Search Documents

By Steven Hoerger

Mixed integer linear programming (MILP) production scheduling models can be used to evaluate if tonnage improvement projects will deliver value over all time periods and whether new bottlenecks will be created. These MILP models can evaluate the interconnected effects of mine and process capacities, mining locations, cutoff grades, stockpiles, and orebody grade/tonnage distributions. A case study compares potential value creation from a mine capacity increase, a mill capacity increase, or a simultaneous increase in all capacities. For perspective, project valuations for capacity increases are compared against valuations for cost reduction projects, mine planning improvements such as phase design, dynamic cutoff grades and stockpiling, and the impact of geostatistics improvements in the areas of block model accuracy and ore control selectivity.

Feb 1, 2024

By William J. Shampine

This map shows general trends of the chloride concentration of water in the upper part of the Floridan aquifer. Below this part of the aquifer, high chloride water can be found everywhere in the State. The accompanying cross section shows the depth to salty water across central Florida. In the center of Florida, fresh water may be found as deep as 2.000 feet, whereas, along the coast it may extend no deeper than about 200 feet. Chloride concentration in small local areas may deviate from the values represented on both the cross section and the main map. This map shows general trends of the chloride concentration of water in the upper part of the Floridan aquifer. Below this part of the aquifer, high chloride water can be found everywhere in the State. The accompanying cross section shows the depth to salty water across central Florida. In the center of Florida, fresh water may be found as deep as 2.000 feet, whereas, along the coast it may extend no deeper than about 200 feet. Chloride concentration in small local areas may deviate from the values represented on both the cross section and the main map.

Jan 1, 1966

By A. Wallace Mitchell

Barite deposits in Nevada occur as bedded and vein-types along a north-northeastern -trending zone which parallels the Antler orogenic belt The bedded deposits of Nevada are the most significant economically. They are presently supplying eighty-five percent of the domestic barite production which is used primarily as a weighting agent in the petroleum drilling industry. The ore bodies are controlled both structurally and stratigraphically, occurring along regional and local structural breaks in siliceous eugeosynclinal rocks of mid-Paleozoic age. Evidence for origin of the barite includes sedimentary and hydrothermal features indicating that localization probably took place along fractures in the seafloor.

Jan 1, 1980

By L. W. McKeehan

THE occurrence of twins in large ferrite crystals, made by a new process, was reported in a recent note.1 This paper describes a typical case of such twinning and suggests, on the basis of the observed facts, why smooth slip-planes are rarely observed in this metal. METHOD OF PREPARATION The material in. which the crystals here dealt with were grown was made from 1/8-in. Armco iron welding rod containing C, 0.04; S, 0.037; P, 0.003; Si, 0.008, and Mn, 0.02 per cent. This rod was cold drawn into wire about 1 mm. dia. A piece of this wire was supported vertically and was locally heated in hydrogen at atmospheric pressure to about 1400° C. by an alternating current (60 cycles per sec.) of about 35 amp., passed through it between a pair of traveling contacts about 8 cm. apart. The rate of travel for the case in hand was 12 cm. per hr. After some 30 cm. of the length of the wire had been heated and cooled in this manner the whole wire was immersed for a few seconds in dilute nitric acid, not restrained by alcohol. Etching was continued until, ass nearly as could be judged by eye, the original smooth cylindrical surface of the wire was no longer capable of specular reflection. MEASUREMENTS The wire in the etched state was next mounted in a goniometer of special form which allowed the measurement of the spherical coordinates of the normals to any plane surfaces left by the etching. These coordinates were most conveniently a polar distance, ?, from one direction of the wire axis, and an azimuth or longitude, [ø], from an arbitrary prime meridian. The region to be described more particularly is shown at a low magnification in Fig. 1, which gives two different views, differently illuminated to show the spatial relationship of a crystal occupying most. of the part shown and of an inclusion, or rather a series of three inclusions suspected of being twins based on the principal crystal.

Jan 1, 1928

By Glen M. Bellew, James F. Mehnert

"The Kansas City District-United States Army Corps of Engineers has completed the design modification of a pile supported floodwall located along the Missouri River in Kansas City, Kansas. This deep foundation supported floodwall protects over 2 billion dollars in infrastructure, is approximately 17 ft (5.2 m) tall and is 1,446 ft (440.7 m) long. Design modifications included the addition of a row of drilled shafts and the addition of relief wells. Typically, deep foundation design is controlled by total stress analysis and undrained soil strength. Neither controlled design at this site, where effective stress and drained strength controlled. During high river stages, artesian pressures develop, leading to a reduction in both effective stress and pile capacity. Deep foundation analysis software available to the designer does not allow these effective stress conditions to be directly entered, so a unique way was developed to account for them. A load test was performed to verify the design. During load testing, the supporting ground was unsaturated and had effective stress conditions different from those that controlled the design. A load test evaluation process involving unsaturated soil mechanics was developed and performed. This paper will share both the effective stress design process used and the load test interpretation process performed.INTRODUCTIONThe Fairfax-BPU Floodwall is part of the Fairfax-Jersey Creek Flood Protection Unit in Kansas City, Kansas. The floodwall was built in the 1940s and currently provides Missouri River flood protection for over 2 billion dollars of infrastructure in the Fairfax Industrial Area. The floodwall averages 17 ft (5.2 m) in height, is 1,446 ft (440.7 m) in length and is divided into 35 separate monoliths. The originally constructed foundation support for each of these monoliths typically consisted of three rows of seven tapered steel monotube piles, each roughly 20 ft (6.1 m) in length. All monontube piles are tipped in sand, well above bedrock."

Jan 1, 2016

By B. M. Larsen

In endeavoring to put the art of the steelmaker on a more scientific basis, as a means of securing closer control of the product, we must be severely critical of the basis of any theory we use. In particular, we must be careful to distinguish between factors that are primary and those of only secondary impartance. The concentration relations that determine the slag-metal equilibria, which are usually more or less closely attained, are of course of primary significance, but a, dear picture of the whole process requires that the actual rates of the several reactions be taken properly into account. At the high temperature of the steelmaking furnace, all reactions might be thought to be very rapid, but some of them in fact are not; the essential causes of this condition are important to a proper understanding of the process. This paper aims to present, and to justify, the viewpoint that the most significant reaction is the oxidation of carhon in the metal, the progress of which determines the oxygen pressure levels in slag and metal and produces stirring effects, all of which influence the course of the process as a whole. Reaction Rates at Steelmaking Temperatures General experience in reaction rates makes it almost certain that at steelmaking temperatures equilibrium is attained practically instantaneously when the reactants are well distributed in a single liquid phase —that is, in the so-called homogeneous reactions. The actual slowness of some of the reactions in the open-hearth furnace must therefore be attributed to a relatively slow rate of diffusion within the slag or metal phase, which limits the rate at which the reactants can meet each other in the liquid steel or at its surface. That the reactions can be made to go with great rapidity, by proper mixing and stirring of the reacting phases, is indicated by the following illustrations: 1. In the Bessemer process there is intimate contact between air and the whole mass of metal, and the reactions are complete in a few minutes. 2. Perrinl has demonstrated that by pouring liquid steel into slag contained in a deep ladle, and thereby producing almost a slag-metal emulsion, the phosphorus or oxygen content of the steel is adjustcd immediately. 3. Barret, Holbrook and Wood2 observed a quite rapid rate of desulphurization when powdered calcium carbide was stirred vigorously into liquid iron. 4. When a spoonful of liquid steel is poured into a. mold containing aluminum wire, the formation and precipitation of alumina occurs in the fraction of a second required to freeze the surface layer of the tiny ingot. The first three examples all show that any means of increasing the effective surface between slag and metal and promoting intimate mixture of the reacting phases, thereby obviating the limitation imposed by diffusion, will enhance the speed of the steelmaking process.

Jan 1, 1941

By B. M. Larsen

In endeavoring to put the art of the steelmaker on a more scientific basis, as a means of securing closer control of the product, we must be severely critical of the basis of any theory we use. In particular, we must be careful to distinguish between factors that are primary and those of only secondary impartance. The concentration relations that determine the slag-metal equilibria, which are usually more or less closely attained, are of course of primary significance, but a, dear picture of the whole process requires that the actual rates of the several reactions be taken properly into account. At the high temperature of the steelmaking furnace, all reactions might be thought to be very rapid, but some of them in fact are not; the essential causes of this condition are important to a proper understanding of the process. This paper aims to present, and to justify, the viewpoint that the most significant reaction is the oxidation of carhon in the metal, the progress of which determines the oxygen pressure levels in slag and metal and produces stirring effects, all of which influence the course of the process as a whole. Reaction Rates at Steelmaking Temperatures General experience in reaction rates makes it almost certain that at steelmaking temperatures equilibrium is attained practically instantaneously when the reactants are well distributed in a single liquid phase —that is, in the so-called homogeneous reactions. The actual slowness of some of the reactions in the open-hearth furnace must therefore be attributed to a relatively slow rate of diffusion within the slag or metal phase, which limits the rate at which the reactants can meet each other in the liquid steel or at its surface. That the reactions can be made to go with great rapidity, by proper mixing and stirring of the reacting phases, is indicated by the following illustrations: 1. In the Bessemer process there is intimate contact between air and the whole mass of metal, and the reactions are complete in a few minutes. 2. Perrinl has demonstrated that by pouring liquid steel into slag contained in a deep ladle, and thereby producing almost a slag-metal emulsion, the phosphorus or oxygen content of the steel is adjustcd immediately. 3. Barret, Holbrook and Wood2 observed a quite rapid rate of desulphurization when powdered calcium carbide was stirred vigorously into liquid iron. 4. When a spoonful of liquid steel is poured into a. mold containing aluminum wire, the formation and precipitation of alumina occurs in the fraction of a second required to freeze the surface layer of the tiny ingot. The first three examples all show that any means of increasing the effective surface between slag and metal and promoting intimate mixture of the reacting phases, thereby obviating the limitation imposed by diffusion, will enhance the speed of the steelmaking process.

Jan 1, 1941

By Michael E. Zellars

The distribution of phosphate in Pliocene-Miocene deposits of the Southeastern United States was controlled by the prevailing geologic setting. For each basin a unique set of conditions in terms of relationship of land mass to shelf, depositional environment and seawater composition, and movement controlled phosphate distribution. Concentration sufficient to recognize the deposits as a resource occurred in lagoons or shallow neritic zones, with clastics and carbonates diluting the section basinward. Each deposit within a basin displays similar metallurgy and lithology, notwithstanding post-depositional alteration.

Jan 1, 1978

• One effect of the British devaluation of the Pound Sterling, with its resultant lowering of the pay limit, was the addition of considerable tonnages of previously marginal ore in gold mining. Crown Mines, Ltd., reported that 1,245,000 tons of such ore had been added to available reserves. But for devaluation, a steady decline in ore reserves had been a feature of operations during the previous ten years, and would have continued. •Loree Colliery of the Hudson Coal Co. is using a Humphrey spiral cleaning plant to meet requirements of the state in the matter of stream pollution. However, the process is producing a salable product. •Noranda is considering plans for constructing a commercial sized unit designed to produce elemental sulphuric acid and sintered iron oxide from pyrite. Test plant results have indicated the No. 5 ore zone can be treated by the new process economically. •A magnetic fluid clutch, and magnetic amplifiers for motor and generator control, have been developed under Navy contract by Vickers' Electric Division, in St. Louis, Mo. This constitutes the first commercial production of the clutch recently developed by the Bureau of Standards. •Fuel experts estimate coal production will run up to 500 million tons this year based on the expectation that business conditions will continue to be good. They also expect that in the future the use of coal will increase by 50 pct over today's level. These expectations are based on the fact that it provides the bulk of the heat, light, and power for making steel, for manufacturing, and for generating electricity as well as the development of the coal burning gas turbine and processes for making gas, gasoline, and oil from coal. •Entombed miners may benefit from a two-way communication system which utilizes the earth's strata as a network for electric signals. The use of FM radio waves makes this possible. The invention includes a portable transmitter-receiver unit kept near the face, and a more powerful portable equipment of the same sort above ground. In use, two probes on wires from the apparatus are driven into the earth. • The Union of South Africa has launched a uranium production project which government leaders think will help the West maintain world atomic supremacy. Experiments under way in the pilot plants are expected to lead to the establishment of a chain of processing factories along the Witwatersrand in which uranium will be reclaimed from gold tailing. •Recent developments in mechanized mining at the Bureau of Mines oil-shale mine near Rifle, Colo., have lowered mining costs to 29 cents per ton of shale. The cost of producing crude shale oil from 30-gal-per-ton-shale, using the new mining and processing techniques, would be about $1.50 per barrel. This is 500 lower than any previously stated price. • COMINCO is planning to open the old Bluebell lead-zinc mine near Nelson, B. C., on a 500-ton-per-day basis. The old workings will be pumped and a 970-ft incline sunk. A mill will be constructed at the property.

Jan 7, 1950

By F. T. Cawood

This article is a continuation of a series of publications by the authors on the international debate on resource nationalism, with specific reference to South Africa. Previous outcomes have shown that mine nationalization is not a solution for South Africa, and that maintaining stability of the current mineral and tax regimes is fundamental. It will not be wise to replace existing law and policy instruments until there is a better understanding of the distinction between fact and public perception about the impact of the current system. The new scheme of state custodianship linked to a mining royalty that effectively targets economic rents provides for effective resource use. The methodology in this article is to consider how South Africa's mineral tax regime can be tweaked to achieve optimal management and benefit from mineral extraction and associated rents by avoiding changes feared by investors. The major finding is that the current suite of instruments can be considered a suitable platform for optimal management of resource rents. However, it will be necessary to first investigate ways of improving the mineral beneficiation intent of the royalty structure, and secondly investigate whether the mineral rent portion of the royalty formula can be ring-fenced for the purpose of establishing a sovereign wealth fund.

Jan 1, 2013

By B. W. Christ, P. M. Giles

Mossbauer effect measurewents have been made on I-mil-thick foils of commercial 1 wt pct C steel and Fe-2 wt pct C alloy. The experimental method required about 3 to 5 vol pct of a phase in the nzultiphase steel sample for detection. Room-temperature Md'ssbauer patterns obtained on austenitized atid quenched samples exhibit fifteen, and possibly twenty-one, lines. A sharp parama&tetic singlet and a quadrupole doublet, poorly resolued from the singlet, are attributed to austenite. Remaining lines are due to tnartensite. Accurate evaluation of austenite line paranzeters is not feasible if significant amounts of other phases such as carbides or martensite occur simultaneously with austenite. This is demonstrated by comparison of hyperfine interactions determined for austenite in multiphase high-carbon samples with those reported for Fe-C austenite in a nearly 100 pct austenitic sanple. Lines from carbides are incompletely resolced from austenite lines, as demonstrated by comparison of austenite line positions with carbide line positions calculated frow published values of hyperfine interactions. One martensite line overlaps an austenite line in the pattern for commercial 1 wt pct C steel. Results of this study suggest that the usefulness of e M6ssbauer pectroscopy for quantitatizle analysis of austenite in bulk samples of quenched and tempered high-carbon steels is restricted by poor resolution. Use of Mossbauer spectroscopy for phase identification and for evaluation of atomic and electronic structures appears quite feasible, however, The Mijssbauer effect has been widely discssed,'-and e Mossbauer effect measurements have been reported on materials of metallurgical interest.7"20 In particular, it has been proposed that e Mossbauer patterns of commercial steels and laboratory-made Fe-C alloys, in the quenched condition, are composed of lines originating in two phases, Fe-C austenite and Fe-C martenite.-' Evidence accumulated in this study demonstrates that three absorption lines found in the central region of the e Mossbauer pattern obtained on quenched steels are attributable to retained austenite. This interpretation is supported by parallel decreases in the intensity of these three lines caused by subambient cooling of commercial 1 wt pct C steel samples after water quenching to room temperature. A second result of this study is to clarify effects of line resolution and sensitivity in the Mossbauer patterns of multiphase steels on the accu- rate determination of austenite line parameters. Experimental line widths (full width at half height) are generally 1.5 to 3 times larger than the natural line width of 0.19 mm per sec. At least two lines, and sometimes more, from a single phase such as cementite (Fe3C), other carbides, martensite, and austenite fall in the energy band, i0.85 mm per sec. hhis band width is employed simply for convenient reference. It represents approximately the energy interval between the + 112 to 112 transitions in ferrite and is expressed as the velocity needed to Doppler shift a 14.4kev 7 ray to the aforementioned ferrite energy levels. This energy band is referred to as "the central region of the Mossbauer atttern:: in this paper. Hence, due to the large number of lines from different phases in a multiphase steel falling in a relatively narrow energy band, absorption lines from the different phases may overlap. Analysis of available data, presented below, indicates that this occurs to a significant extent for phases which commonly occur in quenched and quenched and tempered high-carbon steels. One consequence of limited resolution in the Mdssbauer patterns from multiphase steels is difficulty in accurate determination of such line parameters as position, width, and intensity. In fact, it appears that quantitative analysis for retained austenite in quenched and tempered high-carbon steels is not practical with the present experimental method. Line resolution is influenced to some extent by sensitivity. We point out below that atom or volume fractions of less than about 3 to 5 pct are not detected by the present experimental method. Thus, the presence of a multiplicity of phases does not always lead to impaired resolution. Finally, we report in this paper room-temperature MGssbauer parameters determined for austenite in a freshly quenched, commercial 1 wt pct C steel and in a freshly quenched laboratory heat of an Fe-2 wt pct C alloy. These parameters are compared with others reported in the literature. Three types of hyperfine interactions are detectable in a Mossbauer effect measurement: isomer shift, quadrupole interaction, and magnetic dipole interaction. These interactions are evidenced by one, two, and six line patterns, respectively.'-4 More than one type of interaction has been reported in certain metallurgical phases thus far studied by this method. Isomer shift is the experimentally measured displacement of line position from some arbitrarily defined reference position. In the case of a multiline pattern, isomer shift is given by the displacement of the centroid (center of gravity) of that pattern from the reference position. All isomer shifts measured at finite temperatures contain a second-order Doppler effect characteristic of that temperature. The isomer shift is related to the total s electron density at the nucleus, becoming more negative with increasing s electron density. The first-order quadrupole effect arises from the interaction between the nuclear quadrupole moment and any axially symmetric electric field gradient in

Jan 1, 1969

By R. Fedors, T. Ghezzehei, D. Or

The phenomena of dripping into cavities (e.g. tunnels and drifts) within an unsaturated fractured porous medium under ventilated conditions is studied to improve estimates of dripping rates, drop sizes, and chemical composition of droplets that could affect the integrity of high-level nuclear waste packages placed in drifts. The sensitivity of dripping rates and water chemistry to ventilation is analyzed at various flow rates using analytical expressions linking flow on fracture surfaces to drop formation and evaporation. The model was tested using laboratory experiments involving machined aluminum slabs designed to represent a simplified morphology of a fracture face intersecting a cavity and using natural fracture surfaces from a welded tuff. Comparison with ten years of data on dripping in natural caves showed good agreement with model predictions. In particular, for low dripping rates, evaporation due to ventilation leads to larger drop sizes and alters drop chemistry by increasing the concentration of solutes in the drop relative to that in the water flowing on the fracture face.

Jan 1, 2000

By C Standing, R Lacourt Rodrigues, C Q

The value of iron ore depends on the grade of the contaminants. Scheduled iron, and the associated contaminants, provides mine planners with a measure of stockpile feed and blending requirements. Blending at the stockpiles is one approach to optimising iron grade, while minimising the variability of contaminant grades. These schedules are typically based on resource models incorporating geology and iron and contaminant grades. Resource models reflect best estimates of trends for each of the elements rather than the potential variability, which is critical for accurate short-term blending. Conditional simulation provides a tool to describe the likely variability of each element. Only recently has conditional simulation technology allowed the inherent correlation between elements to be incorporated into the process. This paper presents the stepwise co-simulation process used to simulate and describe multi-element variability for effective mine planning. A case study using the multi-element conditional simulation and the subsequent uncertainty in the schedule and stockpile planning is presented. This process supports proactive mine planning to minimise unexpected fluctuations in the final product.

Jan 1, 2005

By F. Hassan, M. A. Arafa

At El-Gedida iron ore deposits there is a block of about 30million tons neglected due to its higher sulfur content due to the presence of barite gangue minerals. From this bluk by magnetic separation dual concentrates of high grade iron concentrate (~65%Fe and total Sulfur of 0.26%) and the second concentrate is barite of (60.87% BaO and total impurities of less than 3%).

Jan 1, 1999

The Silvermines area of north County Tipperary in Ireland has experienced mining activity for over a thousand years, with lead, zinc, copper, barite and sulphur being extracted from a series of Carboniferous limestones. The last mine to operate in the area was closed in 1993. A legacy of contamination and derelict surface structures remain. Following the death of cattle in the vicinity in 1999, a governmental Inter-Agency Group was established to conduct an investigation. The ?Silvermines Rehabilitation Project? resulted, and included a proposal for the development of a Mine Waste Management Facility (MWMF) to act as a repository for waste materials from problematic sites across the area. The nature of the setting supported an effective solution from both a cost and performance perspective; and with limited maintenance requirements. Locating the MWMF where most wastes were identified would help minimise handling and relocation of materials. This position coincided with an area of artesian groundwater pressures. The resulting MWMF design consisted of a perimeter engineered embankment with the crest elevation designed to just exceed the groundwater piezometric surface. The base would remain unlined and groundwater permitted to rise up into and saturate the contained in-situ tailings deposits and imported mine wastes. The proposed system thus benefited from the ?wet cover? approach to minimising further oxidation of wastes and metal leaching, but without the usual accompanying outward hydraulic gradient and leachate management issues. A sub cap drainage layer with downstream outlet was incorporated to prevent any possibility of hydraulic rupture following an unexpected rise in groundwater heads. Leakage rates from the MWMF were deemed to essentially be driven by surface infiltration rates alone (characteristic of a ?dry cover? approach), with the proposed composite capping system simulated to perform at an infiltration rate of less than 1 mm per year. A toe drain was incorporated with the perimeter containment system, and this collection together with diverted neighbouring drainage was directed under gravity to a dedicated Passive Treatment System (PTS). Overall, effluent water quality from the PTS has been predicted to reflect an annual mass metals removal in the order of 95% below baseline.

Aug 1, 2013

By Frank W. Bowdish

During the early 1960's, a method was developed for refining sand from the Arkansas River to produce a feldspathic product that was proposed for use in making colorless glass. Because of the need for chemical uniformity, a cooperating glass manufacturer specified certain ranges of percentages for each chemical constituent of the sand. These specifications were met by fulfilling the single requirement that alumina vary by no more than 20.1 percent from the specified value. This translated to a total variation of only about 1 percent in the feldspar content of the mixed quartz-feldspar products. Because the feldspar was lighter than the quartz, the average density of refined sand varied depending on composition. Densities, determined to five significant figures, of several samples were correlated with their chemical analyses, and the correlation could then be used with density determinations to more reliably indicate compositions than by chemical analyses only. The effects of several variables on the composition of refined sands were studied. There was a regular variation in the proportion of feldspar with screen size. A series of samples with their natural size distributions were more nearly uniform in composition than the same sands after screening and recombination. The screening and recombination process was done so that the sands had identical size distributions. Variations in the refining showed little effect on composition. A pile of flow-back sand from a construction sand washer was found to be severely segregated. However, samples taken from many points in the river near the sand plant and from the flow-back discharge pipe over several weeks very nearly met the uniformity specification. If care was taken to avoid segregation either before or during processing, it should be possible to meet the uniformity specifications for a feldspathic glass sand.

Jan 1, 1978

By M. Surracco, M. C. Tilocca

"Mineral comminution is often a costly process which also requires high level of energy. In the course of the studies carried out by the researchers of the Department of Civil-Environmental Engineering and Architecture at the University of Cagliari, aiming at the optimization of the reduction processes, it has been experimented, among of others, the effects of high-speed water jets on minerals grinding. As far as coal is concerned, some of the solutions initially adopted are presented in this paper, which essentially relied on the water jet power only, with secondary use of mechanical actions, to reach the most modern solutions that envisage the use of mechanical energy, normally used in traditional grinding machines, in synergy with hydraulic energy transferred by water jet.INTRODUCTION Mineral comminution can be rather expensive and demand a high-energy consumption, especially for fine sizes (Austin, 1979). Further interesting perspectives in this area may be offered by comminution means aided by high pressure water jets (Ciccu 2007), whose crushing potential is currently used for several operations such as cutting different materials, rock digging and industrial cleaning. The crushing action of water jets may induce a traction stress in materials where substances of a mineral nature, especially if characterised by permeable porosity, oppose a minor resistance (Griffith, 1920). The first solutions to this purpose essentially relied on the sole energy of water jets, with a secondary use of mechanical actions (Ciccu, 1993). Results were encouraging, despite the high values of specific energy for the low capacity of treatment. However, due to the difficulty in making the techniques mainly based on hydraulic energy practically applicable to solids comminution a solution was experimented, with some interesting results, consisting in the combination of mechanical energy, normally used in traditional grinding devices, with hydraulic energy transferred through water jets, in a synergic relationship (Ciccu, 1998; Tilocca, 2016)."

Jan 1, 2018

By W. D. Ludemann, E. A. Loria, E. A. Rowe

The isothermal recrystallization of electrorefined vanadium has been studied as a function of annealing time , temperature , and prior deformation . Specimens were cold- rolled from 30- to 75 - percent reduction in thickness , then annealed from 700 ° to 1,200 ° C at time periods ranging from 1 minute to 96 hours . The course of recrystallization was followed by means of hardness , metallographic , and X- ray techniques , and a recrystallization diagram was constructed . Interpretation of the data indicated that there was around 50- percent softening due to recovery ( first stage of softening) before recrystallization began . The defining of recrystallization limits with respect to the amount of deformation was precisely established for electrorefined vanadium . More than 30- percent reduction was necessary for recrystallization to occur at 850 ° C. With 60- percent reduction , it was initiated at 750 ° C and completed at 950° C. The activation energy for recrystallization , as derived from the data , was 95,300 cal per mole for 60 - percent reduction and annealing at 750 ° to 900 ° C. Recrystallization by the mechanism of nucleation and growth was the principal process during the second stage of softening . minor part of the second stage of softening took place as strain- induced boundary migration , which was observed in specimens reduced 30 percent , bent in L- shape , and annealed at 950 ° C. Grain size decreased significantly only with the largest reductions and annealing between 750 ° and 950 ° C. Grain growth was expressed by the empirical relation D = KKtt"" ,, the exponent being the same at 60- percent reduction and annealing from 750 ° to 900 ° C. Accordingly , the activation energy for grain growth was 75,000 cal per mole .

Jan 1, 1964

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson

"The United States (U.S.) Department of Homeland Security (DHS) Directorate of Science and Technology (S&T), utilizes a probabilistic risk assessment (PRA) approach to explore the risks (anduncertainty) from chemical, biological, radiological and nuclear (CBRN) threat agents to the Homeland.This end-to-end risk methodology considers a broad range of hazards incorporating emergingtechnologies, available countermeasures and input from the Intelligence and Law Enforcementcommunities (IC/LE) to evaluate the acute risk to human health due to an attack on the U.S. homeland. The PRA generated output provides a mechanism to examine risk mitigation strategies, critical vulnerabilities, critical data and knowledge gaps and relative risk rankings of materials, targets, classes of compounds and scenarios."

Jan 1, 2017

By Lee R. Kump, Sarma V. Pisupati, Peter L. Rozelle, Alan R. Larson, Timothy S. White, Nicholas A. Crescenzo, Maureen D. Feineman

The Mercer Clay bed in central Pennsylvania has produced feedstocks for the refractory industry in the USA and has also been investigated as a source of alumina and lithium. Developments in global markets for these commodities, as well as rare earth elements, have led to their classification as critical minerals in the USA, in turn renewing production opportunities for the Mercer Clay resource. The work reported here includes a review of the clay types and minerals involved, as well as past mineral processing and extractive metallurgy test work, and reports new research results from renewed investigation of the deposit as a polymetallic resource. This renewed work has found lithium contents that exceed 1,000 ppm, lying directly below the overlying Mercer coal, where the alumina content ranged from 32 to 34 wt%. Total rare earth concentrations were somewhat lower than have been found elsewhere in the region, and the highest contents were also found to be stratigraphically close to the coal. Further work is required to establish the mineral hosts for lithium and rare earths and to define the extent of enriched alumina, lithium, and rare earth concentrations.

Jul 22, 2021