Search Documents

By F. Ysla, M. Mendoza

This proposal, based on the CIEMAN Cajamarca - Hualgayoc initiative, focuses on “Transforming Abandoned Mine Lands’’ We aim to study and assess the feasibility of an innovative rehabilitation method. Contaminated soils will be moved from the upper to the lower site, encapsulated with geosynthetic barriers, and covered with topsoil. The decontaminated upper area will be used for planting trees and large-stemmed plants for hiking and tourism, while the lower encapsulated area will support livestock and short- stemmed crops. This study will evaluate the economic viability and multi-use potential of this technique, promoting sustainable land recovery in Cajamarca, Peru.

Feb 1, 2025

By S. J. Gerdemann

In support of its objective to improve mine safety, the Bureau of Mines has searched for better materials and systems to anchor roof bolts. TIlis report describes a study on the effects of mine waters upon accelerated gypsum, one of the materials under consideration. The accelerated gypsuw dissolved at an appreciable rate relative to an assumed 10-yr life span of a roof bolt. Surface orientation, initial ion concentration of a dissolving solution, and flow rate of the solu-tion had substantial effects on the dissolution rate. Factors such as water-cement ratio, accelerator content, wax capsule additions to the gypsum in cartridge-installed bolts, surface area, temperature, and curing duration had little effect. In an actual roof-bolt environment, dissolution will occur in static solutions to the solubility limit of gypsum (~2 giL) and cease, result-ing in minimal damage; but in flows of unsaturated solution as slow as 1 L per month, a loss of up to 10 pct will occur in 2 yr. Since miners cannot readily measure the flow or ion concentration of static-appearing water at every roof-bolt site, all such water must be assumed to be pure and flowing. It is recommended that gypsum-bonded roof bolts be confined to dry roofs only.

Jan 1, 1983

By Y. H. Zhan

A new P(MAAA) latex was developed and used in separation of ultrafine apatite from calcite and silica by means of selective flocculation. The latex was found to flocculate selectively apatite from apatite/calcite and apatite/silica mixtures in the presence of sodium tripolyphosphate and sodium silicate over a pH range from 9.1 to 9.4. The separation of apatite from calcite was more selective with sodium tripolyphosphate, while the results of the separation of apatite from silica were better when sodium silicate was used. In the apatite/calcite system, 90% apatite recoveries into a concentrate containing 34% P2O5 were possible in the presence of 4 mg/l of sodium tripolyphosphate at a latex dosage of 2.2 kg/t. In the apatite/silica system, 80% of apatite could be recovered into a concentrate containing 33% P2O5 in the presence of 20 mg/l of sodium silicate at a latex dosage of 1.1 kg/t. Deposition tests were used to study the interaction between the latex and the mineral surfaces. The results revealed that deposition density of the latex on apatite was higher than on calcite; the differences between the deposition onto these two minerals were higher at pH 9.2 than at 7.2. The results point to the stronger interaction between the latex and apatite surface when compared with the latex-calcite interactions.

Jan 1, 1998

By T. R. A. Davey

Previous publications on the application of EIETSIM include the modelling of an electrolytic zinc plant and a copper flash smelter. In the present case METSIM has been used to model the desilverising of lead by the reagent zinc, whereby a silver-zinc intermetallic compound is formed, and floats out of the lead. This compound has a variable composition, depending upon the ratio of dissolved zinc/silver in the lead bath. Its solubility in lead decreases with falling temperature. A number of variations and modifications of the Davey Desilverising Procedure are modelled, and applied to a wide range of silver contents in lead bullions at several plants. METSIM uses both feed- back and feed-forward controls to simulate plant conditions, and a logic control to distinguish between different phases in the Zn-Ag system. Use is made of extensive (previously unpublished) fundamental data on the ternary Pb-Ag-Zn system, and of plant data, to establish certain operating parameters.

Jan 1, 1993

By E. Demir

Transportation cost is the dominant cost and accounts for almost half of the total mining cost in surface mining. Therefore, determining transportation cost is critically important for the economic feasibility of mining projects. Turkey produces around 85 million tons of lignite per annum. The biggest state-owned company, Turkish Coal Enterprises (TKI), accounts for 43 per cent of the country?s total lignite production. Around 85 per cent of the produced lignite is used in power plants for electricity generation and 15 per cent is used for domestic heating in cities and urban areas. On behalf of the Turkish government, TKI distributes around 2 Mt of lignite annually, at no cost to poor needy families countrywide in accordance with Social Assistance and Solidarity Funding aid. Subcontractors are utilized for lignite transportation, and conflicts arise due to the different transportation cost calculations at different mines. A robust model that provides unbiased cost estimations is therefore of paramount importance. This paper presents the transportation cost estimation software, NAKMAL, that has been developed for estimating the transportation cost of lignite from the mine face, including excavation and loading, to various final destination points through five different transportation scenarios. NAKMAL was designed using VisualStudio.NET, validated using field data and some case studies, and it is currently being used by TKI for calculation of transportation cost country-wide.

Jan 1, 2012

By Harry Littleton, Jr. Scarber, Wanliang Sun

"The Lost Foam Casting (LFC) process is relatively immature when compared to other casting processes. To make the process more robust, computer modeling is needed to reduce lead times and casting defects. In this study, metal filling of lost foam aluminum castings was visualized using state-of-art real time X-Ray technology. Metal filling of the lost foam casting was simulated using a commercial software package. The result of the computer simulation was compared with the results of the real time X-Ray visualization. Some of the computer simulation results agreed with the real time X-Ray visualization, but some did not. Based on other studies using real time X-Ray technology, new input variables, such as foam density variations, were developed for the computer modeling. With the new variables, modeling of the lost foam casting process becomes more realistic. IntroductionMold filling of the Lost Foam Casting (LFC) process is an important step toward making a quality part. In the LFC process, molten metal is poured against a refractory coated foam pattern surrounded by dry sand. At the pouring temperature of aluminum, the foam pattern is decomposed into 30% (wt) gaseous and 70% (wt) liquid foam pyrolysis products. Existence of the gaseous foam decomposition products significantly increases the back pressure on the metal stream compared with the conventional open cavity sand mold. Entrapment of the liquid pyrolysis products during the metal filling generates many casting defects, such as internal pores, fold and blisters. Existence of these casting defects sometimes seriously degrades the quality of the components manufactured by the LFC process. Understanding and controlling the metal filling of the LFC process will certainly make this process more robust."

Jan 1, 2004

By F. L. Pirkle

A heavy mineral deposit about 1.6 km (1 mile) in length, 0.13 km (0.08 mile) in width and averaging about 3 m (10 ft) in thickness is exposed approximately 130 km (80 miles) east of Denver, along Interstate 70, in Elbert county, CO near the town of Limon. The deposit is exposed in a geomorphic feature known locally as Titanium ridge. The dominant heavy minerals, accounting for about 70% of the total heavy-mineral suite by weight, are ilmenite, garnet and zircon. The mineralized zone appears in a series of visually interpretable facies that are stacked vertically and represent subtidal, forebeach, backbeach, washover fan and aeolian depositional environments. These paleoenvironments are analogous to depositional environments represented by a modern heavy-mineral bearing facies tract on St. Catherines Island, Ga. Thus, Titanium ridge provides evidence that heavy-mineral accumulation models for late cenozoic deposits in the Georgia and Florida coastal plains are applicable to heavy-mineral deposits of the Western Interior subsurface and, by implication, the Western Interior Seaway, extending from Mexico to the Canadian Arctic.

Jan 1, 2012

By Robert A. Cortese, Henry E. Perlee

Coal dust and float coal dust, produced during normal mining operations, in underground coal mines, are carried from the point of origin downstream by the ventilating air, where it deposits on the surfaces of the mine entry. In an explosion, this dust is lifted from the surfaces by the aerodynamic disturbances and, if of sufficient quantity, can continue to propagate the explosion. To prevent the surface coal dust from contributing, it must be inerted, typically by spreading pulverized limestone, i.e., rock dust, over the coal dust surface. To facilitate the dusting operation, the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory(PRL), developed an automated system that continuously monitors the accumulation of coal dust. This system could activate a rock-dusting machine that disperses rock dust into the ventilation air when dangerous deposits accumulate and deactivate the machine when sufficient inert has been deposited on top of the coal dust. The system consists of a microprocessor-controlled optical float dust deposition meter. This device measures the light intensity reflected from a deposited layer of dust. A standard cap lamp is used as a fixed-position light source. From the reflected light signal, the microprocessor determines the hazard level of the deposited layer and performs the appropriate action. Full-scale studies conducted in the Experimental Mine at PRL's Lake Lynn Laboratory, using alternating thin layers of rock dust and coal dust, successfully demonstrated the operation of the device. Based on the statistical data from these studies, a mathematical model was developed to predict long-term error in total rock dust content using this inerting procedure. Downwind dust dispersion was also examined to provide optimum placement of the dust sensors and to determine the need for better rock dust dispersion techniques.

Jan 5, 1998

By R. S. Archer

SILICON is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13. per cent, of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 258, Special 178 and 51S of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both "normal" and "modified" sand castings.

Jan 1, 1927

"Some of the tools developed for the processing of nickel laterite ore by resin-in-pulp (RIP) may be applicable to the remediation of metalliferous mine drainage (MMD). In both cases, recovery of metal value and production of a stable waste stream appropriate for long term storage is desired. MMD typically has the additional challenge of management of toxic low-value metals. Seen in this light, innovations in RIP reactor configuration, selective elution strategies and novel synthetic ion exchange resins become useful tools for taking on the MMD challenge in a way that maximizes both environmental and economic benefit. INTRODUCTIONAcid mine drainage (AMD) is a common problem in any country with significant past mining activity. When sulphide containing minerals, tailings or slag are exposed to water, oxygen and sulphur oxidizing bacteria, AMD will result. Abundant and reactive iron sulphide minerals leach first, providing acidity and the ferrous/ferric couple that can enhance the oxidation kinetics of other minerals. If this runoff contacts encounters acid consuming carbonates or silicates, the acidity may be neutralized, but certain heavy metals remain in solution and can continue to be an environmental hazard (Gray, 1997). For this reason, the remainder of this paper will refer to the broader term metalliferous mine drainage (MMD) rather than acid mine drainage. In either case, such drainage, containing high heavy metal concentrations and often significant acidity, is toxic to aquatic life and can lead to significant damage to ecosystems and to public watercourses. MMD is a problem most commonly associated with now defunct sulphide mineral mines, but similarly toxic streams can result from many types of waste, such as poorly stabilized leach tailings, slag heaps, and coal flotation tailings (Johnson and Hallberg, 2005; Lee et al., 2002; Sainz et al., 2002; Schüring et al., 1997). In any case, the management and remediation of MMD is an important ongoing problem for the resource industry, particularly for the many mines in Canada closed before the advent of more stringent environmental standards. MMD remediation represents a significant long term expense for the resource industry. Multi-disciplinary efforts to understand and mitigate this problem range from creation of artificial wetlands (Poulin and Lawrence, 1996; Sheoran and Sheoran, 2006) to sophisticated biochemical reactors and precipitation processes (Hatami, 2010). Certain remediation technologies such as ion exchange offer methods to make a saleable product by recovering valuable dissolved metals. This paper will show how these technologies can help defray the cost of remediation, and offer potential to turn a dangerous waste stream into a useful product."

Jan 1, 2012

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan

During the last phase of the Circunvalacion Norte project in San Jose, Costa Rica, preliminary designs for an underpass structure of over 16 km (10 miles) considered drilled shafts as an earth retaining system. Since the project’s execution was delayed and close to the deadline, it was necessary to optimize this structure, with the drilled shafts being the most critical aspect. The key element in order to obtain an improved design was characterizing the job site with a specific site study for seismic demand, and the use of advanced numerical modelling, considering soil-structure interaction. The site investigation comprised the CPT, PMT, MASW geophysical tests, deep exploration drilling, and triaxial compression tests. The terrain was modeled using an advanced constitutive model with hardening plasticity calibrated from the triaxial tests. Plaxis software was used to calibrate the seismic model for the terrain and for the dynamic analysis. Two conditions were considered for the retaining structure: free-head and fixed head. A parametric study with drilled shafts of 1.0 m (3.3 ft) and 1.2 m (3.9 ft) in diameter, and center-to-center spacing of 1.3 m (4.3 ft) and 3.0 m (9.8 ft) was conducted in order to obtain an optimized structure. For each condition of the drilled shaft wall, the computed deformations were compared for two spectrum designs: site-specific spectrum and seismic code generic spectrum. Finally, a dynamic analysis was performed to check the performance of the drilled shafts with optimized spacing using a control earthquake. Based upon seismic performance curves, the analysis showed the possibility of greater spacing for the drilled shafts compared to the original design, obtaining a 32% reduction in the total length of the drilled shafts in the project.

Oct 1, 2022

By J. Lapointe, S. Leger, D. Proulx

"Une méthode non-électrolytique est utilisée pour plaquer au cuivre la fibre d'amiante chrysotite. En variant les paramètres de placage du bain, on détermine les conditions optimales du taux de deposition du cuivre . Une analyse par diffraction aux rayons-X permet une comp araison relative des résultats de placage et de précipitation d'oxyde cuivreux dans Ie bain. Le traitement de placage a pour but d'assurer une adhésion suffisante de la fibre dans une matrice métallique Iors de la fabrication éventuelle de materiaux composites.IntroductionCette communication se veut un compte-rendu de nos travaux sur Ie placage au cuivre de la fibre d'amiante chrysotile, en vue de I'incorporer éventuellernent dans une matrice métallique. La fibre d'amiante est constituée de fib rilles élementaires d'un diamètre d'environ 0.02 um qui ont une résistance en tension de I'ordre de celie de la fibre de verre ou de carbone(1). Pour être efficace, la fibre de renf'ort d'un matériau composite doit d'une part, avo ir des propriétés mécaniques intrinsèques élevées, et d'autre part, adhérer solidement â la matrice pour que Ie transfert de charge s'effectue sans qu'il y ait décohésion entre les composantes du matériau.La fibre d'amiante étant naturellement soyeuse, il faut la traiter superficiellement pour que l'adhésion avec la matrice soit suffisante. Ainsi, on recouvre la fibre de phénol-formaldéhyde(2) ou de silane(3) lorsqu'elle est employée avec une matrice polymere. Dans Ie cas d'une matrice métallique, ces dépôts organiques ne peuvent resister aux températures de mise en oeuvre, d'où l'intérêt de plaquer les fibres par un dépôt métallique.Dans cette étude, nous rapportons les résultats relatifs à la methode utilisée pour plaquer au cuivre la fibre d'amiante chrysotile. Une analyse par diffraction aux rayons-X permet de comparer les différentes conditions de placage non-électrolytique."

Jan 1, 1985

By E. Godin, M. Rigaud, S. C. Panigrahy, I. Malinsky

"RésuméDes boulettes de concentres d'hématite spéculaire à basse silice ont été produites en substituant la bentonite par de la tourbe, adéquatement traitée, additionnée d'une faible quantile de soude caustique durant le boulettage. La réductibilité de telles boulettes et leur gonflement pendant la réduction ont été évacues, en utilisant quatre mélanges gazeux différents, formes de H2 - CO - N2.L'influence du pouvoir réducteur du gaz utilise, sur le gonflement des boulettes, à été mis en évidence. Quelles que soient ces conditions réductrices, les propriétés mesurées sur les boulettes liées a la tourbe sont comparables aux propriétés obtenues avec des boulettes traditionnelles liées à la bentonite.ABSTRACTAdditions of peat moss and small quantities of NaOH during balling of low silica specular hematite concentrates have eliminated the need to use bentonite as a binder. The reducibility and swelling of such pellets have been evaluated using four different gas mixtures, consisting of H2 - CO -N2. The influence of the reducing power of the gases, on the swelling behaviour of pellets has been documented. Under the different reducing conditions, this new type of pellets exhibit properties similar to the ones obtained using bentonite."

Jan 1, 1987

By Q. Zhang

The necessary capability of the gravity transportation pipeline system for cemented coal gangue backfilling at the Suncun Coal Mine, China, is about 74.4 m3?h-1 according to mining production and working times in the mine. It is estimated that the working velocity and maximum pipe length-backfill depth ratio of the backfill system are 3.82m?s-1 and 5.4, respectively and that the probable backfill capability of the system is 110.18m3?h-1. Results of hydraulic calculations for the backfill transportation system show that the designed backfill system is reliable in flowability and sufficient for backfill capability needs.

May 1, 2007

By Patrick J. Hannigan, Alex Ryberg, Rozbeh B. Moghaddam

Driven piles are widely used for foundation support. In the vast majority of cases, an increase in pile capacity occurs with time which is referred to as “set-up.” However, in a very limited number of cases, a decrease in capacity with time can occur. This phenomenon is referred to as “relaxation.” This paper will provide a brief review of the relaxation phenomenon, as well as pile driving information and dynamic test data on cases where relaxation has occurred. The pile types in the presented relaxation cases include H-piles, open-end and closed-end pipe piles, prestressed concrete piles, and prestressed concrete piles with H-pile stingers. The soil conditions where relaxation occurred includes dense to very dense fine sands, heavily over consolidated clays, and weak laminated rocks. Relaxation information from 36 piles at 26 sites is assessed. The collected data will assist foundation designers by identifying the subsurface conditions where relaxation has occurred, as well as by documenting the corresponding relaxation magnitude. One method of addressing relaxation when it is encountered is to drive the foundation piles to a greater end of initial driving capacity than required long-term. Hence, the identification and quantification of the relaxation magnitude will be beneficial to foundation designers installing similar pile types in similar subsurface conditions. The paper will also present pertinent observations and recommendations on mitigating relaxation when encountered. INTRODUCTION One of the earliest observations of a decrease in redriving resistance following initial driving was reported by Miller (1937). He reported that piles driven into a saturated, coarse grained soil could lose 40 to 50% of their resistance when redriven 24 hours after initial driving. Yang (1956) similarly reported that after a break in driving, a decrease in driving resistance could be encountered for piles driven in dense fine sand, inorganic silt, or stiff fissured clay. Parsons (1966) in his paper that described piling difficulties in the New York City metropolitan area termed this phenomenon “relaxation”. In this time period, pile capacity was most often evaluated from a pile driving formula frequently checked by a static load test. Hence, the true magnitude of the capacity decrease on a given pile was often poorly quantified. Furthermore, dynamic measurements that could determine what influence driving system performance variation had on the observed redriving resistance were not yet readily available.

Jan 1, 2019

By Donald O. Capstick

In 1481, U.S. Bureau of Mines personnel conducted a survey of mines, prospects, and mineral resources in the Table Mountain RARE II area. There are no mines or active prospects in the study area. One prospect in the study area, the Waterfall Prospect, is estimated to contain 480 tons (440 t) of indicated subeconomic tungsten resources averaging about 0.18 percent tungsten trioxide (W03). Other tungsten occurrences are at the Stevens Prospect, just northwest of the area. Stone and sand and gravel deposits in the area are not considered to be resources because equal or better quality material is available closer to major markets. INTRODUCTION The 4,400-acre Table Mountain study area is 13 mi (21 km) southwest of Bishop, California, on the eastern flank of the Sierra Nevada range. The John Muir wilderness adjoins the study area on the southwest (fig. 1).

Jan 1, 1982

"The following articles were produced through funding under Generic Mineral Technology Center for Respirable Dust research. Full articles appear in the proceedings, 3rd Symposium in the Mineral Industries, published in 1991 by the Society for Mining, Metallurgy and Exploration, Inc.Personal Diesel Exhaust Aerosol SamplerV.A. Marple, K.L. Rubow, and Y. TaoParticle Technology, Mechanical Engineering Department, University of Minnesota, Minneapolis, Minnesota(Section ill. Diesel I: Diesel Particulate Measurement, pp. 73-81)Abstract. Techniques are being developed for measuring the mass concentration of respirable diesel exhaust particles found in underground coal mines. Studies have been conducted over the past five years to investigate size selective 18Dlpling techniques to measure the respirable mass concentrations of diesel exhaust and mine dust aerosol particles in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler.Three personal diesel exhaust aerosol samplers have subsequently been designed and evaluated in both laboratory and field settings. These samplers use size selective classifiers for the determination of respirable mass concentrations of mineral dust and diesel exhaust particles. Their designs are based on the premise that diesel exhaust particles are predominantly less than 0.8 µm while mineral dust is greater than 0.8 µm.One design, selected for field evaluation, consists of a 10 mm nylon respirable dust cyclone followed by a 0.8 µm cutpoint impactor and afterfilter. The cyclone removes the nonrespirable particles while the inertial impactor state, collects the mineral dust on an impaction plate and allows the diesel particles to penetrate to an afterfilter. The two sample fractions of the respirable particles ( <0.8 µ.m and >0.8 µm) are gravimetrically analyzed to determine the concentrations of the diesel and mineral dust portions in the respirable coal mine aerosol."

Mar 1, 1992

By J. L. Watson

n the U.S., lead has been produced via blast furnace processing for over a century, and the slags from that pyro-metallurgical process have been accumulating on industrial sites over that extended period. Lead blast furnace slags typically contain both lead and zinc compounds in an iron-silicate matrix, and it appears highly likely that such materials will have to be processed in the near future to meet with EPA regulations. Thus it is appropriate to investigate possible processing routes to render the slags non-hazardous and simultaneously to recover metal values to partially off-set the inherent high cost of processing such materials. There are two major processing alternatives: one being pyrometallurgical and the other hydrometallurgical. The research reported here investigates leaching/solution purification/recovery processes for lead and presents experimental data for the treatment of lead blast furnace slags from S.E. Missouri. The results of the research suggest that both lead and zinc can be removed effectively from the slag, and that metallic lead can be recovered directly from the organic extractant utilized for solution purification.

Jan 1, 1995

By Ramanathan C, Prasad P. V. S. R

The most critical challenge for any large size storage structures to be constructed on soft compressible soils is bearing capacity and consolidation settlements. Consolidation is the time dependent phenomena, as expulsion of water from soil voids on application of external load will take longer period. It is mainly influenced by soil consistency, permeability, thickness of compressible stratum and presence of free draining layers. This study deals with the foundation solution of a large size Mounded Storage Vessel (MSV) to be constructed on thick compressible stratum whose loading intensity is around 155 kPa and the estimated settlements are greater than 400 mm. Hence, the foundation solution using vibro stone columns is adopted as an effective technique to address the challenges of excess settlements and inadequate bearing capacity. Further to keep settlements within the permissible limit of 50 mm, preloading technique with 60% of actual loading intensity will be utilized. The consolidation analysis of stone column reinforced foundations is carried based on the method given by Han and Ye (2001). The quality of the stone columns is ensured by real time quality control measures and the performance of the stone columns shall be ensured by vertical load tests. Ground settlements was closely monitored with proper instrumentations and the actual degree of consolidation has been verified by Asaoka’s (1978) method.

Sep 1, 2022

By T. Bhambhani

Research at Cytec over the past two decades has shown that the traditional approach for ore metallurgical characterization (typically conducted via laboratory-scale batch flotation tests), which involves changing reagents and conditions one-factor-at-a-time, leads to several pitfalls. The chemical solution thus selected has a narrow un-optimized window of performance and will likely fail in the plant. A holistic approach, called the Flotation Matrix 100? process for ore metallurgical characterization, was developed at Cytec about a decade ago and has been successfully used to develop robust reagent solutions for several operations around the world. The premise for the approach is that flotation outcome from ores is variable and is determined by complex interactions between various physical, chemical and operational factors. A key component of the process is the use of efficient multivariate designs focused on the chemistry aspects (reagents and pulp chemistry), which helps identify the best processing conditions for each ore type, as well as the conditions resulting in poor performance. It also includes advanced statistical methods for dealing with the complexity and variability of experimental data. The holistic approach is illustrated in this paper with a case study on Pb/Zn ores. Using just 18 carefully designed batch tests, it is possible to partially simulate the behavior of each ore type in the plant. The best conditions for each ore type, along with the conditions to avoid, are identified. Along with this, insights are obtained into the reasons for high reagent dosages for certain ore types, and interactions between variables. Keywords: flotation, holistic approach, metallurgical characterization, multivariate experimental designs, base and precious metals recovery, sulfide collectors and modifiers, Pb/Zn sequential flotation

Sep 1, 2012