Search Documents

By A. Majumdar, B. Servière, H. Persson

The CCR refinery, which was built in 1931, treats both internal and third party copper anodes to produce 325,000 mt of copper as cathodes. These anodes contain high levels of impurities, such as Ni, As, Sb and Bi, that reports to the electrolyte during the refining step and need to be removed in order to maintain cathode quality and operating efficiencies. In the purification plant, the electrolyte is de-copperized via electrowinning in three stages. In the last stage, the copper content of the electrolyte is reduced to below 1 gpl in order to maximize the co-deposition of As, Sb and Bi with the Cu. This is accomplished with minimum arsine gas generation by using periodic reversal of the current and by controlling the final copper content of the electrolyte. Nevertheless, the possibility of exposure to arsine is treated as a major risk and controls have been implemented to reduce this risk. This paper describes the controls in place at the purification plant, which are being continuously improved through periodic risk assessments and audits. INTRODUCTION The CCR Refinery, which is a part of Glencore Canada Corporation and located in Montreal-East, Quebec, is a custom copper and precious metal refinery, with a capacity to refine 325,000 tonnes of copper anodes per year. Copper anodes are received from the Horne smelter in Rouyn-Noranda, Quebec, Altonorte smelter in Chile and other 3rd party smelters. CCR anodes are produced using the spent anodes from the tankhouse along with purchased spent anodes and copper scrap. The precious metal plant treats the tankhouse anode slime, purchased anode slime, precious metal ingots and Doré anodes from Glencore’s Brunswick lead smelter in Belledune, New Brunswick. CCR products include copper cathodes, silver and gold bullion, a platinum-palladium concentrate, selenium, tellurium dioxide and nickel sulfate. In 1975 an accident occurred at CCR where two employees were exposed to fatal levels of arsine emitted from the then existing purification cells. This process was therefore shut down immediately. Research and development work was then initiated to determine the optimum electrowinning conditions whereby arsine gas generation would be minimized while maintaining high copper and impurity removal efficiencies. It was found that the application of periodic reversal of current (PRC) during the last stage of electrowinning retarded the onset of arsine formation while at the same time allowing the copper concentration to be reduced to less than 1 gpl (Houlachi & Claessens, 1978). A new purification plant was designed based on the PRC technology and was started up in 1976. In addition to the use of PRC electrowinning, the new plant is located in a fully enclosed section of the tankhouse. A special effort was made to design a ventilation system to evacuate the acid mist in addition to any arsine gas. Arsine monitors were installed to measure the emissions from the stack along with arsine levels in the workroom. The arsine monitors and the ventilation system were interlocked with the rectifiers (Thiriar et al., 1983).

Jan 1, 2019

By T. Guan, G. Fu, X. Zhou, L. Deng

"Currently, tailings water is required to be recycled in minerals processing plants. When the flotation tailings water of complex copper-sulfur-tungsten polymetallic ore is reused to the flotation of copper-sulfur ore, a portion of tungsten would be lost in copper concentrate or sulfur concentrate due to the addition of the collectors used for oxidized ore which are also effective for the sulfide minerals in the process of tungsten flotation. At the same time, the technical index of copper concentrate and sulfur concentrate would be seriously affected by tailings water. Our experimental researches of many years show that the copper concentrate with a grade of 18.36% Cu at a recovery of 76.67% is obtained for the raw ore containing 0.60% Cu, 18.99% S, 0.16% WO3 in small locked cycle test using recycled water, through simple pretreatment of the tailings water from tungsten flotation and adding special regulator CW and new tungsten collector TM. The result is close to the performance without using tailings water. And, in the continuous pilot experiment which was continuously conducted for 4 days with the same technology, the following results was obtained: the copper concentrate with a grade of 21.74% Cu, the recovery was 71.55%; the sulfur concentrate with a grade of 45.16% S, the recovery was 80.10%; the tungsten concentrate with a grade of 42.63% WO3, the recovery was 54.62% relative to raw ore (the recovery relative to scheelite was 76.47%). The throughput of the continuous pilot experiment is 1.0~1.2 t/d, and the raw ore contains 0.56% Cu, 18.80% S, 0.14% WO3 on average.INTRODUCTIONMining industry is one of the most important developing fields, it supplies raw materials for industrial production as well as discharges much waste water. Tailings water is the main source of beneficiation waste water, it would result in severe environmental pollution if discharged directly. Generally, the tailings water would bring undesirable effect on flotation index after simple pretreatment by lime (Kalin, Fyson, & Wheeler, 2006). On the other hand, the treatment of tailings water through ion-exchange (Cui & Liu, 2015) before recycling is of high cost. Generally, in the flotation of Cu-S-W polymetallic ore, when the tailings water from tungsten flotation is treated simply by lime and recycled to the flotation of sulfide minerals, the flotation index of sulfide minerals decreases, and a portion of oxide mineral would be lost in the sulfide concentrate. As a result, the recycle rate of this kind of tailings water is relatively low, some of the tailings water is discharged after simple treatment and then environmental pollution is caused subsequently. One of the effective ways to improve beneficiation performance and increase the recycle rate of tailings water is to conduct research on developing recycle technology for flotation tailings water of complex copper-sulfur-tungsten polymetallic ore."

Jan 1, 2016

"Chairman: Professor J. C. Griffiths Rapporteur: Mr J. P. G. PRETORIUSPapers:Mine-mill production scheduling by dynamic programming by R. J. Roman Optimization of a large mining venture by J. C. Paynter, B. K. Loveday and C. G. Robinson Economic surface mining of multiple seams by T. V. Falkie and W. E. PorterIn introducing his paper, Mr Roman said that whereas in manufacturing plants the yearly production levels were usually chosen to produce the largest annual cash flow, in a mining operation, the raw materials (ore) were exhaustible so that the production had to be scheduled to maximize the total net present worth of the operation. This optimum production schedule could be determined by using dynamic programming. The required information was readily available to management at most mines. The 'possible operating range' of production rates lay between the rate with the highest profit per ton. and that with the highest profit per year. The optimum production rate started typically at the top of this range and decreased slowly as the deposit was depleted.Dynamic programming was used to determine several production schedules for a hypothetical mine-mill complex. The effects of changes in the ore grade estimates, size of deposit and acceptable rate of interest on the production schedule were taken into account. Apart from the fact that the net present worth of the overall profits was larger than that obtained by conventional methods, it appeared from the cases studied that the amount of metal recovered was also greater.Dr it P. King commented that this was a very interesting application of dynamic programming. He pointed out, however, that the market price of the metal was likely to vary significantly and randomly during the life of the mine, and he suggested that the problem should, therefore, be reformulated as a stochastic dynamic programming problem.If the price of the metal rose to abnormally high levels, a much higher than normal production rate could be expected. The results of analyses given in Table 5 showed that the production rate was a function of market price. In his view the stochastic problem could be solved just as easily as the deterministic problem.In reply to a question by Dr King as to whether the function relating recovery to production rate (Table I) was based on real data, the author replied that it was based on the results of an analysis conducted at the Union Carbide Corporation's Pine Creek tungsten mine in California.Dr D. M. Hawkins stated that costs were incurred when the production rate was altered, for example, in appointing or laying off staff, and that in practice it may be necessary to take these costs into account in finding the optimum production rate. Mr Roman replied that, while normal administrative costs were accounted for, the additional costs incurred in appointing and laying off staff were not taken into account."

Jan 1, 2014

By M. A. Stogran-Baker, S. Cole

"Fluorspar mining occurred in the St. Lawrence area from the 1930s until the mid 1980s. In 2013, CFI discovered a new ore body, the AGS vein, which proved amenable to more economic open pit mining methods. A new mill was designed to produce 200,000 tonnes per year of high quality, acid-grade fluorspar concentrate. The simple mill flowsheet includes crushing, dense medium separation (DMS), grinding, sulphide flotation, pulp thickening, fluorite flotation, thickening, and concentrate filtration. The type of flotation cell used is being installed for the first time in North America. Site clearing commenced in the spring of 2016, followed by mill building erection completed by the fall of the same year. Civil and mechanical installation as well as site-wide construction was completed by the end of September 2017. Commissioning commenced, and at the time of paper submission mill production is on track to ramp up to full capacity by the beginning of 2018. This paper will focus on the use of fluorine NMR analysis applied to fluorite and the development of on-stream analysis, flotation cell selection and the decision to install the new cells, and the water control program designed to maintain process control with the least possible environmental impact.HISTORY St. Lawrence is located on the south-eastern coast of the Burin Peninsula in Newfoundland and Labrador. The first occurrence of fluorspar in the St. Lawrence area was recorded in 1843 by British geologist J.B. Jukes (DNR 2010). Fluorspar was likely extracted in small quantities prior, however commercial fluorspar mining did not commence until 1933 at the Black Duck Mine. The Black Duck Mine operation processed ore by washing and screening – acid-grade was hand-picked from the oversize, the undersize was sold as a lower grade product. The Black Duck Mine was closed in 1941 (Wilson 2010). The American Fluorspar Limited (New Fluor) commenced operations on the Director vein in 1936, and was bought by Alcan in 1942 (Cooper 2012). Alcan also developed the Iron Springs as well as the Tarefare deposits. The Black Duck Mine mill had closed, and a new mill was built. This new mill crushed the ore prior to dense medium separation, the sinks of which were sent to Quebec for use in Alcan’s aluminum smelter (CFI 2016). Alcan shut down it’s mining operations in 1977 due to the dropping price of fluorspar as well as labour disputes. In 1986, the British-based Minworth Limited began producing ore from underground at Blue Beach North and Blue Beach South, as well as from open pits at Tarefare and Director veins (Cooper 2012). A new mill was built by Minworth in order to process the ore using flotation to produce an acid-grade concentrate. The low price of fluorspar caused Minworth to shut down operations in 1990. Whilst exploration has been ongoing, no mining had occurred in the area since 1990."

Jan 1, 2018

By Min Chen, Zhen Tian, Hongxu Cui

"The effects of adjusting technology on the phosphorous enrichment in converter slag were investigated. The results showed that the grain size of 2CaO·SiO2 with high phosphorus containing content increased slightly with the decreasing of cooling rate, and the proper cooling rate was confirmed to be about l.0°C.min-1. Moreover, the morphology of the phosphorus-rich phase of 2CaO·SiO2-3CaO·P2O 5 was changed from granular for the higher basicity of converter slag to the coexistence of granular shape and rod-like for the lower basicity of adjusted slag. With the addition of adjusting agent such as SiO2 to lower the basicity of converter slag, the phosphorus in converter slag could be transferred into 2CaO·Si02 phase effectively, and P2O 5 content in high phosphorus containing phase reached to above 30%.IntroductionThe yield of converter slag is very large in China, but most of the slag is stacked usually after the separation of iron, which not only takes up a lot of land, but also affects the ecological environment seriously. Therefore, improving the comprehensive utilization and value-added products of converter slag is of great significance to recycle the steelmaking slag[l-3]. On the other hand, the refining of hot metal with high phosphorous content is an unavoidable problem with the decreasing of high grade iron ore, and as a result, more amounts of high phosphorus containing steelmaking slag are produced. However, the current recycle of converter slag is more focused on the emission reduction and reuse of steelmaking slag inside the iron and steelmaking process without considering the recycle of phosphorous resources[4-6]. At the same time, the development and utilization of phosphate ore as a strategic resource is drawing more and more attention, but the phosphate ore in China is mostly low grade and significant amounts of tailings are produced which is harmful to the environment. Therefore, it is important to separate phosphorous resources in steelmaking slag which can be used as phosphate ore for fertilizer material[7-9].Literature studies showed that most of the phosphorus in steelmaking slag existing as 2CaO·SiO2-3CaO·P2O 5 solid solution phase in 2CaO·SiO2 particle. The P2O 5 content in the phosphorus containing phase is very low due to the fact that the basicity of converter slag is usually high and the precipitated amounts of 2CaO·SiO2 particles during cooling are very large, resulting in the fact that the P2O 5 contents in 2CaO·SiO2-3CaO·P2O 5 solid solution phase are much lower which is impossible to be used as phosphorous resources instead of phosphate ore. Thus, the enrichment of phosphorus in steelmaking slag is need[ 10-14]."

Jan 1, 2011

By P. G. Hallof

Only recently has the term Induced Polarization found its way into geophysical literature. Schlumberger first mentioned the possible use of the induced polarization effect in one of his early papers. Later, induced polarization was the subject of several university theses, such as Seigel's at the University of Toronto and Bliel's at the Michigan School of Technology. In addition, a group at the New Mexico School of Mining and Technobgy has done work on induced polarization. There is very little to be found in print on the subject of induced polarization. Several papers have been presented at meetings, the 1958 AIME and SEG* conventions, for instance, on laboratory measurements of the effect and theoretical considerations useful in the interpretation of field results. This paper is the first attempt to present actual field results which show the usefulness of induced polarization as a prospecting technique. There are several phenomena that can cause polarization when electrical current is passed through the ground. In a paper presented at the 1958 SEG* meetings Professor T. R. Madden of M. I. T. demonstrated that only two of these gave rise to appreciable effects. The first is a result of the membrane and diffusion effects in a sandstone that contains appre- ciable amounts of clay minerals. The unbonded charges associated with the clay mineral forma material that passes positive and negative ions with different mobilities. When current is passed through such a system for some period of time, polarization results. The second phenomenon, which gives rise to very much larger polarization effects, is the one used in the new prospecting technique. These effects are a result of the blocking action or polarization of metallic or electronic conductors in a medium of ionic solution conduction. This electrochemical polarization, called "the over-voltage effect" by electro-chemists, occurs whenever electrical current is passed through a volume of rock which contains metallic minerals such as base metal sulphides. This polarization at metallic interfaces in ionic solutions depends upon the chemical energies necessary to allow the ions to continue the flow of current by giving up or receiving an electron from the metallic surfaces. The energy stored in this reaction isanalogous to that stored when a condenser is charged. If a d. c. current flowing through such a system is interrupted, the polarization can be detected as a small, decaying current that flows after the applied current is discontinued. The decaying potential measured is a result of the current flow caused by charges returning to their equilibrium positions from the positions they assumed under the applied potential field. Because of the polarization, there is an excess of change at each metallic interface. There is an alternate method of measurement of the induced polarization effect. The electrical

Jan 1, 1961

By C. S. Parsons

Introduction Up to the present, the operation of small mills for the treatment of gold ores has not been favoured in Canada to the extent that it has in other countries. For instance, a list of the operating properties in Southern Rhodesia, published in The Rhodesian Mining Journal of November, 1934, shows for the month of September, 1934, that there were over 500 small mills treating less than 50 tons per day, and the majority of these between 5 and 25 tons. They are operated by individuals, syndicates, and small mining companies. It is presumed that the operations are profitable, although from the published figures of the tonnages treated and the yields, it is difficult for one familiar with Canadian operations to understand how this can be possible, in the majority of cases. Most of these small mills employ stamps with plate amalgamation and with, occasionally, tables to produce a concentrate. Enquiries have been received from many parts of the world respecting milling practice suitable for small gold mines and the type of plant used in Canada. The tenor of these enquiries leaves the impression that the majority of the writers assume that the practice would be similar at all small properties. This, of course, is not the case. Conditions vary widely, and what would be a suitable mill for a typical Nova Scotia ore would not necessarily be wholly adaptable to many ores in Ontario, Quebec, or British Columbia. This paper has been written with the intention of inviting discussion, and it is hoped that, by such discussion, the subject will be more fully dealt with than has been possible in the time at the disposal of the writer. Only more or less standard principles and practices have been dealt with, and, purposely, no reference has been made to plants using mills of the Hadsel, the Nutt, or the Gibson type. As there is available but little reliable information on the costs of installation and operation of small mills, it is also hoped that those contributing to the discussion of milling practices for small mines will be in a position to give these data for the benefit of those contemplating the erection of small plants in Canada. Although it is difficult to generalize, it can be said that there are three types of gold mills commonly used at small mines: (1) Amalgamation and Gravity Concentration; (2) Amalgamation and Flotation; and (3) Cyanidation.

Jan 1, 1935

By W. R. McClelland

GOLD-BEARING ores, representing many types, are found widely distributed through the Province of British Columbia. They range from those which by their nature may be considered as complex, to those whose mineral characteristics are simple. Those in which the gold is associated with metallic sulphides provide particular milling and metallurgical problems, the solution of which involves not only detailed laboratory investigation but also a careful consideration of economic factors. The location of an ore-body may have a deciding influence on the adoption of a method for the metallurgical treatment. Whether the ore should be treated with the object of recovering the gold as bullion or as a shipping concentrate is often dependent on such topographical considerations as the position of the mine at or near tidewater or within a reasonable overland distance of a smelter. British Columbia is fortunate in having the Trail smelter situated in the southern part of the Province, and the smelter at Tacoma, Washington, is accessible for coastwise traffic. Both of these provide a ready market for most types of gold-bearing concentrate. In order that the results obtained by laboratory tests may give a fair indication of what should follow in mill operation, it is essential that the test sample should represent as closely as possible in mineralogical character and in grade the ore that eventually will constitute the feed to the mill. In the early stages of mine development this consideration is sometimes overlooked and samples of a much higher grade than would be representative of run-of-mine ore are submitted. Flotation tests on such a sample of ore high in sulphides may show a low ratio of concentration, bu.t if the actual run-of-mine ore is lower in sulphides the mill operation will reveal a much higher ratio. The recommendations for treatment based on the results of laboratory tests may have been against concentration, when in actual operation this would be the most suitable method of treatment. Recommendations based on laboratory tests are necessarily from the results of work carried out on the sample submitted, modified only by such other economic or topographical information as may be known to the investigator. This paper deals with a few of the gold ores found in the six mining districts of British Columbia and is based on investigations made in the Ore Dressing and Metallurgical Laboratories of the Mines Branch, Department of Mines, Ottawa.

Jan 1, 1937

By Jinxing Ji

Several fundamental aspects related to the nickel electrowinning from chloride electrolytes have been addressed in this paper. The thermodynamic study includes the activity coefficient of the hydrogen ion and the speciation diagram of NiCI2 solutions. The activity coefficient of the hydrogen ion (YH+) was calculated and estimated experimentally using a combination glass pH electrode. It was found that YH+ was greater than one in concentrated NiCl2 solutions and increased significantly with increasing NiCl2 concentration. The speciation diagram for NiCl2 solutions was plotted with YH+ and the effect of the ionic strength on the equilibrium constants being taken into account. It was discovered that the predominant nickel species in the acidic region were Ni2+ and NiCI+ in 0.937 M NiCl2 solution at 25°C. Electrodeposition tests demonstrated that higher Nit' concentration in the electrolyte improved the current efficiency of nickel electrodeposition (CENi). The additions of H3BO3, and NH4Cl increased very little the current efficiency of nickel electrodeposition at pH 1.5 and temperature 60°C. However, the addition of sulfate decreased the current efficiency of nickel electrodeposition. Nickel electrodeposition was also found to be a steady-state process since the amount of acid added to the electrolyte at a constant pH increased linearly with time during galvanostatic electrodeposition. The cathode surface pH during nickel electrodeposition was measured using a flat-bottom combination glass pH electrode and a 500-mesh gold gauze as cathode. The cathode surface pH was found always to be higher than the pH in the bulk electrolyte, and if the current density was sufficiently large, it would eventually reach a level causing precipitation of insoluble Ni(OH)2(s) on the cathode surface. Rotating disc electrode studies revealed that the rate of nickel electrodeposition was first order with respect to the activity of nickel ion and zero order with respect to the activities of chloride and hydrogen ions. The rate of hydrogen evolution was found to be first order with respect to the activity of hydrogen ion and to be zero order with respect to the activities of nickel and chloride ions. These findings indicate that nickel deposition and hydrogen evolution proceed independently.

Jan 1, 1995

By Jeff Starchuck, Harald Kullmann

"In 2005, an inspection showed that the Deception Bay Wharf in the Canadian Arctic was at the end of its service life. Although Deception Bay is closed with landfast ice up to 5 ft thick, shipping operations continue year-round, with additional voyages in the summer open-water season to supplement mine supplies. The rehabilitation scheme that allowed minimal interruptions to shipping involved concrete caissons cast on barges and an ingenious placing system.WorleyParsons Westmar of Vancouver, B.C., performed the inspection under contract to the owner, Xstrata Nickel, Montreal, Quebec. The wharf, on the coast of the Nunavik region of Quebec, was originally constructed in 1971 for an asbestos mine, and is now used to support Xstrata’s Raglan nickel mine, importing fuel for p o w e r g e n e r a t i o n a n d general mine supplies, and exporting nickel concentrate to smelters in the south. Emergency repairs were essential to allow operations to continue at the site, while the parties considered permanent rehabilitation options and secured funding. The repairs were done in the openwater seasons, and included reinforcing the failed interlocks above water level with steel patch plates and injection grouting of the cell fill below the port crane in 2005. In 2006, workers installed a circumferential belting system below water level.Westmar held critical planning sessions with the mine operation personnel to find ways to stretch the limits of the mine supplies and nickel storage facilities. In the end, the parties agreed to shut down construction activities four times during the ice-free season to allow access to the dock site.Westmar developed a plan that allowed mine operations to continue during construction, and Xstrata approved the plan and budget in September 2006, for execution in 2007. Rapid construction was essential. To accommodate the short construction season and maintain minimum levels of service for the mine, the work was radically different from conventional Arctic deep-sea port construction. Like the original Deception Bay Wharf, construction practice was to use steel sheet pile circular cells with the consequential heavy support services for the labour force. Construction duration was typically two seasons. The plan for Deception Bay was executable in one season based on a concrete caisson structure. Only a modest amount of schedule float was needed."

Jan 1, 2009

By J. Postle, Deborah McCombe

"This is the third in a series of articles about the Committee for Mineral Reserves International Reporting Standards (CRIRSCO). The first article was an interview with Niall Weatherstone, Chairman of CRIRSCO (CIM Magazine, February 2008) the second described the background and goals of CRIRSCO (CIM Magazine, March/April 2008). In 2007, CRIRSCO was adopted as the Reserves and Resources Task Force of the International Council on Mining and Metals. This decision by ICMM has resulted in an increased level of funding for CRIRSCO and the ability to advance its objectives. In mid-October 2007, CRIRSCO members met in London England to discuss the status of each of the member countries’ reporting codes and the progress of various CRIRSCO projects. Update on national reporting codes Australia: The last update of the Australian JORC Code was in 2004. While there are ongoing discussions about issues that arise from the application of the latest version of the Code, there are no plans to update JORC in the near future. Canada: The Canadian Securities Administrators revised National Instrument 43-101 in December 2005. At the same time, the Canadian Institute of Mining, Metallurgy and Petroleum published updated Resource and Reserve Definitions that are incorporated by reference in NI 43-101. CIM is continuing work on developing Best Practice Guidelines to assist practitioners in the estimation of Mineral Resources and Reserves. South Africa: The South African Mineral Reserve Committee is currently awaiting an update of the Johannesburg Stock Exchange Limited Listing Rules, which will incorporate both SAMREC and SAMVAL (South African valuation guidelines). The official launch of both codes is expected in 2008. Europe: The Pan-European Reserves Reporting Committee expects to release a consultation draft in 2008. Emphasis is being placed on industrial minerals and aggregates, which constitute a very large industry in Europe. Chile: The Chilean Certification Code was approved in early 2008. As part of the Code, a National Commission is being established to screen and review reports on a random or specific basis. United States: The Society of Mining Engineers updated the SME Reporting Guidelines in 2007. The Securities and Exchange Commission has not accepted these more up-to-date definitions and guidelines. The SME committee will continue to discuss the incorporation of these Reporting Guidelines with SEC. SME has also established a class of membership, a Registered Member, which includes disciplinary measures for non-compliance with the SME guidelines."

Jan 1, 2003

By C. Dirscherl

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications. KEYWORDS: Gearless Mill Drives, Gearless Conveyor Drives, Availability, SAG Mill, Ball Mill, Overland Conveyor, Antapaccay INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump…) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch…), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment) Intermediate gearboxes are not required when a motor is used with a rated speed that directly matches the speed requirement of the driven equipment. Furthermore the VSD can be used to smoothly start the motor and to vary speed during operation, which means that it satisfies both requirements."

Jan 1, 2015

By C. Matthews, A. Vo

"Australia is one of the world’s leading exporters of bulk commodities and the extensive use of sampling equipment is key to the successful management of each mining operation. At the process plant, without a full understanding of the feed, product and tails, it is impossible to fully optimise the performance of the plant, such that the metallurgical balance is often open to error. At the port, a statistically correct, bias free and compliant sampling system is crucial to ensuring exported minerals are reflective of their true value and to avoid penalties. Over the last decade, as a result of the iron ore boom, there has been high demand for reliable, representative and standard compliant solids sample systems in Australia. This paper reviews several solids sampling applications at Australian mine sites, the challenges and experience gained and how the implementation of reliable representative sampling systems has provided better understanding of plant process performance, improved plant control and overall benefits to the operations.INTRODUCTION Mining is the primary contributor to the Australian economy with Australia ranking in the top 4 in economic resources for 21 primary industrial minerals in 2016 (Britt, et al., 2017). Australia is one of the world leaders in the export of the majority of its commodities including gold, copper and iron ore (Britt, et al., 2017). Therefore, a suitable and standard compliant sampling system is essential for evaluating plant performance and content verification. At the mine and at the port, the larger iron ore miners in Australia have developed stockpile models to predict the grade of their ore down to individual blocks of the stockpile. This allows the miner to create the right blend of material for sale to their customers and ensures they are not underselling their product or at risk of penalties for impurities or low grade. As an example, the average difference between the benchmark 62% Fe and low grade 58% Fe fines at the time of this report averaged US $30/tonne according to the Metal Bulletin Iron Ore Index. At a shipload of 180kt this would be a variation of US $5.4M. Whilst this is an extreme example, it highlights the economic importance of producing the correct grade product and a recognised representative sample of said product."

Jan 1, 2019

By J. -M. Lalancette, D. Lemieux, C. Chouinard

"A gold bearing concentrate containing 107 g/T of gold, 9.3% copper and 706 ppm of mercury was processed at the demonstration scale for the extraction of gold and copper using a cyanide free process. The concentrate was generated through flotation to upgrade the gold and copper grade, but also showed contamination with mercury. This concentrate was submitted to the DST process demonstration plant. The concentrate was first oxidized using a fluidized bed to produce a calcine. The mercury was volatilized during the oxidation stage with an efficiency higher than 98%. The mercury was condensed and removed from the sulfuric acid using a thiosulphate process. Copper was extracted from the calcine as copper sulphate using diluted sulfuric acid. The solid remaining after acid leaching was submitted to the DST chlorination process for gold extraction. Under optimized conditions, a gold extraction of 97.3% was achieved in the chlorination reactor. Gold was recovered from the pregnant brine by precipitation on silica using a DST proprietary process.INTRODUCTION Dundee Sustainable Technologies Inc. (DST) offers proprietary metallurgical processes for the treatment of material from the mining industry. DST processes enable the extraction of precious metals and for the removal and stabilization of contaminants, such as arsenic, from ores and concentrates. DST provides environmentally-friendly, viable and efficient processes, capable of handling complex and refractory ores which cannot be processed with conventional approaches due to metallurgical issues or environmental considerations. Several mining jurisdictions around the world have banned or restricted the use of cyanide. DST has developed a closed loop chlorination process as an alternative to the conventional cyanidation process for the extraction of precious metals from minerals. The tailings from the process are inert from toxic substances such as cyanide and organic compounds, are sulphide depleted which means they do not generate acid, and thus, meet and/or exceed environmental norms. The process has demonstrated excellent gold recoveries within a fraction of the time needed for cyanidation to obtain similar results. Moreover, the closed loop process does not generate any liquid effluent and does not consume much water: it only requires a water make-up to compensate for moisture leaving with the tailings and by-products, and seawater may be used. The improved environmental footprint of the DST process has been certified by the Environment Technology Validation program (ETV) which provides an independent evaluation of the performance claims of innovative technologies."

Jan 1, 2017

By Roger Favreau, Patrice Favreau

Without blasting there can be no roads, no hospitals, no factories, not even foundations for homes. Yet in 1960 the only way to design a blast was by trial/error. By comparison, bridges were already designed by calculations before being actually built. This was possible because equations based on the fundamental principles of science existed with which all the stresses in the bridge could be calculated. In 1960 no equations based on the fundamental principles of science existed with which the mechanisms that take place inside the rock mass during a blast could be calculated. Since then the main author made it the objective of his research to seek such equations, and to validate that they gave accurate answers by means of experiments in the field, experiments made in co-operation with mines, quarries and the explosives industry; results have been reported in some 90 publications.These equations now deal with essentially all aspects of a bench blast: the intensity of the shock wave and the fragmentation size distribution throughout the rock mass; the movement of all the fragments into the muck pile; the fly rock and vibrations from the blast; etc.; are presented examples of such equations. They are now assembled into a computer simulator called Blaspa accessible on the Web, with which one can design a blast just as a bridge is designed. An example is presented. The reason to design a blast by simulations rather than solely by trial/error is that if it leads to damage, it is only after the actual blast that the blast design is realized to cause damage. If however the blast design had been simulated before the blast, then the risk of damage is identified before the blast and is prevented by redesigning the blast. Examples of such situations are presented. The need to a void damage is very necessary because the public is becoming opposed to blasting. When a blast does cause damage, and people learn that the blast was designed solely by trial/error even though simulation was available and would have prevented damage, they become even more strongly against blasting; they may succeed in getting a quarry closed. Their objections to unchecked blasting are not unreasonable, especially as simulating a blast with Blaspa on the Web is a very simple procedure.

Jan 1, 2013

The Pilbara region, located in the north-west of Western Australia, is significant as the second-largest source of iron ore on the planet. Iron ore mines owned and operated by Pilbara Iron are located within the Hamersley Basin. This paper refers to the Greater Paraburdoo mines, the 4WEST and 4EAST pits, located on the southern margin of the Hamersley Basin. The groundwater model refers to ephemeral watercourses: Seven Mile and Pirraburdoo creeks, which are adjacent to the two pits, and Ratty Springs, located upstream from 4WEST and within Pirraburdoo creek. The spring and creeks hold cultural heritage significance for local Aboriginal communities. Two of these, the Gobawarrah Minduarra Yinhawanga (GMY) and Innawonga native title claim groups, initiated hydrological work on the two creeks and Ratty Springs, with the aim of determining the affects of dewatering on the natural water flows of these systems. The numerical model used to simulate drawdown in the Pirraburdoo and Seven Mile Creeks was derived from PMWIN Pro software and covered an area of 77 km2. The modelling period was from January 1998 to December 2004, and the prediction period was from January 2005 to December 2015. The model has four layers and incorporated effects caused by mining voids, 4WEST and 4EAST pits, creek bed material, weathered bedrock below creeks and surrounding banded iron formations (BIF). The model has been calibrated using the trial-and-error method set down by Middelmis et al (2001). The current dewatering schedule (12 ML/day) in the 4WEST and 4EAST mining areas does not affect the water table levels in the adjacent creeks significantly or for any considerable periods of time. However, changes to mine plans may occur, for example, in response to changed commodity price and may lead to significant increase in rates of vertical advancement. This, in turn, affects dewatering schedules, as greater vertical advancement requires increased dewatering effort. When an accelerated mine plan is applied to the model and dewatering rates increased to 18 ML/day, drawdowns in the creeks are more noticeable. The model has therefore helped to indicate the extent to which increased dewatering rates may be acceptable, especially in terms of immediate and longer-term damage to riparian species, ie Melaleuca and Eucalypt. Predictions from the model may also allow mine planners to schedule decreased rates of vertical advancement, where these are required to meet environmental constraints.

Jan 1, 2006

By William C. Browning

An economic drilling programme is one which costs the !east in chemicals, equipment, and time. The basis for such a programme with rotary drilling techniques is a drilling fluid in which bentonites do not swell. This is recognized in the growing trend toward gyp and other inhibited mud systems. Therefore, even though the mechanism of thinner action is a subject of applied colloid ,chemistry, the understanding of this mechanism is of economic importance in controlling the flow properties of inhibited muds. In phosphate, or sodium tannate, conditioned muds that are relative-!y free of contaminating-electrolytes, the thinner, or dispersing agent, is adsor.bed, ?creating an electrical double layer about the clay particles. The mutual repulsion of these charged particles effects colloidal stabilization, or deflocculation of the suspended clays, as discussed by Norton and others. In inhibited muds, however, the electrolyte concentration in the filtrate is sufficient to collapse the double layer and flocculation of the mud solids occurs, as evidenced by increased viscosity and gel values. Chemicals to control the flow properties of inhibited muds, therefore, are vital to the successful use of these systems as it is not always economical to adjust flow properties by watering back. Flocculation of suspended particles, as indicated in the work of Vervey, Overbeek, and others, is due primarily to gravity-like, long-range Van der Waals forces. Prevention of flocculation may, therefore, be secured by the interposition of any barrier between the particles, the thickness of which approximates the extension of the Van der Waals at-traction. Organic polyelectrolytes, such as Kembreak, Rayf!o, and Q-Broxin, may act to increase the double layer charge when used in small amounts in fresh-water muds. More important, however, is the fact that in inhibited muds an increase in concentration of the polyelecholyte permits the formation of a condensed film adsorption layer of the polyelectrolyte about the clay particle. When this occurs, the extremely viscous condensed adsorption layer creates a mechanical. barrier that prevents flocculation of clays, even in the presence of inhibiting concentrations of elecholytes. Rheological evaluation of the degree of deflocculation, or colloidal stability, may be made by utilizing the known effects of particle inter-action and volume concentration on the flow properties of suspensions. Rheological evaluation should be supplemented by direct microscopic or ultra-microscopic observation.

Jan 1, 1958

By B. H. Cody

The Morenci concentrator of the Phelps Dodge Corporation is a part of the project that was completed after five years had been spent in development of the open-pit mine, equipment and process testing in the former No. 6 concentrator, and construction of the reduction works. The reduction works, of which the concentrator is a part, is about a mile and a quarter southeast of Morenci, on the highway that leads up Morenci Canyon. The concentrator has a nominal capacity for the treatment of 45,000 tons of ore daily. The original plant, which has a rated capacity of 25,000 tons of ore daily and is now in its fifth year of operation, began production on Jan. 30, 1942. The addition, to increase the capacity 80 pct, began operation on Dec. I, 1943. The equipment of the original plant has been described in Mining and Metallurgy (May 1942). NO changes in equipment were recommended for installation in the concentrator extension and only one major change, forced by a shortage of maintenance labor, has since been made. Metallurgical treatment has been altered in some ways as experiments progressed and as labor and economic conditions dictated. No complete description of the operation of the concentrator has been published, so this paper will record such operating and equipment changes as have been necessary, the operating methods that have been developed and the metallurgical results that have been obtained. Descriptions are given in the order of the processes with a flowsheet and an equipment list of each process for convenient reference. The questions asked by engineer visitors have guided the detail in which operation and maintenance are described. During the period Jan. 30, 1942 to Sept. I, 1946, ore milled has totaled 43,595,253 dry tons, from which 1,643,885 tons of concentrate have been made, containing an indicated production of 783,164,-809 lb of copper. The principal results obtained in operation of the concentrator during the years 1942 to 1945, inclusive, and to Sept. I, 1946 are shown in Table I. A graphic general flowsheet of the plant is given in Fig I. Ore The Morenci ore that is now being treated is a medium-hard monzonite porphyry in which the principal sulphide minerals are chalcocite and pyrite. A minor amount of covellite is present. Chalcopyrite and bornite have been observed under the microscope. The chalcocite occurs mainly as a coating on pyrite. Some of the coatings are so thick that the pyrite presents the appearance of being an inclusion in chalcocite. Some are less than one micron thick and are barely visible at 500 diameters magnification of a polished cross section. Some chalcocite is present as a in in the gangue. Various oxidized copper minerals are present as a result of oxidation in place but they represent a minor proportion of the copper minerals of the ore body. Oxidation

Jan 1, 1949

By John Vickers, William H. Hover, Paul C. Schmall

"Any sudden subsurface issue that threatens the stability of existing buildings or infrastructure is cause for immediate investigation and prompt remedial action. Nowhere is this more true than the nation’s dams and levees. A breach of any kind, no matter how small initially, has the potential to be catastrophic and impact a wide downstream area. Addressing the problem quickly and effectively is therefore critical. When a turbid water discharge developed from a rock drainage embankment at the toe of the earthen dam impounding Cannonsville Reservoir, near Deposit, NY, the source of the problem was quickly identified as resulting from an artesian water release from an underlying permeable silty sand and gravel formation during drilling of three exploratory boreholes in preparation for construction of a hydroelectric plant at the downstream toe area of the dam facility. Work was halted, intense 24-hour monitoring was implemented, and as a risk reduction measure NYCDEP began to draw down the reservoir’s total storage at a rate of a billion gallons per day. Input sought from contractors within the geotechnical community helped result in the design and development of a deep well system to control the artesian pressure. Once this primary objective was accomplished, modified compaction grouting was performed at the borehole locations to densify loosened soils, fill any voids created by the discharge activity, and seal off the permeable aquifer. This paper discusses the dewatering program, specialized drilling techniques required, monitoring and verification of pressures within the dam, and the grouting program.BackgroundCannonsville Dam, owned and operated by the New York City Department of Environmental Protection (NYCDEP), is located in Deposit, New York on the West Branch of the Delaware River and impounds the Cannonsville Reservoir. Built between 1959 and 1964, the dam has an impervious central and upstream core zone keyed into the glacial till foundation, a semi-pervious downstream embankment zone, and a rockfill toe and is approximately 2,800 ft (853.4 m) long and 175 ft (53.3 m) high. The dam is formed by two embankment sections. The left section forms the main embankment blocking the main river channel, while the right section is constructed over a topographic saddle or low ridge. Reservoir level is actively influenced by withdrawals through the West Delaware Tunnel, based on water supply need. Under normal circumstances, water is continuously discharged downstream to the Delaware River."

Jan 1, 2016

By I. Hawke, K. Barron

I. Hawkes (Postgraduate School in Mining, University of Sheffield, Sheffield, England) — The photoelastic stressmeter is proving to be a very practical tool for 'in-situ' measurements in the fields of civil and mining engineering and Barron's article has therefore come at a very opportune time, supplementing as it does, the considerable amount of laboratory and field data which is being accumulated.1,2,3 There are however several points relating the application of Barron's conclusions to the practical use of the meter which require further elucidation. EASE OF READING If the photoelastic stressmeter is to have a wide application, the fringe orders must be easily measured. The system adopted by the writer and his colleagues at Sheffield for the uniaxial stress case is to read the fringe order at the 45 point, 0.20 in. from the center (11/4 in. diam meter). This procedure has been recommended because the fringes not at this point form a very distinct 'eye' which is obvious even to those who have had little experience with photoelastic fringe patterns. Barron points out that this point can also be used up to a stress ratio of 0.33 and in practice this is normally done. In biaxial fields above a ratio of 0.33 the 'eye' is no longer apparent and the fringe order must be ascertained at some other point. The writer and his colleagues experimented at various points and finally chose a point at a distance 0.175 in. (11/4 in. diam meter) on the minor stress axis and fixed this point on the meter by inserting a collar of this diameter. This procedure enables the 'eye' technique to be used for uniaxial stresses as the 'eye' falls outside the collar; any other technique for biaxial patterns would require lines to be engraved on the meter itself and reading difficulties would be experienced by all but the most highly trained. It is interesting to point out that in a great many field applications ranging from underground pillars to building foundation piles the stresses measured have been uniaxial. In such cases, reading the fringe order has been simple even for unskilled persons. SENSITIVITY The photoelastic stressmeter acts as an inclusion, and as such its theoretical behavior is as described by Barron's mathematical analysis. When considering its practical application, however, it must be remembered that rocks and concrete are not mathematically ideal substances. The theory relates the fringe order in the meter to the stresses and the E (Young's Modulus) and the µ (Poisson's Ratio) values of the surrounding material. There is of course no unique E or µ value for rocks or concrete. These values change both with stress level and time load application sometimes to the order of 300%. We at Sheffield have very accurately calibrated the photoelastic stressmeter in a wide range of materials and have also measured the average E values for these materials. The results prove that the meter sensitivity

Jan 1, 1965