Search Documents

By E. Morgan Massey

Located in virgin coal acreage near Gilbert, W. Va., Massey Coal Mining Co.'s Ben Creek No. 2 mine afforded the company's engineers the opportunity of designing and laying out the entire mining operation from the mine faces to the railroading loading site. However, the topography of this region posed difficult problems in haulage of coal for, in this extremely rugged terrain the uppermost coal seams lay in the mountain-top ridges, approximately 1400 ft above the valley floor. The decision for mining equipment naturally leaned to the new high-capacity continuous miners where seam conditions permitted: otherwise, to the new super-high capacity conventional cutting and loading machines. Since the coal seams lay in ridges and points of considerable outcropping, the decision was to keep the transportation on the surface and mine the coal with multiple entries into the outcrop. This way, the major problems of underground haulage, drainage, and ventilation are eliminated, and the opportunity to take advantage of a-c underground power becomes a much simpler proposition.

Jan 10, 1960

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"Previous studies revealed that the helix deflection reduced the end bearing capacity of screw pile in dense ground even if the installation process is completed with minimal soil disturbance. The ultimate end bearing capacity in dense ground is difficult to achieve during the full-scale pile load test due to the limitation of the loading system. Therefore, in the present study, model scale of testing is selected to investigate the effect of helix deflection on load settlement behavior of single helix screw pile under increasing stress level. It is observed from the test results that the applied surcharge pressure, which is used to simulate the effect of stress level, is decreased with increase in model ground thickness. This decrease in the stress level is due to the frictional resistance between the container wall and sand. It is also observed that the end bearing capacity of screw pile increases with the increase in stress level but at gradually decreasing rate. The test results indicated that the helix deflection during the pile load test should not be more than critical deflection (0.72 mm average) of the helix to avoid any reduction in the end bearing capacity of screw pile. The helix deflection, which is measured after the pile load tests are also compared with the equations of flat circular plate having uniformly distributed load over the plate with simply supported and fixed inner edges.INTRODUCTIONThe screw pile consists of a central steel shaft with one or more helices attached at different location on the central shaft. The installation mechanism of screw pile consists of torque and pushing force. The screw pile installation mechanism can affect the unit weight of the ground during its installation. This effect is small in cohesive soils but it is quite noticeable in loose to medium dense sands (Adams 2011; Santos et al. 2013). The pushing force should be controlled in such a manner that pile penetration should be at least 80% of the pitch of the helix, during each revolution (Perko, 2009)."

Jan 1, 2017

This is what I term ... the graveyard end of any Conference. It's almost over. Those of you remaining are either all talked out or past the information overload stage. And some of the sensible? ones have left for more exciting field trips, or gone back to their work-site where they earn their daily crust, or headed off South to another Conference of interest to the Energy sector that is being held currently in Christchurch. But that's OK. I have a thick skin! And neither am I particularly Politically Correct! I am not a miner: I am not involved in the mining industry in a hands on way at all. I am not even an academic. I am not even too sure why I am here ... apart from the fact that I agreed to come! At various times in my life I have been a D istrict Councillor, Chairman of a Regional Council and even an MP. I am a supporter of responsible mining.  All of what I have to say is my own point of view rather than that of either the Coal Producers' Federation or the mining industry. That is not to say that we are often in agreement, but I thought I would clear that point right at the outset. And some of what I will talk about will not strictly be to the topic - it's hardly mind-bending riveting stuff. Well, is it? But obviously because you are still here you have some interest in the topic.

Jan 1, 1997

By J P. Ashby

Compared with elsewhere in the world, New Zealand quarries have tended to be mostly small. The reasons for this are a combination of the relatively high transport costs, low population density and a pioneering, self-employed attitude. The small size of the operations is reflected in low productivity, a tendency to repair and rebuild equipment rather than replace it, designed flexibility in the processing plant, minimal reserves investigation or development planning and a versatile and innovative work force who are generally not professionally trained. The Resource Management Act and the Health, Safety and Employment Act as well as a customer driven demand for higher quality and consistent products will have even greater influence upon future direction of the Industry. The trend will be towards fewer quarries operated by companies and professional managers that can adapt to the new demands.

Jan 1, 1993

By T. S. Grewal, S. C. Gupta, H. Natarajan, T. W. McQuade, N. Nejibulloev-Mamedov

Cigar Lake is one of the world’s largest high-grade uranium mines. The ore mined at Cigar Lake is milled at Orano Canada Inc’s (Orano) McClean Lake mill. The average Cigar Lake ore uranium grade since the start of mining activities in 2014 is 17.8% U (range 8– 28%). To achieve budgeted production of 18 M lbs U3O8/yr the required average feed tonnage to the mill is about 45 kt/yr. Arsenic, occurring as arsenides and sulpharsenides, is one of the major elements of concern associated with Cigar Lake ore. The leaching process is a sulphuric acid leach under oxidizing conditions at near atmospheric pressure. The presence of arsenic in the ore consumes oxidant in leaching as well as ferric sulphate in tailings preparation for arsenic sequestration. The average arsenic grade since the start of mining at Cigar Lake is 0.57% As. Further, the ore is hosted in a matrix of sandstone and clay, which results in poor settling in CCD. The average uranium grade for the balance of Cigar Lake Phase 1 ore is expected to drop to 12.5% U and the average arsenic grade is expected to increase to 1.6 % As, with an annual average peak of 2.5%. Therefore the tonnage throughput required to sustainably meet the production target will increase to 55 kt per year. Orano partnered with Hatch Ltd. (Hatch) to perform a gap analysis study to identify key circuits and equipment in the mill that would require debottlenecking. A METSIM mass balance model of the McClean Lake mill was generated and validated with actual mill operating data. Various feed scenarios were then studied, and the outcome was a traffic light table, which highlighted feed scenarios that exceeded installed capacity of major equipment and circuits. The results provided the basis for the PDC for the pre-feasibility study. This paper will outline the results of the gap analysis, the mass balance model, the feed scenarios and the study undertaken to prepare the McClean Lake mill for the change in ore quality from Cigar Lake.

Jan 1, 2020

By R. Burrell, N .. L. Lapp

"Except for asthma and pulmonary infections, the types of lung disease that have been of immunologic interest the longest are the various mineral pneumoconioses. Because of their chronicity, type of pathology produced, and well-known immunotoxic properties associated with the dusts inciting them, the pneumoconioses have long drawn attention to the possibility that the immune system has not only been modulated but that its effectors have possibly contributed to their pathogenesis. All of the mineral dusts reviewed here have definite immunomodulating properties and act on various cellular and molecular components of the immune system. Further, each has an immunotoxic potential to induce either hypersensitivity (as in the case of beryllium) or other types of immune injury. This article reviews the immunologic aspects of the four major occupational minerals that have an immunologic impact on the lung: asbestos (particularly chrysotile), silica or quartz, beryllium, and coal mine dust.These agents have many things in common, yet each is distinctive. Although the possibility still exists that these mineral particles can adsorb intrinsic tissue antigens or extrinsic organic antigens to their surfaces and initiate immune responses to the adsorbed antigens, only one, beryllium, can act as an antigen itself. Silica is a profound macrophage toxin and thereby exerts many effects on those factors controlled by macrophages. Asbestos has undergone the most immunologic studies resulting in a much dearer picture of how it may contribute to immunopathology. Coal mine dust is the agent about which least is known immunologically, partly because there is no such thing as purified coal mine dust or a standard by which coal mine dust can be defined. Indeed, there are studies that use only the dust from the ground coal itself, whereas other studies use the total dust collected from air samples of a working mine in the belief that other types of dusts (e.g., silica from roof bolt drilling, from sand ground on the rails by cars, and from surface drilling) contribute to the disease (Figs. 1 to 5). This properly is coal mine dust and is poorly characterized. Yet, workers exposed to these dusts share similar reactive characteristics and they may be considered collectively as well as individually."

Mar 1, 1992

Evaluation of Grinding Medium Wear in Stirred Mills The standard fine grinding machines in the minerals industry are stirred mills whose performance largely depends on the competency of the grinding medium. Medium wear in stirred mills is one of the key parameters for medium selection. A wear evaluation methodology is developed and applied in this paper to measure the wear rate of river sand using a laboratory batch stirred mill. The procedure is demonstrated by testing the sand medium in a 0.55 kW batch stirred media detritor (SMD). The sand wear rate determined in the laboratory batch mill is successfully scaled up to that determined on a full-scale Metso 355 kW SMD mill.

Sep 13, 2010

By S. Kwon

When an underground excavation is created near to an instrumented measuring location, deformation at the location increases. The characteristics of this deformation increase, as well as the duration of the influence caused by the adjacent excavation, is dependent on parameters such as opening geometry and measuring location. In this study, neural networks were applied to investigate the deformation increase and the influence of each parameter on the deformation change derived from extensometer measurements at the Waste Isolation Pilot Plant (WIPP) site in New Mexico, USA.

Jan 1, 1998

By Anthony T. Eyton

Intelligent Systems: Advantages for Mining ? Increased safety (reduced risk to workers) ? Increased productivity (reduced downtime) ? Reduced maintenance costs ? Customized solutions for different mines ? Growing acceptance among mine managers A Typical Precarn Project ? Meets definition of intelligent systems ? Involves at least two Precarn members ? a technology developer partner and a user partner ? in a true collaboration ? Involves at least one university and may have various other players ? Leads to a demonstrated prototype ? Costs $2-4 million, and lasts 12-30 months ? Gets up to 40% of its funding from Precarn (max. $1 m) ? Produces new intellectual property -- owned by the project team

May 1, 2002

By L. L. Seigle

Free energies, heats, and entropies of mixing of solid Fe-Au alloys have been measured by the galvanic cell method between 800° and 900°C. A positive deviation from Raoult's law and a large excess entropy of mixing were observed, both attributable to lattice distortion caused by the disparity in component atom sizes. Since the terminal solid solutortiontions are not regular, thermodynamic properties computed from the location of the mis-cibility gap do not agree well with measured quantities. The electromotive force data suggest some changes in the existing Fe-Au phase diagram. ALTHOUGH a considerable amount of information has been accumulated about the thermodynamic properties of metal solid solutions which exhibit negative deviation from Raoult's law, particularly those in which ordering occurs, relatively few experimental measurements have been made on solutions with positive deviation. This is due to the infrequency of broad homogeneous regions suitable for experimental measurement in solutions of this type, since any marked positive deviations from ideality lead to restricted solubility and the formation of miscibility gaps. Thermodynamic data reported in the literature for such systems have usually been calculated from the location of the miscibility gap boundaries under the assumption that the entropies of mixing are ideal, i.e., the terminal solutions are regular.' One of the few binary systems with both positive deviation and a wide homogeneous range in the solid is the Ni-Au system. A recent investigation of solid Ni-Au alloys' revealed that the entropies of mixing were much larger than ideal and consequently thermal data computed from the phase boundaries assuming regular solutions were seriously in error. Theoretical considerations put forward by Zener indicated that high entropy values should generally be associated with systems possessing a miscibility gap in the solid, when this is due to differences in the size of component atoms. These facts suggest that the regular solution assumption is a poor approximation for many solid solutions with positive deviation and that reliable thermodynamic data generally cannot be obtained by conventional methods from the location of miscibility gap boundaries. The Fe-Au system, Fig. 1, resembles the Ni-Au system in certain respects. The presence of a miscibility gap in the solid indicates a large positive deviation from ideality, but there is nevertheless an extensive single phase region suitable for experimental measurement. The following investigation of solid Fe-Au alloys was carried out in order to obtain additional data on the thermodynamic properties of metal solid solutions with positive deviation from Raoult's law and to further compare thermodynamic data computed from miscibility gap boundaries with those measured experimentally. Experimental Method The thermodynamic properties were derived from measurements of the potential developed between pure solid iron and Fe-Au alloys in a high temperature galvanic cell. The experimental apparatus and technique were the same as those used for the Ni-Au alloys and described in a previous report.' Cell electrodes were 1/16 in. diam rods swaged from chill-cast ingots and annealed for one week at 850°C. The alloys were prepared by melting fine gold granules under argon with pure iron obtained from the National Research Co. The cell electrolyte was

Jan 1, 1957

By M. J. Nicol

Mr Vegter has analysed, in some depth, the approximations made in the treatment of the kinetic data presented in the original by ourselves (ref.1) and has come to the conclusion that ?under the experimental conditions used by Adams and Nicol (1986) the steady-state assumption was inaccurate?. We are acutely aware of the fact that the experimental method adopted does not permit the attainment of a true steady-state in the elution reactor. However, this does not eliminate the attainment of a pseudo steady-state by a suitable choice of the experimental parameters with the accompanying simplification of the analysis of the data with the aim of drawing the reader?s attention to the most important objective of the paper viz. the effect of various operating parameters on the rate of elution of gold.

Jan 1, 1997

By C. H. Wyndham, N. B. Strydom, S. Benade

A group of 23 underweight men weighing less than 50 kg were subjected to an acclimatization procedure in which the work rate was gradually increased from 35Watts on the first day to 70Watts on the eighth day. Excessively high body temperatures and heart rates were observed on these subjects throughout the acclimatization period and on their performance they must be rated as heat-intolerant. It can be concluded that such underweight men should not be subjected to acclimatization at such high work rates and that they should not be allocated to tasks involving these rates in a hot environment. The fact that their body surface areas are inadequate to enable them to get rid of the internal heat produced during strenuous work plus their low work capacities are the major reasons for their inability to tolerate heat.

By H. A. D. Kirsten

Written contribution by L.J. Besaanst I am a Mechanical Engineering Technician (T3), and wish to further my education to at least NHD (T4) level. I read your paper in the Journal of The South African Institute of Mining and Metallurgy with great interest, and must compliment you on its brilliance. However, there are some questions I should like to ask, and certain points I should like to highlight. I should appreciate your comments. Written contribution by J.F. Curtis The comprehensive and finely detailed survey of, and proposals for, engineering education in South Africa reflects the author's wide experience in the needs for, and the provision of, such education. This paper wil make a major contribution to the enhancement of the profession of engineering and the improvement in quality of engineering activities in South Africa. Contribution by G.W. Annandalet I have studied your paper in some detail, and am of the opinion that it makes an important contribution to the topic of the development of technological manpower, which is currently being debated in South Africa at al levels. Debate on this topic has risen above the level of academic discussion; it has been discussed by the Economic Advisory Council of the President, and is being considered at Ministerial level. Author's reply to L.J. Besaans Thank you for your contribution and complimentary remarks. As you have pointed out, there are certainly many aspects that will have to be addressed in the resolution of the crisis in engineering education. I trust that the following comments satisfactorily answer the queries you have raised. Author's General Comments Since publication of the paper, attention has become focused on the provision of employment opportunities an aspect not dealt with specifically in the paper. The following comments serve to indicate some of the directions in which job opportunities will have to be developed in the numbers that will be required.

Jan 1, 1991

By W. Greg Maybee

Separations, which form along stratigraphic boundaries in the roofs of potash mines, pose a serious safety concern. If these separations go undetected they can lead to falls of ground. The current method of identifying the location and extent of these separations is through manual scaling (sounding) using an aluminium rod. The potash mining companies would like to have a tool, which could quickly and reliably detect these separations and distinguish between them and clay seams. This paper presents the results of field trials undertaken at various potash mines in Saskatchewan belonging to the member companies of the Saskatchewan Potash Producers Association. A ground penetrating radar instrument from RST called SUSI (stepped frequency, ultra-wideband, synthetic aperture radar instrument) was used. SUSI has the ability of working over various frequency bandwidths. Four mines were chosen for these field trials, covering the different geological characteristics encountered in the Saskatchewan potash mines: Potash Corporation of Saskatchewan?s (PCS) Allan and Lanigan Divisions, Agrium?s Vanscoy Potash Operations and IMC Potash?s K2 Mine. These field trials indicated that stepped frequency ground penetrating radar technology could be ?tuned? to identify both separations and clay stratigraphy in the softrock, potash mine environment, based on the different spectral responses of the features.

May 1, 2004

By Sergio Neves Monteiro

This work had as its objective the characterization of a waste material, steel slag, generated from an integrated steel plant, with a view to its recycling and incorporation into red ceramics fabrication. The characterization was performed in terms of chemical composition by X-ray fluorescence (XRF), particles size distribution, X-ray diffraction (XRD), thermal analysis (DTA/TG) and scanning electron microscopy (SEM). The results indicate that the steel slag presents high amount of Ca, Fe, Mg and Si. The weight loss of the steel slag at temperatures above 800oC is associated with calcium carbonate decomposition. The coarse particle size of the steel slag is inadequate for its direct recycling into red ceramic fabrication. It is necessary to screen or to grind the waste. As a possible solution, it is suggested that screening or grinding the steel slag to a convenient particle size distribution would allow its successful industrial incorporation into red ceramics products.

Jan 1, 2006

By Moskovits E. E

Spodumene was recovered from pegmatite by flotation in laboratory and pilot-plant tests using an anionic collector emulsion. A similar process applied to beryl pegmatite gave encouraging results.INTRODUCTIONOver the past two decades lithium and beryllium have aroused increasing interest in the metallurgical world. Both these light metals have potential uses in nuclear shielding and cooling and in lightweight alloys, and there is a growing demand for lithium chemicals for ceramics, air conditioning and lubricants. The use, technology and history of lithium has been surveyed by Schreck (1961).For many years, the only commercial production of lithium and beryllium was from pegmatite deposits amenable to hand cobbing. The most important minerals of these ores are spodumene and beryl, which are respectively lithium aluminium silicate and beryllium aluminium silicate. Norman and Gieseke (1940) investigated the treatment of lithium ores by froth flotation. The process of flotation of the pegmatite constituents away from the spodumene was applied commercially in 1951, and the operation has been described by Goter, Rainey and Hudspeth (1953). Subsequently, the flotation of the spodumene from the pegmatite was studied by Munson and Clark (1955) and Browning and McVay (1961), and this method has superceded the reverse flotation process commercially. Muskett, Tasker and Hobson (1962), in applying the method of Browning and McVay in pilot-scale tests, reported difficulty because of activation of quartz and felspar by iron salts introduced during milling of the ore.The flotation of beryl, reported by Ashton and Weir...

Jan 1, 1963

By J L. Mauk

The Martha epithermal Au-Ag deposit contains multiple generations of quartz veins with a range of textures. We examined: +        vein textures, +        crosscutting vein relationships, and +        the paragenetic sequence within the pit walls as well as a wide range of hand specimens. Samples include host rock, breccia, and veins, but these groups are not distinct; instead, they form a continuum.   Veins at Martha mine show a wide range of textures on a local scale; these textures also change significantly over both the lateral and vertical extent of the pit. Common textures include crustiform bands, comb quartz, colloform bands, platy quartz, massive quartz, drusy quartz, sedimentary textures and brecciation.   Vein grades relate to textures. Many textures, including crustiform, platy, cherty, and sedimentary textures display predominantly low grades, but some textures are linked with high grades, such as ginguro, massive and comb quartz where they are associated with visible base metal sulphides and/or electrum. Host rocks and most breccias are low grade, as most samples contain <2 ppm Au.

Jan 1, 2006

By Stefan Norgaard

In today's modern gold mining industry in Australia, and the world, more and more companies are recognising the competi­tive advantages gained by implementing an effective training program for operations (processing plant) personnel. Plant operators, or process technicians, are unique amongst all other gold mine employees. They are at work in shifts cov­ering 24 hours a day and their actions can have a profound effect on the operation's economic performance. To a large degree, the minute to minute decisions and actions of an operator can deter­mine whether gold is extracted to bullion in the goldroom or is discharged into the tailings dam. Experience has suggested that most small to medium sized gold operations in Australia, and even some large ones, have not implemented an effective training program. This is not attrib­uted to deliberate negligence or "anti" attitudes against training, moreover mill superintendents and metallurgy managers are technical people not oriented to human resource techniques. Usually the demands of designing, constructing and commis­sioning a gold plant overshadow the need for training in the first instance, In fact some well designed plants treating friendly oxide friable ore have little need for a dynamic well trained oper­ating staff. However, many plants do require a thinking team to optimise production and changing ore conditions towards the end of a mine's life can expose poor competence levels at large expense. Few managers will argue that training is a necessity and results in a win-win situation. The operators win by increased job skills, job satisfaction, clear career development and possibly better pay conditions. Trained personnel usually reciprocate with increased effmt and work ethic. The company wins also by having a thinking team which will maximise gold production and reduce operating costs.

Jan 1, 1998

By R. R. Wells

An important activity of the Bureau of Mines is the continual search for new sources of minerals. As a part of the investigation of strategic mineral deposits in the United States, samples of mercury ores were submitted to the Ore Dressing sections of the Salt Lake City and Albany stations for metallurgical testing. This paper gives data summarizing the results obtained from laboratory beneficiation studies of mercury ore samples submitted during the period 1941 to 1947. Ores tested included three from Jackson County, Oreg., one from Valley County, Idaho, one from Storey County, Nev., and one from Sonoma County, Calif. In general, the ores from Oregon were not amenable to concentration by flotation because of intimate association of cinnabar with other minerals or because of extremely low grade. One Oregon ore was amenable to direct distillation provided lime was added to reduce corrosion of the retort.

Jan 1, 1950

By L. Shoke

The aim of this study was to develop an in-house tensile testing procedure that would yield accurate and reproducible parameters as input material properties into computational models for numerical simulations of the mechanical behaviour of TM380 mild steel. To achieve this objective, we reviewed the ISO 6892:2009 tensile testing standard along with reported good practice guidelines. Tensile tests were conducted on a dog-bone shaped TM380 mild steel specimen with strain gauges attached on either side, to monitor alignment and measure strain, using three different types of tensile testing machines. Parameters quantified included yield stress, ultimate tensile strength, and modulus of elasticity. The values of these parameters were found to be in agreement with the values supplied by the manufacturer's specification and showed minimal variations between laboratories. Thus it can be concluded that the tensile test procedure used resulted in accurate and reproducible results. The strain values calculated as per standard were in disagreement with those determined from extensometer and strain gauges and resulted in lower elastic modulus values. This confirms that the current testing procedures require the use of long-range strain gauges or extensometer to determine the strain. A chemical analysis was conducted to verify the specification by the manufacturer. The specimen was found to be fairly homogeneous with minor sulphide inclusions. The micrographs reveal a pearlite and ferrite structure typical of mild steel, and the fractographs show a dimpled surface typical of ductile fracture, which is an attribute of mild steel.

Jan 1, 2013