Search Documents

By T. Vincze

Effective coal mine face ventilation, for remotely controlled and automated mining systems, is essential for the control of methane. The evolution of new mining equipment and methods has required changes and improvements in face ventilation methods. One emphasis today is on the use of remotely operated and automated mining systems that can be used to make continuous cuts of 6 m (20 ft) and deeper. U.S. Bureau of Mines research is studying ways to more effectively ventilate these extended cuts. Two face ventilation techniques that utilize either blowing brattice or a jet fan for deep cutting are examined in this paper. Bureau of Mines procedures for evaluating face ventilation systems are also discussed.

Jan 1, 1992

By W. Petruk

Imaging is a fundamental requirement when characterizing minerals, ores and related products. Images are used for presentation, texture analysis, characterization, image analysis, identification, etc. The image mode that is utilized is dependent on the application, mineral properties and available instruments. Different instruments produce images that display different features. In order of increasing complexity they are: hand specimens, a non-polarizing microscope, polarizing optical microscope, scanning electron microscope (SEM), low vacuum SEM, microprobe, secondary ion mass spectrometer, staining, cathodoluminescence, tomography and others. Image analysis uses images produced with either an optical microscope or a SEM, but the SEM images are superior in this application. Key words: Mineralogy, Imaging, Mineral characteristics, Scanning electron microscopy, Optical microscopy, Cathodoluminescence

Jan 1, 2003

By H. C. Theuerer

EVEN the highest purity silicon available for semiconductor use contains significant amounts of donors and acceptors, usually aluminum, phosphorus, and boron. Aluminum and phosphorus can be removed from silicon by adaptations of the zone refining techniques' widely used with germanium. Removal of boron, however, has been a difficult problem. The approximate distribution coefficient for boron in silicon is 0.8, so that while zone refining is possible, it is not very effective in any reasonable number of passes. It has been found, however, that boron can be effectively removed from silicon by treatment of a liquid zone with hydrogen and water vapor. Starting with 40 ohm-cm, n-type silicon, use of zone refining coupled with hydrogen

Jan 1, 1957

By Herryal Z. Anwar

In recent years, many both mining and civil engineering projects are developed in the area which may be categorized unstable, such as fractured and jointed rocks or "water sensitive rocks". For example, in underground coal mining, in which the floor strata normally consist of weak shale, the problem that may arise in roadway is floor heaving. In this case cement injection in borehole appears to be an economically effective method in order to make roadway more stable. This method may be also applied in the projects in which the constructions are laid on fractured and jointed rock. Nevertheless, the successful cement injection is much dependent on the water-cement ratio and the injection technique. This paper discusses the application of cement grouting to improve the ground stability in longwall mining, the laboratory experimentation of cement grouting and the method of floor injection.

Jan 1, 2000

By Fredrik Søreide

Several potential marine mineral deposits of various types have been identified within the Norwegian EEZ. The Norwegian University of Science and Technology has recently designed and built a new remotely operated vehicle (ROV) system for scientific investigations of the deep-ocean and seafloor. A program to locate and investigate the most interesting of the identified marine mineral deposits using the new ROV system is underway. The ROV has been designed for detailed survey and sampling tasks. Although initially built for a major marine archaeology project, the design is equally suited to locate and investigate marine mineral deposits. The ROV is equipped with a high precision multi-sensory package that consists of various high quality cameras and lighting systems (together with state-of-the-art video and photo mosaic systems), several sonar systems, magnetometer and various other sensors. The ROV is also equipped with a 7-function manipulator arm and an excavation system. Internal collection baskets are used to store material for retrieval to the surface. A closed-loop control dynamic positioning system is used for detailed positioning of the ROV. Position data and other information are stored in a digital data management system. The ROV will also be used together with a specially developed remotely operated tool (ROT). The size and shape of this benthic lander can be adjusted before it is carefully lowered to the seafloor. The ROV can be docked on a moving platform on the ROT, to do detailed scientific investigations. The ROT can also be equipped with a separate sensor and system package, including drilling, excavation and coring units. This paper will present the new remotely operated system and the planned projects in Norway.

Jan 1, 2004

By Charles M. Cooley

DURING the last week in April, cards were sent out from New York to Institute members affiliated with the Mining, Geology, and Geophysics Div. The cards requested recipients to indicate their main technical interest, within the division, i.e., mining, or geology, or geophysics. The reason for the cards is simple. Within the Institute more than 8000 have expressed either primary or secondary interest in this division. However, there is no way to determine the technical association stimulating this interest.

Jan 6, 1953

By B Bonfils, P Lois Morales, C Evans

One of the main challenges for current and future mining and processing methodologies is to understand the characteristics of the rock so that its behaviour in one or more parts of the mining process chain can be predicted. Features such as rock texture, mineralogy or border complexity between minerals control how the rock behaves from the processing plant through to the final products, including tailings disposal and thus can affect the feasibility of the project from technical, economic and environmental impact perspectives. Understanding how the mineralogy and texture of rock affect its behaviour in mineral processing is a demanding area of research and is essential knowledge in predicting the processability of complex ores in different stages. This study aims to demonstrate that different types of relevant information can be extracted from a range of currently available analytical methods. However, this information can be used in a complementary way for building a more comprehensive rock characterisation at the microscale and better-predicting ore processing characteristics from the intact rock through to tailing disposal. CITATION: Lois Morales, P, Evans, C and Bonfils, B, 2018. Multisource rock characterisation at microscale for a better understanding of processing characteristics, in Proceedings Complex Orebodies Conference 2018, pp 44–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Frederic Dewey

BONE-ASH cupels have been used from time immemorial to absorb litharge, and accompanying oxides; in assaying. Doubtless, also, from the earliest days cupels have been most unjustly blamed for much poor assaying. It has long been known that the precious metals go with the litharge into the cupel. This occasions a loss of precious metals and reduces the results of the assay. There have been many investigations of cupels and the most diverse views have been expressed, the extremes being the statements of Lodge 1 that every cupel has some effect upon the loss in assaying telluride ores and of the Campredons2 that coarse and fine and hard and soft cupels all give the same loss of silver when cupelling the same weights. The truth lies between these statements and much nearer the latter. In a vast majority of cases the influence of the cupel is not dominant and is outweighed by other conditions, particularly the temperature of the cupelling bead. At the Spokane meeting of the Institute I presented a paper on the Assay and Valuation of Gold Bullion,3 which recorded the results of many hundreds of assays made in the Mint service under everyday commercial conditions, which of necessity differ from scientific conditions. In following this matter up, for the purpose of increasing the accuracy of our commercial methods of bullion assays, the question of the absorption of gold by the cupel was found to be a most important one and was taken up for investigation. In a lesser degree, the silver absorption is important and interesting, but at present it appears to be far more complicated and, while many figures showing silver absorption may be found through this paper, much further investigation is required to put the subject upon a satisfactory basis.

Jan 11, 1917

By F. P. Dewey

Bone-ash cupels have been used from time immemorial to absorb litharge, and accompanying oxides, in assaying. Doubtless, also, from the earliest days cupels have been most unjustly blamed for much poor assaying. It has long been known that the precious metals go with the litharge into the cupel. This occasions a loss of precious metals and reduces the results of the assay. There have been many investigations of cupels and the most diverse views have been expressed, the extremes being the statements of Lodge1 that every cupel has some effect upon the loss in assaying telluride ores and of the Campredons2 that coarse and fine and hard and soft cupels all give the same loss of silver when cupelling the same weights. The truth lies between these statements and much nearer the latter. In a vast majority of cases the influence of the cupel is not dominant and is outweighed by other conditions, particularly the temperature of the cupelling bead. At the Spokane meeting of the Institute I presented a paper on the Assay and Valuation of Gold Bullion,3 which recorded the results of many hundreds of assays made in the Mint service under everyday commercial conditions, which of necessity differ from scientific conditions. In following this matter up, for the purpose of increasing the accuracy of our commercial methods of bullion assays, the question of the absorption of gold by the cupel was found to be a most important one and was taken up for investigation. In a lesser degree, the silver absorption is important and interesting, but at resent it appears to be far more complicated and, while many figures showing silver absorption may be found through this paper, much further investigation is required to put the subject upon a satisfactory basis.

Jan 1, 1918

By H. A. Wheeler

That lead and zinc deposits are the result of prolonged,, slow deposition is the idea of most students of ore deposits, and in many cases, where the ore-bearing solutions have been very weak or the precipitating conditions have been very feeble, the ore accumulations have undoubtedly taken a long period of time. As these two vital conditions have been subject to great variations in the different mining camps, the following example is highly interesting in showing that deposition can be very rapid under favorable conditions, geologically speaking, and also extremely recent. In fact, the writer is inclined to regard most, if not all, of the Mississippi Valley deposits of lead and zinc as probably being very young, at least not older than Tertiary, if not Quarternary, in age. The extensive Joplin lead and zinc district, in southwestern Missouri, which is about 60 years old and has numerous mines that were abandoned from 1 to 50 years ago, shows that the lead and zinc today are in an active condition of solution and redeposition, although these two metals occur in the predominant form of sulfides. The mine waters from the older and more or less abandoned portions of the district are frequently so acid, mainly from the oxidation of associated pyrite, as to necessitate the use of wooden pipes and pumps. The first boom in the Oklahoma zinc fields, which is the southwestern extension of the Joplin district, occurred when ore was accidentally struck in drilling a water well. Among the mines then opened up was the Mission mine, at Lincolnville, Ottawa County, Okla. This mine was opened in 1903 in lean "sheet ground," or a flat blanket formation of chert carrying disseminated zinc blende, or "jack," and galena. Theore-body was very free from iron pyrites and the concentrates were very high grade, the "mineral," or lead concentrates, assayed 80 to 85 per cent. lead and the jack, or sphalerite, assayed 60 to 65 per cent. zinc. The orebody was very shallow, occurring at a depth of 76 to 95 ft. (22 to 28 m.) and very wet, requiring three or four pumps to handle the water. The mine was operated until 1914, when it was closed by litigation and immediately filled with water. The second Oklahoma boom, five years ago, opened up the large, active camps of Picher, Tar River, and Century, which are located 2 to 5 mi. west of Lincolnville. They are considerably deeper, being farther down on the westwardly dipping monocline that emanates from the Ozark

Jan 1, 1920

By Alper Kirmaci, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Injuries and fatalities resulting from roof falls are still a major concern in U.S. coal mines, and many researchers are focused on developing meaningful approaches to minimize this hazard. In the United States, coal mine roofs can vary widely in composition, geometry, and inherent heterogeneity, leading to a wide array of different roof fall failure types. Researchers frequently employ numerical modeling tools to reproduce this physical phenomenon and provide key guides to engineers regarding roof conditions and control as long as the input data and constitutive relations are appropriately selected. Simulating such complexity requires expertise and constitutive models that adequately simulate roof behaviors. However, the currently available constitutive models have shortcomings in capturing some of the roof fall failure types common in underground coal mines, such as guttering. A new constitutive model is developed to address the shortcomings of constitutive models commonly used for coal roof stability analysis. The constitutive model developed in this study combines the anisotropic-elasticity and nonlinear strain-softening responses. In addition, the developed constitutive model can simulate up to three different joint sets implicitly, allowing for use in both continuum and discontinuum settings, and can be used in both Lagrangian finite-volume and distinct element method codes of Itasca. First, the mathematical expressions of the model are provided. Afterward, the validation phase of the developed model that covers comparisons with analytical solutions and those of existing models (e.g., anisotropic elasticity, ubiquitous-joint, and bilinear strain-hardening/softening ubiquitous-joint plasticity) is presented. Finally, a hypothetical coal mine roadway facing high horizontal stress is simulated. The presented model successfully shows three distinct stages of a cutter roof in a shale roof: (1) initiation of shear cracks at the rib– roof intersection, (2) extension of cracks deeper into the roof (i.e., above the roof bolt length horizon), and (3) cantilevered roof. It is demonstrated that the presented constitutive model has the potential to help future researchers in simulating various roof responses.

Jul 1, 2023

By Hans Hamrin, Bruce Kennedy

Once an ore body has been probed and outlined, and sufficient information has been collected to warrant further analysis, the important process of selecting the most appropriate method or methods for mining can begin. At this stage, the selection is preliminary only, serving as the basis for a project layout and feasibility study. Later, it may be found necessary to revise the details, but the basic principles for the ore extraction should remain a part of the final layout. With respect to the basic principles employed, relatively few mining methods are used today. For the purposes of this presentation, the principles are classified as follows: 1) For naturally supported stopes, the available methods are room-and-pillar mining and sublevel stoping. 2) For artificially supported stopes, the available methods are shrinkage stoping, cut-and-fill mining, square-set mining, and longwall mining. 3) For caving methods, the available techniques are sublevel caving and block caving. Due to the uniqueness of each ore deposit, the variations on each of these methods are nearly limitless. It is impossible to include even the major variations in this chapter; the goal of this chapter is to present the principles as a guide to the mining engineer in adapting the general methods to specific needs. The selection process described herein is intended to supply the techniques by which the candidate methods available for a given ore body can be reduced to one or two feasible approaches. The feasible approaches then can be evaluated in detail, and the particular modifications can be investigated. In describing costs and economic factors, all values herein are expressed in terms of 1978 US dollars.

Jan 1, 1982

By Daniel B. Conn, John L. Floyd

PhotoSeis™ is a blast analysis method that combines the advanced technologies of high speed motion picture photography and digital seismology. When fracturing rock with the use of explosive energy, the human eye cannot detect the details of the process due to its short duration. An extended time base is required to accurately quantify the response of the rock mass to the detonation process. This time base is provided by the use of high speed motion picture cameras. The control of ground vibrations and airblast is an important consideration when developing efficient blast designs. High vibration and airblast levels can be an indication of improper design, inaccurate detonators, or adverse geology. Since many factors can elevate airblast and ground vibration, a greater understanding of the site specific response to the blast design is needed that is beyond the scope of simple seismographic recordings. By synchronizing the photographic record provided by the high speed motion picture cameras with the airblast and vibration information from digital seismological monitoring, the Photoseis™ technique can be of great assistance in controlling airblast and vibration and optimizing the use of explosive energy for rock fragmentation.

Jan 1, 1990

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

8.1 INTRODUCTION Under room and pillar mining if the extraction ratio is low, (i.e., < 50%) a pillar can support the overburden without collapse and there will be no surface subsidence whatsoever. In other words, if the pillar sizes are properly determined to support the overburden weight, the roof strata cannot cave and there will be no surface subsidence, provided the entry width is small and properly reinforced so that a continuous roof fall leading to piping or the total collapse of the roof does not occur. Under the prevailing mining conditions in the US if only development mining is em¬ployed in room and pillar mining (i.e., no pillar extraction), the extraction ratio is usually less than 50% and generally no surface subsidence will occur. If pillar mining is employed, surface subsidence may occur, depending on the extraction ratio and the size of the remnant pillars (or stumps) left in the gob. The higher the extraction ratio, the smaller the stump pillars left behind in the gob. As the size of the stump pillars becomes smaller, the possibility of their support¬ing the roof without collapse is smaller. If all stumps are crushed completely, the roof will collapse and surface subsidence will occur. Again, whether surface subsidence occurs, it depends on whether the remaining stumps can support the overburden or not. Therefore, since the weight of the overburden which the stump pillars have to support is proportional to the mining depth, a fixed¬size stump pillar can support the overburden at a shallow depth, but will collapse under greater depths. In this context extraction ratio is not the only parameter for determining whether surface subsidence will occur. Furthermore, during pillar mining a pillar can be cut away in many ways to finally reach the same extraction ratio. Therefore, the safest way to determine whether or not sur¬face subsidence will occur in room and pillar mining is to compare the strength of all stump pillars in the panel of interest with the weight of the overburden that the pillars have to support. If they are too small to support the overburden, surface subsidence will occur. Under normal mining practices the characteristics of surface subsidence profiles vary with methods of mining. In the US there are two types of coal mining methods, i.e., longwall and room and pillar mining. Longwall mining is indisputably a total extraction method, but different percentages of coal recovery are achieved in room and pillar mining. Recovery is much higher for sections with pillar extraction than those without pillar extraction. For those without pillar extraction, coal recovery increases with increasing entry width or decreasing pillar size. For those with pillar extrac¬tion, the total coal recovery depends on the amount of coal ex¬tracted from each pillar which is in turn dependent on the roof conditions and methods of pillar extraction. Bauer and Hunt (1981) analyzed the characteristics of the subsidence profiles due to the three types of mining methods in Illinois. Fig. 8.1 shows the range of locations associated with the following profile features: profile edge, maximum tensile curvature, maximum slope, maxi¬mum compressive curvature, and maximum subsidence. The scat¬ter of the data increases with decreasing percentages of extraction. The profile is much sharper for longwall mining and becomes milder as percentage of extraction decreases; for longwall mining the profile edge is always beyond the opening, while in room and pillar mining it may fall within. The location of maximum tensile strain moves outward, while that of the maximum compressive strain moves inward as the percentage of extraction decreases and the maximum subsidence decreases with decreasing extraction ra¬tio. The general concepts discussed in this chapter may not apply to the entry development sections between two longwall panels where roof caving in both panels are very severe and overlap each other. Consequently, it must be treated differently. 8.2 CASE STUDIES Kohli et al. (1982) described several case studies on surface subsidence due to room and pillar mining with pillar extraction. In one case, the seam was 6 ft thick and ranged from 650 to 800 ft deep. The panel was 720 ft wide (Fig. 8.2) and was developed with seven entries. Each entry was 18 ft wide and the pillars were driven at 88 ft center-to-center between entries and crosscuts. Dur¬ing retreating, two additional pillars (pillars J and K) were devel¬oped, two blocks ahead of the pillar line, to take the barrier pillar, 160 ft wide, between panel No. I and No. 2. Pillar extraction began by taking a central slice across the whole panel, beginning from pillar 0 through J. After that, each pillar was sliced by 6 wing-slices, 3 on each side, leaving 4 stumps, 2 on each side. One of each pair was triangular shaped approximately 6 ft wide by 26 ft long. The other was trapezoidal, 26 ft long by 16 ft and 10 ft wide at the upper and lower bases, respectively. This resulted in a total extraction ratio of 85% within the panel. Obviously the stump pillars were not large enough to support the overburden and col¬lapsed completely. The final subsidence profiles were rather smooth, just like those under total extraction (Fig. 8.3). The max¬imum subsidence on Lines A and B was about 3 ft for an average mining height of 6 ft, but the locations of the maximum subsidence were skewed toward panel No. 1. Along Line D, the central por¬tion was flat-bottomed, but the maximum subsidence was only 2 ft, mainly because Line D was only two blocks from the right-side edge. Notice in every profile there was heaving of as much as 0.3 ft, beyond the edges above the solid coal. In another case (Fig. 8.4), the seam was 6 ft thick under 650 to 850 ft cover. Three panels, 710, 400, and 350 ft wide, respec¬tively, were extracted side by side. The entries were 18 ft wide and the pillars at 88 ft center-to-center between entries and crosscuts. Pillar extraction was practiced the same way as described previ¬ously. According to the mine maps, there was no barrier pillar left between the adjacent panels. Thus after extraction the three panels formed a common gob of more than 1460 ft wide. This was re¬flected in the development of the subsidence profile along the county road. After Panel No. I was mined, the maximum subsi¬dence of 1.2 ft occurred at Monument No. 1. This was increased to 1.6 ft after the extraction of Panel No. 2 and went to a further 1.8 ft after the extraction of Panel No. 3. The final maximum subsidence of 4.3 ft occurred at Monuments No. 6 through No. 8, while the remaining portion of the county road showed rebound. However it must be noted that the subsidence profiles were rather bumpy and fluctuated, perhaps an indication of the irregular stump pillars that were left and crushed at various time after mining. Moebs (1982) surveyed the subsidence profiles of four room

Jan 1, 1992

By Jian Wang, Hongyang Cao, Binxiu Wu, Junhong Li, Jimin Wang

"The enrichment and separation of scattered metal indium component in the pressure leaching solution with sulfuric acid from vacuum furnace germanium slag were studied by iron substitute and P204 extraction, which is supplied by shaoguan smelter. The experimental results show that the extracting power of P204 for indium from pressure leach solution is powerful. The optimal technological condition were the ratio of P204 and sulphonating serosene 3:7, phase ratio 1:3, solution pH 1.2, and extracting 5 minute. The enrichment indium solution of 21.7 g/L In at 95.2% recovery ratio was obtained by three-stage counter flow extraction and four- stage counter flow stripping.IntroductionScattered metals, such as Indium and germanium, were inriched as intermediate product or by-product during the metallurgy process of other non-ferrous metals, such as lead, zinc, copper and tin. For example, the indium and germanium were inriched in vacuum furnace germanium slag, which is the by-product of zinc vacuum distillation operation from hard zinc. It is difficult to recovery the indium from the vacuum furnace germanium slag, because the indium content is low, and the chemical composition and phase compositon were complex.Recovery indium from bearing indium zinc slag was researched extensively, such as pressure acid leaching, high temperature evaporation, solvent extraction method[l-7], acid leaching method has the advantages of high leaching rate, which can be separated hydrochloric acid, sulfuric acid and silicon fluoride acid systems. Solvent extraction method has the advantages of low production cost, fast reaction speed, high enrichment ratio, and simple operation."

Jan 1, 2013

By W. J. Whiten, D. W. Grinsberg

Most cluster analysis techniques are not well suited to the analysis of engineering data as they have been designed for more qualitative data that tend to produce compact clusters. A clustering technique is described which develops and uses local cluster shapes to build clusters that are suitable for use in engineering applications. The technique is finding application in the analysis of many types of data, particularly where multiple trends and outlying points occur in multiple dimensions. Applications of particular interest are the calibration of on-stream analytical equipment and the analysis of data on plant performance. In both cases the multidimensional nature of the data renders manual analysis very difficult

Dec 1, 1991

By Victor G. Hills

This paper comprises suggestions on certain points rather than a complete survey of the whole subject. In other words, it is a contribution to the kenera1 discussion invited by John Hays Hammond in his paper, presented as a Presidential address at the Chattanooga meeting of the Institute, in October, 1908.1 Mr. Hammond says, in conclusion: "... I am not offering a code, or even an official and representative declaration of principles.. My remarks are intended, and will, I hope, be accepted, simply as a contribution to that discussion of their theme in which every engineer of experience may participate." Such a discussion has been conducted in technical journals, as well as in contributions to the Transuctions of the Institute; and, in the remarks here offered, I shall have occasion to refer the read& to what I have thus published elsewhere, for more extended statements of my views. What Mr. Hammond says about loyalty to employers, the double capacity of the engineer as an employer, the expert witness, commissions on machinery, the statement that most swindling is done by laymen and not by engineers, duty to the investing public, and the engagement of local engineers as colleagues, it is a pleasure to indorse. Under the head of the expert witness, Mr. Hammond refers to the address of Dr. R. W. Raymond on Professional Ethice. This paper con-

Jan 1, 1911

By Arcy R., D&apos George

The Bureau of Mines has developed, on a laboratory scale, a superior Eluex-type circuit for eluting and recovering uranium from ion exchange resins. The improved circuit differs from conventional Eluex practice in that a stage of uranium solvent extraction is coupled with each stage of resin elution rather than the elution and solvent extraction operations being conducted separately. The new system reduces the number of stages, retention time, and resin inventory in the elution circuit to one-fourth or one-fifth that in existing circuits. The system is applicable to both resin-in-pulp and moving-bed-type ion exchange uranium recovery circuits.

Jan 1, 1969

By D. W. Fuerstenau

A detailed study of the residence time distribution in an industrial balling circuit is presented. Using fired recycle pellets as a tracer impulse in each experiment, material was found to pass through the drum under plug flow conditions with a mean residence time of about 20 seconds. The time for a single pass through the entire circuit is about 60 seconds. Approximately three passes are required for fresh feed to report as product. Segregation of the tracer pellets in the system, according to their diameter, was observed and reasons for this are suggested. These results should be of potential use in the modeling and control of ball balling circuits in the iron ore industry.

Jan 1, 1985

By Jack E. Fraley

Poor lubrication reduces the life of wire hoist ropes when they are used in corrosive environments. Although lubricants are added to ropes during the manufacturing process, these lubricants can deteriorate during use, and it is often necessary to add more lubricant to both the interior and exterior of the rope while it is in service. The U.S. Bureau of Mines evaluated the effectiveness of synthetic lubricants, using electromagnetic nondestructive testing (NDT) to measure deterioration in ropes while they were in service. For nonpressurized lubricant applications, synthetic lubricants appear superior to petroleum-based lubricants in their ability to penetrate to the interior of a rope. Therefore, the synthetics offer better wear and corrosion protection.

Jan 1, 1990