Search Documents

By Pei-Yung Huang, C. R. Hayward

In order to understand more fully the actual state of copper lost in copper reverberatory slags, a systematic study on the various reactions between certain metallurgically important copper compounds and synthetic copper reverberatory slags was undertaken by the authors in the Massachusetts Institute of Technology from 1942 to 1945.1 This paper, being only a part of the work completed, is published first because it furnishes the first experimental evidence of the formation of copper ferrite from reactions between cuprous oxide and copper reverberatory slags. Choice of Slag Composition The choice of the composition of the synthetic reverberatory slags to be used was much deliberated. Commercial copper reverberatory slags, neglecting minor constituents, avcrage :2,3 45 to 47 pct FeO; 38 to 42 pct SiO2; 5 to 6 pct CaO; 5 to 6 pct A12O3. Since the ternary system CaO-FeO-SiO2 has been much more thoroughly studied4 and is much simpler than the quaternary system CaO-FeO-SiO2-Al2O3, it was decided to use calcium oxide only instead of calcium oxide and alumina in the synthesis of the slags. Fortunately the composition of the average copper reverberatory slag with calcium oxide substituted for alumina lies in the region of the phase diagram clarified by the investigators. A survey of the phase diagram (Fig I) suggested two compositions: (I) the composition near the invariant point S, which is made up of 46 pct ferrous oxide, 37 pct silica and 17 pct calcium oxide; (2) the composition near the invariant point K with 45.5 pct ferrous oxide, 43 pct silica and 11.5 pct calcium oxide. Composition S has the advantage that the percentages of ferrous oxide and of silica almost exactly coincide with those of the average reverberatory slags, and that of the lowest melting point (1093º ± 3ºC) in the whole ternary system. The calcium oxide content, however, obviously is high. Since we have already substituted calcium oxide for alumina, and since calcium oxide is more basic than alumina, the fulfil- slag is decidedly too basic. Composition K has a slightly higher melting point (1150O + 3OC) and a higher silica content, but this is preferred because the slag is saturated with respect to tri-dymite and thus should not corrode siliceous refractories. Besides, it is less basic than composition S. The filial slag composition, therefore, was chosen to

Jan 1, 1949

By J. H. Shillabeer

"Rational exploration requires the prior selection of areas possessing excellent geological potential and minimum hazards to commercial development . Within an over-all strategy of grass-roots exploration, two procedures for selecting areas for (i) coal and (ii) metals exploration are described. The procedures explicitly balance infrastructure requirements and environmental concerns for areas of geological merit not alienated in parks and reserves. Through consensus, priorities are attached to those areas meriting closer scrutiny and field reconnaissance.IntroductionMining companies need to know that having made a potentially economic discovery, they will be allowed to develop it with minimum delay and at reasonable cost. The environment for exploration in British Columbia is complex and recent experience suggests that conditions are not becoming any easier. Conflicts over land use issues, preservation and economic development are common. The high cost of exploration requires that the risks should be offset where possible by: (i) carefully selecting the areas in which to work (ii) conducting operations in a responsible manner, and (iii) working cooperatively with the community of interests. This paper concerns the first action: prior selection of areas.To aid exploration planning at Suncor, a procedure was developed to grade those areas of the province possessing favourable geology according to the ease with which a mine might be developed . This had to be done within the constraints of the company's over-all approach to exploration. This emphasizes ""grass-roots"" exploration of self-generated projects in British Columbia. In addition, having selected a favourable belt of rocks, it is intended to persevere there while steadily adding to the accumulated data base and local experience. Hence, it is intended to concentrate on an area. This implies a long-term commitment to an area which in turn increases the importance of the original selection.Suncor's search is directed to finding base and precious metals in intrusive and volcanic environments, and export quality coal."

Jan 1, 1985

By Leiv Kolbeinsen, Stian Seim, In-ho Jung

"The current work presents new experimental data in the iron-unsaturated region of the FeTiO3-Ti2O3-TiO2 slag system. The samples are prepared by melting pure reactants in a high frequency induction furnace that employs a cold crucible. A similar experimental set-up has been described in literature and proven suitable to investigate high titania slags. The FeO content of the samples range from 3.7 to 21.8 wt% and the Ti2O3 content range from 3.6 to 30.1 wt%. The liquidus temperatures of the samples are measured in-situ by a spectropyrometer and range from 1450 to 1645 °C.In addition, an improved thermodynamic database for the FeO-Ti2O3-TiO2 system has been developed. Ternary parameters have been included and optimized to fit previously published experimental data. This optimization minimizes the discrepancy between experimental data and thermodynamic calculations as previously discussed in literature. New liquidus projection plots are proposed for the FeO-Ti2O3-TiO2 and the FeTiO3-Ti2O3-TiO2 systems.IntroductionIlmenite (FeTiOs) smelting is a relatively small industry world-wide. However, a reasonable focus on the process has been applied in Norway due to the location of one such smelter in Tyssedal, which is located in the western part of Norway. The process is essentially carbothermal reduction, where most of the iron in the ilmenite is reduced to its metallic state, and the titanium oxide is concentrated in the slag product. The metallic iron is sold as a high purity pig iron and finds applications in cast products. The slag concentrate is further processed for the production of TiOvpigment and/or titanium metal. This further processing can be performed through different routes according to the purity of the slag concentrate."

Jan 1, 2012

By R. Hoffmann

THE Waelz process produces oxides of volatilizable metals from ores, metalliferous products and residues. The process was originally used for recovering zinc and lead, where tailings and residues containing those metals had accumulated at mines or smelters, but it is applicable for obtaining tin, arsenic or other volatilizable metals. It is useful when other methods of obtaining the metals from the ores or residues are too difficult or expensive or show too low a recovery. FIG. 1.-DAILY CAPACITY OF WAELZ PLANTS RUNNING OR BEING ERECTED. The Waelz process was developed in 1923 for the treatment of large calamine dumps in Upper-Silesia, which showed zinc contents of 8 to 10 per cent. and lead contents up to 3 per cent. The rapid development of the process, from the first trials up to the plants now working or in course of erection, is shown in Fig. 1. -The first industrial Waelz plant was started in 1925. Within two years the capacity of the working plants reached 700 tons material per day of 24 hr. During the year 1928 the daily capacity of the plants now at work or in course of erection will rise

Jan 1, 1928

By Albert E. Reed

The development of the modern highspeed vibrating screen, together with the increasing availability of long-lasting stainless-steel screen cloth for relatively fine-mesh separations, means that more screen circuits will be used in the future. It seems pertinent therefore to examine a few characteristics of screen-circuit products, and especially the points of difference as compared with products of classifier circuits. The most noticeable change that takes place when substituting screening for classification in a grinding circuit is a substantial drop in the circulating load, owing to the greater ease with which the "fines" leave the circuit. Where circulating loads of 500 to 600 per cent are considered fairly normal in classifier grinding circuits, the grinding circuit equipped with screens for equivalent work will have a circulating load of only 20 to 75 per cent. As a result, the products of screen circuits will show a minimum of overgrinding or sliming as compared with a classifier circuit. The desirability of this characteristic will naturally vary according to the metallurgical requirement in each case. Because screen separations make a sharper division according to particle size, the products of screen circuits can be expected to show greater crowding of particles near the point of separation. These changes in product characteristics are so important that other factors, both in the grinding and concentration processes must be adjusted if the operator is to take full advantage of the increased tonnages and higher efficiencies available to him through the use of the screen circuit. One factor that too often is overlooked when changing to screen circuits is the importance of adjusting the ball-mill or rod-mill charge, to compensate for: (I) increased tonnage of new feed, (2) decreased circulating load, or (3) more granular character of feed. These same factors should also be taken into consideration for their effect on the various types of concentration or flotation equipment that may follow the screen circuit. Over a period of years, this equipment has generally been designed and adjusted to the product of the classifier, therefore it seems obvious that some research on the adjustment and adaptation of concentrating and flotation equipment to screen-circuit products will be most profitable to the operators. To illustrate the points mentioned above, the results from three recent installations follow, with data on the comparative characteristics of screen and classifier circuits. A range of separation from 10 to 48 mesh has been chosen, using two general types of screening equipment and two types of classifiers. The first of the installations of which the results are to be examined is that of an iron-ore installation where eastern magnetite was being concentrated prior to sintering. Fig. I shows the original grinding circuit, using classification, while Fig. 2 shows the same circuit equipped with a

Jan 1, 1947

THE subcommittee on Coal Mining, since its appointment, has been engaged in collecting data about subsidences in coal mines in this country, and it now feels that almost all of the available data about occurrences of this sort in bituminous mines has been collected. As most of the bituminous seams are nearly level, the records obtained give the problem in its simplest form, without complications due to the pitch of the seam. Similar data is being compiled for the anthracite regions and it is hoped that this will be ready for the 1927 meeting. Copies of the questionnaire, Appendix A, were mailed to all of the coal operators' associations, to most of the large operating companies and to many engineers, with the request that any data on the subject be returned to the committee, or that advice of any subsidences known be given. The replies to most of the questionnaires were general only, although some specific cases were given. Many of the companies were unable to reply to all questions, as they lacked the necessary data, but in nearly every case where accurate data was available, it was cheerfully furnished, and any additional information requested was secured. All specific cases of subsidence were followed up by correspondence, and in several cases by personal inspection. Figs. 1 to 31 were made from the information furnished. Table 1 gives measurements of elevations taken in one case at intervals from October, 1913, to May, 1918. With one exception, where the evidence cannot yet be released on account of a lawsuit, it is believed that the cases submitted with this report include practically all that have happened in bituminous coal mining in this country of which actual measurements were secured. Some of these have already been published in the excellent report by Young and Stoek,1 and some instances have been secured from other publications. In collecting these data, the subcommittee had the Engineering Societies Library extend the bibliography given in the bulletin mentioned above to date. This list is given in Appendix B.

Jan 2, 1926

By P. L. Placek

Correlations were made on experimental data for four New Mexico ore series to determine relationships between ore grade and uranium extraction during leaching operations. Such relationships provide information needed to predict the long-range supply of minerals to meet national economic and strategic needs. Results show that other ore constituents and gangue materials in addition to uranium grade influence uranium extraction. In general, tailing grades decrease and uranium extraction increases as both H2S04 and NaCl03 concentrations increase. Terminal emf and terminal pH also were studied. Similar trends appeared for all ores; however, specific combinations of results also were observed for individual ores and ore series. Experimental results indicate that uranium extractions are higher for lower uranium feed grades than predicted by other estimates. Three factors--uranium feed grade, H2SO4 concentration, and NaC103 concentration--were used to design factorial experiments for each ore series. Four additional feed assay factors--V205, Fe, C02, and CaO--were included in regression equations to account for some of the variation in data. The three factorial factors are represented in the regression equations by linear and exponential terms of the form D i'1*G i + Di,2 *e Di, 3*Gi. The four additional assay factors are represented by linear and squared terms of the form Di,*Gi + Di,2*eDi3*Gi. where the Di, ,J are coefficients, the Gi are factors, and the symbol * represents multiplication in computer notation. The interactions of the factors are represented by products of the nonlinear terms for all pairs of the factors.

Jan 1, 1981

By L. W. McKeehan, W. C. Elmore

THE magnetic powder method, long used for roughly mapping magnetic fields, has recently been refined 1,2 for investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter' first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators3 have used Bitter's original technique, with slight modifications, to study the variation of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement in the powder technique which led us to the discovery of a new effect throwing considerable light on the magnetic secondary structure of alpha iron4 and of nickel' single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure. SPECIMENS The following list describes the specimens used in the present investigation. DESIGNATION DESCRIPTION A1 Silicon ferrite furnished to us by Dr. W. E. Ruder, of the General Electric Co., for which he gave the following typical analysis: C, 0.05; P, 0.038; 5, 0.026; Mn, 0.15; Si, 3.24. Disk, 0.60 cm. diameter, about 0.05 cm. thick.

Jan 1, 1935

By T. J. Driscoll

In this Bureau of Mines investigation, the electrochemical polarization behavior of Fe and Fe-1BCr has been characterized in rigorously controlled 1[N] H2S04 solutions stirred with oxygen or an inert gas. Samples that under-went various levels of corrosion or passivation were examined using Auger electron spectroscopy (AES) and ion sputtering. Passivation of iron occurred at a potential of approximately 0.6 volt (1) in poorly stirred, oxygen-saturated solutions for forward polarization (scanning from cathodic to anodic potentials); (2) in pH-adjusted (increased), well-stirred, oxygen-saturated solutions for forward polarization; and (3) in well~ and poorly stirred, oxygen-and helium-saturated solutions for reverse polarization. Passivation of Fe-18Cr occurred at a potential of approximately -0.1 volt in helium-, nitrogen-, and oxygen-saturated solutions for all cases of forward polarization and most cases of reverse polarization. Elemental depth profiles obtained from AES sputtering measurements indicated that films or adsorbed species were present on iron samples in solution subjected to open-circuit, active, and transpassive corrosion, cathodic reduction, and passivation. This conclusion was reached by considering the distribution of the solution species, primarily sulfur, in the films, which were composed primarily of iron and oxygen. Sulfur was present throughout the films on actively corroding samples, in the outer regions of films of passive and transpassive samples, and on the film surfaces of open-circuit and cathodically reduced samples. For Fe-18Cr, sulfur was found on the surfaces of films on passive samples only, indicating that only the passive samples had films on their surfaces in solution. The films on electropolished and passive Fe-1BCr samples had the largest chromium concentrations, estimated to be approximately 45 at. pct, with less chromium in films of cathodically reduced, active, and open-circuit samples, in that order.

Jan 1, 1979

By A. C. Fieldner

It is estimated that 6,202,235,000 gallons .of- gasoline was produced during the year 1922. The crude light oil- output Burin- the same year is estimated at 111,000,000 gallons, or 1.8 per cent of the gasoline production. In fact, if all the coal mined were coked in by-product ovens, and the light oil recovered therefrom, this product would amount to only 15 to 20 per cent of the quantity of the petroleum gasoline now produced annually. It is obvious therefore, from these figures that the light oils by present coking processes can not assume great importance as a gasoline substitute in a national sense. However, the use of light oil as a motor fuel is of real importance in districts adjacent to by-product coking operations from which a reasonable proportion of the local motor fuel supply may be derived. The certainty of diminution of petroleum resources in the relatively near future demands the utmost utilization of gasoline substitutes from the distillation of coal as well as other sources. Motor benzol is a by-product from the destructive distillation of coal. From 11/2 to 3 gallons of refined motor benzol is obtained per ton of coal carbonized. The light oil vapors are extracted from the by-product coke-oven gas by passing it upward through a series of towers in which these vapors are absorbed in a descending current of "wash" oil (petroleum distillate). The light, oil is recovered from this wash oil by distillation with live steam, the resulting crude light oil consisting of a mixture of benzol, toluol, xylol, solvent naphtha, and a small amount of other substances (unsaturated hydro-carbons, carbon disulphide, and other sulphur compounds, phenols and pyridines) is then transferred to an intermittent still and fractionated into crude motor benzol, which includes the toluol and a part of the xylol or light solvent naphtha. The crude, motor benzol is yellow in color, contains sulphur compounds which corrode copper and brass, and also contains unsaturated bodies which oxidize and polymerize on standing, producing sediment and forming gummy deposits highly objectionable when the benzol is used in motors. These objectionable

Jan 1, 1923

By L. W. Holm, A. K. Csaszar

A series of laboratory experiments was conducted in which oil was displaced from a porous medium by water-driven slugs of alcohols or similar solvents. The solvents used were soluble to some degree in both oil and water and covered the range of solubilities from complete solubility in oil to complete solubility in water. Displacement experiments were conducted on 2-and 3%-in. in diameter consolidated cores and 1-and 2-in. in diameter unconsolidated sand packs. The cores and sand packs ranged in length from 1 to 30 ft, and they were saturated with brine and crude or refined oils. The solvents used included ethyl alcohol, isopropyl alcohol (IPA), tertiary butyl alcohol (TBAI, secondary butyl alcohol (SBA), n-amyl alcohol (NAA), methyl ethyl ketone, acetone and others. It was found that all of the oil present in a porous medium could be miscibly displaced by injecting a slug of mutual solvent and driving it with water. The oil-recovery efficiency was dependent upon (1) the relative solubilities of the solvent in oil and water, and (2) the distance traversed by the flood. For complete oil recovery from cores, a smaller amount of a preferentially oil-soluble solvent was required, compared to the amount of preferentially water-soluble solvent needed. The size of the solvent slug required varied inversely with the linear flooding-path length raised to the 0.65 power. Water-driven dual solvent combinations (an oil-soluble solvent slug followed by a water-soluble solvent slug) were found to effect complete oil recovery with less total solvent than any single solvent used. In these dual-solvent displacement experiments, the slug size required varied inversely with length raised to the 0.55 power. Based upon the experimental results, a theory was developed to describe the displacement of oil and water by mutual solvents, and equations are presented to predict the production history in a linear system. These equations take into account the properties of the solvents and the porous medium. INTRODUCTION Oil-recovery processes which utilize displacing fluids that are miscible with the reservoir fluids have been studied extensively in recent years. Because of the poor contact efficiency and high pressure requirements of the LPG-gas displacement process there has been considerable interest in the alcohol-water process, and a number of studies have been made on the recovery of oil through the use of solvents which are mutually soluble in oil and water. An investigation by Sievert, Dew and Conleyl indicated that the use of mutual solvents would be limited because the presence of water in a porous medium would cause a phase break in the leading edge of the displacing solvent. Their study also showed that, in consolidated cores containing. only oil, the displacement of oil by a water-driven mutual-solvent slug of tertiary butyl alcohol (TBA) was affected by the viscosity ratios of the fluids involved. Gatlin and slobod3 concluded that an isopropyl alcohol (IPA) slug acts as a miscible piston, completely displacing both oil and water until the alcohol content of the mixing zone falls below the concentration necessary to maintain miscibility. Their study was conducted on uniform unconsolidated sand packs. They concluded further that IPA could be used effectively to recover oil from a watered-out sand. In a paper by Taber, Gamath and Reed4 relating an investigation on sandstone cores, it was stated that the displacement of oil by mutual solvents, particularly IPA, was not a miscible displacement and that no improvement in efficiency could be expected with increase in flooding-path length. However, their analytical analysis of the displacement mechanism using TBA is, in fact, one which indicates that the displacement is controlled by miscible mixing. They suggested that the lack of improvement in efficiency with flooding - path

By Liang Yinhuai

The hydraulic-stowing mining method is most effective for mining thick coal seams. It is superior to the sliced cover-caving and artificial mining method and the fully mechanized sublevel-caving mining method for the following reasons - a much higher recovery rate is achieved, there is much less surface subsidence and roof pressure, there is no hidden danger of gob fire, and much less methane emission and coal dust problems, etc.. However, its superiority is overshadowed by its backward stowing technique which makes mechanisation of mining and stowing difficult, causes bleed water interference to production and to the environment and is uneconomic because of the high cost of stowing material. These disadvantages limited its application to coal seams that are difficult and not suitable to be mined by other mining methods. The remedy is in reforming it thoroughly to permit mining of otherwise unminable seams and this paper presents the reformation.

Jan 1, 1992

By Lorne Roberts

"This paper describes: how Falconbridge's fire protection system meets the needs of the Lockerby Mine; why the system was chosen over other alternatives; how it is unique, but can be applied to any underground situation; details of the system; how it was installed; the role of a fire protection company; and general considerations when choosing afire-suppresant system.IntroductionIn May 1981, after about three years of searching for the best fire protection system for the re-opened Lockerby nickel mine at Whitefish, near Sudbury, Ontario, Falconbridge Nickel Mines Ltd. installed an AFFF type of fire suppression system. It was designed and supplied by the Fire Protection Systems Division of Levitt -Safety Ltd.The system protects against loss of life, equipment and/or production, and it complies with legislation should fire occur in a fuel storage area and/or scooptram garage and service bay at any or all of the three levels near Shaft No.2.About 18 months after Levitt-Safety began working with Falconbridge, the system was designed and installed at a cost considerably less than that which would be incurred if fire damage caused the loss of two days of production.The fire protection system, which overcomes a limited water supply, is a self-contained balanced pressure proportioning system. It senses the flow and automatically determines the correct concentration of foam to water. It is triggered by a release mechanism which operates a bank of nitrogen cylinders, which in turn pressurize a pressure vessel to expel the foam concentrate and water from the tanks. This solution is piped to sprinkler heads in the specific area."

Jan 1, 1982

By Charles C. Fatino, Joel S. Hirschhorn

Loose compacts of strained and annealed stainless-steel powders were sintered at various temperatures and times to determine the effect of residual strains on the sintering behavior. The atomized powders were prepared by annealing, ball milling, and rean-nealing. The residual strains and domain size were determined by a Fourier analysis of X-ray diffvaction dala. The specimens were prepared by siwzultaneously sintering cylinders of both strained and unstrained powder. The evaluation of the sintered compacts included density measurements, metallographic examinations, and analyses of X- ray diffraction data. The results of these studies reveal a definite increase in sintered density and sintering rate for the strained powders. THE pressure compacting of metal powders causes deformation of the particles, mechanical interlocking, and increased contact area. After the deformation, severe residual strains remain in these particles. The subsequent contributions of these strains to the sintering process have been considered to be negligible, since the recovery and recrystallization temperatures usually occur prior to the temperature required for the sintering process. Sintering is con-sidered to be the process by which the powders are transformed into solid compacts at temperatures below their melting points. The sintering operation for stainless steel usually takes place in the range of 2050" to 2400°F (0.84 to 0.95 T,, where T, is the absolute melting point or liquidus temperature) while the temperature required for recovery is approximately 1800°F (0.75 T,). However, it has been shown for several metal powders that densification becomes significant in the range of 0.35 to 0.45 T,.' It is the purpose of this study to determine what effect residual strains have upon the sintering behavior of stainless-steel compacts. Loose compacts were selected for study in order to isolate the strain contributions and eliminate the variables inherent in sintering of pressure-formed compacts. Additional variables were minimized by using only one mesh size, one composition, one particle shape, and also by simultaneously sintering both types of powder. Very little work has been carried out previous to the present study to delineate the effect of strains on sintering behavior. Lenel et 01.2 observed that residual stresses in copper compacts caused shrinkage at comparatively low temperatures. Delisle3 loose-sintered ball-milled electrolytic iron and observed that bonding among particles began at a lower temperature as compared to the behavior of annealed powder. Increased densification of ball-milled oxide powders has also been noted.4'5 EXPERIMENTAL PROCEDURES Powder Preparation. The powder used for this study was a commercial-type 316L stainless steel made by the atomization process. A typical chemical analysis is: C- 0.025 pct Mo- 2.2 pct Cr-18.6 pct Ni-12.5 pct Fe—Balance The atomizing process is essentially the rapid freezing of liquid droplets. This nonequilibrium cooling causes coring to occur and two distinct phases are present within the solid particle, the austenitic phase and the ferritic phase. Due to the presence of this ferritic phase, the particles tended to fracture as well as become cold-worked during the subsequent ball-milling operation. (It was also found that this type of cooling produced a broadened and shifted

Jan 1, 1968

By R. D. Pehlke, J. V. Gluck

A study was made of the effect of small additions of metallic solutes on the thermodynamic activity of zinc in dilute solution with molten bismuth in the range 450o to 650°C. The experimental measurements were made in a multielectrode galvanic cell using. a fused LiCl-KCl electrolyte. The activity of zinc in binary solution exhibited a strong positive deviation from Raoult's law and obeyed Henry 's law to at least 0.050 mole fraction. The ternary addition of lead, gallium, or indium increased the activity of zinc. Cadmium or tin additions slightly decreased the zinc activity. Copper, mercury, silver, or antimony caused moderate decreases, while gold strongly decreased the zinc activity. The results are expressed in terms of Wagner's interaction parameter ejZn and a second-order cross-interaction parameter. The interactions for copper, gold, silver, and antimony showed a linear dependence with reciprocal absolute temperature, while the other interactions were essentially independent of temperature over the experimental range. Since tin and antimony decreased the zinc activity, the hypothesis of a purely periodic variation with atomic number was rejected. A semiquantitative explanation was possible with a free-electron model when relative electronegativities were used to express changes in the electron/atom ratio caused by the solute addition. Random solution and quasi-chemical models correctly predicted the majority of the interactions for which binary data were available to apply them. A knowledge of the thermodynamic interactions in liquid (and solid) metallic solutions is of considerable theoretical and experimental interest in the formulation of quantitative thermodynamic relations for metallurgical processes. The approaches to defining the interactions may be either phenomenological (i.e., "What mathematical function adequately describes observed behavior and permits extrapolation to new situations?") or theoretical, such as a specific model

Jan 1, 1968

By Russell W. Dayton

THE metallurgical polarization microscope has been utilized in several researches in the last few years, thus attaining a fair degree of prominence, but little has been written in a manner suitable to a metallurgist concerning the theory of this instrument. In this investigation the theory was carefully studied, and the results are presented here in a detailed manner, yet as simply as possible. The theory - is discussed with particular reference to the three chief functions of the instrument: (1) determination of anisotropy; (2) effect of strain; and (3) identification of inclusions. Each of these is investigated experimentally, with especial attention to the mechanism of producing any effect. Where possible, the discussion is supplemented by photomicrographs. The instrument used had numerous defects as a polarization microscope; these and their remedies are discussed. In the microscopic study of transparent mineral sections (chalcography) the use of polarized light has aided tremendously in the identification of a mineral. The determination of strain in transparent substances (photoelasticity) by the use of polarized light has lately become a commercial process, used in testing finished glass articles. The success of the use of polarized light with opaque materials has not been so great. The magnitude of the effects obtained is much less than that of the corresponding effects with transparent materials, and the mechanical difficulties are much greater. Königsberger, (1)‡ in 1909, was the first to apply polarized light to the microscopic study of

Jan 1, 1935

By Rudolph G. Wuerker

Charles T. Holland (Head, Dept. of Mining Engineeri*, Virginia Polytechnical Inst., Blacksburg, Va.) Mr. Wuerker has presented a very interesting discussion of the use of triaxial test methods for investigating the strength properties of rocks. Such methods, no doubt, eventually will develop considerable information of interest to those concerned with the design of mine layouts, particularly in the field of pillar design. From his discussion of my recent article, "Cause and Occurrence of Coal Mine Bumps" (Holland Mining Engineering 1958, p. 933-1002), it is evident that in one place at least I did not make my meaning clear to him and perhaps others. To clear the matter up I think it best to quote from the article, somewhat more fully than did Mr. Wuerker, as follows: "4) In actual operations — because rocksare not perfectly elastic, homogeneous, nor isotropic and because local yield does occur — the maximum stress as demonstrated by Phillips (Ref. 22, pp. 64, 65) and indicated by much experience in mining, does not occur at the walls of the opening but at a short distance inside the pillar. Furthermore, the maximum stress does not reach as great a value as theoretical considerations and laboratory experimental methods indicate.* Actual distance inside the pillar, measured from the wall, at which the maximum stress exists, has not been determined. Observations in many mines, however, indicate that this distance could have a mini-value of one to six or eight times the bed thickness and that it is probably affected by width and height of the opening, depth of cover, and relative values of the elasticity and plasticity of materials comprising the roof, floor, and coal seam. The actual value of the stress produced probably lies between the theoretical maximum and the average stress concentration that would be produced if the weight of the strata above the unsupported opening were evenly distributed over the pillars for a distance equal to the opening width." The footnote reference in the above quotation referred to the following: "*For example, the Pocahontas No. 4 coal bed in southern West Virginia is mined under cover up to 1800 ft thick. Development openings are driven 18 to 20 ft wide, and the bed is about 6 ft thick. According to the work of Panek, the tangential wall stress at mid-bed height under these conditions would reach values between 4000 and 5000 psi. Actual tests of 3-in. cubes of this coal show its compressive strength would be much less than this, perhaps as low as 400 psi. Yet the pillars usually show no evidence of failure in these headings. In this same bed at a depth of 800 ft, the author has seen an opening 225 ft between supports lying between two old groves approximately 1100 ft apart. According to the theoretical considerations, the stress in the pillar walls would have been about 18,000 psi, yet the pillar showed little or no evidence of weight. In view of these observations, it is clear that the wall stress does not attain the maximum values indicated by theory." (Underlining added to original wording.) By referring to Fig. 2A of my paper it will be noted that theoretically the maximum pillar stress would occur at the pillar wall, i.e., at the passageway surface of the pillar. Obviously this cannot be correct in the cases of stress ranging from 4000 to 18000 psi since the coal at the surface of the pillar is under no constraint and cannot have a strength much greater than 400 or 500 psi. Hence, my conclusion that the maximum stress does not occur at the wall but back in the pillar some distance from the wall. Since these stresses are pushed back in the pillar from the wall, it is also obvious that the loads transferred to the pillar from the opening will be spread over a greater area and hence Pillar stresses will not rise to the values postulated by theory and photoelastic experiment. Further since to visual inspection the coal along the pillar wall did not appear to be failed the conclusion was reached that the stress shift was caused by local elastic or plastic yield and by difference in the elastic modulus of the rocks composing the mine floor, mine roof, and coal bed. Later on under the heading "Strength of Mine Pillars" (pages 1000-1002) the effects of constraint is briefly described. Also a formula taking into account constraint is developed relating pillar strength to the uniaxial strength of coal and the L/T ratio of the pillar. Since my paper was written, reports of experiments conducted in South Africa (Denkhaus, et. al., 1959), in Sweden (Hast 19581, and in Canada (McInnes, et.al., 1959) reveal that the conclusion expressed relative to the existence of a low stress area existing around the edges of pillars and solid faces as described above is generally correct. But it seems possible that where the wall stress developed is less than the unconfined strength of the rock composing the pillar and where the roof, floor, and pillar

Jan 1, 1961

By Oscar Marzke

STUDIES on the precipitation of a face-centered from a body-centered structure-a common occurrence in alloy systems-are essential to the development of a theory for the formation of segregate structures. The separation of the alpha phase from the beta of the copper-zinc system is an example of this type of precipitation. EARLIER STUDIES ON THE SUBJECT R. F. Mehl and 0. T. Marzke1 in 1931 presented a paper giving the results of some investigations carried out by them on the segregate structures produced when the alpha and gamma phases of the copper-zinc system and the alpha phase of the copper-aluminum system precipi-tate from the beta phases of these systems. They showed that the alpha phase precipitates as needles close to the [111] directions of the beta phase. In the discussion of that paper some doubt was expressed about the nature of the segregate. More investigations were undertaken to determine the character of the precipitate in the copper-zinc system and also the orientation relationship between the matrix and precipitate. The present paper gives the results of these investigations. Since the publication of the earlier paper, several other papers on this subject have been published in this country and abroad. Haneman and Schroder2 reported that the alpha phase precipitates as needles along the [111] directions of the beta phase and that these needles align themselves to form plates on the {111} planes of the matrix. Mathewson and Smith3 pointed out that the {111} plane does not contain the [111] direction and that it would be quite impossible, therefore, for needles in the [111] direction to form plates on the {111} plane. They suggested

Jan 1, 1933

By Todd Nottingham

Channel deepening of major ports is challenging designers to explore innovative solutions to ensure stability of bulkheads, such as for the Oakland Inner Harbor. This particular challenge was met with the use of the SPIN FIN® Tension Pile for restraint of an HZ combination wall along the Oakland Inner Harbor Shoreline in Oakland, California. A SPIN FIN pile is a pipe pile with welded plates at the pile tip that increase pile capacity. A brief history of the project will be provided as well as results of pile load tension tests, pile strain gauge, and wall deflection under construction loads. Tension pile load deflection results will be discussed with recommendations toward establishing deflection-based ultimate load criteria. A discussion of predicted wall loads and field observed wall loads will be provided.

Jan 1, 2008

By E. Yalçin, A. Ünal

In transitional mineralization, the sill of the underlying variogram is relatively easily estimated, but the estimation of the nugget effect may be more difficult. This study aims to determine for massive copper deposits just how sensitive the estimations of ore reserve, economic copper content, total net value, and ultimate pit limits are to the errors of estimation in the nugget effect of the spherical variogram model. A massive copper deposit which has a log-normal distribution and a spherical variogram was simulated on a rectangular grid using the turning bands method. By using the three dimensional random kriging method, the mean block grades were estimated at four different sampling densities. The ultimate pit-limits were determined by using the two-dimensional dynamic programming algorithm. To calculate the estimation errors, the values obtained by using the actual nugget effect and structured component values were deducted from the estimations obtained using the incorrect nugget effect and structured component values. For isotropic massive copper deposits, it was found that the ratio of the nugget effect to the structured component of the spherical variogram has no significant effect on either the block grades estimated by the kriging method or on the ultimate pit limits.

Jan 1, 1992