Search Documents

By Tsutomu Yamamura

The electrolytic reduction mechanism of rare-earth chlorides such as LaCl3, CeCl3, NdCl3, ` SmCl3 and DyCl3 in alkali chloride baths has been investigated in NaCl, KCI and eutectic LiCI- KCI by means of electrochemical transient methods. The thermodynamic behaviors of rare-earth containing species have been discussed in the frame of Electrode potential - P02- diagram. Low current efficiency found in the case of Nd electro-winning has been attributed to the dissolution of Nd into the bath. The analyses of electrochemical measurement required the elucidation of the effects of the factors such as under-potential deposition, metal dissolution, moisture and oxygen partial pressure.

Jan 1, 2003

By Stephen H. E. Phillips

Geological and hydrological conditions in the strata overlying the Salado Formation vary considerably in the Carlsbad, New Mexico area. The first four shafts sunk at international Minerals and Chemical Corporation's property have been located in competent and essentially dry conditions, while other shafts on adjacent properties have had such adverse conditions that ground freezing has been chosen as the water and ground control technique for shaft sinking. At the location of the IMC No. 5 Shaft there has been extensive-erosion and salt dissolution in the Rustler Formation which has led to collapse of some zones of the strata. Both ground freezing and pregrouting were considered as alternative methods of stabilizing the extremely poor ground conditions and controlling the potentially very heavy water inflows it was decided that pregrouting the shaft was feasible and would offer substantial cost and time saving over a ground freezing technique. This paper describes the pregrouting techniques used and illustrates the requirement for flexibility in a grouting program so that it can be codified to reflect any new or additional information which is obtained during the progress of the grouting.

Jan 1, 1984

By Rudolph H. Jacobson

The leaching of heaps or sub-marginal waste ore dumps as it is practiced throughout the Southwest as well as other parts of the world, is the major method of secondary recovery of copper. In 1970, twenty percent of all domestic copper was produced by dump leaching operations (l). In recent years, this method has been successfully extended on a limited scale, for the recovery of uranium from low-grade ores (2). It is inevitable that this technique will be increasingly employed in metal production to satisfy the insatiable demand of our mineral based society. Although dump and heap leaching has been used effectively for some time (3) , its application has been more of an art than a science. Therefore, it is essential that we learn about the important factors and parameters affecting this versatile process so that we may make increasing use of this technique in the future. The dump or heap leaching process encompasses the preparation of ore for-subsequent inplace leaching, the flow of solutions and ionic species through porous rock masses, the leaching of minerals with inexpensive and, if possible, regenerable lixiviants under prevailing conditions of the inplace environment, and the recovery of metals from the pregnant liquors. It is evident that this comprehensive scope of dump or heap leaching falls under the realm of interdisciplinary science and engineering requiring the application of the principles of physics, mineral engineering, hydrology, computer modeling, operations research, economics, and allied disciplines. An exhaustive study of the phenomenology of a leach dump or heap requires detailed knowledge of the simultaneous interaction of'

Jan 1, 1972

By R. B. Shu

A moderate thermophilic microorganisms, has been isolated (45?) from a typical sulphide mine in the region of Mo Jiang located in the southwest of China. The culture has been used to extract copper from chalcopyrite concentrates obtained from De Xing copper mine. The majority of experiments were carried out in 300mL Erlenmeyer flasks containing 150mL volumes of mineral suspension. Effects of some variable parameters such as solids concentration, pH and the concentrations of inorganic nutrients on the bioleaching of chalcopyrite obtained from De Xing copper mine were investigated. For a given concentrate the most important factor affecting the fractional copper extraction was the size of the mineral particles. The overall rate of leaching was found to be limited by the area of mineral surface. The attack started in cracks and genetic defects and finally reached the whole chalcopyrite surface. As a consequence of this, the ore showed strongly cracks. The additive of ferrous sulfate increases the bacteria activity, but did not improve chalcopyrite bioleaching. The results indicate that the nature and relative proportions of the various minerals present have been shown to be important factors.

Jan 1, 2014

By G. S. Zeng

The mechanism of cobalt removal from zinc sulfate solution with zinc dust is still not understood well. The experiments in this paper were carried out by zinc dust from zinc sulfate solution with high cobalt to study the mechanism of cobalt removal. Residues after the cementation process from zinc sulfate solution were analyzed by SEM and Electron probe micro-analysis (EPMA) to investigate the morphology of products. Different temperature will cause different structure of particles. With the increasement of temperature, cobalt removal can be improved considerably. The mechanism of cobalt removal by zinc dust is thought as follows: firstly, the cobalt ion forms Co-Zn alloy with zinc particles, and the reaction reaches equilibrium quickly; secondly, the Co-Zn alloy continues reacting to Co with Co2+, which is the control procedure of the whole reaction.

Jan 1, 2014

By D. Furrer, M. Dallaire

The arrival of Image analysis in the last 20 years has changed the world of quantitative metallography. Many standard measurement techniques which were previously manual can now be done with fully automated systems. This reduces subjectivity and operator fatigue and therefore enhances the quality of the statistical results. In many laboratories, Titanium Alloy microstructures continue to be evaluated by traditional methods, where quality of results is subject to operator fatigue and level of experience. Advances in Camera technology have tremendously improved image acquisition. One can often see clearly at 500x what can not be observed at 1000x, allowing for a larger area to be analyzed, without the inconveniences associated with very high magnification objectives. Powerful and versatile Image analysis software combined with a high precision motorized stage gives access to a multitude of applications, which were extremely challenging or impossible until now. Image Analysis tools such as Multilayer Grab, which reconstructs an uneven image into one plane of focus (ex. Observation at high magnification of texture resulting from etching) and Mosaic which builds an image from a number of fields of view (ex. Reconstruction of very large grains at low magnifications) expand even further the power and flexibility of IA systems. This presentation will describe how automated methods are applied to the point count method and grain size measurement. We will show how cameras and software work together to permit quantitative measurements of primary alpha and prior beta microstructures, as well as lamellar alpha plate thickness in titanium alloys.Automated and semi automated quantitative measurements of various Titanium microstrures have been assessed, using the Clemex Vision PE. Examples of the methods and steps used are presented.

Jan 1, 2006

By G. A. Howes

This is one of a series of circulars dealing with the cost of equipping and developing mining properties in the United States and Canada, prepared and published by the Bureau of Mines in cooperation with various mining and exploration companies. This group of circulars is designed to supplement an earlier series which covered the methods and costs of mining and milling at a large number of producing properties. ACKNOWLEDGMENTS The authors desire to thank Robert A. Bryce, president of Macassa Mines (Ltd.), for permission to use the data presented in this paper, and to acknowledge the cooperation of A. J. Keast, under whose direction as manager the plant was installed and equipped and the shaft was sunk to a depth of approximately 2,000 feet.

Jan 1, 1932

By I. P. Swainson, A. Ilbagi, H. Henein

Powders of Al-50wt%Ni, Al-40wt%Ni and Al-36wt%Ni were produced using the Impulse Atomization technique, a rapid solidification technique. The molten droplets were cooled in-flight by the stagnant helium or nitrogen in the atomizing chamber. The resulting powders were sieved into different size ranges. X-Ray diffraction and neutron diffraction were used in order to quantify the phase fractions in the samples. The computer software GSAS was used to calculate the weight fraction of the existing phases, namely Al3Ni2, Al3Ni and Al, by profile refinement method. The effect of processing parameters, alloy composition and particle size will be discussed in this paper. In brief, no AlNi was found in any of the samples analyzed. Higher cooling rates resulted in the reduction of the ratio of Al3Ni/Al3Ni2. Also, at high cooling rates, Scheil closely predicted the ratio of Al3Ni/Al3Ni2. Some metastable phases were found in Al- 36wt%Ni.

Jan 1, 2010

By R. Padilla

A thermogravimetric study has been conducted to follow the decomposition and volatilization of arsenic from enargite concentrate in nitrogen and slightly oxidizing atmospheres. Temperature has a large effect on the rate of volatilization of arsenic. Fractional volatilization of arsenic as high as 98% were obtained in less than 60 min at 650°C in nitrogen atmosphere, while in slightly oxidizing atmosphere the same volatilization could be achieved in 30 min. It was found that arsenic volatilizes as sulfide in nitrogen atmosphere and as 4xture of sulfide and oxide in atmospheres containing 1% oxygen. By using the pore blocking and the first order kinetic models, apparent activation energies of 213 and 200 kJ/mol for the temperature range of 780 - 900 K and 205 and 184 kJ/mol for the temperature range of 900 - 985 K were determined for enargite and copper concentrate, respectively.

Jan 1, 1997

By Maria Salazar-Villalpando, Todd H. Gardner

"Efficient utilization of CO2 can help to decrease global warming. Methane reforming using carbon dioxide has been of interest for many years, but recently that interest has experienced a rapid increase for both environmental and commercial reasons. The use of CO2 provides a source of clean oxygen, which eliminates the need for costly oxygen separation plants. The product of dry reforming is useful syn-gas, which can be used to generate electrical power in a SOFC or in the production of synthetic fuels (hydrocarbons and alcohols). Hexaaluminate catalysts prepared at NETL may represent a product that can be utilized for the conversion of CO2 to syn-gas. In this work, transition metals dispersed in barium hexaaluminate have shown to be promising new catalysts for dry methane reforming. In this investigation, a series of BaNixAl12-yO19-d catalysts with varying Ni content were prepared by co-precipitation followed by calcination at 1400°C. CO2 reduction by dry methane reforming was carried out to determine catalyst performance as a function of temperature and carbon formation was also quantified after the reforming tests. Results of catalysts characterization, dispersion and surface area, were correlated to catalytic performance.IntroductionEfficient utilization of CO2 can help to decrease global warming. Methane reforming using carbon dioxide has been of interest for many years, but recently that interest has experienced a rapid increase for both environmental and commercial reasons. The use of CO2 provides a source of clean oxygen, which eliminates the need for costly oxygen separation plants. The product of dry reforming is useful syn-gas, which can be used to generate electrical power in a SOFC or in the production of synthetic fuels (hydrocarbons and alcohols). The dry reforming reaction has been known for a long time. Recent publications have reported studies over several catalysts. For example, the CO2 reforming of CH4 over mesoporous nanocrystalline zirconium powders (ZrO2–3%M2Ox; M: Ce, La and K) at 700ºC have shown methane conversion up to 60% (1). Similarly, the effect of Ni content (1–12 wt%) on the surface and catalytic behavior of bimetallic PtNi catalysts supported on ZSM-5 for reforming of methane with CO2 has been studied and report shows a maximum conversion of 16% and catalyst deactivation was observed during the first hour of time on stream (2). In another report, (3) Ni/a-Al2O3 catalyst was tested for syn-gas generation at 750ºC. The maximum methane conversion was 25%."

Jan 1, 2008

By Min Chen, Zhen Tian, Hongxu Cui

"The effects of adjusting technology on the phosphorous enrichment in converter slag were investigated. The results showed that the grain size of 2CaO·SiO2 with high phosphorus containing content increased slightly with the decreasing of cooling rate, and the proper cooling rate was confirmed to be about l.0°C.min-1. Moreover, the morphology of the phosphorus-rich phase of 2CaO·SiO2-3CaO·P2O 5 was changed from granular for the higher basicity of converter slag to the coexistence of granular shape and rod-like for the lower basicity of adjusted slag. With the addition of adjusting agent such as SiO2 to lower the basicity of converter slag, the phosphorus in converter slag could be transferred into 2CaO·Si02 phase effectively, and P2O 5 content in high phosphorus containing phase reached to above 30%.IntroductionThe yield of converter slag is very large in China, but most of the slag is stacked usually after the separation of iron, which not only takes up a lot of land, but also affects the ecological environment seriously. Therefore, improving the comprehensive utilization and value-added products of converter slag is of great significance to recycle the steelmaking slag[l-3]. On the other hand, the refining of hot metal with high phosphorous content is an unavoidable problem with the decreasing of high grade iron ore, and as a result, more amounts of high phosphorus containing steelmaking slag are produced. However, the current recycle of converter slag is more focused on the emission reduction and reuse of steelmaking slag inside the iron and steelmaking process without considering the recycle of phosphorous resources[4-6]. At the same time, the development and utilization of phosphate ore as a strategic resource is drawing more and more attention, but the phosphate ore in China is mostly low grade and significant amounts of tailings are produced which is harmful to the environment. Therefore, it is important to separate phosphorous resources in steelmaking slag which can be used as phosphate ore for fertilizer material[7-9].Literature studies showed that most of the phosphorus in steelmaking slag existing as 2CaO·SiO2-3CaO·P2O 5 solid solution phase in 2CaO·SiO2 particle. The P2O 5 content in the phosphorus containing phase is very low due to the fact that the basicity of converter slag is usually high and the precipitated amounts of 2CaO·SiO2 particles during cooling are very large, resulting in the fact that the P2O 5 contents in 2CaO·SiO2-3CaO·P2O 5 solid solution phase are much lower which is impossible to be used as phosphorous resources instead of phosphate ore. Thus, the enrichment of phosphorus in steelmaking slag is need[ 10-14]."

Jan 1, 2011

By R. N. Reddy

The Pseudo capacitance of layered type Mn02 electrode material for electrochemical capacitors (EC's) was investigated. MnO2 was synthesized in our laboratory. Mn02 was prepared from heating of KMn04 at 300°C in air. Cyclic Voltammetry (CV) experiments were carried out using three electrode system, Saturated calomel electrode as reference electrode, platinum mesh as a counter electrode, and MnOz composite material mounted in a platinum mesh used as a working electrode. Two kinds of composite working electrode materials were used, one was mixture of MnOz and 25 wt% acetylene black, while the other was MnOz, 25 wt% acetylene black and 25 wt% carbon. All the experiments were carried out at 25OC. A maximum specific capacitance of 130 Fig and 118 Fig were observed at the scan rate of 2 mV/s and 20 mV/s respectively in 1M KC1 for composite electrode made with carbon. Results obtained in this study are compared with that of other electrode materials.

Jan 1, 2002

By J. M. Stuve

Standard heats of formation (AH°p) of YbCl3 (c) and TmCl3 (c) were measured by solution calorimetry. Heat of solution data are given for ytterbium and thulium metals and corresponding anhydrous trichlorides in 4.360 molal hydrochloric acid. The derived standard heats of formation of YbCl3 (c) and TmCl3 (c) were -229,370 ±720 and -235,820 ±400 cal/mole, respectively, at 298.15° K. The resulting heats of formation for YbC13 and TmCl3 are about 1 kcal and 6.3 kcal more negative than previously published values.

Jan 1, 1967

By J P. Barkas

World demand for iron ore is far from peaking, and the substantial price decline that has captivated commentators since early 2014 is not the result of widespread misreading by producers of the prospects for global market growth. Recent price movements provide little useful insight into the industry’s longer-term fortunes, apart from reminding mining companies that their businesses need to be robust against the volatility and inescapable cyclicality of mineral commodity markets. It is timely to take a strategic view of the history and longer-term prospects for the iron ore industry and of Australia’s place in it.CITATION:Barkas, J P, 2015. Perspectives on the long-term outlook for iron ore, in Proceedings Iron Ore 2015, pp 3–6 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Carlo Sampaio, Moacir Veras, Aaron Young, Carlo Petter

"Three major challenges for the mining industry are the minimization of energy use, water consumption and environmental impact. Therefore, any technique that reduces milling waste, decreases water usage and shrinks impact during mine life must be considered a major innovation in mining.To these ends, one of the most impactful developments in mining within the last 10 years has been the expanded use of high technology sensors to create preconcentrations of mine ore (Jönsson, 2014). The most common sensors used are charge-coupled device (CCD) cameras, that allow through a red, green and blue (RGB) coloring system, the separation of minerals with different colors, tones and, in many cases, with differences in brightness.More recently, the development and use of dual energy X-ray transmission (DE-XRT) to enable the separation by atomic density of the constituent minerals within a given rock has become a reality. Within this work, a rapid bibliographical review of the CCD and DE-XRT methods and examples of their usage within mining and the industrial minerals sector are presented.Sensor-based sorting in miningAutomation within mining is one of the industry’s current goals. Sensors of various kinds have been used as steps toward automation in recent years, from improving the safety and productivity of haul trucks through the use of cameras and global positioning satellites (GPS), to the divination of slope failures. Just as with other mining areas, sorting has improved dramatically and made great steps toward automation in recent years (Wotruba et al., 2014).Sensor-based sorting (SBS) uses spectromatic sensors to identify intrinsic characteristics of particles and separates them by either mechanical or pneumatic means into different product streams (Wotruba et al., 2014). SBS can be used with great effectiveness to improve gravimetric beneficiation through the selective separation or preconcentration of run of mine ores (ROM)."

Jan 1, 2015

By Sutham Niyomwas

Biomorphic Cellular TiCIC ceramics were produced by vacuum-infiltrating carbon preforms with Ti02 sol and subsequent synthesis by the carbothermal reduction process. The carbon preforms used in the study were obtained by pyrolysis of parawood and neem wood. The effect of infiltration time on the composition and microstructure of the biomorphic TiCIC ceramic was analyzed by X-ray diffractometry and scanning electron microscopy. The biomorphic structure of the TiCIC ceramic is consistent with that of the biotemplate natural parawood and neem wood.

Jan 1, 2008

By Kunio Nakahara, Kashiwagim Junichi, Takao Hayashi

"There are many problems for electronic devices and parts which were caused electrostatic damage by static electricity. It is necessary for prevention of electrostatic charge to decrease surface resistivity of material using electroconductive coating. Mitsui Mining & Smelting Co., Ltd. developed metal oxide type electroconductive pigment PASSTRAN (trade mark) Type-IV which is barium sulfate coated with SnOz(Sb) thin electroconductive layer. This paper shows about pigment characteristics and film condition of antistatic transparency paint which contained PASS TRAN.L.IntroductionRecently rapid development of electronics technology diffused electronic devices and products to Office, Factory, Laboratory and our life. But the other side, there are many problems for electronics parts which were caused electrostatic damage under static electricity. Demand of antistatic materials were become lager by this situation.There is close relationship between surface resistivity of material and static electricity. If the surface resistivity of object is enough low (under 109 Q /Sq), static electricity is dissipated quickly. So it is necessary for prevention of electrostatic charge to decrease surface resistivity of material using electroconductive coating.1) There are many type of electroconductive materials, for example, carbon black, metal powder, electroconductive polymer and so on. Especially, carbon black is used for general purpose by reason of its low cost, but it has big problem of black color. It can not get any color without black, and it caused contamination of carbon.In recent years, metal oxide electroconductive pigment (ECP) was developed and used for special purpose which demands transparent coating or easy dispersion to make ECP paint or endurance under hard environment and so on. Mitsui Mining & Smelting Co., Ltd. developed electroconductive pigment PASSTRAN Type-IV which is BaS04 coated with electro-conductive Tin oxide layer."

Jan 1, 1998

By S. G. Sawyer

The Pittsburgh Safety and Health Technology Center (PSHTC) of the Mine Safety and Health Administration (MSHA) provides engineering and scientific support to the inspectorate personnel of MSHA. One of the Center's myriad roles is to assist in the investigation of mining accidents, especially those involving fatalities. Center personnel utilize forensics to help uncover the causes of accidents and to make technical recommendations on the prevention of future similar mishaps. To exemplify a typical forensic investigation, this paper documents the methodology used in determining the reasons for a boat sinking, which resulted in a double fatality on a mine company pond.

Jan 1, 1997

By R. Tunold, Y. J. Zhang

"The cathodic kinetics of aluminum deposition from aluminum chloridealkali chloride melts was studied by use of electro-cnemical transient techniques at 700 °C. Aluminum deposited as an insoluble product on a glassy carbon electrode and as a partly soluble product on a tungsten electrode. The deposition was found to be a simple diffusion controlled process involving the exchange of three electrons. The diffusion coefficient of aluminum chloride was calculated - 4.sx10-s cm2 ·S-I in AlCl3 -NaCl-LiCl melts and 2.6x10-s cm2 ·S-' in AlCl3 -NaCl-KCl melts. For AlCl3 -NaCl-CsCl system the diffusion coefficient exhibited some uncertainty due to nucleation. The determined rate constant of aluminum deposition reaction was on the order of 10-' -10-2 cm'S:' Constant potential electrolysis was carried out. TiB2 was well wetted by aluminum. The species of melts penetrated into graphite and glassy carbon but not into tungsten. The diffusion coefficient of species in glassy carbon was evaluated.IntroductionAluminum chloride electrolysis is attractive for its power saving of 30%. Different process to circumvent the conventional chlorization to obtain aluminum chloride economically, such as directly chlorizating mixture of Al~03 and C in a cell with A-shaped laminated bipolar electrodes by rising chlorine (1), or by use of a composite anode (2), will promote the electrolysis technology to be realized industrially. With the appearance of the Alcoa process periodically there are studies on the kinetics of aluminum deposition. Some discrepancies seem to exist on the mechanism of aluminum deposition. Borne studies (3,4,5) showed that the deposition of aluminum was hindered by diffusion process in the melts. M.Gabco et a1. (6) claimed a preceding dissociation of a complex being the rate controlled step. This paper presents our results on the mechanism of aluminum deposition from the study by use of transient techniques and some results from constant potential electrolysis."

Jan 1, 1988

By George Nekoksa

The biofilm activity monitoring probes measure applied current during intermittent short-term polarization of the probe electrodes and current or potential between the electrodes after removal of the polarization. The probe polarization mimics conditions at crevices, welds and inclusions where the biofilm activity and microbially influenced corrosion usually concentrate. Monitoring of AC resistance between the probe electrodes can provide infornation about the thickness of deposits.

Jan 1, 1994