Search Documents

Spirals have become one of the most popular methods for treating fine coal. Unfortunately, spirals tend to produce an undesirably high specific gravity cut-point and often misplace significant amounts of coal and/or rock. In the present study, a process-engineering tool known as linear circuit analysis was used to identify problems with traditional spiral circuits and to suggest alternative configurations. These analyses indicate that a modified rougher-cleaner circuit incorporating a middlings recycle stream offers the best option for improving performance while maintaining a reasonable circulating load. In light of this finding, a full-scale test circuit was installed and evaluated at an existing preparation plant. Data obtained from the plant tests indicate that the new spiral circuit can simultaneously reduce cut-point and improve separation efficiency. Preliminary economic analyses show that the new circuit provides an attractive payback on the capital investment.

Jan 1, 1998

By R. W. Ruddle

The present state of knowledge on this subject may briefly be summarized as follows: (1) The copper content of the slag increases with the grade of the matte in contact with it; on the other hand, the proportion of copper lost decreases as the matte grade increases, because as a general rule a smaller volume of slag is produced when a high-grade matte is made. (2) The presence of CaO and MgO in the slag decreases the copper content of the slag, and the presence of ZnO increases it; the presence of A1203 seems to have little effect. The influence of the silicate degree is not yet clarified, but on theoretical grounds it seems likely that the copper content increases with the silicate degree of the slag. (3) High slag viscosity, high magnetite contents and low density difference between matte and slag all tend to increase the copper loss. The volume of slag is also an important factor. (4) The effect of bath temperature on the copper loss is not clear and further investigation of this point is needed. (5) It appears possible to recover a large part of the copper in the slag by adding FeS, CaS and other sulphides

Jan 1, 1953

By Regina Rocha, Miguel Humpire

One of the challenges within unitary mining operations is blasting, which has a significant downstream impact on the following processes, which is why mining companies ensure the results of the blasting process through joint work with explosives specialists’ companies.

Feb 6, 2023

By S. K. Ghosh

This paper discusses how the information on ash composition, ash-fusion temperatures, and ash-slag viscosity can be utilized to predict slagging and fouling potentials of a particular coal. A review of several empirical parameters which are commonly in use for determining such potentials is given. Also, some guideline values for interpreting the relative propensity of slagging and fouling of various types of coal are provided.

Jan 1, 1983

By T. W. Guy

IN approaching the problems of sampling coal, a brief statement of certain facts that are more or less taken for granted may be helpful: 1. The coal-mine operator needs reliable data as to the physical and chemical characteristics of his coal in order to plan and control intelligently its mining, preparation, and marketing. The consumer needs such data in order to select the equipment and the coal best suited to meet his requirements, to check the quality of fuel delivered, and the efficiency of its use. Various government control agencies require such data as a basis for classifications and establishment of limits, for use in carrying out the requirements of federal, state or municipal laws. 91. All such data must be obtained by analyses, measurements, or tests made on samples, which are taken to represent the coal tested. It is now becoming generally recognized that, in accordance with statistical laws, test results from samples are not expected to represent the exact qualities of the lot or lots from which they are taken, except within statistical, or "expected limits. Such limits are definitely specified by some present standards of the American Society for Testing Materials and the British Standards Institution. 3. Samples that give ash within satisfactory limits are usually assumed to be sufficiently accurate for other analyses, except under special condi¬tions such as meeting close specifications for coals showing wide variability in sulphur, fusibility of ash, or other quality. 4. In modern coal sampling the increment is recognized as the basis for taking samples. For a given accuracy the number and weight of increments specified are increased with: (a) the expected ash, and (b) the top size designation of the lot to be sampled. 5. It is extremely important that every sampler recognize that: the specified number and weight of increments are minimums, and that the precautions to be used in order to take them properly are also minimums; that in the reduction of the gross sample the sizes specified for the coal after each stage of the crushing are maximum; that the quantities specified to be taken after each crushing stage are minimum; that any short cuts or failures to meet the requirements specified will reduce the statistical accuracy of the results, although it is possible that one or two checks on a few results may seem to show otherwise.

Jan 1, 1943

By Elaine Carballo Siqueira Corrêa

A busca por redução de peso e maior segurança dos veículos vem impulsionando a obtenção de novos aços de elevado desempenho. Os aços bifásicos vêm sendo desenvolvidos e utilizados devido a sua considerável resistência mecânica e boa conformabilidade. No presente trabalho foram realizados os recozimentos intercríticos direto e contínuo em um aço de composição 0,121%C-0,499%Si-1,58%Mn-0,021%Cr com o objetivo de avaliar os efeitos do tempo e temperatura de intercrítica na dureza da ferrita e do constituinte MA (martensita e austenita retida). A avaliação dos resultados foi realizada por meio de microscopia óptica, microscopia eletrônica de varredura e ensaios de ultramicrodureza. Foi observada a influência do tempo e da temperatura na morfologia e na quantidade de constituintes formados. Também foram verificados diferentes valores de dureza nos constituintes e ainda em distintas regiões dos grãos de ferrita. Os resultados indicaram maiores durezas para regiões próximas da interface ferrita/martensita e diminuição de dureza do constituinte MA e aumento dos valores na ferrita com a elevação do tempo.

Oct 30, 2017

In its largest product launch in company history, Cummins Engines welcomed more than 200 customers, vendors and media to witness the unveiling of its new QSK95 engine at its Seymour Engine Plant in Seymour, IN on Nov. 1. It took the efforts of 150 engineers to design the QSK95 and more than $100 million in investments to establish a new production line and test facility at Cummins? Seymour Engine plant. The result of these efforts is a new platform of engines that Cummins says will provide as much as 2,983 kW (4,000 hp) and will be the most powerful, high-speed diesel engine ever built.

Jan 1, 2012

By R. Freer

Recent developments in expanded PTFE membrane filter cloths offer high flow rates and sub-micron particle removal. These high strength, industrial grade filter cloths can be tailored for tubular filters, leaf filters and rotary vacuum drums. Filtration techniques using tubular filters make possible filtration of difficult slurries with the elimination/reduction of filter aids and chemical additives. This paper describes principles of surface filtration, applying the membrane filter cloth and comparisons to gravity separators. Benefits to the mining industry include clear effluent, enhanced solids recovery and accelerated cost payback.

Jan 1, 1996

By Peter Fischer

A demonstration plant for QSL technology with a continuous through-put of up to 10 t/h concentrate has been in operation at the Berzelius smelter, Duisburg, Germany since early 1981. In the QSL-process, both oxidation and reduction steps are performed in a single horizontal long cylindrical reactor. In the present demo-reacior, 2.5 M diameter by 22 M long, these steps are separated by a low partition wall with an underflow opening, to prevent backmixing of slag. -Tests on a variety of concentrates, including high-lead Missouri-type material and lower grades, have shown recoveries and consumables indicating very attractive economics. Investment cost estimates further enhance the economic attractiveness. Environmental protection afforded by the QSL system is a major advantage. The process has proven its reliability and versatility and is now ready for commercialization. Continued test work, including smelting secondary lead materials, is planned.

Jan 1, 1983

By G. Armand, G. Arnold, A. Giraud, C. Auvray

The knowledge and understanding of the mechanical behavior of claystone is of critical importance in the aim of nuclear wastes storage. In this study, specimens of Callovo-Oxfordian claystone (COx) have been obtained from the ANDRA underground research laboratory in Meuse/Haute-Marne (France). This claystone is composed of carbonate inclusions (10-50µm) embedded in an argillaceous matrix (representing expanding clay minerals, such as smectites). The matrix itself is also multiphase and composed of clay aggregates of 1µm-size carbonate and quartz inclusions. This multiphase microstructure leads to a high heterogeneity witch was analysed through nanoindentation test grids. Moreover, the mechanical behavior of the claystone matrix is highly sensitive to humidity and temperature. The nanoindentation tests were performed in a climatic (i.e. temperature and humidity controlled) chamber at relative humidity levels from 50% to 98% and at two temperatures: 20°C and 60°C. In a first step, the curves of indentation were analysed using the commonly used Oliver and Pharr’s approach. Other wellknown parameters as the creep factor were also extracted. In a second step, Fisher-Cripps model (Fischer- Cripps, 2004) and Vandamme and Ulm model (Vandamme & Ulm, 2006) were used to identify viscoelastic properties. A statistical analysis is used in order to extract mechanical characteristics of the different phases. Hardness and elastic modulus decrease drastically with saturation (above 80% humidity) and to a lesser extend with temperature.

Jan 1, 2015

By Frank A. Peters

With the current renewed interest in advancing the technology for producing alumina from domestic raw materials, revisions of previous cost estimates to provide planning data are urgently needed. Completely new cost estimates on a 1973 basis are included for four alumina-from-clay processes and one alumina-from-anorthosite process. These estimates are based on new or previously calculated material balances, recalculated heat requirements, and new equipment designs. The use of larger and more modern equipment has permitted a significant reduction in labor requirements as well as equipment costs. Chemical prices, labor rates, and utility rates typical of late 1973 are used in these cost estimates. In addition to the revised cost estimates, all 21 previously published alumina evaluations compiled by the Bureau of Mines were updated to show the effect of inflation using an inflation index and late 1973 chemical prices, labor rates, and utility rates.

Jan 1, 1974

By Wm. Reisz, Raphael Trousselle

We are now well into our second decade of commercially available electronic initiation systems. Over this time, the technological advances have made electronic systems a very practical option for a wide variety of blasting applications.

Jan 1, 2011

By Richard E. Sylwester

Evaluating surface and subsurface conditions for marine foundations (bridges, causeways, terminals, etc.) is often done with a limited amount of data. Subsurface information for these projects is primarily acquired using traditional methods, such as boreholes, test pits or divers, which tend to be expensive and limited in the area of coverage. A number of geophysical methods, including precision bathymetry, sidescan sonar, and seismic reflection or subbottom profiling are extremely cost-effective and obtain significantly more data than can be acquired using traditional intrusive methods. These geophysical methods provide detailed surface images and continuous profiles of the subsurface stratigraphy. This information can be invaluable for selecting the best location for geotechnical boreholes and to map potential geohazards such as submarine slides and filled or open scour holes. Offshore investigations conducted for a proposed highway bridge (Knik Arm Bridge, Cook Inlet, AK), the retrofit of two existing bridge (Antioch and Dumbarton Bridges, CA) and a proposed cruise ship terminal (Ketchikan, AK) used a combination of geophysical methods to map water depth, detect and map debris on the seabed, map the thickness of unconsolidated sediment, determine the depth to bedrock and identify potential geohazards such as scour holes. The results of the geophysical investigations will be used to select locations for obtaining geotechnical borings, to extrapolate geologic information between existing or proposed boreholes, evaluate the potential depth of scour and design a pile support pier. Geotechnical engineers, offshore contractors and bridge designers are realizing the importance of the early use of offshore geophysics for (i) site characterization, (ii) to reduce the uncertainty of geotechnical conditions thus avoiding designs that may be overly conservative and thus more expensive and (iii) to assist in selecting locations for geotechnical borings.

May 11, 2007

By Allen Chung, John Twomey, Christopher J. Greet

"It is widely accepted that the type of grinding media has an impact on the grinding chemistry and subsequent flotation behaviour of the sulphide minerals being separated. There are countless laboratory investigations demonstrating that inert grinding media produces more oxidising pulp potentials, reduced levels of grinding media corrosion products and superior concentrate grades and valuable metal recoveries. However, taking these results to industrial scale has proven difficult.Work conducted at the Ernest Henry Mine, in north western Queensland, Australia, at laboratory and pilot plant scale clearly indicated that using a high chrome grinding media resulted in significant improvements in both copper and gold recoveries. However, advancing this work to plant trial represented considerable financial and technical risk to the mine.This paper provides details of the protocol developed and used during the high chrome grinding media plant trial. It describes the test regime employed to measure changes in pulp chemistry, and the statistical methodology utilised to interpret the results. The work also highlighted the need for close cooperation between the metallurgists on site and the researchers conducting the trial.To date, the trial has produced excellent results: indicating that the copper recovery has improved by about 2 percent. The successful application of high chrome grinding media to the Ernest Henry ore has increased metal value by $18.7 million USD per annum based on current spot price for copper.INTRODUCTIONTheoryThe application of electrochemically inert grinding media to mineral systems has been extensively studied (Table 1). Broadly, these studies indicate that most sulphide minerals are more noble than the grinding media used during comminution. Therefore, the sulphide minerals are cathodic with respect to the forged steel grinding media, and the following reactions apply:"

Jan 1, 2011

By Jeffrey W. Fergus, Shiqiang Hui

"Aluminum is an important alloying addition to the zinc used in the hot-dip galvanization of sheet steel to control the properties and appearance of the resulting coating. Optimization of the galvanization process requires control of the alloy concentration which can be improved through the use of chemical sensors. Aluminum sensors based on molten electrolytes are commercially available but are not widely used because of their high cost. One approach to reducing the cost is to use a solid electrolyte which can simplify the sensor design and thus reduce the cost of fabrication. In this paper, the development of an aluminum sensor based on a solid fluoride electrolyte, specifically magnesium fluoride, will be described.IntroductionThe concentration of the zinc bath used in hot-dip galvanization affects the galvanization process as well as the properties of the resulting coating. Thus, accurate in situ measurement of the alloy composition can be used to improve process control. This paper describes a solid-electrolyte-based aluminum sensor for monitoring the bath composition during hot-dip galvanization."

Jan 1, 1997

By Gregg W. Davidson, J. Andrew McGlenn, Frank Huber

The Second Narrows Water Supply Tunnel will ensure system reliability in the event of a major earthquake and increase the Greater Vancouver Water District’s capacity to meet the long-term needs of a growing population. The tunnel will be 1,100 m long and 6.5 m in diameter (3,610 LF × 21.3 ft), constructed under Burrard Inlet between North Vancouver and Burnaby in British Columbia. It will be excavated through mixed ground conditions under high groundwater pressure, using a slurry TBM, between a 72 m (236 ft) deep shaft in soil and a 110 m (361 ft) deep shaft in rock. The completed tunnel will accommodate three large-diameter water mains that will be installed as part of the tunnel contract. This paper presents the project from design and contractor procurement, into the current construction stage describing some of the unique challenges encountered during the project development to date.

Jun 13, 2021

By Yuuki Yoshida

Electrolytic manganese dioxide, EMD, is the positive electrode material of primary batteries and the raw material of LMC used as the positive mass of lithium ion batteries and is currently produced by anodic deposition on and harvesting from a titanium anode in acidic manganese sulfate solutions prepared by dissolving high purity of manganese sulfate into sulfuric acid solutions. This paper presents an alternative method of EMD production using a novel anode, Mn2O3 coated titanium, at lower operating temperature than the current process to explore a possibility of manganese recovery from zinc electrowinning solutions. The Mn2O3/ Ti anode prepared by thermal decomposition of a precursor solution containing Mn (II) showed the anodic deposition of MnO2 by constant current electrolysis and the current efficiency was 95% in maximum, while the current efficiency and the crystallographic structure of deposited MnO2 depended on the current density, the electrolysis time, the bath temperature, and the concentration of Mn(II). The deposited MnO2 was successfully harvested from the anode and the recovery rate was 98%.

By ETHAN FUSTER, Richard Ray Jr, STEPHEN LEE

The abstract states that horizontally-mounted jet fans are commonly used to ventilate vehicular tunnels due to their space and cost savings compared to fully ducted systems. It highlights the successful use of vertically-mounted jet fans in exhaust ventilation shafts for a passenger rail overbuild in New York City. The paper compares shaft dimensions, jet fan placement, and measured airflows, also comparing these measurements to predictions from computational fluid dynamics (CFD) simulations.

Mar 16, 2022

By H Kurth

Oyu Tolgoi copper and gold mine in the southern Mongolia holds mineral resources that make it one of the largest known copper and gold deposits in the world. The project is operating an open pit mine on the near surface of Southern Oyu deposit and developing underground block-caving mine at the Hugo Dummet North where 80 per cent of total resources exists. Oyu Tolgoi (OT) commenced open pit mining in 2011 and implemented an industry standard blasthole sampling, and ordinary kriging grade control estimation with block-out process. Since 2017, grade control improvement projects have successfully completed that have led to the implementation of current, improved grade control system. Geological model is updated by blasthole logging on Leapfrog® and used for daily grade estimations. GC estimation is proceeded solely on Vulcan® by running Lava script and integrating with a relational database. Combination of block-out procedure produces GC model which is updated in Vulcan® and as well as in the database simultaneously. Switching to the integrated database eliminated many manual processes such as importing and exporting data and enabled access to the database anytime, anywhere and from any device. Thereby, these improvements allowed to increase an efficiency, create a comprehensive reconciliation system and reduce operational risks. We are looking forward to expanding applications of integrated grade control data stored in the database. This paper outlines how the grade control system was developed at OT’s open pit mine, and how it is integrated into the short range mine planning, mine reconciliation workflow and ultimately enabled development of various automated reporting systems.

Mar 22, 2022

By Yoshihiko Maeda

It is said that the 21 st century will be an era of the remedy of the global environment. In order to reserve natural resources for the future and to avoid the dispersion of heavy metals after usage and to avoid pollution problems, it is extremely important to recycle heavy metals as much as possible by reasonable recovery procedures. The nonferrous metal industry is expected to play a important role in the recycling of heavy metals that are originally their products. From the depressed metal price experienced in Japan in 1980th due to the sudden change in current exchange rate between US dollar and Japanese yen, one of major nonferrous metal company, Dowa Mining, has diversified its business area not only to the so-called down stream, but also to the environmental business including metal recycling, industrial waste treatment and soil remediation by utilizing technologies and facilities once used or still used for mining and smelting of copper, zinc, lead and precious metals. In this paper some of these applications will be presented.

Jan 1, 2003