Search Documents

By M. Moinpour, E. Liao, C. Y. Aw, D. J. Brown, P. W. Cheung

"Currently, silicon-based insulated-gate field-effect devices are being widely developed as the basic structural elements in a new generation of chemical microsensors. In this paper, we discuss some of the process considerations related to the fabrication of the Chemically Sensitive Field-Effect Transistor (CHEMFET). This ion-sensitive CHEMFET (or ISFET as it is often called) can be used for pH measurements (i.e., as a pH sensor) when the gate insulator of the electrolyte/insulator interface is made of Si3N4 obtained by the LPCVD method. Effects of processing parameters such as the Si3N4 deposition rate, gas composition, total flow rate, annealing treatment, etc. on Si/Si02, Si/Si3N4 and Si/Si02/Si3N4 structures are discussed in relation to the CHEMFET fabrication. Their effects on the electrical characteristics and chemical response of the sensor are also examined. Capacitance-Voltage (C-V) measurements and ESCA analysis have been used to interpret the results. The Si3N4/Si02 double dialectric layer provides improved ion blocking for the gate insulator in electrolyte solutions with enhanced pH sensitivity over time. The stability and performance of the fabricated CHEMFET sensors were tested by measuring the pH sensitivity in various storage conditions. The SEM analysis was used to evaluate the hydration effect at the ISFET's gate insulator with respect to different storage conditions.IntroductionThere has been a continuous interest in the development and fabrication of various chemical microsensors for chemical and biomedical applications over the last fifteen years. The application of semiconductor (particularly silicon) technology to the area of sensor fabrication has led to an emergence of a new generation of miniaturized, microelectronic, solid-state chemical sensors. There are numerous clinical situations where continuous monitoring of body electrolytes concentrations such as Na+, K+, Ca+2 , etc. and blood gases (pH, Po2 , and PC02) would be essential for the effective diagnosis and management of patients under critical conditions. Solid- state microsensors can be used for direct and continuous in vivo measurement of the above parameters in most instances."

Jan 1, 1988

By Victor deWolfe

INTRODUCTION The Henderson Mine, located near Empire, Colorado, utilizes a continuous panel caving system to extract ore as one of the world's major producers of molybdenum. Any mine using a caving-by-gravity technique of mining must rely on closely controlled draw of the caved ore. This control is essential to insure proper caving action, to avoid damaging load concentrations of weight and to minimize the dilution of ore with waste material. Henderson is no exception. Draw control is a major factor in all production planning, from long- range plans to short-range and day-to-day ore scheduling. Draw control is reviewed constantly and administered daily in an effort to optimize production efficiency, ore recovery, and cave management. MINING METHOD The cave at Henderson is massive, moving slowly through large panels that are 244 m (800 ft.) wide by 610 m (2,000 ft.) long. Generally two cave areas are drawn at one time. The areas under active draw vary in size but can be as large as 244 m (800 ft.) by 244 m (800 ft. ) containing 400 draw points. Each draw point contains 45,360 mt (50,000 st) on the average and takes about two and one half years to exhaust. A complete panel is worked for seven to ten years. No pillar exists between panels, but rather a buffer zone of broken ore, or "static face," is left in each panel to be drawn with the adjacent, yet-to-be-caved panel in efforts of minimizing dilution of a working area from an exhausted one. (Figure 1) Production drifts are driven on 24.4 m (80 ft.) centers through the ore body. Between the production drifts are funnel-shaped draw bells on 12.2 m (40 ft.) x 24.4 m (80 ft.) centers to receive ore from the cave. Each bell is accessed by two draw points, one from the production drift on either side, thus forming a 12.2 m (40 ft.) x 12.2 m (40 ft.) draw pattern. Extraction of the ore is by rubber-tired, 3.8 m3 (5 yd3) load-haul-dump equipment. The LHDs then tram the ore a maximum of 49 m (160 ft.) to ore passes. Cave initiation and bell development are done from the undercut drifts which are parallel to and 17 m (55 ft.) directly above the production drifts. Longhole rings are drilled and blasted from the undercut drifts to define the bells and establish the undercut for caving. (Figure 2) DRAW CONTROL Since the cave line at Henderson is constantly advancing, it is necessary to be continually initiating new cave at one end while exhausting it at the opposite end. There must exist, therefore, an angle on the ore-waste contact in the broken rock from initiation to exhaustion. The basic concept of draw control is to keep this angle as smooth and even as possible, particularly at the time of exhaustion. If this is achieved, draw points are exhausted more or less in a line, avoiding pockets of remaining ore surrounded by exhausted areas. These pockets would cause spotty ore extraction at the time of exhaustion, increasing the amount of dilution occurring while introducing the potential for significant weight problems in the production area. To arrive at the desired angle on the ore- waste contact, maximum tonnage percentages are assigned to each row of draw points increasing at 10% or 15% increments (depending on cave size and velocity of draw) working away from the cave line. The available tonnage indicated by these percentages is the maximum allowable tonnage to be extracted from each draw point until the available tonnage percent- age is increased. As the cave moves, these percentages increase for each draw point regularly. However, in general the tonnage drawn from each draw point is kept at about 50% of this allowable maximum in order to maintain adequate available tonnage in the cave to sustain production for seven months if cave initiation were to cease. This available tonnage cushion is a safeguard built into the draw control program at Henderson to accommodate fluctuations in the rate of cave advance. When draw points move past the row of 100% tonnage availability, they are drawn past the desired 50% at the same increments per row until exhausted. (Figure 3) To achieve proper draw control, the number of LHD buckets to be taken from each draw point is assigned daily. The actual buckets taken, which may at times deviate from the

Jan 1, 1981

By Deborah A. McCombe

"There are a number of important dates that must be disclosed when a Qualified Person (QP) is preparing a technical report for securities purposes. The dates are discussed in NI43-101 and the Form of the Technical Report, NI43-101F1. •,Effective date of the technical report •,Possible revision date of the report •,Effective date of mineral resources and mineral reserves •,Date of the personal inspection (site visit) •,Signature date of the date report (execution date) •,Date of the certificate of the QP •,Date of the consent of the QP The effective date of the report is basically the cut-off date for the information that is included in the technical report. The effective date should be close to the signature date. If there is too long a period between these dates, the QP runs the risk of new material information becoming available and then the technical report would no longer be current. The effective date is disclosed on the title page of the report and on the signature page. If a technical report needs to be revised to correct problems or disclosure deficiencies identified by the regulators, the QP will normally need to include a revision date on the title page of the report to distinguish the revised version from the original version. In these circumstances, the regulators will request that the original date of the report remain on the title page and the revised date will be below it. When a technical report must be revised, the QP must resign and date the signature page of the report and provide a new certificate and consent."

Jan 1, 2003

By E. N. Gilje

"IntroductionDURING the past five years, over two miles of shaft sinking have been completed at Falconbridge. As sinking has continued, we have improved our equipment and technique with a resulting increase in efficiency. Throughout this period, all sinking has been done by contracting firms, under our direction and to our equipment specifications, with highly satisfactory results. Since 1949, Riddell shaft mucking machines have been successfully used in conjunction with the •benching method of sinking. Our most recent practice can best be illustrated by describing the method used in sinking No. 1 shaft at the Fecunis Lake mine.No. 1 Shaft, Fecunis Lake MineNo. 1 shaft, consisting of six compartments and measuring 13 ft. 11 l/2 in. by 19 ft. 9 3/8 in., outside timber (Figure 1), will be sunk to a depth of 4,170 feet. It was designed to accommodate two 10-ft.diam. Koepe hoists."

Jan 1, 1955

By Ying Lu, Jeffrey C. Johnson, Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

Energy dissipation and fragmentation of rock is of interest for mine-to-mill operations in order to understand breakage and to minimize energy consumption during blasting at the mine site, and comminution at the processing plant. In this regard, high velocity impact breakage of long granite cores, called bars, has been studied with instrumented strain gages to follow the energy dissipation gradient along the bar length resulting from the strain waves generated by impact. As a result of high velocity impact, three zones have been identified (fragmentation, fracture, and elastic) and these three zones have been characterized in 3D using X-ray tomography. The fragmentation zones of the granite bars were studied in detail to describe the particle size distribution and the particle shape characteristics. Finally, the experimental energy dissipation for the fragmentation zone was found to be in close agreement with the expected energy calculated from the Bond work equation, if the anisotropic granite particles are defined by length rather than by sieve size.

By A. W. McReynolds

One characteristic of plastic deformation which distinguishes it from elastic strain is the essential inhomo-geneity of plastic strains. Elastic strain varies continuously through a material, and average relative displacements of initially adjacent atoms are only small fractions of their initial spacing, (strains of the order of 0.01 or less). On the other hand, plastic flow corresponds to the appearance of discontinuities in strain of the lattice, such as dislocations or slip bands, where local strain, on an atomic scale, is several orders of magnitude higher. These discontinuities are visible on a microscopic scale as the familiar slip lines (Fig 1). In spite of this obvious microscopic inhomogeneity, however, macroscopic measurements almost invariably show a smooth curve of stress vs. strain (Fig 2b) even if measurements of linear strains be made to an accuracy of one part in 107. This macroscopic homogeneity of strain indicates that the discontinuities in strain on slip planes occur in increments too small or too slow to be recorded individually, and further that they occur sufficiently independent of one another so that the small increments add at random to a smooth stress-strain curve. The present paper describes observations of plastic strain in aluminum of commercial purity and in high purity Al-Cu alloys, where there exists a strong coupling between slip in various regions of the specimen such that once initiated it spreads rapidly through a large volume. The total effect is that of relatively large, rapid, and regularly spaced steps of strain followed by periods of only elastic strain. Fig 2a illustrates the type of "stair-step" stress-strain curve which results. The properties of this cooperative slip phenomenon will be described further in the section on results: in par- ticular it will be shown that each step corresponds to the propagation of a wave of plastic deformation through the specimen. Some interpretations of the mechanism by which it occurs will be made in the following section. Although the type of plastic wave phenomena to be described has not previously been reported, there are numerous cases of related effects in the plastic yielding of metals: YIELD POINT PHENOMENA The most familiar of such effects is the "yield point" observed in low carbon steels, brass, duralurninum, and the like. It consists in the sudden termination of the elastic portion of the stress-strain curve by a large plastic strain. Since the usual tensile machine is such that yielding of the specimen relieves the load, the resulting curve is as shown in Fig 3. As the strain continues, deformation occurs at a lower stress for some time, then follows a rising curve, but with no further sudden yielding. This effect has been observed in brass by Sachs and Shojil and later by many others. Edwards, Phillips and Jones2 made extensive studies of the effect in steel, and of the role of various alloying elements. Although there seems to be fairly clear evidence that the yield point is caused by a hardening of the material by precipitation of impurities, no satisfactory explanation for the sudden yielding has been given. Winlock and Leiter3 have shown that the strain. level of the upper yield point depends strongly on the rate of loading, the yield point increasing by almost a fac- tor of two as the strain rate goes from 0.002 in. per in. per min. to 4.4 in. per in. per min. This effect would seem to imply an incubation period before yielding is initiated at a certain stress. On the other hand, by going to very slow loading rates, Edwards, Phillips and Jones2 showed that the yield point does not become lower and eventually disappear as might be expected, but, on the contrary, begins to rise at loading rates below about 25 Ib per in. per min. becoming much higher than at rapid loading rates. STRAIN AGING If, instead of continuing straining of a specimen after occurrence of a yield point, the load is removed and the specimen aged, resumption of the test results in occurrence of another yield point as shown by the dotted curve of Fig 3. The new yield stress is generally higher than the previous maximum applied stress. This hardening of the material by straining and subsequent aging is undoubtedly related to quench age-hardening resulting from the aging of a specimen quenched from high temperature. Since neither effect is observed in pure metals, it is generally accepted that quench-aging in all cases is the result of hardening by precipitation of a supersaturated alloying element, and that strain-aging is probably a similar precipitation, accelerated by disruptions of the lattice by previous strain. Pfeil4 has shown that strain-aging does not occur in iron from which all of the carbon has been removed, but that only a very small carbon content, around 0.003 pct, is necessary to cause strain-aging. In accord with this observation is recent work by Dijkstra5 in this laboratory showing that the solubility limit of carbon in iron is extremely low, less than 0.001 pct at 400°C. Edwards, Phillips and Jones2 have shown that the strain-aging effect is also removed by the addition of small quantities of elements such as Mo, Mn, Ti, and the like, which readily form carbides. Their results demonstrate the

Jan 1, 1950

By A. Ohno

"A new near net shape casting process, OHNO Continuous Casting (OCC), has been recently developed. In this process, molten metal is fed into a heated mold maintained at a temperature above the solidification temperature of the metal being cast. Solidification begins from the central core of the casting rather than the wall of the mold. With the heated mold, the formation of crystals on the mold wall is prevented and solidification occurs out of contact with the mold surface. This produces near net shaped products with smooth, mirror-like surfaces and unidirectional grain structures free from cavities, porosity and segregation. Any crystals formed at the beginning of solidification decrease in number as solidification progresses and eventually a single crystal product is obtained. This process is applicable to any metal alloys, converting them into new materials with superior properties and quality.IntroductionAs a result of growing technical demands for more advanced and diversified materials, the OHNO Continuous Casting (OCC) technology has found many new applications in industry. Considerable interest in the process has been shown in Japan and other countries because of its distinct ability to:produce a single crystal, (1)produce a remarkably clean cast surface without a witness mark,provide extremely good ductility,and reduce casting defects and segregation.This paper provides an overview of the principle of the OCC process and describes the remarkable characteristics of the material produced by this method."

Jan 1, 1988

By Sherwin F. Kelly

"THE TITLE I have chosen is certainly not one of those self-explanatory ones. I shall endeavour to make its significance clear during my remarks but, in the hope of minimizing that inevitable exodus which follows a good lunch such as this, I am going to withhold the final key to its meaning until the very last sentence of this talk.Some explanation is due at the beginning, however, so for those of you unfamiliar with Spanish I will explain that casa means house, or home. The casa about which I am going to talk necessitates a wide .and generous interpretation of the word, because I am using it to indicate principally that portion of the North American continent which is the home, in the western hemisphere, of British and American ideals of justice and freedom, the dignity of the individual and his right to exercise private initiative .and engage in private enterprise. In a wider sense, I am including the entire western hemisphere, which may yet stand as the last bulwark of political and industrial democracy.As for the treasures of which I am about to speak, may I remind you that there are no• material treasures but those derived from the earth, and they are derived by one of two processes, -mining and farming. These two fundamental industries are the basis, and the sole material basis, of our welfare, our wealth, our very existence. From farming, whether it be farming of the land. or farming of the sea, we obtain the food to keep us alive, healthy and able to work."

Jan 1, 1955

By L. C. IlsLey

Coal mining is more widely distributed throughout the United States than is generally known, as 30 States are credited with having coal mines. In 1919 twenty-three of these States each produced at least a million tons of bituminous coal, and all the States produced about 560,000,000 tons. In addition, Pennsylvania produced about 85,000,000 tons of anthracite. Twenty-eight States have regulations prepared by commissions or have enacted laws governing the operation of coal mines. Pennsyl¬vania has separate codes for the anthracite and bituminous fields. The codes may be classified as follows: Twelve distinctly coal¬mining codes; eight codes that are essentially coal mining, but also apply to other mines; five codes that are subdivided, referring partly to coal mines and partly to other mines; and four codes that are essentially metal mining, but apply in part or in whole to coal mining. The first State to have a coal-mining law was Pennsylvania, which enacted a law, for Schuylkill County only, in 1869. The first State to enact a coal-mining law governing all the coal mines in the State was Illinois in 1872, followed by Ohio in 1873. Pennsylvania in 1879 enacted a law for anthracite mines only, but did not enact similar laws for bituminous mines until 1577. At least 10 other States enacted coal-mining laws between the years 1870 and 1890. Before 1890 electricity was little used in coal-ruining operations and therefore practically no provisions governing the installation, inspection, or maintenance of electrical equipment were made in any of the laws enacted up to 1890. In the law of Colorado, approved April 8, 1885, there is a reference to the use of telephones, probably the first reference to electrical equipment of any kind in a State-mining code. Most of the mining codes have been changed from their original form by amendment or by complete revision. In some of the early changes a casual reference is made to the use of electricity or to the handling of electrical equipment. In 1911 Pennsylvania added

Jan 1, 1920

By Jamey B. Rosen

As Project Information Management Systems (PIMS) technologies develop, the range of projects to which one can apply these technologies grows while the cost to apply them shrinks. In recent years, technologies previously limited to large “megaprojects” (e.g., major dam rehabilitations) owned by major entities (e.g., the United States Army Corps of Engineers) with large budgets have been applied to smaller projects with less stringent specifications and more modest budgets. This paper will describe applications of PIMS technologies to small projects with limited budgets, including examples from levee construction, small-scale grout curtain installation, and diaphragm and secant pile cut-off walls. We will include a demonstration of how PIMS technologies can effectively analyze verticality data from koden and hydromill data streams to automatically generate models and as-built drawings showing overlap and deviation along the depth of the foundation. INTRODUCTION This paper discusses the application of Project Information Management Systems (PIMS) technologies to geo-foundations projects, with a focus on technologies and examples that are in a lower cost range. PIMS technologies allow contractors and other stakeholders to perform efficient quality control on their data, generate quick or automatic reports and as-built drawings, perform analyses to better understand their construction, and ultimately use their data to increase the quality of their construction. As PIMS technologies are relatively new to the deep foundations industry, and owner specifications on their use are generally viewed as complex and limited to large scale projects, PIMS technologies are frequently viewed as an expensive component that is beyond the scope of a smaller or simpler project. However, the same principles and techniques generally associated with large projects can be applied to projects at smaller scale. Furthermore, as these technologies develop both in the deep foundations and other industries, the cost of application is decreasing quickly making them even more affordable for smaller projects. The remainder of this paper provides some justification for applying PIMS technologies, describes some scalable data management concepts and workflows and then provides some examples of “low cost” applications of these technologies.

Jan 1, 2019

The activiltion of sphalerite with electrolytically generated copper ions from a copper electrode instead of the usual practice of the addition of copper sulphate was studied in the laboratory. A large surface area of copper was provided by lining three sides of a bench flotation cell with copper sheeting. The lining was connected to the positive terminal of a low voltage d.c. source, and the cell impeller to the negative terminal.Sphalerite was effectively activated by this arrangement and was subsequently floated using xanthate as the collector.Flotation results comparable to those obtained with 1 lb/ton CuS04.5H20 (0,255 lb/ton copper) were obtained using 0·1062 lb/ton of electrolytic copper and 0·488 kWh of electrical energy. The wastage of copper due to the formation of insoluble precipitates was found to be dependent on the length of time the current was passed. Maximum current was passed for the shortest time to minimize wastage.

Jan 1, 1973

By R. E. Ogilvie, N. L. Peterson

Diffi-lsion measurements were conducted at all compositims in the bcc solid solution of the U-Nb system employing incremental couples at composition intemals of 10 at. pct. Diffusion coefficients were determined by the Matano method from concentration gradients obtained with the electron-probe microanalyzer. The activation energy for inter-diffi-lsion as a function of compositim shows three distinct regions: 1) 80 to 100 pct U.6= 30 kcal per mole; 2) 20 to 80 pct U, $ - 70 kcal per mole; 3) Oto 20 pet U, Q = i40 kcal per mole. The frequency factor, fi0 and the activation energy $ were found to be roughly related by the following equation: log Do ^9.7 X IO-5Q -6,6. The Kirkendall marker movement indicates that DU is larger than DNb between 16 and 100 pct U and DNb is larger than DU from 0 to 4 pct U. FOR practical as well as fundamental reasons, the rates of diffusion in alloys are of considerable consequence. Most solid-state reactions are largely dependent upon the diffusion of atoms through the lattice structure and along grain boundaries. The high-temperature strength and reasonable nuclear properties of niobium have prompted its use as a reactor material in contact with uranium fuel. Hence, diffusion data for the U-Nb system are of considerable importance. In the previous diffusion study1 on the U-Nb system using pure element couples, reliable data were obtained only in the range of 0 to 10 at. pct Nb due to the large variance of the diffusion coefficient with composition. Also, a large Kirkendall effect and considerable porosity in the uranium-rich areas of the specimen were reported, which suggests that the true diffusion coefficients are somewhat larger. The purpose of the present study was to obtain reliable diffusion coefficients at all compositions using incremental diffusion couples with intervals of 10 at. pct. In view of the abnormal self-diffusion be- havior of y uranium2-4 and some other bcc transition elements,&apos;-&apos; it was felt that a comparison of the interdiffusion coefficients in the bcc U-Nb system with those of Reynolds et al.9 for the fcc gold-nickel system might shed some light on the diffusion mechanism involved. Both systems have similar phase diagrams, in that complete solid solubility exists above a miscibility gap. EXPERIMENTAL PROCEDURE The uranium used in this investigation was obtained through the courtesy of Argonne National Laboratory. An analysis of this material detected only Si-30, A1-7, C-6, N < 10 and 0-18 ppm. The niobium was electron-beam melted material obtained from Stauffer-Temescal. The gaseous impurities were less than 50 ppm, and the spec troc hemical analysis showed Ta-500 and W-200 ppm. U-Nb alloys were prepared at composition intervals of 10 at. pct by melting the appropriate amounts of the pure elements in an arc furnace. The buttons were inverted and remelted 6 times to assure complete mixing. The buttons were then wrapped in molybdenum foil, canned in Zircaloy-2 or stainless steel, and hot rolled 30 pct reduction in thickness at temperatures between 850" and 1100°C. Alloys with 10, 20, 30, 40, and 90 at. pct Nb rolled quite easily under these conditions, but the 50, 60, 70, and 80 pct alloys remained brittle. After melting and rolling (when possible), the alloys were annealed for 24 hr at a temperature within 100°C of their melting point in a dynamic vacuum of better than 4 x 10-8 mm Hg. These treatments produced alloys which were homogeneous on a 1 p scale within the detectability limits of the electron probe. During fabrication, the alloys picked up as much as 100 ppm Mo and 100 ppm Zr. Other elements checked for but not found were Co, Cr, Fe, Mn, Ni, and Ti. The grain size of the annealed samples ranged from 3 mm for the uranium-rich alloys to 0.3 mm for the niobium-rich alloys. This permitted measurements of the concentration gradients in the diffusion samples without crossing more than one or two grains, thereby eliminating any grain boundary effects. The specimens were bonded by theU&apos;picture frame" technique as reported by Kittel.10 Specimens of composition b)U + (100 - x)Nb were sandwiched between two specimens of composition (x + 10)U + (90 - x)Nb after they were ground flat and parallel

Jan 1, 1963

By P. M. Solozhenkin, O. I. Solozhenkin

Currently lead nitrate is used as the recommended activator in Au-Sb flotation. However, due to high levels of hazard, the application of lead nitrate constitutes a potential risk for human health and ecosystems. To mitigate the harmful impact of activators on the environment, further research on activation by alternative reagents has been launched to promote the efficiency of antimony ores. In the present study, adsorption of lead, copper and zinc cations has been investigated by nuclear quadrupole resonance (NQR), which has revealed copper and zinc cations penetration into the mineral lattice, although lead cations remain adsorbed on the mineral surface. However, the combination of zinc and copper cations leads to preferential volumetric adsorption of zinc in the mineral lattice and further surface adsorption of copper which positively affects the activation process. It has been established that activation of stibnite can be achieved effectively with the mixture of Cu2+:Zn2+=1:1 as much as with lead cations in antimony ore flotation. As a part of this work, the computational modelling has been used in prognosis of reagent activity evaluation (PRAE) for stibnite and aurostibite flotation by sulfhydryl collectors. The lower PRAE value the stronger the ability of a collector to form a stable complex with a mineral. PRAE has shown a strong negative trend to complex formation on the mineral surface of aurostibite and stibnite. Based on these studies, several collectors have been proposed for effective flotation. To verify the feasibility of proposed collectors tetramethyl (ethyl) thiuram disulfides (TMTD and TETD) have been used for flotation of stibnite, sphalerite, pyrite and arsenopyrite. Flotation performance has been improved significantly with TMTD that allows the avoidance of lead nitrate application and increases the recovery of antimony by 8,16%. Keywords: Stibnite, aurostibite, activation, lead, copper, flotation reagents

Jan 1, 2020

By L. C. Brown, C. St. John, C. C. Sanderson

The diffusion rate in Cu-Te couples is very sensitive to compressive stress, with a load of 20 psi making a significant difference to the width of the diffusion zone. At zero stress, two phases appear in the diffusion zone (Cu4Te3 and CuTe). Under compressive loading the third stable phase (Cuz Te) also appears, and its thickness increases progressively with increasing stress. The results are explained on the basis of an incipient Kirkendall porosity which restricts the transfer of atoms from the copper into the diffusion zone. DURING a study of the Kirkendall effect in Cu-Te couples prepared by clamping together the two components, it was found that the diffusion-zone width and shape in the plane of contact were not reproducible. Although the stresses involved in clamping are not normally sufficiently high to affect diffusion rates, preliminary tests established that the Cu-Te system is particularly stress-sensitive. The phase diagram for the system Cu-Te given in Hanssen1 shows that there is practically no solid solubility at either end of the phase diagram. Many areas of the diagram are not fully substantiated, but there appear to be three intermediate phases: Cu,Te—hexagonal in structure, having a grey luster; Cu4Te3—a tetragonal defect structure, having a red-purple luster; CuTe—orthorhombic in structure and having a golden-green luster. The existence of a fourth phase, the X phase at 37 at. pct Te, is considered doubtful. The composition ranges of the three stable phases are small, and are not accurately known. The phase diagram changes little with temperature up to 305°C, at which temperature a polymorphic transformation takes place in Cu2Te. The nature of the Cu-Te phase diagram indicates that the diffusion zone in a Cu-Te couple would consist of a series of layers of intermediate phases. The relative thickness of any one phase will depend on its diffusion coefficient and composition range.&apos; In this type of diffusion couple it is often found experimentally that some phases are not visible at all in the diffusion zone due either to a small diffusion coefficient or to a restricted composition range.3 Since the composition ranges of the phases in Cu-Te are not known, it is not possible to determine diffusion coefficients in this system from a knowledge of the phase thicknesses. Several investigations have been carried out to determine the effect of compressive stress on diffusion rates in multiphase systems. Diffusion couples of Ni-A1 have been investigated by Storchheim et al.4 and by Castleman and Seigle.5 Two phases (ß and ?) appear in the diffusion zone under zero stress and the thickness of both phases is progressively reduced with increasing stress. According to Storchheim et al.4 a stress of 25,000 psi reduces the thickness of the diffusion zone by 50 pct. In a-brass—?-brass couples the thickness of the 0 phase formed in the diffusion zone was reduced by 20 pct at a stress of 20,000 psi.6 In other investigations the compressive load has been observed to increase the width of the diffusion zone. In A1-U, several investigators3,8 have found the width of the whase UA13 to increase with stress. According to casileman,8 the rate of formation of UA13 at 520°C is 75 pct faster at a stress of 20,000 psi as compared with a stress of 2500 psi. In Cu-Sb the effect of stress is greater than in the other systems described. According to Heumann9,10 only one phase (y) appears in the diffusion zone at a stress of 500 psi, but at a stress of 850 psi two phases (y and k) are present. If a diffusion couple containing both y and k phases is annealed at a low stress level, the y phase grows at the expense of the k phase. EXPERIMENTAL The diffusion couples were prepared from electrolytic copper bar stock with a nominal purity of 99.92 pct and from tellurium of 99.7 pct purity. The tellurium proved difficult to machine because of its brittleness and a technique was developed for casting the tellurium into a graphite slab mold and spark-machining specimens from this slab. Both the copper and tellurium were produced in the form of discs 2 in. diam by approximately 1/4 in. thick with surfaces ground flat to 3/0 emery paper. The diffusion apparatus is shown in Fig. 1. Auni-axial compressive stress was applied to the system through a simple lever system. A stainless-steel rod actuated by the lever arm lay inside a stainless-steel tube. The diffusion couple lay on top of the steel rod, and pressure was applied to the couple between the rod and a plug welded into the center of the tube. To ensure a uniform stress across the couple, a hemispherical boss and cup were used to transmit the load to the diffusion couple. A 400-w tube furnace with a uniform hot zone 3 in. long slid around the stainless-steel tube and maintained the assembly at temperature. A thermocouple situated 3 in. from the specimen operated a proportional temperature controller which maintained the specimen temperature constant to ±2°C. Most diffusion runs were carried out at 250C although a few tests were made at other temperatures in the range 235° to 300°C. The specimens were inserted and removed with the furnace at operating temperature, and took only 2 min to reach diffusion temperature—a time small compared with the total diffusion time. All the diffusion experiments were carried out in a hydrogen atmosphere, since consistent results were obtained in hydrogen and nitrogen atmospheres and in

Jan 1, 1967

By Ken Dyck, Chuck Edwards

"Cameco's McArthur River is the world's largest high grade uranium mine. Production started in late 1999. Cameco carried out the engineering design and construction management for the McArthur River project, including all aspects of mining, ore handling and ore transportation. The ore composition was expected to vary dramatically (0 to 30% U3O8; 0 to 25% clay; etc). To cope with the composition swings, sizing screens were selected to provide classification in the grinding circuit. The grinding circuit started up close to the design to provide minus 500 micron slurry. The 50% solids (wt) ground ore slurry proved to be difficult to transport to and process at the Key Lake Mill. Slurry containing high concentrations of high density pitchblende (about spgr 8.0) and low concentration of stabilizing clays, would settle in containers. Ore transport efficiency to Key Lake was found to be unacceptable.A test classification cyclone was installed in the grinding circuit at McArthur River early in 2002. The cyclone operating parameters were not typical, but the cyclone was made to work very successfully. Transportation efficiency to Key Lake increased due to more stable slurry. Preferentially ground (fine) pitchblende particles were easier to leach at Key Lake. The radiation exposure for operators and maintenance personnel to handle the more stable slurry was also reduced.The classification sizing screens were removed from the McArthur River grinding circuit and replaced by permanent classification cyclones late in 2002.INTRODUCTIONThe McArthur River mine and Key Lake mill operations are located in northern Saskatchewan, approximately 650 and 720 kilometres from Saskatoon, respectively. Figure 1 is a location map. McArthur River is the world's largest, high-grade uranium mine, with a production capacity of 18.7 million pounds U3O8 annually. (Rosner and Edwards 1998, Dyck 2000, Jamrozek 2000, Rodgers 2001) Proven and probable reserves are more than 473 million pounds U3O8. McArthur River ore, grading on average 21% U3O8, is milled at Cameco's Key Lake operation, 80 kilometres southwest by road. McArthur River production began in December 1999."

Jan 1, 2004

Andesites are a major source of aggregate for much of the North Island of New Zealand. There are regional differences with respect to some important properties of the andesites. Some are reactive with cement and are designated as potentially deleterious or deleterious by the concrete industry. Other andesites, particularly those that are slightly altered or weathered, have rather high Plasticity or Clay Indices and perform poorly in road construction. &nbsp; The performance of the andesites has been investigated and can be shown to be determined by: +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; the chemistry of the rock which in turn determines the chemistry of the glass in the rock; +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; the presence of large amounts of groundmass glass in the rock; and +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; the nature of the superimposed alteration processes. Environment of extrusion and how rapidly the rock has been cooled or chilled are also important as they determine the fabric of the rock and how much glass will be present in the rock. &nbsp; There are three main types of alteration that affect the quality of the aggregate: 1. &nbsp; hydrothermal alteration, 2. &nbsp; late magmatic alteration associated with the devitrification of glass, and 3.&nbsp;&nbsp; weathering. &nbsp; Each of these alteration types produces different alteration minerals. In fresh andesites the devitrification of glass has an important affect on the rockÆs properties. The Taranaki andesites are shown to have unusually (in comparison with other North Island andesites) high Na2O contents, held in the groundmass glass, which is the fundamental reason for the high alkali û silica reactivity of these andesites.

Jan 1, 2005

By Nicholas Kyriazi

A joint effort by the U.S. Bureau of Mines (USBM) and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR&apos;s), deployed in accordance with Federal regulations (30 CPR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR&apos;s in the fourth phase of testing from 1989 to 1993. The SCSR&apos;s were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except units with manufacturing defects. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. In addition, some apparatus collected for this study had not been returned to the manufacturer in a recall effort for correction of a manufacturing defect. In both cases, the apparatus would have presented problems in emergency use. Recommendations include improved training in inspection procedures and better enforcement of recall notices.

Jan 1, 2010

By John B. Mitchell

Approximately 90% of all potash produced is employed as a fertilizer, either directly or with nitrogen and phosphorus. The remaining 10% is utilized in the manufacture of other chemical products, The original source of potassium was wood ash (hence the name potash), However, today the term potash refers to all commercially important salts of potassium. Sylvite, usually found associated with halite, is the predominant economic potash mineral; carnallite a lesser important source of potassium chloride, while langbeinite is important as a source of potassium sulphate. The world&apos;s first potash mining operation commenced in Strassfurt, Germany about 1860, Since that time the industry has grown steadily to its present annual volume of about 30, 000, 000 tons of potassium chloride products or 18, 000, 000 tons of K2O equivalent, potassium chloride or "muriate of potash" being equivalent to 63. 1% pure K2O, WORLD POTASH RESERVES ARE NOT EVENLY DISTRIBUTED The earth&apos;s crust contains 2 to 3 per cent potassium, mostly in the form of insoluble silicate minerals. The economically important deposits, however, are formed from brines concentrated by evaporation. The world&apos;s most important commercial deposits are of Devonian and Permian age, however soluble potassium bearing salts are presently being concentrated by evaporation in several drainage basins, notably Searles Lake, California, Great Salt Lake, Utah&apos; and in the Dead Sea. At least twenty-four countries are known to have reserves of potash: Canada and the USSR have over 80% of the presently known world reserves, (Figure 1)

Jan 1, 1972

By S. Yalcin, S. Chang, M. Oliazadeh

"Present day ferrochrome demand is on the rise, as more steel products require this material as an alloying element. It is projected that the stainless steel demands will grow by about 6% per year to 2020; as such, the supply and demand for ferrochrome appears promising. Chromite is the only economical source of chromium, which is commonly upgraded by gravity techniques and used to produce ferrochrome. The gravity separation methods are not able to treat particles finer than 0.1 mm efficiently. Therefore, in processing chromite ore, a large quantity of fine tailings; some 25% of the mineral values have been reported as lost in slimes during processing. The chromite content of these tailings is typically 10-20% Cr2O3 and accumulates into a large stockpile/pond. A chromite concentrator project in Canada, considers a cut-off grade of 20% Cr2O3. This indicates further processing might be required to recover chromite from low-grade stockpile when the high-grade deposits are depleted. Low-grade ores normally indicates disseminated chromite ores with low liberation and consequently fine comminution. This paper reviews the techniques for treating chromite from fine material and provides some examples of successful operations in fine chromite recovery. Beneficiation techniques for fine particles include gravity separation, magnetic separation, and flotation. Several case studies are presented here that used one of the aforementioned methods or a combination of them.INTRODUCTIONChromium is one of the essential element and important material for production of ferrochrome alloys and special steel. Chromium occurs as chromium spinel, a complex mineral with chemical composition of (Fe, Mg) O (Cr, Al, Fe)2 . Chromite ore is exclusively found in ultramafic igneous rocks. Major associated gangue minerals are talc, quartz, serpentine and iron oxides.Chromite is a heavy mineral, with a specific gravity in the range of 4-5, relative to associated gangue minerals in a chromite ore, which makes gravity concentration a suitable process. This is generally true for coarse particles, ranging from 1 mm to 100 mm. Typically, the ore is prepared by crushing (and grinding if necessary) to a suitable size and the material is sized for the appropriate beneficiation techniques. It is common to use heavy medium separation (e.g. dense media drums, dense media cyclones, or Dyna Whirlpool) to treat coarse size and intermediate size particles (1 – 100 mm). Intermediate and fine particles (20 – 0.1 mm) could be treated by jigs. Spirals, shaking table, sluices, and Reichert cones can upgrade fine particles. Figure 1 shows a typical chromite beneficiation process flowsheet. As can be seen, it consists of three major sections: feed preparation (crushing, screening), de-sliming, and concentration. Beneficiation recoveries range from 80 to 85%, although the ratio of upgrading is only 2 to 3."

Jan 1, 2013

By N. du Preez, J. Christie, F. Crundwell

Precipitation is a key process in the recovery of copper and cobalt. While there is a wealth of experience in operating precipitation steps, improving their performance remains challenging. Chemically, the reaction might be controlled by reaction kinetics, be limited by oxygen mass transfer, or be at equilibrium. In this paper, we examine these different operating regimes and demonstrate how they can be identified from plant operating data, process modelling, and pilot plant test work

Jan 1, 2023