Search Documents

By Jeanne A. Zimmer, Andrew B. Cecala, Edward D. Thimons

The Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the U. S. coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy-duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise in the future as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment, and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations. INTRODUCTION Face ignitions are a concern for many U. S. longwalls and will continue to be until better control technology can be developed or until reliable and accurate knowledge can be provided as to when an explosive concentration is present. Figure 1 shows the number of reported U. S. underground longwall ignitions from 1980 to 1990. The number of longwall panels have remained relatively constant over this time period with 89 reported in 1980, compared to 96 in 1990. In spite of technological improvements in mining over the past decade, no significant reduction in the number of longwall face ignitions has occurred. One factor contributing to this is that the U. S. coal industry is mining gassier seams causing methane liberation rates on the average to be higher (Trevits, 1991; Grau, 1987). Another factor is the development and implementation of more reliable, heavy-duty longwall face systems that are generating higher production rates and higher methane liberation rates. Additionally, the average panel width in 1991 was 714 ft; a 44 pct increase from 1980 when faces averaged a width of 495 ft (Merritt, 1992). Increases in panel width also impact total face methane emissions. [ ] There have been substantial advances in control technology in the areas of methane drainage, methane containment, and methane dilution. In some mines, efforts to drain methane in advance of mining have proven effective, but geological conditions often preclude this approach (McCall, 1984; Ely, 1989). In other cases, ventilation air quantities of over 100,000 ft3/min and face velocities of over 1,000 ft/min have been implemented on longwall panels. Other operations have implemented anti-ignition spray systems which use water sprays behind each cutting bit to quench the hot streaks created from cutting noncoal materials (Courtney, 1990). Other control techniques, such as the modified shearer clearer system and ventilated drum, have been used to increase the amount of turbulence and ventilation around the cutting drums, thus reducing methane levels (Cecala, 1986; Divers, 1987).

Jan 1, 1993

By A. B. Cecala

The US Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the US coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations.

Jan 1, 1995

By A. B. Cecala

The Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the U.S. coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy-duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise in the future as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment, and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations.

Jan 1, 1993

By Victor Rudenno

Cut-off grade is one of the most critical parameters affecting project cash flow. Its sensitivity is due to the number of other parameters that are correlated with any change in its value. Changes in cut-off grade, average grade and ore tonnage vary and they in turn can affect such parameters as capital and replacement costs, recovery, life of the project and operating costs. Perhaps one of the best definitions of cut-off grade is that of Taylor (1), "... any grade that, for any specific reason, is used to separate two courses of action, e.g. to mine or to leave, to mill or to dump ... . Obviously the most likely specific reason is one governed by economics, involving the return of investment and sufficient profit to motivate development and mining of the deposit. In this paper the cut-off grade is defined as that mining limit which will maximise the economic return for a projected mining venture. The following brief literature survey indicates that when computing the optimum cut-off grade there is a need to be able to directly compute the Discounted Cash Flow Rate of Return (DCFRR) or Net Present Value (NPV), as economically as possible, while allowing for parameter dependencies and variation in project structure.

Jan 1, 1979

By M. Yavuz

Due to workability difficulties, people have begun to use iron ore much later than gold, copper and bronze. In addition, iron and steel products are the most commonly used metals which are necessary for human life today. It is a fact that iron ore is raw material of the steel production process as known. Iron&Steel sector is plays an important role in the economic development of countries all over the world. Therefore, the amount of production and consumption of steel is one of the basic indicators of industrialization all over the world. The amount of steel consumed per capita of the country is considered as a measure of development. The world average per capita consumption of steel is around 210 kg in 2007 (Yildiz, 2009).

Jan 1, 2010

By S. Tuylu, D. Adiguzel, A. Bascetin, O. Ozdemir, U. Cinar

"In recent years, use of mineral processing tailings as a paste backfill has been significantly increased due to the environmental problems occurred during the disposal of the tailings in mine area. The paste material used to fill the stopes excavated is generally consisted of tailings (solid ratio: 70–85%) and cement (3-7%w/w). Meanwhile, the strength of the paste material is completely related to ratios of these materials. Cemented Paste Backfill (CPB) system is used as support depending on the roof pressure and also as an underground disposal method. Therefore, temporary strength value of the paste material gains a great importance. For example, the paste backfill material must compensate the minimum 4 MPa strength value in order to procure the permanent fortification, and the mixture cost must be minimal as well. For this reason, in this study, the Pb-Zn tailings were used to prepare for the paste backfill material using cement in order to perform the uniaxial compressive strength (UCS) tests. Additionally, a statistical experimental design and linear programming techniques was used to find the optimum mixture in terms of strength and cost. The pulp solid ratios (PSR) of the tailings and cement (by the solid) were varied as 75-85% and 3-8%, respectively. The results of this study; the optimum mixture is ~79.5%PSR and 6.8% cement ratio (by the solid) for 4 MPa UCS (28 day) and 16-17 cm slump value determined by this method with statistically reviewed experimental data. INTRODUCTION Fine-grained tailing waste materials resulting from mining activities are an important environmental problem. In terms of environmental protection, the use of tailings with paste backfill is a very attractive approach and a desirable solution to tailings management. Paste backfill, which is used to fill underground openings, is made by primarly mine tailings mixed with hydraulic binders and water. Its main benefits are not only disposal of mine tailings in underground, but also providing a certain strength to ensure a safe working environment. Therefore, it is necessary to use hydraulic binders due to durability of the system (Benzaazoua et al., 2004). Paste backfill, formed from the mix of dewatered plant tailings (75-85 wt. % solids), water and binder (3-8 wt. %) (Brackebusch, 1994; Landriault et al., 2005).Water is used to determine the chemical reactions between tailing and binder materials for strength as well as increasing pumpability. Portland cement and ash can be used as binder materials (Douglas and Malhotra, 1987). The factors which affect strength and stability of paste backfill separate into two groups called interior and exterior factors. Interior and exterior factors determine the strength, stability and deformation features of backfill in short and long terms and also affect the transportation of backfill to underground (Benzaazoua et al., 2004; Erçikdi et al., 2006; Yilmaz et al., 2010; Nasir and Fall, 2010). Material properties of tailings as well as site operations to fill the underground openings are the most important steps for the design purposes. Grain size distribution, chemical, and physical properties of tailings, and mechanical properties of paste fill material are used to understand the suitability of tailings as paste fill material (Ozturk et al., 2014). In addition, Fig. 1. is also proposed to apply a typical design for the operational stages of paste fill applications on the site."

Jan 1, 2016

By J. F. Archibald

It is often alleged by mine ventilation engineers that no reliable method exists to forecast the levels of radiation to be encountered in future uranium mines. It results that the design of uranium mine ventilation systems is based on factors other than radiological hazards, such as radon and radon daughter concentrations, for which permissible limits are set. Ventilation has been used to date as the main control mechanism for radon and radon daughters. Although it has become increasingly difficult to provide enough ventilating air to reduce the radon gas and its daughter products to safe levels in some mining arrangements, it is not the object of this paper to discuss alternatives to ventilation. This paper will describe a methodology followed by the authors over the years to estimate the levels of radiation to be encountered in underground and open pit uranium mines. Ventilating air is used to maintain working level concentrations within safe limits. The sources of radon and radon daughters and the quantities of each which will be produced, will be of great value in planning and designing a ventilation system to control them. This information can afterwards be integrated into the overall mine design. The methodology to be outlined can also be used to estimate, given a mine design format, the radiation levels to be encountered. If levels are not acceptable, modifications in the mine design can be made at an early stage. The emphasis is placed on an integrated effort where the ventilation engineers and the mine design engineers work in close collaboration from the very start of the mining project. Estimation of radon and radon daughter levels can be initiated as soon as core samples are obtained from the exploration programmes.

Jan 1, 1980

By N. Zouridakis

Radon is an established lung carcinogen and remains the most important environmental radiation exposure. It was estimated that inhalation of radon and its short-lived decay products accounts on average for about one half of the effective dose equivalent from all natural sources of radiation. Radon contained in household water can transferred into room air as a result of agitation or heating. An indoor air concentration of 400 Bq/m3 is obtained if the radon concentration in household water is 4 kBq/L. A typical concentration of radon in ground water is about 1000 times lower than this concentration but sometime elevated concentrations of some kBq/L in ground water are reported. In this work a Liquid Scintillation counting system is used to obtain fast and accurate measurements of radon (222Rn) in water samples from Argolida, Greece.

Jan 1, 2007

By R. Hogg

A standard procedure for determining size-specific gravity distributions of fine coal (including the -400 mesh fractions) by sieving and centrifugal sink-float separation is described. The significance of using a centrifugal sink-float technique and the effect of the magnitude of the centrifugal force on the separation of fine coal are confirmed in the present study. The relative merits of cumulative versus incremental sink-float are discussed. The procedure is evaluated quantitatively using data obtained for the products of froth flotation of -100 mesh coal.

Jan 1, 1994

By William Lodding

That grinding may change a crystalline material both in a physical and in a chemical sense has been shown by a number of authors in recent years. Thus Mackenzie (1) and Bartha (2) reported the effects of careful grinding on muscovite, quartz, gypsum, dolomite, etc. Increase in specific surface produced by grinding implies increase in total energy of a system. Newly produced surfaces are chemically more reactive; dislocations may be introduced during grinding, and existing strain may be released by the same process, as shown by Holt et el. (3) All these changes are easily detected by thermal analysis, but it is not easy to separate the multiplicity of effects registered and to arrive at quantitative interpretations. This paper is an attempt to analyze by the use of thermal analysis some effects produced in grinding. In differential thermal analysis (DTA) one measures all thermal changes occurring in a substance during heating or cooling. Chemical changes, such as decompositions, synthesis, oxidation, reduction, etc., and physical changes such as phase transformations, changes in specific surface and in thermal conductivity, strain release, etc. By thermo gradmetric analysis (TGA) on the other hand only chemical changes involving weight loss or gain are recorded. Similarly gas evolution analysis (GEA) will register only reactions involving gas evolution, including water vapor, and oxidation-reduction. By performing two or all three of these thermal methods of thermal analysis simultaneously and on the same specimen one can separate the different effects registered and by difference evaluate their magnitude.

Jan 1, 1966

By B. C. Haimson

The Committee on Rapid Excavation of the National Research Council has recognized in its 1968 report the need for "improvement of rock-mechanics techniques for measuring subsurface stress field in deep boreholes and for determining stress distribution in walls of underground excavations". The technique recommended in this paper as being most suitable for both deep hole and tunnel wall stress determination is Hydraulic Fracturing. Using this method stresses are calculated directly from the fluid pressures necessary to initiate and extend a fracture away from a borehole. Stress determination by hydraulic fracturing is rather insensitive to inhomogeneity or anisotropy, is not limited in depth except by the length of the hole, requires simple equipment which is commercially available, and can be carried out by unskilled personnel. The method has been worked out theoretically and extensively tested and verified in the laboratory. A number of field tests in deep holes ranging from 300 to 6300 ft have yielded surprisingly good results. Preliminary underground tests have been very encouraging and most recent measurements in a tunnel complex at the Nevada Test Site yielded stresses that were both consistent and reasonable when compared with the expected directionsand magnitudes. It is recommended that hydraulic fracturing be considered as a method of in-situ stress measurement both in the pre-excavation stage of design and during tunneling.

Jan 1, 1974

By M. Z. Rashad, H. A. El-Sageer

The intersections of numerous joint sets at the surface of tunnels of the Abu-Tartour project in Egypt create blocks of irregular shape and size in the rock mass. Although most of these blocks are unable to move into the free space of the tunnel, a few key blocks are capable of such movement. In addition, as soon as they move, some restrained blocks will be liberated. The aim of this work is to find the removable key blocks of the walls, floor, roof and corners of a portion of the tunnel under jointed surface rocks and then determine the best tunnel direction.

Jan 1, 1993

By R. A. Thomas, C. D. Litton

"The objective of this study was to develop a laboratory-scale method to rank the ignition and fire hazards of commonly used underground mine materials and to eliminate the need for expensive large-scale tests that are currently being used. A radiant panel apparatus was used to determine the relevant thermal characteristics of the materials: time to ignition, critical heat flux for ignition, heat of gasification, and mass loss rate. Three thermal parameters, TRP, TP1, and TP4, were derived from the data, then were developed and subsequently used to rank the combined ignition and fire hazards of the combustible materials from low hazard to high hazard. The results compared favorably with thermal and ignition hazards of similar materials reported in the literature and represent a simpler approach to quantifying these combustible hazards. INTRODUCTION The potential fire hazard from combustible mine materials is a major concern that can impact the safety of mine workers. Combustible materials tend to be solids and within this category there exist degrees of flammability and fire resistance. These materials may be readily ignitable or they may be able to withstand high temperatures and high heat fluxes. Presently, no simple methodology exists to assess these possible fire behaviors and quantify the resultant fire hazards. Thus, better knowledge of the thermal properties and chemical characteristics of combustible materials is of great importance to the safety of mine workers. Tewarson [1994] developed a methodology which he subsequently used to evaluate the ignition and fire resistant properties of combustible mine materials, but these efforts are more than 20 years old, and do not include many of the new materials used in mines today. The standard practice that has evolved for a combustible material to be approved by the Mine Safety and Health Administration for use in underground coal mines is to conduct extensive and costly large-scale experiments on each new material that is used in a particular mine operation. Results of such tests provide pass/fail answers to the questions of a material’s flammability or fire resistance, yet they provide little, if any, information that will lead to a better understanding of the basic mechanisms involved. Therefore, there is a need to quantify material flammability properties and to develop a methodology to rank the ignition and fire hazards of commonly used underground mine materials. During the heating and ignition stages of combustible materials, properties such as smolder susceptibility, minimum surface temperature for ignition, thermal conductivity, heat capacity, density, and heat of gasification are known to be important [Apte, 2006]. During the flaming stage, additional parameters, such as the heat of combustion, heat release rate, flame spread rate, yields of soot/smoke, and toxic gas production become more important as the flame is sustained and spreads. In very general terms, the heat flux incident on the surface of a solid combustible not only controls the rate of temperature increase of the local fuel surfaces, resulting in expulsion of fuel vapors that sustain the flaming process, but also the heating of other combustible surfaces that subsequently ignite and spread flame."

Jan 1, 2015

By R. A. Thomas, C. D. Litton

"The objective of this study was to develop a laboratory-scale method to rank the ignition and fire hazards of commonly used underground mine materials and to eliminate the need for the expensive large-scale tests that are currently being used. A radiant-panel apparatus was used to determine the materials’ relevant thermal characteristics: time to ignition, critical heat flux for ignition, heat of gasification, and mass-loss rate. Three thermal parameters, TRP, TP1 and TP4, were derived from the data, then developed and subsequently used to rank the combined ignition and fire hazards of the combustible materials from low hazard to high hazard. The results compared favorably with the thermal and ignition hazards of similar materials reported in the literature and support this approach as a simpler one for quantifying these combustible hazards. Resumen ¦ El objetivo de este estudio fue el desarrollo de un método a escala de laboratorio con el fin de clasificar los peligros de ignición y fuego de materiales comúnmente usados en minería subterránea y la eliminación las pruebas costosas y a gran escala que se realizan actualmente. Se usó un aparato de panel radiante con el fin de determinar las características térmicas relevantes de los materiales: tiempo de ignición, flujo de calor crítico para ignición, calor de gasificación y tasa de pérdida de masa. Se derivaron tres parámetros térmicos de los datos: TRP, TP1 y TP4, luego fueron desarrollados y subsecuentemente usados para clasificar los peligros combinados de ignición y fuego de materiales combustibles, de bajo riesgo a alto riesgo. Los resultados tuvieron una comparación favorable con los riesgo/peligro térmicos y de ignición de materiales similares reportados en la literatura y apoyan este enfoque como uno más simple para la cuantificación de estos riesgos combustibles"

Jan 1, 2015

By P. Creevy, P. F. Mousset-Jones, G. Danko, A. D. S. Gillies

The surface heat transfer coefficient is measure of the rate of heat transfer from exposed rock surfaces to the ventilating air. Knowledge of its value is of particular importance to accurately simulate the early stages of rock cooling after the opening of an excavation. A number of theoretical formulae for the calculation of the coefficient are available for use in mine climate simulation. However, direct determination by in situ measurement is preferred. Instrumentation, which has been developed for in situ mine measurement, and experimental procedures involving measurement at varying air velocities, are described. In a major study covering four Australian underground mines, the system has been used to determine surface heat transfer coefficients. A direct relationship was clearly established between the measured surface heat transfer coefficient and air velocity. Comparison is made between experimental results and those previously measured or calculated by others. The relationship established can be described by an equation and holds for air velocities above 0.4 mls. The derived relationship was con- firmed at all mines tested and is independent of geology and tunnel dimensions found in modern mines.

Jan 1, 1991

By A. Bruynesteyn

The results of a 2 phase evaluation program designed to determine the amenability of an oxide ore from the Butte, Montana mine of the Anaconda Company to a sulfuric acid leach is presented. In the phase 1 preliminary evaluation, using roll tests and percolation leaching in small columns, it is shown that the ore is highly extractable at low acid consumption ratios. In the phase 2 confirmatory tests in large columns on l-l.5 tons of material, the amenability of the ore to the leaching process is proven and pregnant solution grade profiles from planned commercial heaps established.

Jan 1, 1978

By G. Deschênes

Following a successful investigation on the Central Zone sample, a cyanidation study was conducted on an ore sample from the AD-MW Zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. At a grade of 6.48 g/t, gold is present in the forms of aurostibite, free gold and electrum. The ore contains 4.3% berthierite/gudmundite, 1.3% pyrrhotite, 0.7% pyrite, 0.07% stibnite and 0.9% arsenopyrite. Similar to the Central Zone, the extraction of gold from the AD-MW Zone can be performed at atmospheric pressure, pH 10.5 and with a low concentration of cyanide. The grind size had no effect on gold extraction between a P80 of 28 to 71 µm. The oxygen and cyanide requirement significantly increased with a ?ner grind. Consequently, a very close control of cyanide addition is required to minimize passivation of gold. Lead nitrate, added in the pretreatment, increased the extraction of gold by 2.3%. Leaching at pH < 10 improved gold extraction but increased the cyanide consumption by 5%. Passivation of gold occurred when the pretreatment was longer than 2 hours. A longer pretreatment reduced the cyanide consumption by 5%. Mineralogical characterization of the leach residue with no gravity pretreatment prior to leaching indicated the presence of unleached gold grains and passivated gold grains. Removal of coarse gold by gravity increased the extraction by 2.8% (leach residue at 0.74 g/t Au). Increasing the DO to 16 ppm or the lead nitrate from 500 to 1,000 g/t increased the overall gold extraction to 90.4% (leach residue at 0.62 g/t), which is the maximum gold extraction obtained. The leaching parameters were 800 ppm NaCN, DO 16 ppm and pH 10.5 for a duration of 120 hours. The associated cyanide consumption was 4.0 kg/t. Gold leaching was not sensitive to cyanide concentration. Reducing the cyanide concentration to 250 ppm resulted in a gold extraction of 89.5% with a cyanide consumption of 2.6 kg/t.

Jan 1, 2009

By Norman F. Schulz

The Davis magnetic tube concentrator is a laboratory machine designed to separate a small sample of pulverized magnetic iron ore into magnetic and non-magnetic fractions. It was developed in 1921 by mechanization of a test previously performed manually. (1)(2)(3)(1) No significant changes have been made in the design of the apparatus since that time. The Davis magnetic tube test continues to serve as a practical basis for judging the amenability of an ore to magnetic separation and for controlling magnetic separation plant operations. The apparatus consists of an inclined cylindrical glass tube supported adjacent to closely spaced pointed poles of a powerful C-magnet. (Figure 1). To conduct a tube test, a sample of a suitably prepared ore is poured into the water-filled tube. With wash water flowing through, the tube is oscillated to gradually reject the weakly magnetic ore particles until the desired degree of separation is attained. Both the magnetic concentrate and the tailings may be recovered for examination.

Jan 1, 1963

By Blagoj Golomeov, Boris Krstev

Nowadays, in the papers of authors in the area of flotation concentration, we can find several equations that describe the kinetics of flotation process as follows: Agar&apos;s equation, Klimpel&apos;s equation, Beloglazov&apos;s equation and Group of authors&apos; equation (equation with two kinetic constants). This paper makes an attempt to determine the most appropriate equation for mathematical interpretation of kinetics of the SASA mine rougher Pb - Zn flotation.

Jan 1, 2002

By S. K. Das

A detailed strata-mechanics investigation and examination was carried out in the E2 Panel (ML-II/7) of the XVI Bottom coal seam, which is located in the Moonidih Colliery of B.C.C.L., Jharia coalfield, India. Above this panel, the XVI Top coal seam was previously worked out by a longwall panel. Based on intensive field study and on experiments in a number of longwall panels located within various Indian coal mines, the actual behavior of the coal roof strata was evaluated and new strata-mechanics concepts around the longwall panels were developed. These concepts resulted in new methodologies concerning the behavior of roof rocks, caving characteristics, etc. within longwall panels and in the area of strata mechanics. Based on these new strata-mechanics concepts, a very simple, but realistic, model was developed to determine the optimum capacity of the powered supports. This model considered the combined loads resulting from the detachment of strata and composite layer blocks from the face and, also, loads due to the deflection of strata and composite layers situated above the detached roof rockmass. This formula, along with the other related formulas by the author, prompted the determination of the optimum capacity requirement for the powered supports to be used in the XVI Bottom coal seam, located under the worked out area. This new concept in strata mechanics and capacity requirements of the powered supports in a longwall face may be an aid to Mining Engineers.

Jan 1, 1997