Search Documents

By I Lourel

In evaluating the installation of an in-pit crushing and conveying (IPCC) system for any mine, a number of options are available for each of the dig side, transport and dump side operations. Some of them are moreappropriate than others; given the pit arrangement, the material being handled and the rates at which it needs to be moved. This paper seeks to document the options that might be employed, and to rank them in terms of their applicability at any mine and their practicality overall, with a view to nominating those that would be most suitable for further study.

Jan 1, 2009

"Far from being eclipsed by petroleum and natural gas, Canadian coal continues to command wide (and apparently growing) interest.Major R & D investigations are currently heavily oriented toward coal beneficiation (e.g., cleaning and utilization of fines) and toward a broad range of studies on metallurgical coals and cokes. However, active work is also being carried out in the areas of coal geology, mining, transportation and combustion; and, in some laboratories, increasing stress has been laid on developing a number of new, essentially non-fuel uses for coal and coal products.This review summarizes the work of Canadian coal research agencies during 1966 and indicates some of the more important advances made by them."

Jan 1, 1967

By C. H. Johnson

This paper on the out-and-fill method of mining is one of a series on mining methods published by the United States Bureau of Mines. It has been compiled chiefly from recent publications of the bureau describing in detail mining methods and costs at various mines. Other sources of information were the technical press, the Transactions of the American Institute of Mining and Metallurgical Engineers, the Mines Haudbook, and company reports. References other than those mentioned in Table 1, which lists the mines entering into this discussion and gives general data regarding them, are given in the body of the paper. The authors wish to acknowledge the kind assistance of many operating officials, either through correspondence or in the course of numerous visits to their mines. DEFINITION OF CUT-AND-FILL STOPING The out-and-fill method of stoping is that method in which relatively small sections or slices are taken successively from the lower surface of a block of ground by open-stoping methods, the broken ore being removed and each section filled with waste material before the next is mined. This definition excludes shrinkage stoping, even with subsequent filling; it excludes square-set and fill methods; it excludes the Mitchell slice method, which may be classed as underhand square-setting; it excludes the systematic use of stull sets and filling, which is a variation of square-setting; it excludes any method involving the caving of the ore, walls, or overburden during the process of extraction, although caving may be allowed to take place when the waste fill is withdrawn for use in other stopes; and it excludes any open-stope method without filling. Through variations, which will be discussed later, the cut-and-fill method merges into shrinkage stoping, open stoping, or square-setting. The use of casual timber support, such as props, stulls, or timber cribs for holding up weak portions of the back does not constitute a change from cut-and-fill to square-set mining.

Jan 1, 1933

By Andrés Llatas

El presente trabajo describe el comportamiento anódico de los sulfuros de cobre en las soluciones de ácido sulfúrico y férrico a través de la técnica potenciostática. En este sentido, se realiza una interpretación de los fenómenos psíquicos y cinéticos de la disolución en los sulfuros de cobre, considerando su importancia económica y las características de materiales refractarios que poseen los procesos convencionales de lixiviación.

Aug 26, 1988

By André de Albuquerque Vicente

Os aços inoxidáveis duplex caracterizam-se por apresentarem microestrutura bifásica, ferrítica-austenítica. A fração volumétrica ideal das fases é 50% de ferrita e 50% de austenita, entretanto, essa condição é de difícil obtenção quando realiza-se a união por soldagem a arco desses materiais. Neste trabalho estudou-se as melhores práticas de soldagem do aço inoxidável duplex UNS S31803 garantindo a obtenção de frações volumétricas ideais de ferrita e austenita. Foi soldado um corpo de prova pelos processos TIG e MIG-MAG. Para esse corpo de prova foi realizada a soldagem de um passe de raiz e um passe de reforço através do processo TIG e o preenchimento da junta através do processo MIG-MAG. Foram realizados os seguintes ensaios no corpo de prova: micrografia (metal base, ZAC face, ZAC raiz, face da Zona Fundida e raiz da Zona Fundida), medição da fração volumétrica de ferrita, microdureza Vickers (HV500), ensaio de tração da junta soldada, dobramento guiado, Charpy e ensaio de corrosão por pitting.

Oct 30, 2017

By Taciana Rezende Pereira

O aço 10B06 é utilizado na produção de fio máquina para trefilação. Por ser produzido em aciaria elétrica, o teor de nitrogênio desse aço tende a ser elevado, o que pode causar o fenômeno de envelhecimento, resultando em aumento de resistência e queda de ductilidade. Os dois principais fatores que influenciam na microestrutura e propriedades mecânicas do material são a composição química e o processo produtivo. A análise metalográfica realizada com Nital revelou microestrutura composta de 88% de ferrita e 12% de perlita, enquanto o reagente Le Pera identificou ilhas de martensita e/ou austenita retida (MA). Através das análises de raio x foi possível identificar a presença das fases a e cementita e manganês em solução sólida. A análise fractográfica mostrou que o modo de fratura observado no material foi dúctil, entretanto pequenas regiões de ruptura frágil também foram identificadas. Com o objetivo de melhorar as características de trefilabilidade do material, sugere-se a redução do teor de nitrogênio e consequente queda do boro adicionado, e/ou aumento da temperatura inicial de resfriamento do material, dificultando o enriquecimento da austenita em carbono e a consequente formação do microconstituinte MA.

Oct 30, 2017

By ANDERSON OLIVEIRA DA SILVA

O tecido de poliamida aromática (poliaramida) da marca Twaron foi reforçado por uma solução de óxido de grafeno para a produção de um nanocompósito, e posteriormente submetido a tratamento térmico. A impregnação do óxido de grafeno no tecido de poliaramida visa melhorar as propriedades balísticas do material por meio do aumento do coeficiente de atrito entre as fibras do tecido. Este estudo avaliou a adesão das folhas de óxido de grafeno nos tecidos de poliaramida, utilizando a análise por espectroscopia de infravermelho por transformada de Fourier (FTIR), a análise termogravimétrica (TGA) e a microscopia eletrônica por varredura (MEV), após o tratamento térmico. Por meio da análise dos resultados, foi possível observar que a adesão do óxido de grafeno aumentou com o tratamento térmico empregado neste trabalho.

Oct 30, 2017

By Robert L. Lappi

This report covers the final phase of a project demonstrating the economic efficiency of cross-ridge mountaintop coal mining. A demonstration mine was established at Big Wheel Gap in northeastern Tennessee. Not only was cross-ridge mining feasible for the selected site, but parallel cut methods could not be used due to a deficit in available spoil storage. Cross-ridge mining permitted coal extraction at a cost almost identical with costs simulated by computer projections using mathematical optimization techniques. No unexpected environmental problems were encountered. Volume I is accompanied by Volume II which describes the MATHMINE Mine Simulation System, software used to support the mining demonstration.

Jan 1, 1984

By D. N. Golenkov, N. I. Lomaka, A. V. Kozub, T. V. Ignatova, E. V. Shelepov, D. O. Sharkovskiy, A. V. Chanturiya, R. I. Ismagilov

The modern Russian iron ore mining industry is faced with multiple challenges from everincreasing requirements of steel-making, the value of iron ore concentrates, depletion of high-grade ore reserves and complications of the mining and geologic environment’s necessity to process low-grade ores with complex material composition and low valuable mineral content; with finely disseminated aggregates of metal and non-metal minerals responding similarly to processing. The upgrade of the existing operations’ fine wet screening was implemented by Metalloinvest; as well as the design of a process flowsheet for concentration oxide ferruginous quartzites with low concentrating ability. The scientific basis for improvement of low grade ore concentrating efficiency and the upgrade of market product quality is supported by an in-depth study of ore characteristics, application of high performance equipment for separation of fine-grained mineral aggregates and use of depressor selective to ferruginous minerals in the flotation process. The benefits of wet fine screening have been proven by industrial scale tests; as well as the feasibility of significant upgrades in product quality which have been confirmed as a result of the tests. A road-map for the upgrade of an existing process for the concentration of unoxidised ferruginous quartzites deposited in the Mikhailovskoye ore field was developed, based on the industrial scale test of a fine screening process. With reference to the ability for concentration, three major ore types oxidised ferruginous quartzites were defined as a result of comprehensive geological mapping and process sampling: oxidised ferruginous quartzites with good concentrating ability: over Fe67% grade of concentrate with ca. 80% iron recovery; oxidised ferruginous quartzites with moderate concentrating ability: Fe65-67% grade of concentrate with 70-72% iron recovery oxidised ferruginous quartzites with low concentrating ability: below Fe60% grade of concentrate (cannot be processed into desired grade market product). A process flow diagram combining magnetic separation and flotation has been designed and recommended for implementation based on the in-depth research of defined Mikhailovskoye deposit iron oxide types, including grain size, chemistry, petrographic, mineralogy, hematite and magnetite grain size distribution and liberation analysis.

Jan 1, 2020

By E. J. Peuraniemi

Oxidation of chalcopyrite concentrate and two low-iron copper mattes were studied using a laboratory scale laminar-flow furnace simulating the phenomena taking place in different zones of the reaction shaft of a flash smelting furnace. In the experiments, screened fractions were fed into the furnace and sampled after short reaction time intervals by quenching them into a water film. Experimental conditions included temperatures of 1100 and 1300°C with reaction gas oxygen contents from 21 to 75 vol.%. Samples were analysed chemically for Cu, Fe and S to define removal rate of sulphur. Optical and scanning electron microscopy with EDS-analyser were used to examine the samples. In this paper, oxidation kinetics as well as ignition of particles are discussed. Changes in particle morphology, size, and composition are viewed to closely define the proceeding of the oxidation, and, consequently, to compose a detailed model of dust formation and reaction mechanisms. Data obtained in the experiments broadens the knowledge of physical and chemical phenomena in flash reactions and serves as reference for computer simulations.

Jan 1, 2000

By Jurgen H. Kleinau

This paper details Keeler/ Dorr-Oliver's experience with the application of fluid bed combustion technology to the burning of coal-mining waste. The designs of two stage fluid bed combustors/dryers are demonstrated as useful in the drying of coal, slag and coke, using coal and coal refuse (gob) as fuel. Anthracite mining refuse (culm) is more than abundant in Northeastern Pennsylvania. After demonstration at Shamokin, Pennsylvania, a full commercial-sized fluid bed boiler using culm is used for district heating in Wilkes-Barre, Pennsylvania. Limited research work has shown the utility of using fine coal as filter aid in sludge in¬cineration. With the rising avenues of the suitability of coal as auxiliary fuel in fluid bed sludge incineration, an expansion of these concepts combines the use of coal or coal refuse as filter aid and auxiliary fuel. Lime¬stone addition controls SO2 emission.

Jan 1, 1985

By B. Wasmund, M. Y. Solar, I. Candy

The nickel laterite industry is divided into two camps when it comes to the grade of the ferronickels produced. One group, led by Falcondo and Cerro Matoso, markets high-grade ferronickels in the range of 35 to 40% nickel, while another group, led by SLN and the Japanese smelters, favour lower grades in the range of 20 to 25%. Because the ores processed by these smelters vary widely in terms of nickel content and iron to nickel ratios, it is probably more accurate to classify these smelters in terms of their iron recovery: Falcondo and Cerro Matoso smelt at lower reduction potentials and thus recover only 15 to 30% of the iron in their ores, while SLN and the Japanese smelters are very reducing and recover 45 to 65% of their iron. Low reductions generally imply higher slag losses and lower nickel recoveries, but also lower power and reductant requirements; higher reductions, the reverse. The question is, therefore, whether an economically optimum ferronickel grade exists for processing any given ore. This paper proposes a methodology for determining this optimum grade and concludes that nickel laterite smelters should favour low reductions and production of high-grade ferronickels.

Jan 1, 2008

By Andrew M. Leszcykowski

A 1981 U.S. Bureau of Mines investigation indicates the Panamint Dunes Wilderness Study Area (WSA) has one active (intermittent) mine,--borrow pit MS 242 owned by the California Department of Transportation (Cal Trans). This mine produces cinders for road base and traction grit. It contains about 900,000 tons of inferred reserves. Examination and sample analyses indicate the Panamint Dunes deposit, covering about 480 acres of the WSA, may have silica resources and the Green Quartz Claim may have copper resources. Carbonate rocks occur in the WSA, but stone resources have not been identified. Adjacent to the WSA, the Big Four Mine contains 35,000 tons of inferred subeconomic zinc-lead-silver resources, and may have additional resources. Sample analyses indicate the Apple 1 Claim, also adjacent to the WSA, may have silver-lead-zinc resources.

Jan 1, 1985

By M. L. Mellish

The year 1988 unexpectedly turned out to be a good year for the US coal industry. In fact, it was a third consecutive year of record coal production. Accord¬ing to preliminary Energy Information Administration data for 1988, domestic coal consumption went up 5%, or 41 Mt (45 million st), from 1987. Coal exports were up by a surprising 13.6 Mt (15 million st). In 1988, 22.7 Mt (25 million st) of coal were drawn from stockpiles for consumption. Even so, US coal production increased to 862 Mt (950 million st). That was up 28 Mt (31 million st) from 1987. While coal consumption, exports, and production were up, delivered prices for steam coal continued to slide during the year. Metallurgical coal prices, however, firmed up and showed a moderate increase. This reflected tight metallurgical coal markets at home and abroad. Coal consumption US coal consumption reached 800 Mt (882 million st), compared with 759 Mt (837 million st) in 1987. Increased metallurgical coal consumption was one factor. Most of the rise in coal consumption, however, was due to unexpectedly high electricity demand. Unseasonably hot summer weather al lowed added coal-fired electric generation to supplement the drought-related reduction in hydro-electric power supply. Electric utilities consumed 687 Mt (757 million st) of coal in 1988, 35.4 Mt (39 million st) more than in 1987. Coal-fired power plants remained the primary source of US electricity generation, providing 57% of the total in 1988. Coal consumption at coke plants increased 13%, to 38 Mt (42 million st), from the level consumed in 1987. This increase reflects the recent recovery in the iron and steel industry. Metallurgical coal consumption in 1988 could have been greater. But US coke plants reportedly reached their maximum practical production capacity. As a result, net US coke imports amounted to 1.45 Mt (1.6 million st). Despite increased industrial activities, steam coal consumption by industrial plants was up only slightly from the 1987 level, amounting to 69 Mt (76 million st) in 1988. Residential and commercial coal consumption remained virtually unchanged at 6.4 Mt (7 million st). Coal exports and imports US coal exports rebounded in 1988, reaching 86 Mt (95 million st). It was the highest level of annual US coal exports since 1982, when they reached 96 Mt (106 million st). An unusual set of factors led to an opening for US coal exporters in 1988: • a high level of industrial production in Japan and the European Economic Community, • supply disruptions due to labor problems at coal mines in Poland and Australia, • a drought-related reduction in hydro-electric power generation in Canada, requiring increased coal-fired generation, • China's problems in meeting its export commitments, and • a fall in the value of the US dollar. US metallurgical coal exports in 1988 amounted to 56 Mt (62 million st), 9.1 Mt (10 million st) more than the 1987 level. Europe, Japan, and Canada were the principal importers of US metallurgical coal in 1988. European countries, in particu¬lar, increased their take by one-third of US metallurgical coal. The labor problems in Poland and Australia contributed to these higher levels of imports. So did increases in pig iron production of 8% in Japan and 9% in the European Economic Community. US steam coal exports - including bituminous, anthracite, and lignite-increase to 30 Mt (33 million st). This was up from 25.4 Mt (28 million st) in 1987 Contributing to this overall rise were 1.8-Mt (2-million st) increase in shipments to Canada and a 2.7-Mt (3-million st) increase to Europe. Unaffected by the somewhat tighter world coal market, US coal imports showed a slight increase to 1.8 Mt (million st) in 1988. Colombia continue to be the leading exporter to the United States, followed by Canada and Venezuela. Venezuela's entry into the US market is a relatively recent one, having made its first significant shipment in the fourth quarter of 1987.

Jan 1, 1989

By A. Singh

The control of flotation plants is by no means trivial. Flotation is one of the most interactive minerals? processing operations. The interactive nature of flotation circuits results in oscillations of levels and hence of grades and recoveries. Also, poor level setpoint tracking and disturbances have negative influences on grades and recoveries. The result is an unstable plant with limited scope for optimization. An advanced controller, FloatStarTM, has been developed to provide tight control and to reduce the amount of disturbances in flotation levels. It has been shown on a number of plants that the system results in faster and better setpoint tracking, better regulatory control and faster settling times after start-ups and disturbances. The successful stabilization provided by FloatStar has made it easier to investigate the area of optimization on flotation circuits. Mintek has identified the need for a more meaningful set of setpoints or aeration rates to use as a basis for control than levels and have advocated flow control by looking after residence times. When the feed conditions change, the ideal solution would be an algorithm or strategy that finds the new optimum conditions rather than just having an unguided hunt from the previous point. A multivariable flow-optimizing algorithm, a new module in FloatStar, has been developed to calculate optimum level setpoints and/or aeration rates that will aim to optimize the residence times, mass pulls and circulating loads within a flotation circuit. Keywords: flotation, regulatory, FloatStar, start-up, disturbance, residence times, circulating loads

Jan 1, 2003

By Rodney R. Krause

In attempting to tell the general public about the coal industry's land reclamation efforts, we have often said, "We're not doing things by the book, because we're still writing it." Like any good catchphrase, the statement is not only striking but true. It is particularly true in the mountains of Appalachia, where the problems of mining; and of reclamation are made more intense by the nature of the terrain. Mining and reclaiming the land "by the book' --which is to say by the methods of contour mining traditionally used in hill country--hasn't worked too well. So a lot of conscientious coal operators and associations are trying new methods--new ways of mining, new machines for seeding and planting, and new species to seed. Not all their experience can be transplanted to other areas, and of course I don't believe that Appalachia is the only place where new methods are being developed. Nevertheless, there's enough action in Appalachia to make a detailed examination rewarding, so let's focus on the hills to see what's new.

Jan 1, 1970

By Juan Francisco Mori, Miguel Ángel Aucapoma, Pablo Zevallos

En este artículo se describe el prototipo de un equipamiento instrumentado digital cuya función es monitorear la condición de los techos de los socavones para evitar que se produzcan accidentes por desprendimientos generados por el debilitamiento de las estructuras que sostienen los techos, debido al corrimiento de las estructuras del macizo rocoso. Básicamente el sistema informa mediante la activación de alarmas pre-configuradas al interior de mina, con el propósito de prevenir y evacuar al personal.

Apr 30, 2020

By Ygor Pereira de Lima, Iana Costa Carvalho, Marcelo Henrique Prado da Silva, Talita Gama de Sousa, Andrey Mariano dos Santos, Paulo Davi Borges Esteves, Rodolfo da Silva Teixeira, Andersan dos Santos Paula

Durante muitos anos, as ligas convencionais foram base para o desenvolvimento de novos materiais metálicos, com propriedades melhores que as até então conhecidas. No entanto, na última década, as Ligas de Alta Entropia (LAE) trazem uma nova abordagem para a produção de materiais avançados, com excelentes propriedades e potencial para diversas aplicações. Em particular, as ligas do sistema Al-Co-Cr-Fe-Ni também se destacam por promoverem uma classe de LAE de baixa densidade e têm sido foco de inúmeros estudos no meio acadêmico atual. O presente artigo traz um estudo de otimização da preparação metalográfica da liga AlCo2Cr2FeNi2, a partir de 3 rotas diferentes de polimento e suas análises via microscopia eletrônica de varredura (MEV) e difração de Raios X (DRX). Além disso, foram avaliadas as modificações estruturais da liga em função de um tratamento térmico de solubilização (1050 ºC por 1 hora seguido de resfriamento em água). Os resultados das análises demonstraram a rota de polimento eletrolítico promissora para a caracterização da LAE em questão e a análise conjunta dos resultados de DRX e MEV, somado ao confronto com a literatura, permitiram identificar as fases presentes e suas modificações microestruturais em função do tratamento térmico.

Oct 24, 2019

By Gusttavo Reis Leite Matos

Neste trabalho, a resistência à corrosão das ligas Ti-35Nb(0,0;0,5;1,0;1,5) Si e os metais puros, foram investigados em meio à saliva artificial fluoretada. Para tal, curvas de polarização, impedância eletroquímica, microscopia eletrônica de varredura (MEV), microscopia óptica (MO) e difração de raios-X (DRX) foram realizadas. O MEV e MO indicam que as amostras que contém Si apresentam maior ataque comparado aos metais puros. Esse fato foi confirmado através dos ensaios eletroquímicos onde foi possível observar que as ligas com a presença do Si apresentam menor resistência de polarização (Rp) e não passivam a superfície do material.

Oct 30, 2017

By Edney da Silva Dias, Leticia Fuchs, Walter Coan, Rodrigo Deperon, Eduardo Kuhl, Fernanda Jansen, Micael Leandro

O objetivo deste trabalho é apresentar um projeto desenvolvido para maximizar a taxa de ocupação dos veículos que carregam na ArcelorMittal Vega, por meio da utilização de programação linear combinada com métodos de automação de processos robóticos (RPA - Robotic Process Automation), de modo a atender todas as premissas do modelo de expedição de cargas, tais como: restrições de clientes, capacidade máxima por tipo de veículo e distribuição de volumes para as transportadoras de acordo com as metas acordadas. O uso de ferramentas de otimização e automação, integradas ao ERP (Sistema Integrado de Gestão Empresarial), utilizado pela empresa, permite realizar o processo de programação de transportes em massa, obedecendo multicritérios. A ausência de ferramentas que auxiliem neste processo, impacta diretamente na produtividade, na capacidade intelectual dos recursos alocados, na taxa de ocupação dos veículos, na capacidade de expedição da fábrica e no nível de serviço ao cliente. Visando aumentar a eficiência nos processos, melhorar a taxa de ocupação da capacidade dos veículos e consequentemente a capacidade de expedição, foi implementada a solução para aperfeiçoar o processo de programação de cargas e agregar valor ao negócio quanto a entrega ao cliente final.

Oct 1, 2019