Search Documents

By Henry T. Miller

INTRODUCTION The basic purpose of this paper is to suggest procedures and practices to insure that no employee working in a uranium milling operation receives exposure to radioactive, toxic, or other materials or agents that might produce a permanent, deleterious effect upon his physical health and well-being. This program is also designed to insure that each employee can carry out his assigned duties without risk to his health or to that of his fellow workers. The assumptions underlying this program are by necessity, conservative, with emphasis being placed upon prevention rather than correction or reaction to an undesirable situation. The limits specified-either as Threshold Limit Values (TLVs), Maximum Permissible Concentrations (MPCs), or Radiation Protection Guides (RPGs)--represent both standards of best practice and those of law and regulation. The total program is envisioned as a balanced combination of occupational hygiene and radiation monitoring. This includes surveying, air sampling, personnel dosimetry, bioassay, medical surveillance, epidemiology, and training--all backed by a thoroughly tested and evaluated set of emergency procedures. The program, as presented, is keyed to the results of monitoring, surveying, air sampling, medical surveillance, and epidemiology--it being obvious that no problem can result when no hazard can be identified. The lack of an identified hazard, however, does not negate the need for such a program and prudence suggests the need for routine surveillance programs in the best-designed facility. [The Model Mill] The model mill used in this paper is that presented by the U. S. Environmental Protection Agency in its study of the uranium fuel cycle1. The model mill processes 600,000 metric tons of ore per year into 1,140 metric tons of U308 as yellowcake per year using an acid leach process. Other characteristics of the mill such as location, tailings dam design, number of light water reactors supported, and geographical location are not pertinent to this paper. The usual remote western location of these facilities produce some difficulties in delivering the required occupational medical services and is not within the scope of this paper. The operating lifetime of most mills is commonly estimated as from 12 to 15 years in actual practice; however, the U. S. Environmental Protection Agency estimated a 20-year lifetime for its model. The principal steps in the acid leach process include :2 (a) Ore is blended and crushed to pass through a 2.5 cm (one inch) screen. The crushed ore is then wet ground in a rod or ball mill and is transferred as a slurry to leaching tanks. (b) The ore is contacted with sulfuric acid solution and an oxidizing reagent to leach uranium from the ore. The product liquor is pumped to the solvent-extraction circuit while the washed residues (tailings) are sent to the tailings pond or pile. (c) Solvent extraction is used to purify and concentrate the uranium. (d) The uranium is precipitated with ammonia and transferred as a slurry. (e) Thickening and centrifuging are used to separate the uranium concentrate from residual liquids. (f) The concentrate is calcined and pulverized. (g) The concentrate or yellowcake is packaged in 208 liter drums for shipment. This process is illustrated in Figure 1.3

Jan 1, 1981

By William F. Tanner

A river delivers a given load of sand, and hence of heavy minerals, into the sea into which it empties. This load is fixed by drainage basin characteristics and processes. Wave energy available for redistributing that load is fixed in an entirely different way. An equilibrium diagram of these two parameters (load versus energy) permits a tentative prediction of what will happen to the heavy minerals. The Chattahoochee River delivers a load which, over the past few thousand years, appears to have been greater than the available coastal energy could handle. As a result, much of the sand has been accumulated in various delta-margin features: barrier islands, beach ridges, and large furrowed off-shore shoals. The bulk of the trapped sand is found today in the shoals, which are attractive deposits for possible exploitation. If coastal energy levels are high enough to move the total load delivered by the river, accumulations of sand (and hence of heavy minerals) should be sought in the down-drift direction. Energy levels are rarely constant over any great length of coast. Decreases in energy may be due to widening of the shelf, convexity of, the shore, restrictions on the fetch, wave decay, or other causes. Such decreases result In deposition. Hydrodynamic mapping of coastal areas, as outlined here, should prove useful in the location of additional reserves. Part of this type of work can be done on maps, charts, and air photos.

Jan 1, 1962

By Mustafa Kumral, Samer Hmoud

Effective management of ore loss and dilution is essential for successful grade control and short-term mine planning due to their significant impact on the economic, environmental and technical aspects of openpit mining operations. Factors influencing ore loss and dilution fall into two categories: (1) controllable factors, like mine equipment selectivity and blast design, and (2) uncontrollable factors, such as spatial heterogeneity of ore and waste blocks on a bench. This paper focuses on the second category by applying spatial entropy concept to capture heterogeneity at the scale of selective mining units. In this paper, global spatial entropy is used to assess the impact of spatial heterogeneity between ore and waste blocks on the magnitude of ore loss and dilution, while the local spatial entropy can guide the allocation of blast movement monitoring balls preblast. High values of the global spatial entropy indicate increasing potential of ore loss and dilution, which reduce profit. Furthermore, through a number of case studies, the study investigates the relationship between spatial entropy, cutoff grades, blast movement, dig-limits optimization model running time, and profit. The results show that changes in cutoff grade and blast movement can significantly affect spatial entropy post-blasting and increase ore loss, dilution and profit reduction, revealing the need for controlled blasting at specific bench sections. Additionally, the results demonstrate an exponential increase in profit reduction due to ore loss and dilution with a rising global spatial entropy

Jun 1, 2024

By Marlin D. Schutte, Graham M. Fraser, Paul M. Kubera, Ronald J. Weetman

Mixers play an important function in the operation of multi-phase reactors in the minerals processing industry. They must suspend solids, transfer oxygen, maintain pH and temperature uniformity, assist in heat transfer, and, in biological processes, avoid the development of excessive shear rates. The LIGHTNIN A315 impeller (Figure 1) effectively supersedes the older Rushton turbine (Figure 2) which has been classically employed in gas­Iiquid-solids applications such as bacterial oxidation, cyanide destruction, etc. Since a stirred tank reactor can be such a key part of the overall process, it is essential that the mixers be designed for long term reliable operation, both process and mechanical, to insure a high percentage of on-line availability. Mixers in gas-liquid-solids processes may experience extraordinary loading conditions which must be taken into account to guarantee a robust mechanical design. Given the recent trend towards the design of world-class process units with maximum capacity equipment, there is increased importance and emphasis on the integrated design of the complete agitation system -mixer, vessel, and structure -to insure trouble free, post­commissioning performance. This paper presents some of the considerations necessary to specify the process functions of the mixer in multiphase applications, as well as special considerations for the mechanical design of the integrated reactor system.

Jan 1, 1993

By A. Nieto

A dump edge and vehicle proximity warning system is being developed at the Colorado School of Mines using GPS and wireless local area networks to improve the safety of off-highway trucks in open pit mines. After two years of research, software development, and testing in the laboratory, field tests are currently being carried out at operating limestone quarries and open pit mining operations to evaluate the effectiveness of the system under rugged operating conditions. This paper describes the progress made on this NIOSH-funded project and discuss, tests carried out recently, at the Morenci open pit copper mine in Arizona.

Jan 1, 2002

By Colin J. Douch

New Zealand has been a significant producer of gold for over a century. Total recorded production is over 850 tonnes. There were three major periods of production: the first and biggest was between 1860 and 1880, the second was between 1895 and 1920 and the third was between 1930 and 1945. After 1945 gold production fell continually until 1980 when the major upward adjustment in gold price led to renewed interest. There have been important new developments in each of the known gold-rich areas: Westland, Otago and Coromandel and exploration for gold in these areas and in previously unprospected regions has reached unprecedented levels. In Westland over 140 gold processing plants are each producing between two and six ounces a day from low-grade placers. A major gold dredging operation will soon be producing over a tonne of gold annually and other new dredges are proposed. There are still vast reserves of gold-bearing gravels in Westland and prospecting is continuing to reveal new resources. In the Reefton area there is renewed interest in gold-bearing quartz reefs which were the source of over a million ounces of gold between 1900 and 1951. New large opencast reserves are now defined.

Jan 1, 1988

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

Jan 1, 2001

Effective tools are not only essential for the design of practical and efficient underground mine ventilation systems but must also play an integral part in the operation of the mine. One such tool is VUMA-coal ventilation simulation software. VUMA-coal is Windows-based and has been specially designed for the simulation of underground coal mines and includes user-friendly coal specific interfaces and three-dimensional graphics designed to facilitate in the construction and analysis of networks. VUMA-coal can be utilised during the design phase of new collieries, be used to conduct ?what-if? and optimisation studies, and be integrated into the ?day-to-day? ventilation related operations. In addition, VUMA-coal can be used to simulate dust and gas distribution in a ventilation network, as well as predict the impact of control measures. This paper describes the interactive VUMA-coal ventilation simulation software and its underlying design features and outlines a case study of how VUMA-coal has been integrated into Anglo Coal?s Ventilation and Occupational Hygiene Engineering [VOHE] department as part of the standard planning and evaluation process in their operational mines as well as long term planning and future mining operations.

Jan 1, 2009

By B. Salopek, D. Rajkovic, D. Rumenjak

In decision making support system, that are used in various fields of environmental protection (environmental impact assessment, environmental management systems, setting environmental standards and regulation, etc.), it is often important to apply various mathematical environmental engineering models. The question of linking environmetal engineering modeling to decision making support system used in environmental protection is not yet methodically solved. The reasons for that could be manifold. Decison making support systems, used in environmental protection, because they are simply taken from bussines decision making, are not often adequate for specific problems raised in environmental protection. On the other hand, there are great number of types of models in environmental engineering, what urges the problem of finding the way of their proper linking with decision making support systems. The application of fuzzy logic in that field is estimated as one of possible solution of the problem.

Jan 1, 2005

By Tatiana Kotrikova, Steven Kolarz, Alan Kolodne, James Parkes, Matthew Goff

The WMATA Yellow Line is the section of steel segmentally lined tunnels that have experienced leakage and significant corrosion in isolated areas. A three part rehabilitation design has been developed for curtain grouting, structural repairs, and corrosion protection to provide continued performance. As WMATA’s first Construction-Manager-at-Risk (CMAR) project, the design development benefitted from collaboration with the Contractor through the final design development process. Rehabilitation work started in Fall 2022 and will be completed by late Spring 2023. Details of the project, the remediation design, and the process and benefits of the CMAR approach in the design development are presented.

Jun 13, 2023

By Jim M. Johnson

INTRODUCTION The facility water balance and maintenance of sufficient excess storage volume in the solution control system are often amongst the most critical facets of design and operation of heap leach facilities in cold, snowy climates. The purpose of this paper is to summarize and discuss climatic and operational factors which have a significant impact on heap leach water balance evaluations in high snowfall climates. Example water balance simulations are presented for proposed heap leach projects located in areas subject to high snowfall in the northwestern United States. The climatic data input to these simulations represent both net evaporative and net precipitation climates. FACTORS AFFECTING WATER BALANCE EVALUATIONS The combined effects of seasonal operations, re1atively low evaporative losses, and potentially large inflows to the solution control system from snowpack and spring storms require an enhanced awareness of the factors which impact facility water balance. Unlike operations at mines in more arid climates, seasonal excess water rather than a shortage of make-up water is the rule. A thorough understanding of a number of factors, including regulatory constraints, climatic influences, and impact of operating philosophy and techniques, is critical to successful development of an incident-free heap leach operation under high snowfall climatic conditions. A process water circuit schematic for a typical heap leach operation is shown on Figure 1.

Jan 1, 1988

By Robert A. Cortese, Carrie E. Lucci

Mine Safety and Health Administration (MSHA) regulations require underground coal mine operators to dust their mine corridors with an inert material to prevent coal dust explosions. The most commonly used material is pulverized limestone. Current practice to determine compliance with MSHA regulations requires the coal mine foreman or an MSHA inspector to collect samples of the deposited dust, a mixture of coal dust and limestone rock dust, for above ground laboratory analysis. To expedite this process, the U.S. Bureau of Mines has developed two instruments to facilitate the inspection and rock dusting processes, the explosibility meter and float dust deposition meter. The explosibility meter is a hand-held instrument which provides an in situ measurement of the explosible nature of homogeneous mine dust samples. The float dust deposition meter measures the mass loading density of the top layer of coal or limestone dust deposited on the mine floor during mining operations by the ventilation air. It may also be used to automate trickle rock dusting equipment. The operation of each device is based on the difference in the optical reflectance between the light limestone dust and the dark coal dust. The principal of the explosibility meter is based on the observation that, for a fixed coal volatility, the optical reflectance of dust mixtures is relatively constant at the limit of flammability, and independent of the coal dust particle size.

Jan 1, 1995

By Richard Meriwether Smith

Mining-related earthy bodies in contact with the atmosphere are now counted, generally, as minesoils. Because soils within this broad category are extremely young the influence of parent material is stronger than in older soils, where climate, organisms, and topography have had time to interact with near-surface rocks to form more distinctly differentiated profiles. Understanding of minesoil properties and processes is aided by definitions of rock types in terms of chemical, physical, and mineralogical characteristics that are, with some degree of consistency, translatable into soils. Geological correlations based on age or sedimentary sequences are helpful if they assure details of mineralogy and lithology, but our pedologic objectives demand that any conflicts involving rock types must be resolved in favor of distinctions having strongest implications for soil properties after mining. Chemically this approach emphasizes accounting of potential acid-base status, plant nutrient availability by adapted and calibrated extraction procedures, and absence of biotoxins. Physically it anticipates particle sizes, shapes, and arrangements in readily pervious soil profiles that will favor plant growth with desired levels of moisture and oxygen. Concurrently we are considering soil property suitability for uses other than growth of plants. Above all we need to be able to predict pedogenic processes in the particular environment, including rate as well as direction of chemical and physical change.

Jan 1, 1974

By Ronald G. Schmidt

AND SOME RIN UP HILL AND DOWN DALE, KNAPPING THE CHUCKY STANES TO PIECES WI' HAMMERS, LIKE SAE MANY ROAD MAKERS RUN DAFT. THEY SAY IT IS TO SEE HOW THE WARLD WAS MADE. Sir Walter Scott St. Ronan's Well - 1824 In the minds of many, geologic exploration has advanced little since the early nineteenth century. In truth, despite the development and refinement of new and potentially valuable technological tools, the approach or philosophy of the explorationist has received meager attention in professional literature. In many areas, the explorationist relies upon experience, subjective judgement and general intangible inspiration, often traveling together under the misleading pseudonym of "art," in achieving both an exploration plan and in making the myriad day to day decisions necessary to the execution of that plan. Without a solid, objective basis for decisions, exploration under this concept is little more than guesswork largely by intuition, and it is small wonder that many exploration programs flounder in a sea of over-expenditure inefficiency or fail to fulfill their expected goals within the funding which has been provided. From a rational management point of view, such a state of affairs is frustrating and inconsistent with the application of the same scientific principles which are presumed to be the basis for the exploration methods which are used. This somewhat presumptuous point of view cannot be extended as a general condemnation of the many exploration programs which are both technically and economically successful. On the other hand, the

Jan 1, 1968

By W. A. Hockings

This report describes a computer program for the solution of material balances in complex mineral processing flowsheets. The program, which is entitled MBS Metallurgical Balance System), evolved as the culmination of a series of material balance programs whose development began in 1967 at the Institute of Mineral Research, Michigan Technological University. The need for such a program became evident when the Institute became heavily involved in a large number of short-term pilot plant projects. Calculating material flows from analytical data by means of the standard two-product formulas grew increasingly difficult and time-consuming as the complexity of the flowsheets increased and as choices between conflicting analytical values had to be made. It was recognized that what was needed was a program that would assimilate all of the available data and calculate mass flow rates so that steady-state inputs and outputs would balance at each point in the flowsheet. Such a program should be capable of handling underdetermined, overdetermined and mixed systems, and when the given data are inconsistent, the program should adjust the data in such a manner that the adjustments are minimized. Missing analyses should also be calculated whenever possible. In addition to solving material balances, the program should be convenient to use and print out the results in a useful form. Thus, the inputting of data should be simple enough to be handled by relatively untrained personnel with diagnostic messages being printed out to identify errors and anamolous data when they occur. Most importantly, the program should produce well-formatted output which can be directly included into a report without the necessity of retyping. The proper spacing of table titles, column headings and the ability to control the columns being printed are important features in this respect.

Jan 1, 1977

By S. K. Kawatra, S. J. Ripke

Iron ore pellets use bentonite clay as binder at dosages from 0.5to 1.0% (10 to 20 pounds per ton) of moist iron ore concentrate. Bentonite is typically shipped hundreds of miles from Wyoming to the Lake Superior iron ore district. It is therefore best to know how effective a bentonite will be before it is shipped and used to bind concentrate into pellets. Current tests of bentonite effectiveness include: plate water absorption, methylene blue uptake, free swell, exchangeable cations, and glycolated layer expansion. However, these tests have many disadvantages: First, they only measure the ability of a bentonite to expand, disperse, or absorb, not how well it will bond. Second, most of the tests require up to 20 hours to perform. Bentonite only has a few minutes to interact within the concentrate before it is indurated (sintered). These long-term tests may not reflect the true behavior of bentonite. Third, the tests are tedious and often results are inconsistent between different iron ore concentrates, labs, and technicians. Fourth, some of the testing equipment is difficult to procure. Fifth, procedures are often difficult to standardize. In this paper, the Binder Effectiveness Strength (BESt) test to evaluate binders for iron ore pellets is presented that: measures the ability of bentonite to bond, requires only about two hours to complete, is simple and reproducible, and utilizes readily available equipment that has been standardized for decades.

Jan 1, 2003

By Dana S. Getman

For 30 years, mining operations worldwide have used diesel-powered mobile machinery to mechanize the mining process. South African diamond mines and some US coal mines have 15 years of experience with this type of equipment. During the past eight years, most of the new gold production from underground mines outside of South Africa has been mined by bulk methods using diesel-powered machinery. The underground mining industry, then, has secured and institutionalized the larger benefits created by a technology that was new to mining engineers in the early 1960s. The state of mechanized diesel-powered underground mining is now mature. To survive, though, mine operators -regardless of commodity mined and position in the commodity cycle-must maximize the benefits of diesel technology. The benefits gained in the next seven to 10 years will be realized by tweaking this component, fine tuning that piece of machinery and demanding optimum use of the technology. Manufacturers of diesel-powered machinery share the condition of maturity with their customers. Larger scale and easy market development have occurred. Much has been made of the potential size of the US coal segment as well as markets in China and the Confederation of Independent States (CIS). Indeed, opportunities do exist in these regions. However, these market development opportunities do not imply the market size trend line remains unchanged. They simply mean the potential market size is within reach. In fact, the market size for the product is shrinking.

Jan 1, 1993

By K. Kim

A site characterization strategy formulated for the probabilistic design of underground structures is presented, which takes into account the variability of rock properties and the stochastic nature of the rock failure process. It entails determining probability distributions of rock properties by utilizing the theory of extremes and Monte Carlo simulation. Laboratory and field test data are analyzed and presented to illustrate the methodology. The results indicate that the distributive characteristics of rock mass properties can be estimated using empirical relationships currently available. This results of analyses can be incorporated into the design of underground structures, and then, the relative uncertainties of the failure probability of the structures can be assessed.

Jan 1, 1995

By Brett P. Spigarelli

"To meet the growing need for CO2 capture and storage technology, Michigan Technological University is studying CO2 capture using alkali-based solvents. The objective of the present study was to find a way to increase the absorption rate of CO2 into an alkali solution without reducing the absorption capacity of the solution. One approach to increasing absorption rate is to use a surfactant to chemically alter the gas bubble size. The surfactant chosen for the study was a neutral-charge polypropylene glycol methyl ether (PPGME) with a molecular weight of 200. Experiments were conducted to study the absorption rate of CO2 at varying surfactant concentrations. Results showed that as the concentration of PPGME increased in solution, the absorption rate also increased. The CO2 absorption rate increased from 3.45 x 10-3 mol/min CO2 at 0g/L PPGME to 3.92 x 10-3 mol/min CO2 at 0.48 g/L PPGME. This amounted to a 14% increase in the CO2 absorption rate with no decrease in the absorption capacity of the solution. IntroductionChemical absorption using an amine solvent is currently the most mature carbon capture and storage technology available. Amines are advantageous in that they have a fast CO2 absorption rate, which leads to a high CO2 removal efficiency. However, amine absorption has some considerable drawbacks, such as high energy requirements, high equipment corrosion rates, amine degradation in the presence of oxygen, high waste generation and a large increase in plant footprint if new equipment is constructed (Herzog and Golomb, 2004; D’Alessandro et al., 2010). Due to these drawbacks, Michigan Technological University (MTU) is studying CO2 absorption using alkali-based solvents, which address the above disadvantages of amine solvents."

Jan 1, 2015

By Paul E. Senseny

Data from triaxial compression tests per- formed at confining pressures between 0 and 100 MPa are used to evaluate parameters in a contitutive model that is based on microcracking. The tensorial formulation is reduced to equations that are specific to the simple Loading imposed in triaxial compression tests. Procedures for evaluating the model parameters are described, dependence of parameter values on confining pressure is discussed, and prediction of failure is assessed.

Jan 1, 1986