Search Documents

By Cuthbert Musingwini, Adeodatus S. Nhleko, Mahlomola I. Mabala

Optimization of a three-dimensional (3D) underground stope layout is complex given the number of variables and constraints to consider, such as the stope size. Determination of the appropriate stope size in stope layout optimization problems is a complex process that must consider several factors including placement of infrastructure and development, production scheduling, and equipment selection. An inappropriate stope layout can result in unrealistic expectations for a production schedule, consequently negatively affecting the derived economic value. Therefore, this paper used a dual interchange algorithm (DIA) to evaluate the effect of stope size on the stope layout economic value (SLEV) for a synthetic Platreef mineral deposit planned for extraction using sublevel open-stoping. The results showed that generally as the stope size increases, the SLEV decreases. This aligns with practical mining because larger stope sizes have a higher chance of incurring more dilution which reduces economic value, while smaller stope sizes enable more flexible extraction where unprofitable blocks can be left unmined as waste, thus increasing the derived SLEV.

Jun 25, 2023

By K. Luxbacher, D. T. Hristopulos, S. Schafrik, J. Diaz, Z. Agioutantis

Big data is generated from both surface and underground mining operations. Such data contain a wealth of information concerning safety and health in the workplace and production parameters. This paper will discuss the progress towards developing an accurate forecasting model for methane gas concentration based on the analysis of data collected from Atmospheric Monitoring Systems in underground coal mines employing time series models. Several procedures need to be applied to raw data, such as data cleaning and filtering for outlier removal, data homogenization and segmentation, and exploratory statistical analysis. The data analyzed were retrieved from two coal operations in the Eastern US. A negative correlation between barometric pressure and methane gas concentration was established, at least for certain data segments. Such correlations raise the possibility that barometric pressure data can predict variations of gas concentration in the mine. The datasets will be further investigated to establish the robustness of barometric pressure and gas concentration correlation and explore the dependence of gas concentration on other factors related to mine design and operations

Mar 2, 2022

By Patrick Tassot

Increased worldwide highly competition in steel market imposes innovative measure for the steelmaker targeting cost reduction and climate-friendly steelmaking process in order to have the ability to withstand the pressure of the market. At the same time the demand for high purity and highest quality steels continues to grow from year to year, especially in the sector automotive in transportation of oil and gas, in the construction Industry and in the manufacture of heavy plate. As they allow producers to be up to the requirements while allowing expanding their product mix, new secondary metallurgical treatments have become a must additionally to standard equipment elements of steel plants modern. Most of these treatments occurs in the steel ladle increasing the pressure to ensure a reliable and as possible neutral reactor. Intelligent solutions for refractory lining ladles should integrate better adaptation to the operational process parameters and the high reliability/availability at the best cost/performance. This challenge has conducted Refratechnik to develop new concepts to overcome the frontier between shaped and unshaped materials and that’s what will be covered in this paper.

Aug 17, 2017

By J. D. Defilippi, E. M. Gilbert, K. G. Brickner

FCC chromium-manganese-nitrogen (Cr-Mn-N) steels differ from most other fcc materials in that these steels undergo a ductile-to-brittle transition. Transformation to martensite is considered to be responsible for this behavior in some metastable Cr-Mn-N steels. However, very stable Cr-Mn-N steels also exhibit a ductile-to-brittle transition. The results of this study indicate that deformation faulting is the probable cause of the brittle behavior of stable Cr-Mn-N steels. Deformation faulting accounts for the ductile behavior of these steels in a tension test at -320°F and brittle behavior in an impact test at -320°F. Deformation faulting also accounts for the toPological features observed on the fracture surfaces of impact specimens of these steels. FACE- centered- cubic chromium-manganese-nitrogen (Cr-Mn-N) steels differ from most other fcc materials in that these steels undergo a ductile-to-brittle transition. Many Cr-Mn-N steels transform to martensite during deformation,l-5 and several investigatorsl-3 have suggested that the brittle behavior of these steels is caused by martensite formation. However, very stable Cr-Mn-N steels also exhibit brittle behavior. Schaller and Zackeyl reported that a very stable Cr-Mn-N steel (less than 3 pct martensite formed at -320°F) exhibited a transition temperature higher than that for steels in which large volume fractions of martensite formed during testing. The explanation given by Schaller and Zackey for this observation was that in the very stable steel the martensite, because of its higher interstitial content, was more brittle than that formed in their other steels. This explanation was questioned by Tisinai and samans4 and Baldwin.6 Moreover, because the toughness of stainless martensite at cryogenic temperatures is generally very low, this explanation does not account for Thompson's7 observation that small additions of nickel (1 to 3 pct) greatly improve the toughness of high nitrogen (0.35 pct) Cr-Mn-N steels. The present paper summarizes the results of an investigation of the low-temperature brittleness in very stable Cr-Mn-N steels. The importance of the mode of deformation on the toughness of these steels is discussed. Table I. Compositions of the Steels Invertigated, Pet Steel C Mn P S Si Ni Cr N - A 0.09 14.70 0.018 0.011 0.47 0.22 18.40 0.54 B 0.12 14.90 0.001 0.008 0.48 0.14 17.80 0.38 C 0.12 14.95 0.004 0.005 0.62 3.95 18.43 0.38 MATERIALS AND EXPERIMENTAL WORK The compositions of the steels investigated are shown in Table I. Steels A and B had compositions within the limits of a proprietary Cr-Mn-N stainless steel,* whereas Steel C was similar in composition to the proprietary steel except for its 3.95 pct Ni content. All steels were hot-rolled to 1/2-in. thick plate. The plates were subsequently annealed for 1 hr at 2000°F and water-quenched. Standard longitudinal and transverse Charpy V-notch impact specimens were machined from the annealed plates. Duplicate longitudinal and transverse impact specimens were tested at 212", 80°, 32", 0°, -100°,-160°,-200°,-256", and -320°F. Longitudinal tension-test specimens were also machined from the plates and tested at a crosshead speed of 0.05 in. per min at the aforementioned temperatures. The fractured impact and tension-test specimens of all three steels were examined to determine whether martensite had formed during testing. Magnetic, X-ray, electron-diffraction, and electron-microscopy techniques were used to detect the presence of martensite in the highly deformed areas of these specimens. Metallographic examination of highly deformed areas of impact and tension-test specimens revealed the presence of dark-etching bands, such as those shown in Fig. 1. These bands were observed only in deformed samples and were thought to be associated with the low-temperature brittleness of the Cr-Mn-N steels. Accordingly, a sample 1 in. wide by 3 in. long was cut from the 1/2-in.-thick plate of Steel C. This sample was surface-ground to a in. and then cold-rolled 60 pct at -320°F. Thin foils were prepared from the cold-rolled sample and examined in a JEM electron microscope. Brightfield, dark-field, and selected-area diffraction techniques were used to determine the cause of the dark-etching bands. Fractographic experiments were also performed. Impact specimens Of Steels A, B, and C were broken at -320oF, and the fracture surfaces of these specimens were immediately shadowed with carbon. The carbon replicas were examined in a Siemens electron microscope, and attempts were made to correlate the topological features of the fracture surfaces with the deformation mechanisms that could be occurring during an impact test of these steels.

Jan 1, 1970

By Marcio B. Fonseca

Nickel-cobalt laterite deposits have become the focus of attention for hydrometallurgical processing. Following the lessons of the second generation high pressure acid leach (HPAL) projects in Western Australia other Ni-Co laterite projects are now evaluating potential HPAL projects with a rigorous integrated approach that begins with geological modeling, resource estimation and metallurgical studies. The Vermelho nickel-cobalt laterite deposit has been under exploration and study for several years with investigations of various metallurgical processes. Recent HPAL studies have indicated that the nickel and cobalt laterite at this deposit is amenable to upgrading by silica rejection followed by pressure leaching. These studies have required a detailed geological investigation to generate a new resource model. The recent development of a sophisticated geological model integrated with a multi-element resource estimation for this complex tropical nickel laterite deposit in northern Brazil provides an example of the contribution of geology at the critical project stage where process technology decisions are made on relatively small samples of the total resource.\ Keywords: Ni Laterite, Geological Modeling, Resource Estimation

Jan 1, 2004

Datun Concentrator currently processes complex sulfide ores in Gejiu Municipality, Yunnan Province, China. The ore contains much higher arsenic than other ores. The run of mine ore is fed to the concentrator to recover copper and tin by bulk flotation and gravity concentration, and then the other sulphides, such as pyrite, arsenopyrite, etc. didn?t get utilized and are discarded as tailings due to the high arsenic content. In order to utilize the pyrites in the tailings, a series of tests have been conducted for finding the solution of arsenic removal from high arsenic-bearing pyrite concentrates through simple flotation process. By means of orthogonal experimental design, the optimized levels and main factors have been found out for the roughing stage. Through selection of the effective in-organic depressants for the arsenic-bearing minerals, the arsenic in the pyrite concentrate can be removed to meet the requirement of sulfuric acid plant (As%=0.5%) by the open flotation process, i.e., one-time roughing and two-time cleaning.

Jan 1, 2014

By A. Himsley, E. Byleveld

"With reference to the chemical constraints underlying the ion exchange process for uranium recovery, a generalized view is presented on the actual and the achievable efficiency of the process. The area considered is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution.A comparison between actual plant results and the chemical requirements shows that:(a) Unless new and better ion exchange resins are developed, no dramatic change in equipment size and resin inventory is""anticipated. (b) Elution efficiency, especially for sulphuric acid, may be improved considerably. More concentrated eluates may beproduced at lower chemical consumption. A possibility of achieving additional purification solely by ion exchange is discussed.IntroductionThis paper presents a generalized view of the actual and the achievable efficiency of the ion exchange processes for urannium recovery. The study is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution. The ultimate efficiency attainable with ion exchange is dietacted by the chemical reactions underlying the process. The most sophisticated technology cannot change the diffusion rates in the ion exchange resin nor make the uranium loading exceed its equilibrium valueThe design of an ion exchange plant for uranium recovery involves a considerable number of parameters as a result of the wide variety of pregnant solutions produced from different orebodies. Therefore, a generalized approach of the ion exchange process inevitably neglects some parameters which maylead to significant variations in apparently identical situations.The uranium concentration in the pregnant solution, together with its pH, are the principal variables which determine resin loading and residence rime in the ion exchange system. On the elution side, the type of eluant and its concentration will determine the contact time required and the amount of eluant needed to strip the resin. The temperature, the properties of the ion exchange resin, the total dissolved solids in the feed solution and the competing ions are other variables that affect the chemical performance; these, however, may be considered as a correction of the principal parameters if one is interested only in general trends."

Jan 1, 1980

By Pekka Hanniala

The Outokumpu Flash Smelting process today is the most feasible method for copper matte smelting. The economic feasibility of the process has always been one of the main decision making criteria in smelter projects. Thus, today about 50 % of the world primary copper production utilizes Outokumpu Flash Smelting Technology. However, in the future, environmental criteria will have stronger and stronger impact on decision making. Flash Smelting technology offers the best pollution control features of any process. today. It is foreseen that, in the near future, the global trend will be that all the smelters must decrease their emissions at an accelerating rate, compelling the smelters to make increasingly larger investments on environmental protection. In most of smelters ?today, Peirce-Smith converting and transfer of the molten material in ladles are the number one pollution source. The key today for copper converting and minimizing emissions is the Kennecott-Outokumpu Flash Converting process, which has proven to be the most effective converting method in terms of pollution control and, production efficiency including capital and operational costs. Outokumpu Flash Smelting technology is applicable also for small to medium scale smelters but the most interesting area is the upper capacity limit for smelting in one line, which has not yet been reached. We predict that by the year 2000 to 2005, there will be at least one smelter which produces 500,000 tonnes of Cu per year based on one Flash Smelting and Flash. Converting unit. The current state-of-the-art of the Outokumpu Flash Smelting - Flash Converting process is presented in this paper as well as some new options for copper production to be utilized in the near future but which are available already today.

Jan 1, 1998

By Ri McCrindle

"Analytical Chemistry is moving rapidly towards a concept where technicians have to do no more than press a button and print the result from an instrument that is a featureless ""black box"". In this environment we must ask how much traditional ''wet chemistry"" is still required for undergraduate students.Methods that can be fully automated will become increasingly important. An example of such a method is that of the slurry nebulisation and ICP-OES analysis of precious metal concentrate. Grinding the sample and adding Triton X100 as dispersant, complete analysis time is in the order of 90 min as apposed to the traditional Carius tube method which could take as long as 24 h. For most of the elements studied, the results using ""in-house"" reference material for calibration and as samples as well were within the 95% confidence level. Elements of low concentration in the sample (As, Bi and Se) were not within that level."

Jan 1, 2014

By J. R. Coleman, G. L. Corrigan

FOUR factors that largely determine the end product obtained when cement and water are mixed are the chemical composi-tion of the cement, the fineness to which the cement is ground, the amount of mixing water used, and the procedure used in mixing the slurry. In order to study the effect of two of these factors, the other two, the chemical composition and method of mixing, are kept constant, leaving as variables fineness and water-cement ratio. Through years of experimentation and usage it has been well established that the reduction of cement clinker to a very fine state by grinding improves its cementing value, principally because the reaction between cement and water takes place only at the surface of the cement particle, further action being hindered by the accumulation of reaction products that tend to coat the unreacted material. Therefore, the moE finety-ground %cement, and the greater the surface exposed in propor-tion to its mass, the more rapid is the The work covered by this paper was done by the authors in pursuance of graduate studies in the ~epartment of petroleum Engineering at The University of Texas. The present paper is a condensation of a more detailed DaDer from which, for brevity, information such as the procedure for determining permeability and some of the discussion and procedure relevant to slurry volumes and fineness of cement have bsen deleted. It was felt that this information would not be of interest to most readers and should be outside the scope of this paper. Manuscript received at the office of the Institute Aug. 16, 1940. Issued as T.P. 1266 in Petroleum Technology. January 1941. hydration rate. Similarly, the greater the surface exposed, the greater the proportion of the cement that reacts, and the lower the amount of residue that is unreacted and so remains inert and unable to make any contribution to cementing properties.] Although it is more expensive to manufacture a finely ground cement than a coarser cement, the advantages of fine grinding of construction cements were so marked that the fineness of cement has increased considerably in past years. When the manufacture of special oil-well cements was begun, it was necessary to consider properties of cement that previously were considered of minor importance, foremost of these being pumpability. Since, with the water-cement ratio constant, a finely ground cement will produce a neat slurry of higher consistency and shorter time of pumpability than will a coarser cement, there is a tendency to grind oil-well cements to a lower degree of fineness. Therefore, in order to produce oil-well cements that will make a slurry having a long time of pumpability, cements are manufactured that because of their coarseness generally are Poorer cementing materials than some of the more finely ground construction and on the other hand, often it is necessary to Pump oil-well cements for long periods of time to place them properly behind a string of casing in a deep well, and since high strength is not of foremost importance for such cement, there is room for considerable controversy concening the proper fineness range.

Jan 1, 1941

By G. L. Corrigan, J. R. Coleman

FOUR factors that largely determine the end product obtained when cement and water are mixed are the chemical composi-tion of the cement, the fineness to which the cement is ground, the amount of mixing water used, and the procedure used in mixing the slurry. In order to study the effect of two of these factors, the other two, the chemical composition and method of mixing, are kept constant, leaving as variables fineness and water-cement ratio. Through years of experimentation and usage it has been well established that the reduction of cement clinker to a very fine state by grinding improves its cementing value, principally because the reaction between cement and water takes place only at the surface of the cement particle, further action being hindered by the accumulation of reaction products that tend to coat the unreacted material. Therefore, the moE finety-ground %cement, and the greater the surface exposed in propor-tion to its mass, the more rapid is the The work covered by this paper was done by the authors in pursuance of graduate studies in the ~epartment of petroleum Engineering at The University of Texas. The present paper is a condensation of a more detailed DaDer from which, for brevity, information such as the procedure for determining permeability and some of the discussion and procedure relevant to slurry volumes and fineness of cement have bsen deleted. It was felt that this information would not be of interest to most readers and should be outside the scope of this paper. Manuscript received at the office of the Institute Aug. 16, 1940. Issued as T.P. 1266 in Petroleum Technology. January 1941. hydration rate. Similarly, the greater the surface exposed, the greater the proportion of the cement that reacts, and the lower the amount of residue that is unreacted and so remains inert and unable to make any contribution to cementing properties.] Although it is more expensive to manufacture a finely ground cement than a coarser cement, the advantages of fine grinding of construction cements were so marked that the fineness of cement has increased considerably in past years. When the manufacture of special oil-well cements was begun, it was necessary to consider properties of cement that previously were considered of minor importance, foremost of these being pumpability. Since, with the water-cement ratio constant, a finely ground cement will produce a neat slurry of higher consistency and shorter time of pumpability than will a coarser cement, there is a tendency to grind oil-well cements to a lower degree of fineness. Therefore, in order to produce oil-well cements that will make a slurry having a long time of pumpability, cements are manufactured that because of their coarseness generally are Poorer cementing materials than some of the more finely ground construction and on the other hand, often it is necessary to Pump oil-well cements for long periods of time to place them properly behind a string of casing in a deep well, and since high strength is not of foremost importance for such cement, there is room for considerable controversy concening the proper fineness range.

Jan 1, 1941

By Seth C. Schaefer

The Bureau of Mines investigated the standard Gibbs energies of forma-tion AGfo, for NiCr204 (nickel chromite) and CoCr204 (cobalt chromite). High temperature galvanic cells employing stabilized ZrOz (zirconia) as the solid electrolyte were used to measure the open-circuit potentials for the cell reactions ?

Jan 1, 1986

For several decades miners have been obliged to maintain a vast supply of sharp steels at the working face to meet the hungry needs of rock-drills. In medium and large size mines this has meant the setting up of an organisation to store steels, to make and sharpen bits with all the complication and skill of forging, hot milling and heat treatment, and to transport sharp and dulled steels to and from the working face with all its labour, wastage, and inconvenience to other mining operations.In a mine with 250 rock-drills in use, a flow of more than 60,000 sharpened steels each month has to be maintained to keep the machines fully employed, so some idea of the magnitude of this problem may be grasped.For a long time it has been apparent that it is mainly the bit itself that wears, and many attempts have been made to reduce the enormity of the problem by providing detachable steel bits which could either be used once and rejected, or sharpened three or four times before rejection.At the same time metallurgists have striven to 'improve the quality of the steel and the heat treatment afforded it so that a bit, readily workable In a normal mine drill-shop, could be produced having a high resistance to wear and fatigue; but, although various alloy steels have been marketed, it is still usual to find many mines relying on a "straight" carbon (0.6 - 0.9% C.) steel for their drill steels.Since 1915 increasing use has been made of tungstencarbide as a cutting implement in the engineering industry. Where, on account of its great hardness and long life, it...

Jan 1, 1948

By M. Kinnunen

Handling of municipal solid waste (MSW) and control of its potential resources is becoming increasingly important in modern society. The OECD (Organization for Economic Co-operation and Development) average on municipal waste produced in 2003 was that of around 570 kg per inhabitant. In European Union countries around half amount is of MSW landfilled. In Finland still 88% of MSW was landfilled in 2004. Since incineration reduces MSW volume significantly while producing heat energy, it has become one of the most common waste handling techniques. The shortcoming of incineration is however, that incinerated MSW is often not pre-sorted and it produces slags and ashes as side streams from which recovery of metals is difficult. This paper looks into possibilities of scrap metal recovery for recycling from municipal solid waste incineration (MSWI) bottom ash. In order to do that, a flow sheet of physical separation methods was developed and tested with Finnish rotary furnace MSWI bottom ash. In addition, an empirical model for estimation of the recoveries of scrap metals with physical separation methods for treatment of MSWI bottom ash was developed. According to the results of this study, for 1 Mt of incinerated MSW with 30% mass reduction, a minimum resource potential of 100 kt for magnetic metal scrap of roughly 24 % grade and about 19 kt of non-magnetic metal scrap of roughly 65 % grade. In other words, 57 kg magnetic scrap and 12 kg non-magnetic scrap per inhabitant at the mentioned grades, respectively. Although wide variations of parameters affect the MSWI bottom ash quality, it can be said that a considerable amount of metals is drained into MSWI bottom ash. Results of this study show that from MSWI bottom ash significant material streams metal scrap can be reintroduced into the resource cycle which would otherwise be lost.

Jan 1, 2014

By D. Michaud, C. Bazin, S. Lévesque, L. Pérez-Barnuevo, H. Longuepée

In recent years, with the emergence of Geometallurgy, a great effort has been made to characterize ore resources as early and accurately as possible, to allow better design and a more efficient operation of mineral processing circuits. In this context, core logging plays an important role, since drill cores provide the first insight into the ore characteristics. However, to satisfy geometallurgical requirements, traditional core logging does not suffice. New tools and methodologies need to be developed for the automation of core logging and the acquisition of mineralogical data better related to mineral processing performances. In this paper, a methodology for the geometallurgical characterization of drill cores is proposed, based on the drill core textural patterns. Textural pattern is defined here as the macroscopic spatial arrangement of minerals. The Mont-Wright iron ore deposit (Quebec, Canada) is used as a case study. The first part of this work aimed at analyzing the potential link between the iron ores textural patterns observed in drill cores and their response to ore processing, namely comminution and concentration. Preliminary results show similar performances in terms of energy consumption and heavy liquid separation for samples showing the same textural pattern. In the second part, this work seeks to develop a methodology for the automated identification of drill core textural patterns by the application of digital image analysis and discriminant function analysis. The results obtained show that this methodology is able to discriminate between the textural patterns identified at Mont-Wright with a good rate of success. Therefore, this work lays the foundation for the development of a new drill core characterization tool, which would allow for the early prediction of the iron ore behaviour during mineral processing through the identification of drill core textural patterns.

Jan 1, 2016

By D. B. Dreisinger, M. Rasouli

"Developing technology to address the environmental hazards associated with selenium in mine-impacted waters has been a serious challenge. Ion exchange (IX) has been identified as a potential treatment technology. This paper begins with a review on selenium adsorption with commercially-available basic anionic exchangers (BAS). It then looks at the use of resins for selenium removal via modification with the addition of -O, -N, or -S-containing chelating ligands and chelating polymeric ion exchangers pre-loaded with immobilized metal cations. The synthesis of chelating exchangers requires a final product with a highly stable metal in the ligand-metal complex. The nature, oxidation state, size, and affinity of the metal for the target oxyanions and the size, degree of protonation and space configuration of the oxyanion are among critical factors affecting the oxyanion uptake. There is a limited number of studies on the critical parameters affecting the selenium affinity for chelating exchangers. Such a study could fill in the gaps of our understanding of selenium-metal-chelating ligand interactions and assist in developing a new ion exchanger. In addition to commercial IX resins, layered double hydroxide materials (LDH) have received attention for oxyanion removal from waste water. The adsorption capacity of the LDHs are affected by the crystallinity of LDH, the nature of metal components, the ratio of metals, charge and type of anion, and the space between the layers. In particular, the Friedel phase (FP), a member of the LDH family, showed high adsorption capacity for selenate removal from synthetic solution. A study is currently underway at the University of British Columbia to investigate the effect of different synthesis methods and aging on the suitability of FP for selenium removal from mine waste water."

Jan 1, 2017

By E. T. Tuzcu

In this manuscript, a new approach for modeling the rate of grinding process is explained. A review about grinding rate definitions so far is given and the possible ultimate way for grinding modeling is given as modeling the rate based on energy spectra. The traditional/phenomenological approaches for modeling size distribution of grinding mills give their place to a new generation modeling technique. Developments in the computational methods and necessity to model product size distribution of large mills, larger than ball mill size, paved the way for this novel technique. The traditional grinding rate models are mostly based on the back calculated breakage parameters from the experimental data. However, direct modeling of breakage parameters and hence the prediction of size distribution of the grinding mills may become possible with this approach. The material breakage data and discrete element method (DEM) energy spectra are the main components of this approach. Albeit the focus in this study is on modeling of breakage rate under impact mode of breakage, the abrasion mode of breakage was also tested by carrying out abrasion tests. Impact mode of breakage was analyzed using ultra-fast load cell device (UFLC) and drop weight tester. Dry tumbling test was carried out for abrasion experiments. Obtained material breakage versus energy data are combined with the collision energy spectra to obtain the breakage rate function. In addition, the material breakage versus energy information from the tests is converted into breakage distribution function. The model was verified in a lab scale mill (90 cm diameter-15 cm length). 10 to 15 kg of limestone was ground using 50 mm steel ball at varying conditions, i.e., rpm, volume loading. It is shown that the proposed model predicts all (1, 2, 4 min.) grinding intervals for all experiments highly accurate.

Sep 1, 2012

By Jason J. Crowder

Presentation Outline ? Introduction ? Costs of ground support and rehabilitation ? Why post-failure rock mass properties are necessary ? The Rock Mechanics Problem ? Present State of Modelling and Instrumentation in Mining ? Case Study Background ??Williams Mine ? Deriving Parameters for Modelling from Instrumentation ? Results from Case Study ??Back Analyses ? Discussion of Research Impact t Summary

May 1, 2006

By A. G. Doll

"Multi-stage crushing plants, including high pressure grinding roll (HPGR) circuits, require more materials handling equipment than SAG and ball mill circuits. A temptation exists to neglect the energy consumption of materials handling when doing desktop comparisons of HPGR versus SAG milling circuits because estimation of materials handling power requirements can demand significant general arrangement drafting that is not available when performing preliminary scoping or ""desktop"" studies.The largest component of materials handling power is consumed by conveyors when lifting material between stages of crushing, meaning that a simple potential energy model can be used to evaluate conveying specific power consumption. This potential energy consumption for conveying can then be factored to provide overall materials handling specific energy consumption suitable for desktop studies of HPGR and other multi-stage crushing circuits. The technique also permits different crushing circuit flowsheets to be evaluated, at a preliminary level, by simply counting the number of times a conveyor must ""lift"" ore from ground level up to a bin or other equipment mounted up high.INTRODUCTIONTrade-off studies of multi-stage crushing plants involving high pressure grinding rolls (HPGRs) versus semi-autogenous grinding (SAG) mill circuits typically focus on the operating cost savings of crushing plants versus the capital cost savings of SAG mill plants. Very high-level (or desktop) studies of this type do not include a great deal of engineering work, meaning that the details (and costs) of ancillary systems are often not captured when doing the comparisons. The more complicated nature of the multistage crushing plants means there are more ancillary systems than a SAG mill plant, risking a skewed analysis of the operating costs, benefiting the HPGR option.One of the ancillary systems that may be overlooked is the more complicated conveying systems inherent in multi-stage crushing plants. Due to the mass of material being handled in large mining operations, these conveyors become a significant portion of the operating costs. A simple way to estimate the specific energy consumption of conveying systems without requiring engineering drawings and a site layout would allow high-level studies to capture this operating cost."

Jan 1, 2015

By W. A. Backofen, A. T. English

The kinetics of re crystallization were determined metallographically for a 3-1/4 pcl Si-Fe rapidly compressed at temperatures of 710° to 911°C, and held for various times at the working temperature. As in re crystallization following cold wwk, the time for re crystallization was reduced by increased temperature and strain. Nucleation occurred chiefly at grain edges, although other pre-existing interfaces, notably inclusions, also served as nucleation sites. The importance of intragranular nucleation to grain refinement in hot working is pointed out, together with some possible techniques by which nucleation might be induced within the grains. The observed isothermal growth rates are quite accurately described by the equation G = 4 x 10-'/t (cm per sec), independent of temperature and strain at all but the shortest times. Changes in G during recrystalliza-tion can exceed two orders of magnitude. It is argued that release of stored energy associated with lattice defects cannot adequately explain the time dependence. A suggested alternative involves processes of solute segregation and desegregation in the unrecrystallized matrix and at the moving boundary, respectively. EFFORTS to improve hot-working practice are hampered by an incomplete understanding of the fundamental metallurgy involved. Research directed at establishing the required basic foundation falls into two categories, the first concerned with measurement of mechanical properties under the conditions of high temperature and strain rate which characterize such processing, the second focused on structure and its relation to the deformation conditions. Rossard,' Rossard and Blain,2 and Hardwick and Tegart have conducted many high-speed, high-temperature torsion tests on various metals. One of their objectives was interpretation of stress-strain curves in terms of the structures of specimens rapidly quenched following interruption of twisting. They showed that appreciable hardening occurred in the early part of the test, and that this hardening reflected the concurrent development of an increasingly dense substructure within the grains. The detailed nature of this substructure was observed to depend on the ease of polygonization which, at least in fcc metals, varies with the stacking-fault energy.= By holding specimens after interruption but before quenching, the nucleation and growth of new grains could also be studied. Some success has been realized in relating the microstructure of hot-rolled steel to its temperature:strain rate:strain history with such testing.' The same general observations have been made by others investigating rolling4f5 and drop-hammer forging.~-~ Incident to these experiments, some efforts were made to determine the kinetics of re-crystallization as well as the velocity of the migrating boundaries. The results have been largely qualitative, owing to difficulties of interpreting hardness measurements5 and microstructures. The work described here was undertaken to obtain more quantitative information from tests on a material having suitable metallographic properties, and, in this way, to provide further insight into the fundamentals of this practically most important kind of deformation processing. I) MATERIALS AND EXPERIMENTAL TECHNIQUES Materials. Electrolytic etching of a Si-Fe alloy reveals dislocations and substructure in unrecrystallized grains.8'9 This unique characteristic makes possible a precise determination of the extent of recrystallization. For that reason, it was the material selected for all experiments in the present work. The two particular alloys that were used are identified in Table I. A major difference between "A" and "B" is the number of inclusions, as noted in the table. Most of the experiments were made with material "A". It was received as hot-rolled plate 1 in. thick, sawed to 2-in. widths, hot-forged at 1200°C to 5/8-in. rounds, and finally annealed in a mechanical vacuum at 1000°C for 24 hr. The result was substructure-free grains of mean diameter 0.05 cm.*

Jan 1, 1964