explorationists for cost effective means to target subsurface geologic structures worthy of evaluation by means of drilling has led to the use of the predictor-correlator technique. To locate polarizable targets, the predictor-a localized inhomogeneity in electrical properties-is placed at various locations in the computer-simulated subsurface region, and correlated with the potential distribution observed in the field. The correlation coefficient obtained is assigned to the subsurface location. IP targets are extracted by calculating a second correlation section based on higher-frequency illumination and subtracting it from the first. The locations of correlation difference correspond to the locations of polarizable mineralization.

Jan 1, 1989

By H. N. Dunning

A comprehensive production research program, now in progress at the Petroleum Experiment Station of the Bureau of Mines at Bartlesville, Okla., includes studies of the displacement of petroleum from sand by detergent solutions. An earlier report (12)2/ presented the results of an extensive research program to determine the value of detergents as floodwater additives. This report presents later results of the detergent-testing program (13, 17). Although water-flooding methods and controls are constantly being improved to increase the production of oil from secondary-recovery operations, considerable crude oil commonly remains.in place after a water flood has been terminated. Therefore, the possibility of improving the efficiency of a waterflood by the use of detergents is of increasing interest. The effects of many substances on the efficiency of water flooding have been investigated in laboratory studies (5, 11, 13, 17, 19, 24). Of the various sub-stances tested, only surface-active agents were consistently effective in removing oil from sand. Results of laboratory studies presented in earlier reports (9, 11, 12, 13) show that many detergent solutions effectively displace petroleum from sand surfaces under varying conditions encountered in centrifuging, manual and mechanical agitation, ultrasonic vibration, and imbibition.

Jan 1, 1957

By EDGAR K. SOPER, Clarence A. Wright, DOUGLAS C. LIVINGSTON, Thomas Varley

In 1917 the Federal Bureau of Mines and the University of Idaho arranged to cooperate in an investigation looking to the improvement of mining and milling methods in the mining districts of the State of Idaho, with an especial view to the wider development of the minerul deposits and greater efficiency in the treatment of the lowgrade ores of the State. This work has been made possible lnrgely through the generosity and active assistance of the mine operators, especially certain companies in the Coeur d'Alene region. As the first step in the work under the cooperative agreement it wa.s decided to gather all data possible on the various mining districts throughout the State, both active and abandoned, in order to ascertain their potential possibilities, especial attention being paid to methods of metallurgical treatment and to the solution of the many metallurgical problems in order to effect a greater commercinl saving. With this plan in view, field work was begun in the latter part of May, 1917, and was continued during the summer. E. K. Soper, formerly professor of mining, University of Idaho, and now dean of the mining department of Oregon Agricultural • College, Corvallis, Oreg., visited the mining districts in central and southwestern Idaho and also some of those in the northern part of the St.ate. D. C. Livingston, professor of geology at the University of Idaho, Moscow, Idaho, also visited some of the mining districts in central Idaho during the summer; in addition, much valuable information he had gathered on former trips to many other districts is included in this report. Credit is also due Mr. Livingston for the maps covering the State, as well as the bibliography nt the end of each chapter. Thomas Varley, superintendent of the Seattle mining experiment station of the Bureau of Mines, spent a short time in the field, principally in the mining districts in central and . northern Idaho, and made a brief visit to the southwestern districts with Mr Soper. The field work of Mr. C. A. Wright, metallurgical engineer of the Bureau of Mines, in direct charge of the cooperative work, was chiefly in the Coeur d'Alene region. Mr. Wright visited nearly all of the mining districts in the region and devoted most of his time to studying the milling methods. The results of the investigation are set 1iorth in this bulletin. The bulletin aims to give the l9Calities of the various mining districts, and the nature of the present operations and those that have been carried on in the past. The geology is discussed only in a general way, the descriptions being intended more especially to bring out the types of ore deposits and the character of the ores, a knowledge of which is essential in determining the proper treatment of the ores. The writers do not wish to imply that all districts mentioned in this bulletin were visited during the summer of 1917, for a great deal of the material has been gathered from other reports, especially from publications of the United States Geological Survey. However, it is hoped that this report will be of help to those who are interested in mining in the State of Idaho. The plan is to continue the field work and subsequently publish the results of the investigations in much more detail, with greater emphasis given the metallurgical treatment of the ores and the problems involved.

Jan 1, 1919

By Martin Junker

This Notwithstanding all the debates on climate change and renewable energy, coal remains the world's no.1 primary energy source even in the 21st century. In 2011 alone, total output rose from 420 million t to around 6.6 billion t. Similar growth rates are also expected for the next few years. In order to meet demand, new seams are being tapped and others mined far more extensively. In most cases, this means a move from open-cast to deep mining, and extracting coal from ever greater depths. At the same time, extraction processes such as the room and pillar method are being replaced by longwall mining, which significantly increases seam yield and therefore output. The depth of extraction with new, modified mining methods is increasing rapidly around the world - in most countries, much more rapidly than the corresponding expertise. A trade in mining expertise has therefore developed alongside the coal trade proper. Germany relies on coal imports, but can export mining industry services and advanced mining equipment. Geological conditions in the Ruhr and Saar coalfields forced Germany to drive forward development of deep working for hard coal years ago. For 30 years now, Germany has been mining hard coal at depths of over 1,000 m, and excavation is now at depths up to 1,600 m. Deeper extraction and more extensive excavation posed new challenges for both miners and equipment. Intelligent logistics, modern roadway development methods and longwall mining with ploughs or shearers combined with optimised process coordination offered pioneering solutions - solutions to enable costeffective coal extraction in the long term without compromising safety. Countries such as Russia, the Ukraine, China and the Czech Republic, where extraction is now reaching similar depths, can now benefit from this experience: they do not need to go through the same process of trial and development, but can draw on Germany's findings and ultimately save on costs. Now, Germany is offering this knowledge and experience on the international market on a client- and deposit-specific basis to continue providing mining countries with safe and cost-effective coal mining solutions and secure the energy supply. The presentation gives a number of examples of how international mining companies have used expertise from Germany to better meet the challenges of deep mining.

Aug 1, 2013

By B. Benmokrane, G. Ballivy

"RésuméLe mécanisme de transfert des charges et le processus de décohésion le long des scellements d'ancrages scelles dans des massifs rocheux sous des charges de tensionnement peut être examine par instrumentation de l'ancrage à l'aide de jauges de déformation. Dans ce contexte il est présente ici les résultats d'une étude, en vraie grandeur sur chantier, ayant porte, d'une part sur des essais d'arrachement conventionnels et d'autre part sur des essais déflagrée barres d'ancrages instrumentées et scellées à l'aide d'un coulis de ciment dans un massif rocheux sain et compètent. Les résultats décrits ici, particulièrement les profits de contraintes de cisaillement le long de l'ancrage, obtenus à partir des valeurs de déformations relevées sur les jauges, ont permis de préciser le niveau de chargement correspondant à la décohésion initiale du coulis de scellement, d 'examiner l'effet de la décohésion sur la distribution des contraintes et de caractériser le fluage du système barre d'ancrage/coulis de scellement.ABSTRACTThe load transfer mechanism and the debonding process along grouted rock anchor, subjected to tention loads, can be examined through the instrumentation of the anchor with the aid of strain gauges. In this context, the resultsof a full-scale site investigation including classical pull out tests and creep tests are presented in this paper. These tests were performed on instrumented bars which were cement grouted in a competent rock mass. Results presented in this paper concern, among others, shear stress pro/ties along the grouted anchors which were determined from strain values obtained from the strain gauges. These results have been used to: (1) predict the load level corresponding to initial debonding of the grout; (2) study the effect of debonding on shearstress distribution along the anchor; and (3) characterize the creep behavior of the bar anchor/cement grout system."

Jan 1, 1991

By James P. Sloss

MOST students that plan to enter the mining profession attempt to obtain some kind of practical experience before graduation. Six or seven years ago it was an easy matter for undergraduates to find employment during the summer vacation and return to school in the fall filled with enthusiasm to dig deeper into the theoretical field. However, during the past few years it has become extremely difficult for an inexperienced undergraduate to obtain even a menial job in mining. This was the situation which presented itself to the author and his partner, T. M. Patten several months before school closed in May, 1934. At that time, Mr. Patten's training consisted of two years study in Mining, and mine included three years' study in Mining Geology at the Missouri School of Mines and Metallurgy. With this technical training and no practical experience, we conceived the idea that custom assaying in some of the western mining districts should be a lucrative business. We thought that the renewed interest in prospecting for gold and the opening of new mines should provide more assay work, and believed that we might secure it if we were on the spot where the assaying was needed. We realized that it would be out of the question for us to obtain the necessary equipment with which to establish an assay office. Even if such an office were established we had a maximum of but three months during which to operate. So we determined to build some kind of inexpensive equipment that could be placed in an automobile, or trailer, and be moved from one camp to another. We then began to study the theoretical aspects of assaying and started experimental work with the equipment that we proposed to build.

Jan 1, 1935

[CONTENTS COUNTY NO. OF MINES MINE INDEX PAGE]

Jan 1, 1980

When most people think of coal mining, they envision men in soot-covered clothes and hard hats digging at deposits in deep underground caverns. These mental images commonly include coal cars rumbling on rails as they emerge from the earth, filled to the brim with rocky ore. The world of modern, longwall coal mining is a far different place. Yes, it?s underground, the miners still wear hard hats and the environment is filled with soot. However, today?s mining operations are carefully monitored and the entire process is highly automated. Five kilometers (3 miles) underground, a sophisticated, high-powered mining machine moves steadily through a 2-m (6-ft) high tunnel at an average speed of 3.2 km/h (2 mph), carving out coal, then conveying it to a crusher and carrying it to the surface. Instead of digging out the ore, a longwall mining system slices it from the exposed tunnel face, using giant rotating shears. The shorn coal tumbles onto a conveyer below the shears and is conveyed to the stageloader, where it is crushed and dumped onto the main conveyer belt that eventually hauls it out of the mine. Integral to the longwall shear and conveyor is a moving metal roof that protects it from the thousand plus feet of ground above. The ceiling panels automatically advance above the shears, powered by hydraulic roof supports that stand on the other side of the tunnel, moving in a slow, sideways lock-step with the shears. This complex and massive machine makes longwall mining the most ef?cient and productive method for excavating coal. In fact, it produces 2.7 kt to 22.6 kt (3,000 to 25,000 st) of ore per shift, versus 544 to 907 st (600 to 1,000 st) for the conventional room-and-pillar mining. Using that method, miners develop one section of a mine at a time after carving out load-bearing columns of coal to support the roof above their heads. Longwall mining also is considered safer than the room-and-pillar method, largely because the process is mostly automated, requiring fewer workers. Still, longwall mining has its drawbacks: The equipment is expensive and the mining conditions are harsh. An entire longwall system can cost between $50 million and $100 million, while the electrical controls used to operate it can cost an additional $1 million to $2 million. These investments grind away all day, every day, in hot tunnels filled with coal dust.

By Harvey N. Davis

MUCH has been written and said during the last twenty years about the place of the engineer in modern life, about the fundamental role that he plays both in developing and in maintaining the material foundations of modern civilization, about the advantages, and also the dangers, of the machine age that he has inaugurated, about the Frankenstein problems that he has unconcernedly foisted upon a generation utterly unable to cope with them, and about the obligation that rests upon him to stop inventing machines and turn his almost legendary energy and skill to inventing institutions that will constitute a solution of the problems he has raised, and contrariwise about his utter inability to offer wise or useful counsel in fields outside the narrow boundaries of his technical training.

Jan 1, 1938

By I. I. Beloglazov, G. A. Iusupov, A. Ju. Feoktistov

"The aim of this paper is to study the numerical modeling of the crushing process in a jaw crusher with complex motion jaws using Discrete Element Method (DEM). The main goals are to ensure the conformity of numerical simulation results to the experimental data, optimize the operating modes and the crusher design and develop automated verification and calibration methodology. It is offered to use automated selection of mathematical model parameters using large- or laboratory-scale experiments instead of deriving parameters from conventional intensive material tests (e.g. drop-weight test). Experimental data were obtained from a large-scale crusher designed and manufactured by the company “Mekhanobr-Tekhnika”. Both jaws have their drive shafts located asymmetrically; one jaw is driven in the upper part, the second at the base. The crushing process involves fragmentation of single smoothed rectangular granite particles of the same weight. During the experiment, the required parameters such as particle size distribution were obtained for further computer simulations. Based on the obtained experimental data, the Rocky DEM model was built. Simulation breakage parameters were calibrated using automated parameter selection methodology based on multiple set of parameter-controlled simulations. A good correlation of the experimental data and numerical simulation data was obtained. The methodology in combination with well-known capabilities of simulation modeling will help reduce the research time in the development of new mineral processing equipment.INTRODUCTION Preparation of rock mass for enrichment includes the power-consuming processes of crushing and grinding. Initial rock mass crushing is performed by means of drilling and blasting operations. To reduce the average size of a rock piece, primary crushers, mostly jaw crushers, are further applied. The advantages of the jaw crusher are simple design, easy maintenance and repair. One of the drawbacks is large oscillating masses and, thus, high power consumption during operation (55 - 200 kW). Jaw crushing simulation will help optimize the crushing process and improve further rock transportation and processing performance."

Jan 1, 2018

By C. C. Stevenson, Thomas Varley, E. P. Barrett, ROBERT H. BRADFORD

The art of treating ores by the chloride volatilization process is still in the experimental stage. The process has not been sufficiently developed along metallurgical lines to warrant a definite statement as to the exact place it will occupy in the industry. The basic theory of the process has received the attention of prominent metallurgists for 20 years, and considerable research and experimental work have been carried on. Much of the experimental work done has never been published; if the accumulated results were made known, they would greatly aid,. the further development of the process. This bulletin aim~ to bring the salient features of the process to the attention of metallurgists for the purpose of furnishing information to and receiving comments from interested parties with the ultimate hope that the process will be a commercial success. If commercially utilized, the process will fill a long-felt want in metallurgy, especially in the treatment of oxidized and semioxidized or" carbonate" ores of copper, lead, and silver. Such ores are difficult to treat by gravity concentration or by flotation: in the former their tendency to slime upon crushing and their being of lower specific gravity than the sulphide minerals cause serious losses; in the latter much has been done in sulphidizing oxidized ores and subsequently recovering the artificial sulphides by flotation. Difficulties in proper sulphidizing and the low recoveries obtained have not balanced the cost of the treatment in many plants and in very few has it proved successful. Evidently there is a big void to fill in the treatment of these ores. No radical changes in present methods are forecast, but it is obvious that chloride volatilization can have a distinct place as a method of treatment for ores that are not readily amenable to present methods. In many plants it might replace concentration methods, especially where part of the mineral content in the ores exists in forms other than sulphides.

Jan 1, 1923

By A Buckley

Many policy issues facing the mining industry and affected communities are at a level of complexity that they can be called ‘wicked’ problems. The term ‘wicked’ in this context is used, not in the sense of iniquity, but rather as social and economic issues highly resistant to resolution. For the resource extraction sector and affected communities there are an array of challenges embedded in the industry’s production and profit paradigm, the remoteness of mineral reserves and affected communities’ expectations of economic benefit and a positive legacy. The mining industry as a whole is dominated by economic, political, legislative and market structures that influence and constrain interactions between mine operations and local communities. For communities, with particular reference to regional Western Australia, intractable problems include the uncertainty of, yet increasing dependence on, a mining economy. Questionable outcomes for local communities include the limited realisation of local employment and business development benefits, and low overall outcomes or low multiplier effects. ‘Wicked’ problems, according to the literature, are best addressed via collaboration. In the mid-west region of WA, with mining and infrastructure construction underway, alliances have formed between mining companies, the major port and rail infrastructure project (Oakajee Port and Rail) and regional and local governance stakeholders. The major impetus for these affiliations is to expedite planning and associated infrastructure development taking into account the lessons from other mineral-led regions. What has resulted is an array of innovative approaches to stubborn problems including planning well in advance of full-scale mining; regionally coordinated procurement; ‘mine ready’ local businesses; and strategic investments in social infrastructure; including community trust funds paid in advance of project delivery. This paper examines these innovative approaches/alliances and assesses their effectiveness in addressing long standing mining/community dilemmas.

Nov 22, 2011

By Plato Malozemoff

While this conference is dedicated to the examination of "Challenges in Mineral Processing," the broader aspect of the pursuit of this subject is Research and Development in the Mining Industry. When I was asked to speak at this symposium, I hesitated to accept. While my early schooling, training and professional occupation were in the field of this symposium, it was so long ago that I no longer feel competent to contribute anything of interest to you except perhaps for a limited historical perspective, which most of you probably already know. However, it might be worthwhile to explore the more general aspect of research and development from the viewpoint of management, as this is the stance from which I dealt with the subject for the last 30 years or so. While most managements generally have a positive view of research and development, few of the leaders in the mineral industry have actually had the personal experience of doing research for a long enough time to have obtained a full understanding and the feel for its place in the long-term technological innovation that our industry must foster. I graduated from the University of California in Berkeley with a Bachelor of Science degree and a major in metallurgy. It was during the great depression of the thirties, and it was difficult to obtain a practical job in the industry. I got a scholarship at the Montana School of Mines and received a Master of Science degree in ore dressing under Professor A. M. Gaudin, followed by another year with him pursuing research. Anyone who studied under him, or knew him well, would assert that this was a unique experience. Gaudin had a brilliant mind and a profound respect for science and the scientific method. He wished to know the scientific basis for every new technological appli-

Jan 1, 1989

By Wm. W. Odell

A study of certain gas making and fuel problems peculiar to the gas industry of California has been made by the Bureau of Mines. The work was done at the request of, and in cooperation with The California Gas Research Council 2, for the purpose of obtaining basic information on the gas-making fuels available to California, and their applicability to the present and future needs of the gas industry in that State. The data obtained have been applied in outlining a construction program, and indicate the possibilities in efficiently utilizing fuels in making gas by other than the oil-gas process. This paper presents an outline of the study and a summary of the principal results obtained, with some of the more important conclusions and recommendations based on this data. Gas is produced in California by processes which are both unique and different from those common to other parts of the United States. The bulk of the manufactured gas is made in and distributed from two main districts which are centers of population - namely, the Los Angeles district and the San Francisco Bay district. The gas manufactured in the Bay district is, almost exclusively oil-gas, whereas that produced in the southern part of the State, where natural gas is available, is mostly mixed natural gas and reformed-gas, but oil-gas is the chief product when the supply of natural gas is inadequate. Practically all of the gas companies are equipped with oil-gas generating apparatus, and anticipate using it in the future. As the continued use of the oil-gas process to the exclusion of all other processes, depends upon a continued supply of oil at a low cost, and the prospect of obtaining such low-priced oil in the future is somewhat uncertain, the questions have arisen: What will the future gas-making process or processes be? When will it be necessary to make plans for the installation of different gas generating equipment, and what will that equipment comprise?

Jan 1, 1926

By G. M. Potter

During the investigation of the occurrence of manganese deposits in the western United States, examining engineers of the Bureau of Mines collected samples from four properties in Siskiyou and Mendocino Counties northern California. As the ores were too low-grade to be acceptable to manufacturers of ferromanganese, beneficiation studies were made between 1941 and 1945 to determine the amenability of the ores to concentration. The Johnson and Reynolds properties are near Fort Jones Siskiyou County. The ore occurs in a number of small lenses in that area. Samples were taken for testing for amenability to treatment in a small custom-gravity plant, tentatively planned. by the Waiter Johnson interests of San Francisco. A 2-ton representative sample was obtained from numerous exposed portions of an outcrop on the property of the Mayland Mining Co. The Mayland mine is about 8 miles from Sawyers Bar in Siskiyou County. The ore body consists of stringers and irregular masses of oxide, and. silicate ore scattered through quartz, which these minerals have replaced.

Jan 1, 1952

By W. G. McBride

THE present demand for men with engineering training exceeds anything in the history of the profession. Recent estimates indicate that mechanization of war has reached such a stage that at least twelve horsepower is required now for every one horsepower needed to run the machines of the first Great War. The scale of operations exceeds anything in the past, while more territory and people are involved than ever before. Many of our allies have inadequate or no facilities for producing the thousand and one articles absolutely necessary to the conduct of modern warfare. Lack of preparedness has made it necessary to produce at an unparalleled rate to gain parity with the enemy, while our losses have been so heavy that replacement, in itself, presents a task which might well stagger less courageous peoples. This means that not only is there an unprecedented demand for engineers to produce the machines, munitions, and supplies of war, but there is a correspondingly large need for men with engineering skill in the uniformed forces to operate and maintain the vast numbers of ships, 'planes, tanks, trucks, radios, and a myriad of other devices to carry on the varied activities of war. This abnormal demand came upon us after almost ten years of stagnation in the engineering industries. During this time many trained engineers drifted into other callings, while the lack of jobs for graduates caused a falling off in the number of men training for this profession. Consequently, the supply of well trained engineers was below normal when the madman of Germany precipitated us into the present turmoil. Added to all this, we in Canada are still suffering from governmental inefficiency in the utilization of the available supply of engineers. In the armed forces, engineers have been assigned to office and other work where their engineering training is not only wasted but for which men with more suitable training could be found. Mining engineers are debarred from service as aeronautical engineers, and students in mining engineering are denied the bursaries provided for aiding students in engineering. Mining and metallurgical engineers are both barred from the Ordnance department of the army. This arises from a misunderstanding in relation to engineering training. In Canadian engineering schools, all engineers are given a sound training in the branches of human knowledge which are fundamental to engineering: mathematics, physics, and chemistry. The basic difference between the several categories of engineers lies in the fact that training in the application of this fundamental knowledge to the solution of engineering problems is given in different subjects.

Jan 1, 1942

Seventy-three of the 90 naturally occurring elements that are found in the earth's crust are metals or metalloids. The quantities of metals used annually in the United States range from about 100 million metric tons (steel) to a few kilograms (osmium). The recovery of metals from discarded products or industrial process wastes, especially those metals that are used in large quantity, are very expensive, or are unusually toxic, is important to the national economy and to the natural environment. From its inception in 1910, the U.S. Bureau of Mines (USBM) has been the Government's prime source of information on metals recycling, as well as a major innovator in recycling technology. Statistical data on scrap generation and processing have been summarized annually for many years in the USBM's Minerals Yearbook. Most of the data for individual metals discussed in this report were extracted from that publication.

Jan 1, 1993

By D. R. Tesarik

As part of its research program to investigate ways of improving resource recovery and reducing subsidence, researchers from the U.S. Bureau of Mines placed instruments in the B-North ore body of the Cannon Mine, Wenatchee, WA, to monitor cemented backfill and rock deformation during mining. The vibrating-wire gauges proved to be reliable and versatile, and approximately half of the instruments are providing data after 2 years of use. A two-dimensional, finite-element model was used to analyze the Cannon Mine's multilevel bench cut-and-fill mining method and predict rock and backfill displacements. The model accurately predicted rock displacements, but the predicted and measured displacements in cemented backfill had a correlation coefficient near zero, indicating that the model should only be used to predict rock displacements and not backfill displacements. A finite-difference model was also used to evaluate the stability of a cemented backfill pillar. Results can be used to conservatively predict backfill stresses, but on-site observation of pillar failures coupled with in situ measurements are needed to make more accurate predictions. An ongoing evaluation of the mining system has indicated that filling the primary stopes tight to the back with cemented backfill allowed these pillars to carry overburden loads soon after the cemented backfill was placed.

Jan 1, 2010