Search Documents

By Williams, J. A.

THE Alaska Juneau mine has been developed through an adit driven at the elevation of the top of the mill and all mining is done above this main haulage level. As a result of wholesa1e"mining operations about 11,000 tons rock containing one dollar' per ton in gold is, hauled to the. concentrator during every 24 hr. Due to the method of mining, whereby a system of oreways delivers-the.ore direct from the stope to the bottom level of the mine, no tramming of ore is done on any of the upper levels. However, ;in doing exploratory drifting and crosscutting on the upper levels, the broken material is trammed by hand in 1-ton 18-in. gage cars to a nearby raise connecting with one of the several oreways. This constitutes the only tramming operation except that on the main level.

Jan 1, 1931

By Tuncel M. Yegulalp, Selamet G. Ergelebi

A description is given of a method of analysing modern mining systems in terms of reliability and their effects on productivity. Non-exponential distributions, such as the Weibull and lognormal distributions, for failure and equipment repair times are also considered. The resulting non-homogeneous Markov process is solved by the method of stages. A longwall mining system is analysed as an example.

Jan 4, 1993

By The Mill Staff

Introduction The Hollinger cyanidation mill commenced operating in June, 1912, and 49,779,978 tons of solids had been discarded by the end of 1950. The present tailing disposal plant has been in operation since 1924 and holds 39,762,250 tons. The tailing disposal plant is on the property of Kayorum Gold Mines, Limited, about a mile and a quarter south of the mill. The area available for tailing covers 640 acres and is roughly l ¼ miles long by ¾ mile wide. Tailing was first deposited on the McKay veteran claims, l mile long by 1/2 mile wide, which were later included in the Kayorum property. This site sloped from northeast to southwest, the slope amounting to 106 feet between the northeast corner and the low land to the southwest. The low land was wet and a considerable area was covered with muskeg up to 17 feet deep. It was drained by a brook running across the property in a southwesterly direction. Later, when more ground was needed, the low-lying mining claims adjacent to the south and west boundaries were acquired to allow for the extension of the plant. This entailed some extra difficulties and expense that would not have been encountered had the whole of the present site been acquired with the original purchase. At the present time, the top of the tailing deposit stands at two elevations, but eventually the tailing deposited on the extension to the original plant will be raised to the same height as the older deposit. Previous to 1924, all of the tailing was deposited on Low land and in lakes near the mil1. Between 1924 and 1926 an increasing tonnage was sent to the McKay claims until, in 1926, all of it was being sent there. In 1936, the area of the deposit was extended and shortly afterwards all of the tailing was deposited on the new site.

Jan 1, 1951

By R. L. Handy

The goal of this research was to adapt the highly successful rock borehole shear test for use in deep, small-diameter boreholes. Operating somewhat on the principle of a rock bolt, the borehole shear test measures both the expansion pressure and pulling force to give discrete measures of rock shearing strength as a function of the applied normal pressure. A new instrument was designed and built to fit into a 2-3/8 inch diameter hole. Unfortunately the design became so complicated, the operation is nut reliable. This is attributed to constraints of the small hole, and added requirements of an in-hole anchor to push against, and a rotating shear plate cleaner for repeated tests down-hole. A clue to the d: vice complexity is its length, which is over 10 feet. Furthermore it employs concentric cylinders and one hydraulic cylinder bored into the piston of another, or it would be even longer. Meanwhile drilling technology has advanced to greatly reduce costs of drilling 5- or 6-inch diameter holes. The downhole tester therefore should be redesigned and simplified for use in a larger diameter drill hole.

Jan 1, 1982

By Kristen R. Bingham

"Today, more than ever, drilling and blasting contractors are challenged to manage the ever-changing risks associated with blasting operations. New neighborhoods are encroaching upon mine sites and blasting projects are confronted with increasing scrutiny by permit issuing authorities and nearby residents disgruntled by new construction. The act of transporting explosives material to and from thejobsite is far from easy and trouble-free. At the same time, the pressure to stay in compliance with the growing number of government regulations continues to mount. While new tools and technology are appearing in the workplace to address some of these challenges, losses still occur. Can the datagenerated by this technology help drilling and blasting contractors make better decisions? While basic risk management principles are still applicable, do new tools and technology assist in the effort to prevent losses? What are the downsides? In this age of new technology, is face-to-face interaction still necessary? While technology is certainly a useful component in the drilling and blasting world, can it be helpful in defending claims?"

Jan 1, 2017

By Tristan H. Jones

Beginning in 1987, miniature dataloggers approved by the Mine Safety and Health Administration (MSHA) were publicly available for sale. The principal among these was the model CR21XQM, manufactured by Campbell Scientific, Inc. These dataloggers had been tested and were deemed permissible by MSHA and thus could be installed in the return air of an underground coal mine. In 1996, production of all permissible Campbell Scientific dataloggers ceased due to lack of sales. Data collection with these dataloggers has been a staple of ground control research in the United States for decades, and, without them, or a replacement, the capability to monitor ground behavior is severely impacted. Since that time, any party requiring a permissible datalogger has needed to borrow one that was purchased during the production years. In order to fill this technology gap and ensure its own data-gathering capabilities, the National Institute for Occupational Safety and Health (NIOSH) has developed and refined its own miniature data acquisition system (MIDAS). On February 16, 2010, MSHA deemed the MIDAS to be permissible and approved it for use in the return air of an underground coal mine. The MIDAS is an intrinsically safe, 16- or 24-bit datalogger, compatible with a wide range of resistive, single-ended, and differential-type instrumentation. It contains enough data storage memory to operate for over a year with typical data rates and is efficient enough to do this on a single C-sized alkaline battery for that entire period. It is menu-driven and requires no programming knowledge to operate. It supports wireless or hardwired communication for datalogger setup and data download. This paper describes the design, field and laboratory testing, and capabilities of the MIDAS datalogger. While not as fully -functioned as the CR21XQM, it is the only new permissible datalogger available, and there is intent to make it available to the mining industry for purchase.

Jan 1, 2012

BHP-Utah Coal Limited operates 33 draglines of varying sizes in the Bowen Basin of Central Queensland. The group's operations with draglines commenced in 1963 with the establishment of opencut operations at the then TPM Moura Mine and continued through expansion of that mine, the commissioning of the Utah Development Company Blackwater Mine in 1968, and the subsequent establishment of six (6) other large opencut mines, all in the general area over the next fourteen years. These operations generally commenced with boxcuts on the sub-crop at depths of 15 to 25 metres. Over the years, depths have increased so that average depths now are in the 45 to 50m range. It was soon realised that dragline operations would have to be supplemented with additional stripping equipment. In 1981, a symposium "45m and Beyond" was held in Rockhampton to assess the problems associated with such "deep" stripping. Subsequently, dragline operations have continued and although addi- tional stripping capacity has been added, in many instances, draglines have been used and are being used to dig depths greater than 45m, some- times as much as 65 to 70m.

Jan 1, 1989

By T M. Nester, D J. Reardon, A N. Page, B J. Barsanti

The load capacity of a friction bolt has long been regarded as 4 t/m of embedment for ground support design analysis and supported by in situ pull test results. In recent years, the authors have observed lower pull test results or inconsistent results which were rarely sighted in the early 2000s. The lower pull test results indicated in some cases that reliable friction bolt capacity (≥90 per cent of results) is closer to 3 t/m of embedment with some geotechnical engineers adjusting the ground support parameters in the design work accordingly. This can be in contrast with other mines which reliably obtain 4 t/m (or greater) using the same suppliers bolt in similar ground conditions. This raised several questions: • What is the effect of poor installation (bolt twist or bolt hole deviation)? • Does the performance of friction bolts vary in different rock masses? • Does bolt performance vary between suppliers? • What effect does increased jumbo feed/percussion/rotation settings have? • Have the bolt dimensions or steel strip width changed? • Have the physical bolt properties changed? • Have the steel properties changed? This paper was aimed to answer as many of these questions as possible and discuss each variable in detail. This project included friction bolt trials at various mine sites across Australia, multiple friction bolt manufacturers, steel manufacturers and laboratory analysis. The paper also includes discussion on what the authors consider best practice for pull testing. It should be noted, the terms ‘friction stabiliser’ and ‘split set’ used in this paper are used in a generic manner and is not linked to any specific ground support supplier. Whilst its acknowledged within the industry the term split set and friction stabiliser is used interchangeably, the authors acknowledge that the term split set is a trademark of Split Set Mining Systems and has been used in context in this paper.

Nov 29, 2022

By R. H. Sprute

The Federal Bureau of Mines conducted full-scale field tests in electro-kinetic dewatering and consolidation of slimes in cooperation with the Hecla Mining Co. at two of the firm's underground mines in north Idaho. To test the technique on new deposits, 4,000 ft3 of slimes from a collection sump, pumped into a watertight stope equipped with electrodes, were treated in two steps. Immediately after placement, direct current was applied using a floating electrode to hasten settlement of suspended fine particles. After removal of clarified water, the residue was further dewatered and hardened with electrokinetic treatment. In 25 hours, the material had become firm and dense with a surface capable of supporting workmen. In testing old deposits, 10,000 ft3 of slimes, placed in an unused tail drift 10 to 12 months previously, were treated. This material was sufficiently consolidated by electrokinetics to allow its removal from the mine with standard ore-handling equipment. In both tests, electrokinetic treatment densified slimes in a relatively short time with moderate power consumption.

Jan 1, 1976

By GJ Hundman

The Multiple Unit Continuous Haulage (MUCH) System was designed to provide the capacity to continuously convey coal from the mining machine to the main haulage belt. The MUCH System has an operator who steers the lead vehicle, ever following the mining machine. All the remaining vehicles follow the path of the lead vehicle, with their conveyors automatically lining up between the lead vehicle and mine section panel belt. This is accomplished by mechanical linkages on the vehicles which are interconnected by steering bars between vehicles (patent pending). The MUCH System has an operator who steers the discharge vehicle when outby travel is required. Outby travel is just like inby, with each vehicle following the path of the preceding vehicle. Surface tests overwhelmingly indicate the "UCH System should track/retrack successfully in square pillar underground room and pillar coal mines with 18 ft. wide entries and slopes up to 10 percent. For 60 degree pillar plans the minimum entry width required is 15 ft. Surface tests also indicate the MUCH System will convey over 8 TPM of coal around 90 degree corners without excessive spillage.

Jan 1, 1983

By Jeanne B. Percival, Paul Ramaekers, Charles W. Jefferson, Pat A. Hunt, Eric G. Potter, Katherine E. Venance, William Davis, Sean A. Bosman

"A 10-cm thick clay-rich layer near the top of the Manitou Falls Formation of the Athabasca Group is unusual in its breccia texture, alteration, and detrital mineral composition relative to the adjacent overlying and underlying sedimentary beds. This layer is composed of angular quartz grains set in an illite >> kaolinite + dickite matrix. Deformed clay-rich fragments within the layer have very similar mineral assemblages. The presence of euhedral accessory minerals including Ti-oxides and aluminophosphatesulphate minerals points to a diagenetic/hydrothermal origin. The presence of individual grains of Kfeldspar and amphibole is unusual relative to the typical Athabasca quartz arenite; originally, these minerals were probably included in detrital quartz and subsequently liberated during fracturing. The textures and alteration characteristics suggest that this layer is a hydraulically-fractured unit, which has experienced hydrothermal fluid alteration - a possible pathway distally related to uranium mineralization Une couche argileuse de 10 cm d’epaisseur pres du sommet de la Formation de Manitou Falls du Groupe d'Athabasca est remarquable par sa texture brechique, son alteration et la composition de ses mineraux detritiques qui different de ceux des couches sedimentaires sus- et sous-jacente. Cette couche est composee de grains de quartz angulaires dans une matrice composee d’illite >> kaolinite + dickite. Des fragments deformes riches en argile dans cette couche presentent des assemblages mineraux tres similaires. La presence de mineraux accessoires idiomorphes dont des oxydes de titane et des aluminophosphates-sulphates suggere que ces derniers ont une origine diagenetique / hydrothermale. La presence de grains de feldspath-K et d'amphibole est inhabituelle comparativement aux arenites quartziques typiques de l’Athabasca; initialement, ces mineraux constituaient probablement des inclusions dans le quartz detritique qui ont ete subsequemment liberees pendant la fracturation. Les textures et les caracteristiques de l'alteration suggerent que cette unite a subi une fracturation hydraulique et a ete alteree par un fluide hydrothermal - possiblement en lien avec les effets distaux de mise en place de la mineralisation en l'uranium."

Jan 1, 2013

By Tim J. A. Smith

Fundicion Refimet S.A. has operated a custom copper smelter at La Negra, near Antofagasta in northern Chile since 1993. From an initial operation based on Reverb smelting and Peirce-Smith, converting, the plant was expanded from 90 000 t/y to 160 000 t/y copper production in early 1997, by conversion to oxy-fuel smelting and use of concentrate injection on Converters. As part of this expansion a novel reverb gas cooling and cleaning system was developed and designed by Kilborn SNC-Lavalin Europe, the London, UK-based mining and metals; Office of Canada's SNC-Lavalin group. The reverb gas cooler needed to satisfy several very specific requirements including low cost, flexibility, robustness and simplicity of operation. Of particular importance was the requirement to cool and clean the ,oxy-fuel reverb gases and render them suitable for subsequent treatment in a conventional sulphuric acid plant. It was also important to avoid accretion or dust handling problems. This paper describes the key design features and subsequent successful installation, commissioning and operation of the unit.

Jan 1, 1998

By F. E. Harris

The United States produces about 30 percent of the world output of salt. Numerous deposits occur in widely separated areas, but the leading producing States are California, Kansas, Louisiana, Michigan, New York, Ohio, Texas, Utah, and West Virginia. Although no great amount of salt is produced at present in Pennsylvania, the potential sources in that State recently aroused a good deal of interest. The United States salt industry is highly organized; it comprises fewer companies than when small crude works with primitive methods and equipment eked out salt for local needs, but concentration of output brought about by modern inventions and methods of production has improved the quality of the produce greatly and accelerated production.

Jan 1, 1939

By Charles M. Pelanne

Without insulation we could not survive on this planet. This may sound like a self-serving statement but it is a fact. The blanket of air which surrounds us is a very effective insulating blanket, allowing some shortwave solar radiation to warm us during the day while retaining the longer infrared radiation at night. Our life on earth is very much dependent on materials performing an insulating function without being thought of as insulation, clothing, fur, window glass, the ice of an igloo etc. The mechanisms of heat transfer involved in these materials are analogous to those involved in engineered insulations - Engineered insulations are designed for maximum effectiveness for given conditions within the applicable retraints. Engineered insulations are very effective! As an illustration let us consider this graph (Figure 1). It represents: 1. The radiative heat transfer between two 1 foot2 (0.0932) radiantly black surfaces, one at 100F (38C) and the other at the temperature indicated on the bottom scale. This does not include the convective and conductive heat flow of the air, both of which are significant but small in comparison. 2. The heat transfer resulting from the placement of 1 inch (25.4 mm) of insulation [10 pcf (160 kg/m3) ceramic fiber] between these two plates.

Jan 1, 1976

By Boyd Wise

A jet pump injector was developed and successfully tested, thereby demonstrating the feasibility of a jet injector for introducing coarse coal into an operating slurry face haulage system: In Phase I a variety of injection concepts were evaluated, and the jet pump was identified as best, due to its simplicity, compactness and performance potential. In Phase IIA subscale jet pump injector tests were conducted, and a computer model of a jet pump injector was developed whose performance predictions correlated well with subscale test results. In Phase IIB various system configurations were defined for integrating a jet pump injector into a fully operational underground coarse slurry face haulage system, further highlighting the feasibility and practicality of such a system. In Phase III a full-scale mobile haulage vehicle embodying a jet pump injector and coal sizing equipment was detail designed into a practical vehicle with attractive performance characteristics. More importantly, fully operational full scale jet pump injector -and feeder/breaker subassemblies were tested and proven successful in their ability to down-size coal to 3" in all 3 dimensions and to consistantly provide slurry of 4217 weight concentration at 6.4 TPM throughput under a wide range of operating conditions including zero to maximum feed rate within 5 seconds.

Jan 1, 1985

By James R. Dunn

Samples were taken of industrial mineral waste materials which are potentially capable of being used for filling underground coal mines for subsidence control in the Pittsburgh and the Scranton-Wilkes Barre areas of Pennsylvania. The samples were subjected to potentially relevant standard tests which are commonly used 1n the evaluation of soil materials and mineral "aggregate materials. Measurements of plasticity, liquid limit, and gradations, particularly in the -200 mesh size range, indicated a comparative lack of clay minerals. Cementitious reactions between sources of alkali, such as calcium hydroxide or portland cement stack dust, and of silica, such as clay or fly ash, were found to occur in various mixes of high-bulk materials. Strengths of up to about 400 psi at 84 days were observed. The possibility of emplacement of high-bulk material by both turbid flow (or density currents) below water and by mud flows above water were considered and both appear to be reasonable and possibly simpler than the current mechanisms of emplacement.

Jan 1, 1977

This report discusses the nonfuel critical minerals position of the United States-both current and future (to the year 2000). We have assumed that there will be no major global disturbances-military, political, or economic-during the rest of this century. However, international relationships, strategies, and conditions that affect the supply of minerals are very tenuous, normal trading patterns can be easily upset, and national and ideological objectives can and do interfere with "normal" free market conditions. For example, the Department of Defense has reported that the Soviet Union is engaged in a strategy designed to reduce the availability of strategic minerals, through either physical disruption, market manipulation, or domination of producing or neighboring states. Although such a strategy poses serious concerns for the United States and the free world, the impacts of disruptions are not covered in this publication. Historical Perspective The modern industrial economy of the United States is founded on the production and use of minerals.* Two hundred years ago our forebears began taming a raw continent, developing a base for agriculture and a rudimentary minerals producing system. In the 19th century, with the aid of imported labor and capital, the development of America's vast natural resources was undertaken, and the transition from an agricultural to industrial society was underway. By the century's close, the United States had emerged as a great industrial power, partly through the development of such mineral resources as iron in Minnesota and coal in Pennsylvania.

Jan 1, 1983

By G. R. Hopkins

According to reports received by the Bureau of Mines, Department of Commerce, as of January 1, 1929 there were 413 completed refineries in the United States, with a total daily crude-oil capacity of 3,509,540 barrels. In addition, 14 refineries, with a potential capacity of 99,000 barrels, were being constructed. Of the completed refineries, 341, with a capacity of 3,325,890 barrels, or 95 per cent of the total capacity, were in operation; and 72, with a capacity of 183,650 barrels, or 5 per cent of the total, were shut down. The improved condition of the refining industry in 1928 was indicated in several ways; namely, in an increase in the total capacity of the completed plants, in the opening up of a few plants which were shut down during 1927, in a decrease in the number of plants dismantled, and in an increase in the number of plants under construction. The majority of the refiners have followed a steady expansion program commensurate in most cases with the increase in demand for petroleum products. Obsolete equipment has been dismantled and modern equipment has been installed, with the net result that the total capacity of the completed refineries in the United States has shown a steady increase since January 1, 1918, the date of the first Bureau of Mines survey. Between January 1, 1928, and January 1, 1929, the number of completed plants fell from 423 to 413, but their total capacity increase 259,160 barrels, or 8 per cent. This compares with an increase in runs to stills of domestic and foreign crude petroleum of 10 per cent, and of domestic crude alone of 7 per cent.

Jan 1, 1929

By M. S. Cetiner

This report describes the prototype development If a medium to high voltage coupler, suitable for underground coal mining operations. The coupler has such unique features as automatic dust covers and continuous phase pin shielding. The coupler is rated at 7500V and 250A continuous operation.

Jan 1, 1982

By W. Stark

Many developing countries with little or no previous environmental regulation are now promulgating air quality regulations which require facilities to demonstrate compliance with both process parameter based emission limits and ambient air quality standards. For many companies with operations in developing countries, an air quality compliance program at the facility level is lacking and these companies have very little background information to work with in developing a program for assessing and maintaining compliance. This paper will present a methodology for development of a comprehensive air quality compliance program for operations located in developing countries with new environmental regulations. The experiences of the authors in developing an air quality compliance program for a mining operation located in South America will be used as a basis. A program for meeting new air quality requirements can be developed in seven steps. The seven steps are: (1) regulatory review and project scope; (2) design and implementation of a baseline air quality monitoring program; (3) site visit, (4) development of a complete air emission inventory; (5) dispersion modeling; (6) compliance analysis and compliance plan; and (7) project completion.

Jan 1, 1998