Search Documents

By D. A. Summers, C. J. Haas, G. B. Clark, J. W. Brown

While significant advances have been made in excavation of rock, largely in improvements in drilling, blasting, loading, and haulage, conventional operations have been improved until little feasible increase in efficiency or rate of advance appears possible. Tunnel-boring machines have been developed which will excavate at rapid rates in soft to medium- hard rock. Hypervelocity impact is being intensively investigated as a possible means of cutting and breaking rock, as well as lasers, electric current, explosive drilling, high frequency vibration, etc. The current development and use of high-velocity small-diameter water jets, metallic jets, and projectiles of various materials involve ultra-high-pressure phenomena of fundamental interest. Rock disintegration by water jets has been investigated in the USSR for over a decade. Large-diameter jets of low velocity are used to mine coal, and high-velocity capillary jets will cut and break rocks under laboratory conditions. Velocity ranges for breaking and cutting are dependent upon rock and jet properties, and pulsed jets break some rocks more easily than continuous jets. Spectacular laboratory results have been reported for breakage of unconfined blocks of some types of rocks. Compressors, pressure multipliers, gas explosion chambers, and water cannons have been used to generate jets. Jet properties, such as continuity, unit pressure, total pressure, and stability have been measured. Results agree with theory, although the latter has been established only for relatively low-velocity flow. Diameter, speed of traversing, and frequency of pulsed jets affect rock response. Investigations in Britain have only recently begun consideration of harder rocks and higher velocities, although water jet cores have been found to be more continuous at lower velocities than previously believed. Lower limits of jet velocity for rock cutting were established for the rocks investigated.

Jan 1, 1970

By V. I. Lakshmanan, Dan A. Mackie

Traditional vat leaching methods have had limited success, primarily due to the high cost of loading and unloading the vats. In general, such batch methods are labor-intensive and costly. Heap leaching has emerged as a viable, low- cost alternative, but low recoveries, normally in the 70% range, offer opportunities for improvement. Also increased regulatory guidlelines for effluent and spent heap leach pads disposal offer potential for alternative methods. The Mackie Vat Leaching Jig (MVLJ) has had its incubation at Ortech International, where bench scale through pilot scale testing continues. Design developments and testwork over the past two years indicate that the time may be right for field trials.

Jan 1, 1990

By Bonnie Cooper

3D printing by fused deposition can be used on lunar soil. The soil can be precisely size-separated to make the 3D printing process work efficiently. Using a MASER instead of a LASER would allow us to use the finest fraction of lunar soil, AS-IS, to manufacture things on the Moon.

May 1, 2013

By S. R. LaBrooy, J. Avraamides

Thermal reactivation of eluted carbon is an essential part of most carbon-in-pulp gold recovery plants. The effectiveness of the reactivation procedure depends on the nature and level of contaminants adsorbed on the carbon, the efficiency of the elution and the temperature, residence time and atmosphere within the kiln. The most commonly used kilns are evaluated in terms of their operating parameters and performance. Data obtained both in the laboratory and in the field emphasize the importance of carbon feed moisture content, kiln atmosphere and carbon conditioning on the activity of the kiln product.

Jan 1, 1998

By Fouad Faraj

For every blast pattern, zones of unique material types need to be classified before mining. Most material types can be summarized into different kinds of ore and waste. Blocks generated from blasthole assays are too small to be selectively mined so areas with a single material classification meeting the mine’s selective mining unit must be defined. Current industry standard practices are to manually draw ore/waste dig limits but this process is subjective and results in quantities of dilution and ore loss which can be improved upon to enhance the profitability of mining operations. Two weeks production data from a homogeneous Cu porphyry and heterogeneous Manto-type Cu deposit are used to assess the variability in the hand-drawn dig limits for 20 geologists, mining engineers, or ore control specialists and are compared with the optimal ore/waste delineation. The profit for 20 distinct hand-drawn dig limits for the homogeneous mine ranged by 3.7% from $10.5 million to $10.9 million averaging at $10.8 million. The percent range nearly doubled for the more heterogeneous mine at 5.9% from $17.9 million to $19.0 million averaging at $18.6 million. Using the optimal ore waste delineation, the profit increased to $11.0 million (1.9% increase) and $19.3 million (7.0% increase) for the homogeneous and heterogeneous deposits respectively. The natural variability, diggability requirement, and selectivity are identified as the main drivers of ore loss and dilution. Recommendations are provided for reducing the subjectivity in manual hand-drawn dig limits by integrating dig limit optimization algorithms as a tool to assist practitioners.

Feb 23, 2024

By S B. Sheldon

Wall control programs tend to be expensive and consequently require financial justification in order to get approval for the expenditure required. The difficulty faced in getting this approval is that the outcomes of a wall control program are all subjective – a prediction of wall stability and what the wall would do with and without the program. Determining a net benefit is difficult and often justification of a wall control program is based on gut feel, history and a good selling campaign to build a perceived need.This paper outlines a simple solution to this problem by applying risk management principles to wall control. The process is to identify the risks to the operation associated with current wall conditions and then build a risk database for different potential scenarios for each risk. A financial impact is assigned to each risk scenario to complete the database. A consequence and likelihood analysis of each of the risks is undertaken and a formula applied to estimate the projected cost to the operation for the current risk profile. The process is repeated for the predicted wall control conditions after the application of the wall control program. A successful wall control program will reduce an operation’s risk profile so this projected cost should be less than that calculated for the current scenario. The difference in the two projected costs is the value that the wall control program has produced and this value can be used to determine the net financial benefit potential for the wall control program.This methodology can also be applied to other improvement programs that focus on risk reduction such as vibration control.

Nov 8, 2011

By C. H. Larsen

The results of a comprehensive investigation of conveyance arrestment devices (safety catches) in United States coal mines are presented. Availability and use, performance, inspection, maintenance, testing, procedures, and regulatory requirements were investigated. Information was obtained from equipment manufacturers, mine operators, and regulatory-agency personnel, as well as from studies of domestic and foreign mining safety regulations. Traditional mine hoists and commercial elevators for mine use were investigated. Results of this and an earlier study of wire-rope practice in United States coal mines show a continued need for conveyance arrestment devices. A wide variety of these devices are in use. Only two types have been proved reliable for stopping a conveyance without injuring passengers or equipment. These are elevator overspeed-actuated wedge-clamp (Type B) safeties and broken-rope-actuated devices for wooden guides using a single-tooth-dog design developed in Ontario as a braking element. Elevators are widely used in U. S. coal mines. When maintained according to American National Standards Institute (ANSI) Specifications A17. I and A17. 2, they appear to present no major arrestment problems. Of 42 coal-mine hoists used for man transport that were inspected, 30 are in vertical and 12 in inclined shafts. Twenty-four vertical shafts use wood guides; 6 use steel. The 12 inclined-shaft systems use flanged-wheel T-rail guidance. Two wood-guided vertical-shaft systems use the single-tooth Ontario-type dog; the other 22 use multi-toothed wedges, cams, or dogs that have been proved highly unreliable. The arrestment devices in the six steel-guided vertical-shaft systems and in six of the inclined-shaft systems cannot be evaluated because performance data are lacking. The remaining six inclined-shaft systems have no arrestment devices at all. Of the 36 hoists with arrestment devices, the devices of 16 are never tested, the devices of 10 are actuated periodically with the conveyance at rest, and the devices of the other 10 are actuated periodically with a slow-moving conveyance. Although high speed is as probable as low speed in an emergency and would provide the best test of arrestment capability, no tests are performed in the United States which demonstrate the ability of an arrestment device to stop a loaded conveyance from high speed. Mine operators indicate little confidence in their conveyance arrestment devices, and manufacturers recognize a need to improve their products. Neither state nor Federal regulations provide a guide to this improvement. Mine operators, manufacturers, and state and Federal regulatory agency personnel would welcome specific guidance. In view of this, a set of application, design, actuation, stopping-performance, and testing and inspection criteria is presented as a guide to eliminating the inadequacies of these devices. Recommendations are included for improving hoist controls and machinery directly affecting conveyance safety.

Jan 1, 1972

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1980 (October 1, 1979 - September 30, 1980) under its Minerals Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the system technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1980

This publication summarizes, for potential contractors and all other interested parties, the research and development of in-house and contract projects programmed by the Bureau of Mines for fiscal year 1983 (October 1, 1982-September 30, 1983) under its Health and Safety Technology program. The objective of these projects is to provide an ordered and sequenced series of advance toward the Bureau's overall goal of providing the systems technology required to create a more healthful and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1982

By P. Balachandran

The paper outlines the existing facilities and working practices at the Khetri electro-refinery of Hindustan Copper Limited. Plans have been drawn up to mechanize some key operations to improve the quality of cathodes and the working environment as well as economize the refinery operations. The economic analysis for determining various optimum operational parameters under conditions existing in India have also been outlined. The impact of capacity utilization and mechanization under different sets of conditions on operational costs have been highlighted.

Jan 1, 1987

By Philip G. Meikle

The Bureau of Mines Coal Mining Technology program has developed new concepts aimed at improving the efficiency of underground coal product ion. Conceptual designs have resulted in equipment prototypes, some of which are currently undergoing proof-of-concept evaluations at Bureau and cooperator facilities. Several of these systems and concepts are described.

Jan 1, 1984

By Joern Katzer

It is vitally important to any tunnel project to have an accurate and reliable survey control network inside the tunnel for layouts, as-built surveys, and to provide guidance to the tunnel boring machine (TBM). However, the concepts and methodology to provide such a survey network are sometimes not well understood. For example, the first anticipated survey task that takes place during the bidding process is often ignored, which is to provide a comprehensive survey network preanalysis for the surface network and tunnel traverse based on survey statistics that will be used to make informed decisions on the survey requirements and methodology. Instead, these steps are often only vaguely based on previous results and prior tunneling experience. But each tunnel is different, and a solution that worked for one tunnel project might be unsuitable for another. The purpose of this paper is to provide tunnel project engineers, managers and surveyors with the general concepts for tunnel survey methodologies and examines several statistical tools for a basic horizontal and vertical tunnel survey preanalysis. These survey statistics tools provide useful estimates of the expected lateral and vertical tunnel traverse accuracies, but are not a replacement for a comprehensive tunnel network preanalysis. The proposed formulas do not take centering errors into account, are using average distances for each traverse leg, and assume that the survey data is free of outliers in the measurements. It is very important that the estimated instrument accuracy is based on true values that are reflective of measurement precisions that are actually achievable inside the tunnel to provide accurate results.

Dec 1, 2022

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By R. T. Swinderman

This paper discusses how many of the common practices in conveyor specification and design are out of date compared to the current expectations of users for safe, serviceable, reliable, and fugitive material-free conveyance of bulk solids. Ten of the most common mistakes made in the specification and design stages related to user expectations are reviewed along with the cost vs. price implications of those decisions. A general specification and design hierarchy that designers can use to improve conveyor design is included.

Jan 1, 2010

By E. Morrice

The metallurgical laboratory data developed in this study indicate an improved electrowinning process for producing higher purity cerium ingot. A typical sample of the Reno electrocerium contains 99.9 weight-percent cerium and the following impurities: Total other rare-earth elements, less than 0.04 percent; iron not detected; silicon and aluminum, less than 0.02 percent each; calcium plus magnesium, less than 0.01 percent; carbon, 0.01 percent; oxygen, 0.002 percent; hydrogen, 0.0003 percent; and nitrogen, 0.0015 percent.

Jan 1, 1960

By Xiaojing Li, Yueyuan Zhou, Shengyao Ma

The paper presented the acnalysis of field intensity of rare-earth permanent magnet with high BH product and the research of magnet configuration with narrow pole pitch on open magnet surface, both using ANSYS. The possibility to separate micro-disseminated feebly magnetic minerals by improving the field intensity and the capture line distribution rate on open magnet surface were verified. The research on the method to pile up magnets to increase peak value of field intensity on the open magnet to 1.0T was done through correlation analysis between shape and dimensions of magnetic material and field intensity. And the research on technology method to improve capture line distribution rate in the separating field to 1.25×105/m2 was done through optimization design of magnet configuration of the open magnet with narrow pole pitch. Laboratory tests were performed with hematite sample from ore dressing plant such as Hainan mine, Qidong iron ore, etc. The separation results acquired were at the same level as using the electromagnetic separator, verifying the possibility to separate micro-disseminated feebly magnetic minerals with open magnet. The research suggested a new idea about the development of magnetic separator with high efficiency and low costs to separate feebly magnetic minerals and non-magnetic gangues.

Jan 1, 2014

By M. F. Dunn

The objective of this work was to define jet fan performance in d variety of large cross-section underground mine applications and to develop guidelines for thin performance in open airways, dead headings, and multiple face areas. Measurements include common ventilation instruments, continuous recording remote electronic anemometers to measure air velocity, and sulfur hexaflouride tracer gas with chromatograph analysis to determine dilution rates and air recirculation. For open airways the following were determined: Large jet fans are leas efficient in smaller airways, but quite effective in larger open airways for achieving both uniformity end greater air entrainment, when inclined about 10° or elevated. For dead headings the following were determined: The jet fan must be placed against the rib of the heeding closest to the incoming airstream from the crosscut or recirculation will increase. The fan should be placed at the pillar corner to increase airflow. As the fan is moved closer inby, recirculation increases. Larger fans promote recirculation. Inclining fans about 12° improves airflow in large headings. For face areas the following were found: For panels having uncontrolled airflow, the fan should be placed in the incoming airflow, about one pillar inby, and directed diagonally across the faces. For panels having narrower rooms and controlled airflow, the fan should be placed alongside the panel side in the first room so as to direct or intersect the incoming airflow at the next entry or crosscut.

Jan 1, 1983

By W. Pietsch

For a number of reasons, solids entering and leaving facilities for the treatment of minerals are becoming increasingly finer. Such materials pose problems throughout processing. Solids featuring small particle sizes tend to dusting, result in losses and segregation, exhibit various storage, transportation, and metering problems, and fine particulate effluents can not be easily captured, used and/or recycled. Sustainable mineral processing must minimize the exploitation of natural resources and avoid the need for disposal of wastes. The first requires the use of lower quality raw materials and upgrading, which typically results in the production of fine grained concentrates, and the latter encourages the recycling of wastes and byproducts or efforts to investigate them as sources for secondary raw materials or other beneficial applications. To overcome the difficulties associated with fine particulate solids, size enlargement by agglomeration is necessary. The resulting products have free flow characteristics, do no longer dust or segregate, and are sized and shaped as required for optimum processing. In addition, agglomerated materials may be engineered to feature desirable structure, composition, and a number of related, improved properties. Such engineering may be applied for the modification of fine run-of-mine and up-graded minerals as well as the production of secondary raw materials from by-products or wastes. By the interdisciplinary application of size enlargement by agglomeration waste-free processing of minerals becomes feasible.

Jan 1, 2004

By M. J. Senk, A. Lusin

Federal regulations require that methane liberated at the face be diluted and removed to maintain methane gas concentrations below 1 pct (CFR) in working places and intake air courses. The delivery and distribution of intake air at the face is critical for effective face ventilation. Improved techniques for monitoring the movement of intake air to the face are needed. A test system was developed and a computer program written for using a three-axis ultrasonic anemometer to measure airflow in a simulated mine entry. Results of tests conducted in the entry showed that the anemometer is a valuable tool for measuring mine airflow conditions near the face.