Search Documents

By Maria D. Salazar-Villalpando, Anthony Cugini, Bryan Reyes

"The electrochemical reduction of CO2 was performed in a laboratory-made, divided Htype cell. A copper electrode was used as the cathode. An Aldrich Nafion 117-type ion exchange membrane (0.18mm thickness) was used as the diaphragm. NaHCO3 and KHCO3 were studied as the catholytes. Hydrogen evolution from water reduction and products from CO2 electrochemical conversion were recorded. Higher CO2 reduction enhancement was observed by KHCO3 as compared to NaHCO3. The main conclusion of this work is that in fact CO2 can be electrochemically reduced with copper electrodes.1.-INTRODUCTIONThe direct electrochemical reduction of CO2 may allow for a simple process and, by avoiding high temperature reactors, would enable the process production rate to be quickly varied to follow the time of day availability of surplus electricity [1]. Temperature has a major effect on the electrochemical conversion of CO2 since its solubility increases when temperature decreases [2]. The electrical potential applied to the electrochemical reacting system will have an influence on the product distribution, as well. For example, a narrow potential range during cyclo-voltagraphic studies will determine the detection of a lower number of products. A recommended potential range to study the electrochemical reduction of CO2 is -2V to 2V. Moreover, the reaction rate on the electrode is governed by various processes, such as the kinetics of electron transfer, adsorption/desorption at the electrode surface, and diffusion of CO2 to the Cu electrode. The availability of active species, CO2 for electro-reduction, is extremely low at the vicinity of the electrode surface and it seriously interferes with the rate of mass transfer. In batch type electrolytic reactors, depletion of CO2 at the surface takes place first. CO2 from the bulk then has to diffuse to the electrode surface, resulting in mass transfer controlled kinetic phenomena. During the above process, several other competitive side reactions could suppress the primary reaction even though the cathode has good electro catalytic properties for reduction of carbon dioxide. When the dynamic supply of specific active species is ensured to electrode surface, the mass transfer effects are minimized to certain extent. Hence it is envisaged that a continuous flow reactor is more efficient for the electro-reduction of CO2 in CO2 saturated aqueous electrolytes. The primary reactions that occur at the copper electrode during the reduction of CO2 are listed below (with the standard potentials calculated using formation energies [1] :"

Jan 1, 2010

By Xuewei Lv, Maojun Zhou, Xiaobo Huang, Rende Zhang

"The characterization of the surface roughness of the mineral particles is of vital importance for the studies of the mineral processing. In this study, an evaluation of the roughness of the iron ore particles, with the measurements of size distribution and the measurements of specific surface area with the liquid nitrogen absorption, was developed. The main theory of this method is the fact that the roughness of the particle influences the specific surface area apparently. The specific surface area of the particles can be measured with the laser diffraction method and the liquid nitrogen absorption method. The influence of the surface roughness of the particle can be measured with the nitrogen absorption and cannot be measured with the laser diffraction. Therefore, the roughness can be got by comparing the specific surface area with two measurement methods.IntroductionThe characterization of the surface roughness of the mineral particles is of vital importance for the studies of the mineral processing. There are three main methods for measuring the size distribution of mineral particles: sieving, laser diffraction, and sedimentationl). Many techniques involve sedimentation such as the Horiba2, 3) and the Cyclo-sizer1). In the mineral industry, size distribution is usually determined by sieving because it can be carried out accurately for all particle sizes larger than 45 . The preferred method to obtain the size distribution of finer particles is laser diffractometry. The technique has several advantages: it produces measurements in a few minutes with considerably less labor compared with the cyclo-sizer and for a range of sizes considerably wider in comparison with the sedigraph4). The equivalent-sphere size distribution reported by laser diffractometry is valid for metallurgical calculations and can be routinely used in mineral processing plants. The surface area of the particles can be measured by the BET method of nitrogen adsorption, or it can be calculated from the size distribution. However, the latter calculation requires the size distribution to be accurately known across the whole size range, and assumptions have to be made about the shapes and surface roughness of the particles and presence or absence of pores (see below). The BET method is based on the physical adsorption of gas over the whole exposed surface area and measures the surface area stemming from the roughness and open pores on the surface of the particle5). The calculation of the surface area from the size distribution is usually based on the assumption that all the particles are smooth spheres, without considering the shape and/or roughness of the particles. Determining the surface roughness of the particle with these methods, is the objective of this study."

Jan 1, 2012

By A. Slotwinski, R. E. Barry, M. M. Menon, P. T. Spampinato

"A coherent FM laser radar based sensor for remote metrology of plasma facing material surfaces in a fusion reactor is described. The sensor is capable of 3-D mapping of surfaces, based on a series of precise range measurements from large distances (up to 20 m). Other features include the ability to operate under adverse environmental conditions involving very high gamma radiation (3xI04 Gy/hr), ultra-high-vacuum (<I0-5 Pa), and high temperature (200°C). The paper describes the basic principles of the sensor, together with experimental results obtained with the sensor. The ability of the sensor for remote rendering of ""visual quality"" images without the need for any external illumination is also illustrated.IntroductionMeasurement of the features of large area surfaces (-1500 m2) to sub-millimeter accuracy, from relatively large distances (20 m), is necessary in the case of the International Thermonuclear Experimental Reactor (ITER -a 1500 MW fusion reactor that is currently in the design phase). Furthermore, the measurements may have to be performed after the reactor is temporarily shut down. During such shut-downs, the ITER in-vessel environment will be highly radioactive due to neutron activation of the reactor wall (gamma radiation field of 3xl04 Gy/hr), the vessel will be maintained under ultra-clean vacuum conditions (<10-5 Pa), and the plasma facing surfaces will be maintained at elevated temperature (200°C). Therefore, the precision measurements must be conducted remotely, and because of the large dimensions of the fusion reactor and the limited number of access ports, the measurements must be done from large distances. The reactor vessel is a large toroid. Fig. 1 shows the cross section of the toroidal vacuum vessel, and the location of the metrology probe. Because of the very large surface area involved, fast scanning capability is also needed to reduce the reactor down-time."

Jan 1, 1997

By Ko-ichiro Ohno

It is recently recognized that the iron reduction and melting as well as the slag separation of a composite of granular iron ore and coal are completed in a very short period of about IO minutes when the composite is rapidly heated up to approximately 1673K. These phenomena are expected to be applied to a new iron-making process. The mechanism of iron ore reduction and iron-slag separation during rapid heating has not yet been revealed and the fundamental research has just started. Carburization of the reduced iron is regarded as one of the most important steps in this process. In the present work, the composite was prepared from four kinds of coal or graphite as a carbon source and electrolytic iron powder as a completely reduced iron ore. The temperature at which the liquid formation and iron carburization occurred was monitored. Direct observation of smelting reduction behavior was made by a confocal laser-scanning microscope combined with the infrared image-heating furnace to clarify the effect of molten ash on iron carburization. It was found that the meltdown temperature of composite became lower as the melting temperature of coal ash decreased. From the observed result, it was presumed that the liquid slag would act as an important media for the carbon transfer from coal to iron. The carburization mechanism during the smelting reduction was estimated as follows. When slag containing iron oxide melted down and contacted carbon, iron oxide in the slag was reduced and the formation of the metallic iron particle as well as the its carburization occurred simultaneously at the slag-carbon interface. Carburized iron particle was carried from slag- carbon to slag-iron interfaces due to the slag convection flow caused by the difference of the interfacial tension between the carbon-slag and iron-slag interfaces. Carburization of reduced iron could proceed with a repeat of the above-mentioned process.

Jan 1, 2003

By Ko-ichiro Ohno

It is recently recognized that the iron reduction and melting as well as the slag separation of a composite of granular iron ore and coal are completed in a very short period of about 10 minutes when the composite is rapidly heated up to approximately 1673K. These phenomena are expected to be applied to a new iron-making process. The mechanism of iron ore reduction and iron-slag separation during rapid heating has not yet been revealed and the fundamental research has just started. Carburization of the reduced iron is regarded as one of the most important steps in this process. In the present work, the composite was prepared from four kinds of coal or graphite as a carbon source and electrolytic iron powder as a completely reduced iron ore. The temperature at which the liquid formation and iron carburization occurred was monitored. Direct observation of smelting reduction behavior was made by a confocal laser-scanning microscope combined with the infrared image-heating furnace to clarify the effect of molten ash on iron carburization. It was found that the meltdown temperature of composite became lower as the melting temperature of coal ash decreased. From the observed result, it was presumed that the liquid slag would act as an important media for the carbon transfer from coal to iron. The carburization mechanism during the smelting reduction was estimated as follows. When slag containing iron oxide melted down and contacted carbon, iron oxide in the slag was reduced and the formation of the metallic iron particle as well as the its carburization occurred simultaneously at the slag-carbon interface. Carburized iron particle was carried from slag-carbon to slag-iron interfaces due to the slag convection flow caused by the difference of the interfacial tension between the carbon-slag and iron-slag interfaces. Carburization of reduced iron could proceed with a repeat of the above-mentioned process.

Jan 1, 2003

By Huyang Xie, Rishi Raj, Vera A. Versteeg

"A new method for MOCVD has been developed in which a precursor solution is directly injected into a reaction chamber. The vaporization of short pulses of liquid is facilitated by atomization with a piezoelectrically-operated nozzle. The system has been used successfully to grow oriented, thin Ti02 (rutile) films on sapphire substrates with the crystalline relationship (101)[010]R I (1120)[0001]s. A growth rate of approximately 2 monolayers per pulse was achieved at 650°C for a reactant impingement rate of about 800 monolayers per pulse. Also, epitaxial LiTaO3 thin films were grown on (0001) sapphire from a single source, bimetallic precursor, lithium tantalum hexa-t-butoxide as the precursor. X-ray diffraction shows that the LiTaOa c-axis is normal to the sapphire surface. The x-ray pole figure and crosssection TEM diffraction show that the films were also in-plane oriented, with sapphire [1010] parallel to lithium tantalate [1010]. These films are shown to have extremely low optical attenuation, and refractive index that compares well with bulk values.IntroductionMetalorganic chemical vapor deposition (MOCVD) techniques have come into increasing use in recent years, due to the growing versatility and availability of precursors and improved environmental advantages over the halogenated compounds used for conventional CVD. Most commonly, the films are deposited by dissolving the metalorganic reactant (typically a metal alkoxide) in a carrier gas, which is carried through heated lines to a heated substratel . The metal alkoxides decompose by pyrolysis, leaving the films on substrates. While this method has been used to produce excellent epitaxial and heterepitaxial films, it has the disadvantages of complexity: the precursor must be heated to fix its vapor pressure, the gas flow rate carefully controlled, and the carrier lines heated to prevent condensation before reaching the reactor. Additionally, this conventional method cannot be used with certain low-volatility precursors that decompose upon heating."

Jan 1, 1994

By Hideharu Fukunaga, Jin Pan

"The recognition of Metal Matrix Composites (MMCs) as a means of providing high specific strength, high specific stiffness, excellent wear resistance, low thermal expansion and improved high temperature properties has led to a number of new processing, not previously used for plastic and ceramic matrix composites. As a primary fabricating process, the liquid methods are the major ones, which are reviewed briefly from the view of processing terminology. One of them, squeeze casting process is the most traditional and well-developed, because it is rapid, versatile and near-net shape production of materials. Two of new squeeze casting processes are presented to offer the hardness· controlled MMC and the· functionally graded MMCs as well as a newly developed whisker preform.I .IntroductionA large number of liquid processes and techniques including semi-solid liquid process are proposed. The most primitive process is ''pressure infiltration casting” of liquid metal into the fiber preform. It is called as follows depending on pressure and its source squeeze casting (1-4) by hydraulic ram, gas pressure infiltration casting (5, 6), vacuum infiltration, centrifugal casting (7), Lorentz-force-driven infiltration (8). The pressurizing on the liquid metal requests a large and stiff equipment, so pressureless infiltration technique has been developed using K2ZrF6 flux (9,10) while the mechanical properties are not high enough, and using H2 gas with Mg alloying element called pressureless infiltration casting (11-13), spontaneous infiltration process (14) and PRIMEX (15). In those processes, no severe reaction occurred between the reinforcement and matrix molten metal. In early l 990's, the reactive processing with pressure or without pressure, in which one material is totally transformed into another of the required shape, eq. assisted oxidation, has been developed, called reaction squeeze casting (16,17), DIMOX (18) reactive infiltration casting (19,20), and in-situ process (21,22). Die casting of SiCp/Al alloy (23,24) and thixocasting of SiCp/Mg alloy (25) are also applied to produce the machine component of MMCs."

Jan 1, 2000

By Lijuan Li, Zheng Lu, Xin Xia, Qijie Zhai, Qingchun Li

"Pulsed current and pulsed magnetic field have been applied to the bainite transformation of Cr5 steel. Three groups of experiments were conducted. In the first group, ordinary resistance furnace was used for heat treatment. The Cr5 specimens were rapidly heated up to austenitization temperature 940 °C, held for 20 min, air cooled to bainite transformation temperature 350 °C, held for 10, 20, or 40 min and then air cooled to room temperature. The second and the third group shared the same temperature-time curve with that of the first group, but their heat resources came from the Joule heat produced by pulsed current. 1.5 T pulsed magnetic field was exerted on the third group specimens when they were held at 350 °C, but the second group specimens did not undergo the treatment of magnetic field. It was found that both pulsed current and pulsed magnetic field obviously retarded the bainite transformation. The phenomena were discussed in terms ofliterature results.IntroductionApplying pulsed current and pulsed magnetic field technology are very pronnsmg ways to change the microstructure of materials by affecting the phase transformation process. People had found that pulsed current dramatically influences the behaviors of materials, for example, electromigration effect [l], the solidification of metals and alloys [2, 3], electroplasticity [4, 5], crystallization of amorphous alloys [6], healing of metal materials [7] and so on. As to pulsed magnetic field technology, a lot of effort had been spent on grain refinement in solidification of metals [8, 9], recrystallization of cold-worked metals and alloys [10] and Fe-based alloys solid-state phase transformation [11, 12]. Though application of pulsed current and pulsed magnetic field technology have proliferated in recent years, investigation on their effects on solid/solid phase transformation, especially bainite transformation, is lacking. The aim of this paper is to show the effects of pulsed current treatment (C-T) and the combined treatment of pulsed current and pulsed magnetic field (CM-T) on bainite transformation of commercial Cr5 steel"

Jan 1, 2014

By Knut H. Bech, Stein Tore Johansen

"The collision efficiency for small particles relative to 2D spherical bubbles in a developed turbulent flow field were calculated applying an adopted version of the CPD program FLUENT. The turbulence field was related to bubble size and fluid properties. The results were compared with analytical theory. The turbulence intensity was found to be the most important single parameter for collision efficiency. Effects of boundary layer thickness and particle diameter were discussed. IntroductionRemoval of inclusion particles from melted aluminium can be facilitated by means of a rotor system that supplies kinetic energy and gas bubbles to the floating metal. At the surface the inclusions adhere to the surface dross or slagg which is removed at regular intervals by the operators. When applying computational fluid dynamics (CFD) to model such a system, one experiences difficulties with the large range of turbulent length-scales encountered, from the large geometrical scales of the rotor and container, through the bubble size and down to the particle diameter. A mathematical model for the complete system will be both complex and require an extreme spatial resolution. Another way of dealing with the problem is to model the micro-scale phenomena separately and apply the results to create a model for the macroscopic system. In a previous work [12] we addressed these problems and developed a procedure for calculating turbulence enhanced flotation to bubbles. It was found that turbulence may have a profound effect on the collision rate of particles to idealized bubbles. In this study we recognize that only a fraction of the total turbulent kinetic energy generated by the rotor's work on the liquid metal may contribute to enhanced flotation. By using a model spectrum for the turbulence, the fraction of turbulent energy in eddies smaller than the bubble diameter is calculated. A twodimensional CFD model was then constructed to calculate the collision efficiency between particles and bubbles of various sizes."

Jan 1, 1999

By Tatiana Pereira Moreno, Priscilla Aki Mori de Hanashiro, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Hugo Hashimoto

"Nowadays, End-of-Life (EoL) Liquid Crystal Displays (LCDs) are traditionally disposed in landfills. The increasing access to LCD technology over the last years by Brazilian consumers has intensified LCD' s disposal as an environmental and economic issue. This study aims to characterize used LCDs to identify the main components for recycling. Characterization was performed through scrap disassembly and its components were identified, separated, and weighted. LCDs were disassembled and the following divisions were applied: screen, metal frame, polymeric frame, polymeric sheets and electronic part. Some techniques were used to determine the concentration of Indium in the LCD, the glass/plastic ratio and the different kinds of polymers that compose the screen. The techniques used for characterization included inductively coupled plasma optical emission spectrometry (ICP-OES), Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). This method, when applied to a wide range of LCDs, can allow the development or improvement of an EoL management of LCD.IntroductionWaste Electrical Electronic Equipments (WEEEs) are waste from discarded equipment, such as computers, monitors and cellphones [1]. Over the past years, treatment of WEEE has been emphasized. It occurs due to the technology's advancement that leads to an even larger increase of WEEES [2].Among WEEEs, there are the liquid crystal displays (LCD). LCD technology is applied in cell phones, tablets, computers and monitors. Nowadays, it's the most well known technology when it refers to monitors, due to its advantages over the Cathode Ray Tube (CRT) technology. Some of them are energy saving, smaller size and no radiation emission [3].This feature in the LCD's global market along with the speed at which electronic equipment becomes obsolete affects society economically and ambiently.This issue becomes even more serious when considering the final destination of the liquid crystal displays. LCDs are lead to landfills as other WEEEs. Besides the different materials long degradation time, the environment is damaged by the disposal of the potentially reusable and hazardous materials [ 4]."

Jan 1, 2014

By Vadym Drozd, Yongzhou Sun, Shah Najiba, Jiuhua Chen, Andriy Durygin

"Phase transitions of the potential hydrogen storage compound, ammonia borane (NH3.BH3), was investigated using Raman spectroscopy and a diamond anvil cell at high pressures up to 9.5 GPa and low temperatures down to 90K. At room temperature, ammonia borane has three phase transitions in this pressure range. Upon cooling, four new phases were discovered through changes in characteristic Raman spectra. This result provides information about the stability of new bonding characteristics of this potential hydrogen storage material at low temperature and high pressure region.IntroductionDevelopment of hydrogen technology requires the safe, efficient and environmental friendly materials for hydrogen storage and hydrides have attracted much attention as hydrogen storage media. Among chemical hydrides, ammonia borane (BH3NH3) stands out due to its high gravimetric and volumetric hydrogen density ' "". Despite high hydrogen content, this compound is very stable. It releases hydrogen in several steps by thermal decomposition in the temperature range of 100°C to 500°C. Direct thermal decomposition also causes toxic borazine emission. Recent research interests on ammonia borane include destabilizing this compound to lower the dehydrogenation temperature with an enhanced hydrogen release rate using different techniques, e.g. the nanoscaffolds'', ionic liquids"" and acid'"" or transition metal catalysts' ""'. As a molecule of ammonia borane consists of protonic (NH) and hydritic (BH) hydrogens bonded by the polarized dative bond, thermal or catalyzed decomposition requires breaking of N-H and B-H bonding. Still now, the detailed information about the bonding characteristics of ammonia borane is not sufficient to understand details about its phases and structures. The development of methods to enhance hydrogen discharge rate from ammonia borane requires a detailed study about the structural and dynamical properties that control the stability and the intermolecular interactions of this material. This study is motivated to investigate the stability of the existing phases and also to explore the existence of any new phases at different temperatures and pressures which may have enhanced hydrogen release and uptake properties."

Jan 1, 2012

By Guangchun Yao, Chuan Li, Hongjie Luo, Zhuokun Cao

"The expansion rate and collapse time of liquid aluminum foams are essential for the determination of operating time and quality of the resulting foam. In the present paper, liquid aluminum foams was fabricated by adding in TiH2 as blowing agent, and the variation of expansion rate with foaming time was non-contact detected by a laser distance measurer. The influence of different stabilizing agent and alloying elements was studied. The results show the fact that the fraction of stabilizing agent only perform little effects on the maximum expansion rate of liquid aluminum foams, while the influence of alloy elements are remarkable. The maximum expansion rate would increase much when Mg is added, and the liquid foam also collapse at a shorter time. Comparison was made between experimental results and mathematic calculations, which reveal the fact that it is the change of TiH2 decomposition responsible for the change.IntroductionMetal foams, combining light weight with other unique mechanical and physical properties, have gained wide interest and been developing fast during past few decades. However, manufacture of this new material is quite challenging since it involves simultaneous occurrence of gas, liquid and solid phase at high temperature [1-2].Quite some manufacture routes have been developed for manufacturing metal foams, and the structure and quality of resulting foam are remarkably improved during the last decades. However, most of the past works seems to be experiential, and because the lack of basic knowledge of foaming process, the start material is limited and the production technologies are far from reliable and reproducible.[3-4]In direct foaming process, decomposition of blowing agents, TiH2 for example, is the main force for foam expansion. The density and foam structure changes with time during the foaming process, so it is expected that foams of certain structure can be obtained by solidification of the liquid foam at a certain time [5-6]. However, the foaming process is weak in reproducibility and the influence of stabilization additives and alloying elements is unclear."

Jan 1, 2011

By Georgeta Rata, Cornelia Petroman, Ioan Petroman

"Proper training and education in the field of recycling and waste treatment are inconceivable without the proper teaching of the terminology specific to both recycling (aerospace products recycling, automotive recycling, general recycling, recycling behaviour, recycling schemes, recycling systems, and waste recycling) and waste (characterization of waste, electronic waste, heavy-metal containing waste, monitoring of waste, radioactive waste, solid waste, waste collection, waste conversion, waste recycling, waste reutilization, waste stabilization, waste storage, and waste treatment) in both the students’ mother tongue and in English for Special Purposes (ESP) as a second language (with focus on the structuring of the specific terminology). Including linguistic approaches among the possible approaches of environmental protection and material sustainability means including linguistics among the various disciplines addressing energy supply, cement and building materials, metallurgy, chemistry, glassware, pulp and paper industry, machinery, automobile and electronic industries, collection, and sorting, further treatment and final disposal of post-consumer material.IntroductionCultural and technical changes have produced more novel artefacts than novel activities or novel properties, generating new vocabulary needs that are readily answered by new words (nouns).The purpose of this research is to show that ‘waste words’ – phrasal words (items that have the internal structure of phrases but function syntactically as words, e.g., cattle waste) and particularly compound nouns (words formed by combining roots, that tend to have a meaning that is more or less idiosyncratic or unpredictable, e.g., wastepaper ‘discarded paper’) – used in the study of the English of recycling, waste treatment, and clean technologies can be misleading for both native and non-native students and/or users of English because their structure alone does not allow instant, proper understanding of their meaning.Our hypothesis is that this inconvenient can be overcome by getting to reach the proper meaning of these new words. Or, arriving at the precise meanings of the ‘waste words’ depends on our knowledge of the world (for example, wastepaper indicates that some used paper is discarded and not wasted) rather than on purely linguistic knowledge."

Jan 1, 2008

By Zhu Fangyi

"The article introduces the process EAF with De-P hot metal charging for Melting Stainless Steel in Baosteel stainless steel Branch. Based on the practice of production, the main effect on the Cr Loss during EAF with De-P Hot Metal Charging Melting Stainless Steel including using oxygen, the material charging and making slag are theoretically analyzed. The optimization of using oxygen can reduce the oxidation of Cr during EAF Melting Stainless Steel. The optimization of material charging, especially Si content is suitable can reduce the loss of Cr. Effective reduction can realize the lowest Cr oxide in slag. Based on the character of the process EAF with De-P hot metal charging for Melting Stainless Steel, applied the integrated control method, the Cr loss during EAF melting stainless steel decreased 43.10%. 1 INTRODUCTION EAF with De-P HM charging for melting stainless steel is a technology for stainless steel making. Practice prove that the new process can shorten tap to tap time, reduce the special power consumption, dilute the impurity element from the stainless steel scrap that is propitious to produce the high quality stainless steel, alleviate the shortage of stainless steel scrap to the production. As a new technology, the process has some technical problems and difficulties. The proportion of Cr alloy charging exceeds 20% during EAF with De-P hot metal charging melting stainless steel. As Cr alloy is difficult melting and easy oxidation, too much Cr alloy charging result in Cr loss too much and tap to tap time too long for EAF production. By applying the new technology, Baosteel stainless steel branch has increased the technology level and economy index. Now the content of Cr oxide in slag reduce from 8.59% to less than 6.0%. The Cr loss during EAF melting stainless steel decreased 43.10%. According to the practice application, the process of EAF with De-P HM melting stainless steel are theoretically analyzed. The main factors affecting the Cr loss during EAF with De-P hot metal charging melting stainless steel are discussed."

Jan 1, 2008

By E. Gratz, U. Pal, A. Powell, S. Pati, J. Milshtein

"The solid oxide membrane (SOM) process has been used at 1150 'C to produce magnesium by direct electrolysis of its oxide. Magnesium oxide is dissolved in a molten CaF2-MgF2 ionic flux. An oxygen-ion-conducting yttria-stabilized zirconia (YSZ) SOM membrane separates the cathode and the flux from the anode. During electrolysis, magnesium ions are reduced at the cathode and Mg(g) bubbles out of the flux into a separate condenser. The flux has a small solubility for magnesium which imparts electronic conductivity to the flux. The electronic conductivity decreases current efficiency of the process and also degrades the YSZ membrane. This study investigates different methods for reducing the electronic conductivity of the flux due to magnesium solubility. One effective method shown here is inert gas flushing near the magnesium nucleation site. Potentiodynamic and potentiostatic experiments along with AC impedance spectroscopy are used to characterize the effectiveness of the approach.IntroductionMagnesium is the third most abundant metal in the earth's crust. Since magnesium is the lightest of all metals used for construction alloys, magnesium is the leading candidate to replace steel and aluminum in automobiles. Automobile manufacturers would like to increase magnesium content from 4-5kg per vehicle to 40-IOOkg per vehicle [I]. Using magnesium alloys instead of steel and aluminum can reduce automobile weight and improve fuel efficiency. However, in order for automobile manufactures to make this change, it is generally believed that new cost effective methods of magnesium production must emerge.One approach for magnesium production which has been shown to be effective on a laboratory scale is the direct electrolysis of magnesium oxide utilizing an oxygen-ion-conducting solid oxide membrane (SOM), this is known as the SOM process [2]. A recent study estimated that a commercial SOM plant could produce magnesium from magnesium oxide at a cost that is 40% less than current technologies [3]."

Jan 1, 2012

By C. A. Nogueira, F. Pedrosa, F. Margarido, R. N. G. Guerra

"A hydrometallurgical process for recycling spent Zn-MnO2 batteries was developed, involving leaching with sulfuric acid, purification by precipitation and metals separation for further recovery. Leaching of zinc oxide was easily attained while for manganese oxide was rather difficult depending on temperature and acid concentration. At 90°C and with the liquid/solid ratio of 20 L/kg, more than 95% of zinc is recovered in 30 minutes with 0.5M H2SO4. To attain similar recovery for manganese, higher levels of acid concentration and time are needed (e.g 0.7 M and 2 hours). After leaching a purification step is necessary to remove iron co-dissolved through Fe(III) precipitation. Separation of zinc from manganese by solvent extraction with 1M DEHPA follows in the process route. The countercurrent multistage separation diagram developed allows the production of a zinc electrolyte with 120 g/L Zn and 0.005 g/L Mn, and a raffinate with 16 g/L Mn and 0.013 g/L Zn.IntroductionThe recycling of spent Zn-MnO2 batteries is carried out by dedicated recyclers using several process alternatives [1]. Most of the running processes use pyrometallurgical technologies [2] based on zinc distillation. Alternative treatments by hydrometallurgy have been reported [3-5] but its application is scarce.In order to contribute to the development of alternative solutions, a process for recycling batteries based on Zn-MnO2 systems has been studied. The process is based on the hydrometallurgical treatment of spent batteries in sulfuric acid media (Figure 1). The process starts with the physical processing by shredding using cutting grinders, where the batteries are opened and size reduced, allowing the liberation of the interior electrode particles or pastes. The fines can be then separated and the coarse material containing the steel scrap can be treated to remove the remaining aggregate electrode. The final scrap also contains some plastics and other non-metal materials and can be further valorized."

Jan 1, 2008

By S. J. Ojolo, B. E. Ebiobi, J. A. Kehinde

"Anaerobic digestion is being taken seriously because of increasing concerns about the environmental hazards of wastes. The production of biogas, as an alternative source of energy was investigated in a designed and fabricated 200litre biogas reactor. The digester was operated on a batch-fed basis, and the feed stock was cassava waste which is readily available in Nigerian farms. The main aim was to explore other renewable sources as a means of less dependence on fossil fuels. A total of 1.94dm3/60kg waste of biogas was produced in 40 days of hydraulic retention time (HRT) with the average yield of 0.048dm3/day. The gas burned with a bluish colour indicating presence of methane (CH4). Temperature during the period of experiment varied between 27 and 330C. The pH of the slurry after the experiments averaged 3.21.1. INTRODUCTIONAnaerobic digestion and biogas production are promising means of achieving multiple environmental benefits and producing an energy carrier from renewable resources (Borjesson and Berglund, 2005).Biogas is one of the by-products of anaerobic decomposition of organic matter by microorganisms, mainly bacterial, a process referred to as anaerobic digestion.Biogas is produced by the process of anaerobic digestion of organic material by anaerobes. Biogas can be produced either from biodegradable waste materials or by the use of energy crops fed into anaerobic digester.Biogas, also called digester gas typically refers to methane produced by the fermentation of organic matter including manure, wastewater, sludge, municipal solid waste or any other biodegradable feedstock under anaerobic conditions. The content of biogas varies with the material being decomposed, and the environmental conditions involved. The gas generally composes of methane, carbon dioxide, nitrogen, hydrogen, and hydrogen sulphide (Anunputtikul and Rodtong, 2004). Potentially, all organic waste materials contain adequate quantities of the materials essential for the growth and metabolism of the anaerobic bacterial in biogas production."

Jan 1, 2008

By Wen-Ming Chien, Vamsi Krishna Kamisetty, Amrita Mishra, Ivan Gantan, Prathyusha Mekala, Dhanesh Chandra

"The phase equilibrium and characterization studies by using high temperature X-ray diffraction (XRD) and differential scanning calorimetric (DSC) methods have been performed for binary organic thermal energy storage materials. The organic thermal energy storage materials undergo a solid-solid state phase transition before melting which stores large amounts of thermal energy. Two materials [tris(hydroxymethyl)aminomethane(TRIS) and 2-Amino-2-methyl-l, 3- propanediol(AMPL)] were used for this study. Binary samples of AMPL-TRIS were prepared to perform high temperature XRD characterization and DSC studies and the binary AMPL-TRIS phase diagram was developed. The high temperature solid-state phases of AMPL and TRIS were characterized as a disordered BCC structure. It was found there is virtually no solubility of TRIS in AMPL or vice versa below -75 °C. The maximum solubility of TRIS in AMPL is 11% TRIS at 75 °C. The eutectoid transformation was shown at 19%TRIS-81%AMPL composition and at a temperature of 75°C. Lattice expansion calculations on single phase of TRIS and AMPL have been performed.IntroductionThermal energy storage materials can store a large amount of heat due to the presence of thermal transitions from the orientationally ordered to disordered phases occurring before melting. These molecules (such as amine and alcohol derivatives of neopentane) can reorient as a whole about the central carbon atom to form orientationally disordered crystals (ODIC) and their spherical shape makes them reorient relatively easier. Thermal energy storage materials are becoming increasingly important as a renewable energy resource. These molecules undergo large changes in enthalpies at solid-solid transitions. The presence of these compounds with large enthalpy changes are identified as potential thermal energy materials and some of die applications are solar cell systems [1-3]. Binary mixtures have been found as a way to adjust the transition properties in addition to pure compounds [4]. Tris(hydroxyrnethyl)aminomethane (TRIS, C(CH2OH)3NH2) and AMPL, CH3C(CH2OH)2NH2) are two important thermal energy storage materials."

Jan 1, 2012

By Shadia J. Ikhmayies

"Nanocrystalline fluorine-doped tin oxide, SnO2:F, thin films were prepared by the spray pyrolysis (SP) technique on glass substrates. The films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray dispersive spectroscopy EDAX and transmittance measurements. X-ray diffraction patterns revealed the nanocrystalline nature of the films where the grain size was estimated based on the Sherrer formula. SEM micrographs showed that the films are uniform and totally covered with the material and they confirmed the nanocrystalline nature of the films. The absorbance was deduced from the transmittance measurements, and its first derivative was used to estimate the optical bandgap energy. Bandgaps larger than the bandgap of the bulk SnO2iF were obtained, indicating the presence of quantum dots. The hyperbolic band model was used to estimate the radii of the nanocrystallites. A comparison between the results of the different methods was performed.IntroductionTin oxide, SnO2, thin films are n-type semiconducting, transparent materials, which have numerous important applications in optical-electronic device technology. The optical transparency of SnO2, together with its chemical and mechanical stability, makes SnO2 films suitable for many other applications, such as transparent conductive coatings, gas sensors and heteroj unction solar cells [1]. In particular, SnO2 thin films have drawn much interest because of their potential application and integration with microsensor devices. Considerable attention has recently been focused on the development of solid state gas sensors based on thin films with a crystallite size smaller than the Debye length of the material, which show increased gas sensitivity and short response times [2]. In many of these applications, a doped SnO2 film is used as an active layer. Among the various dopants, fluorine is often preferred, because fluorine doping results in films with high transparency and good conductivity [1]."

Jan 1, 2012

By Fathi Habashi

"Davy, Faraday, and Bunsen laid the foundation of electrometallurgy which had a· great impact on other areas of metallurgy. Electrometallurgy is presently dominated by the production of aluminum, the electrorefining of copper, and the electrowinning of zinc. It has also been successful in the electrowinning of copper from solutions obtained by leaching-solvent extraction. Electrowinning processes, however, are capital intensive. Improvement of the present technology should be intensely investigated especially when it is expected that such processes will increase greatly as a result of a shift from certain pyrometallurgical processes to pressure hydro metallurgy.INTRODUCTIONPyrometallurgy was used for thousands of years to produce copper and iron from their oxide ores!). Today it is still the only route to produce iron and steel and it is certain that it will remain so for many decades to come because pyrometallurgy is most suitable for the treatment of high grade oxide ores. Even when high grade iron ores are exhausted, it is possible to beneficiate the low-grade ores and produce pellets suitable for reduction in the blast furnace, which is a very efficient reactor, being a heat exchanger as well. Hydrometallurgy on the other hand can be traced to the time of alchemists in the Middle Ages when they were seeking to transmute base metals into gold, and thus were able to prepare many acids and bases which are the essential leaching agents."

Jan 1, 1997