Search Documents

By E. D. Fox

Introduction The financial statement of the hypothetical Gold Mining Company, which forms the background of this survey, was designed for the Institute with the express abject of having it assessed in respect to Profits by the several taxing bodies representing the Federal and Provincial Governments, which comprise the Dominion of Canada. On the completion of the figures, copies were sent to the several Ministers of Mines, accompanied by a request that they be submitted to their taxing authorities and assessed accordingly. The response, while it was not general, was very favourable, and at all times we were treated with the utmost courtesy and patience, and what has been set forth in the compilation bears the authentication of the various government officials who are immediately concerned with taxation. The data itself constitutes a fairly comprehensive digest of taxation as it directly applies to gold mining profits in Canada. The Hypothetical Balance-Sheet (See Exhibit A) In the balance-sheet schedules 1 and 2 (Exhibit A), income is divided between taxable and non-taxable classifications, and here it should be noted that the division contemplates only the assessment for Dominion income tax. The same applies to the factors of exchange and depletion. Therefore, in making comparisons, it is to be borne in mind that the set-up for assessment to the Provinces, that is, Manitoba and Alberta, will stand as if the gross non-operating income is taxable, with the reservations as shown in the notes below the schedules.

Jan 1, 1934

By Robert D. Brown

The federal government kicked off the new budget season in November 1978, when Finance Minister Chretien announced a handful of proposed amendments to provisions of the federal Income Tax Act and Regulations affecting mining. (See Tax Notes in the January 1979 issue of the CIM Bulletin.) Declaring in his budget speech that these changes were in response to the report of the joint federal/provincial task force on resource taxation, Mr. Chretien tossed the ball to the provinces-" I want to take the lead here... I feel confident that the provinces will do their part". Quebec and Ontario, picking up the ball in their spring budgets, have announced favourable modifications to the provincial taxes on mining, with these moves being paralleled in the recent Manitoba budget, which proposes a flatrate mining tax to replace the previous controversial two-tier royalty. In the meantime, the federal government passed a host of amendments to the federal earned depletion regulations. The result is yet another batch of complex tax changes for the industry to note and digest, but this time with the hopeful factor that most of the changes are favourable to the industry. This article reviews the current status of the federal budget changes, comments on the Ontario, Quebec and Manitoba proposals, and reports on the changes to the earned depletion regulations that were passed by Order-in Council in March 1979.

Jan 1, 1979

By C Caris, K Fowle, M Schmid, E van Wyk, D Schofield, A Squelch, M S. Kizil

This paper has been written collaboratively by members of the International Mining VR Group. It is the first of a series of papers. Mining in the 21st century is a high technology industry that strives to reduce risk and improve safety through the use of improved processes and procedures. This risk reduction process is aligned with the innovative use of technologies often developed for other industries. Computer-based visualisation systems and their content are such innovative technologies, in particular the use of virtual environment systems and mixed reality. A primary objective of developing virtual environment systems and the mixed reality content displayed in them for the mining industry is to allow mine workers and operators to practice mine processes and demonstrate competency in tasks that will be encountered in day-to-day mining operations at mine sites. It is anticipated that providing easy access to virtual environment systems will facilitate the avoidance of high-risk situations through improved knowledge, skills, understanding and decision making. Via virtual environment systems mine workers will also be able to practice infrequent or emergency events and maintain preparedness for such events. Day-to-day mining practices can also be evaluated. The rapid pace of technology innovation and the decreasing cost of simulation hardware and software present a plethora of technology to the uninitiated. This can be confusing. In this paper taxonomy is presented that classifies hardware, what it can display and also content that can be included or displayed on the various computer-based visualisation systems. The taxonomy provides insight into where technology can and may be implemented in the future as virtual environments are a dynamic and evolving technology. The taxonomy should also assist in the decision making process when scoping or selecting technology for a particular purpose.

Jan 1, 2008

By Sergio Estebanez, Martha Gross, Ruben Rubal, Yvonnick Rescamps, Alexandre Cochennec

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in coastal Virginia, USA will add two 1.5-mile (2.4 km) TBM bored tunnels alongside two existing immersed-tube tunnels between artificial islands. The site’s unusual constraints and the requirements of a large-diameter variable-density TBM shaped the design-builder’s decisions for handling TBM inputs and outputs, siting the TBM plant and supporting equipment, and sequencing tunnel-construction operations. This paper addresses the logistics necessary to enable key functions of the 46-ft (14-m) TBM and its ancillary equipment, including transport of most materials by barge, U-turn of the TBM on an artificial island, and delivery of materials for the second tunnel through the first one while interior structures are under construction.

Jun 13, 2021

By Francesco Chiappalone, Marco Invernizzi, Franco Gasperin, Fabrizio Fara

As part of the Ship Canal Water Quality Project, 2.7-mile Combined Sewer Overflow tunnel is excavated with a 21.5-foot diameter EPB Tunnel Boring Machine. Due to the difficult geological and hydrogeological conditions, the tunnel is excavated maintaining a ground support pressure between 1 and 3 bar imposing significant challenges to the projects. The first part of the paper describes the general characteristics of the project while the second part focuses on the challenges and technical details of the pressurized breakthrough that took place in a deep shaft excavated in urban environment as part of the project.

Jun 23, 2024

By Gary Peach, Peter Mason

Planning and estimating progress rates and costs for tunnelling is always best done based on experience and historic precedent. Much precedent is available but the use of data monitoring, data mining and other retrieval techniques on modern TBM machines can enable this to be further expanded and refined. Advance rates can be related much more closely to rock types as can associated rock bolt and mesh/ shotcrete requirements. This in turn can lead to a further refinement in best likely combinations of equipment, such as shotcrete jumbos, better selected for the anticipated conditions, rather than the potential advance rates of the machine. Efficient and timely construction of the tunnel will also be linked to times needed for finishing work, such as contact and void grouting and to how this can be initiated while the TBM is still in operation, in order to save overall construction time. Indeed, this in turn may affect the most preferable layout and construction details of the permanent tunnel. Considerable experience has been gained in the use of two large diameter TBM tunnel drives through the Himalayas at the Neelum-Jhelum hydropower project in Pakistan. All the above aspects will be discussed in the paper based on the considerable experience and data which came from that operation, including appropriate measures in highly stressed areas potentially subject to rock burst.

Jun 13, 2021

By Francesco Chiappalone, Franco Gasperin, Fabrizio Fara

This document describes the challenging task of mining through tiebacks using a 21'-8" diameter Tunnel Boring Machine (TBM) as part of the Ship Canal Water Quality Project. The mining operation involves navigating through 17 tie-backs that are evenly spaced at 8-foot intervals, with many intersecting the full face of the cutterhead. Detailed analysis and review of TBM parameters specific to this area have been conducted to ensure operational efficiency and safety. Hyperbaric interventions have been planned and coordinated, encompassing pre-mining preparations, continuous monitoring and adjustments during the mining process, as well as post-mining measures. The document highlights the complexity and importance of strategic planning and execution to successfully overcome the tie-back intersections during the mining operation.

Jun 23, 2024

By Bo Kyung Sim, Dae Young Kim, Jae Won Lee, Ebrahim Farrokh

"The contract C931 of the downtown line 3 (DTL3) mass rapid transit system of Singapore includes half a kilometer twin tunnels running between Mattar and Macpherson stations. An EPB TBM of 6.6 m diameter was used to excavate both of these tunnels. The tunnels pass predominantly through a very stiff silty/clayey fine to coarse sand from the Old Alluvium Formation. In this paper, TBM selection procedure, TBM performance evaluation, and some of the tunneling operation challenges with the TBM in the Old Alluvium Formation are discussed. In this regard, soil conditioning trial tests were performed to resolve the clogging issue and low TBM performance. Thorough TBM operational data analysis was performed to detect high soil abrasivity, backfill grout leakage, and foam nozzle clogging. The results of some of the applied modifications are also discussed to show their effects on the TBM performance improvement. Finally, some of the challenging TBM design specifications are also discussed. INTRODUCTION Tunneling and underground construction in Singapore has been increased in the last 30 years due to the demand for public transportation systems and the limited space above the ground for the infrastructure development. Downtown Line Stage 3 (DTL3) Mass Rapid Transit (MRT) system has 21 km total route length and consists of 16 stations. DTL3 Contract C931 runs between Mattar station and MacPherson station. The construction works in this contract include twin bored tunnels of 6.6 m diameter and 450 m length and a TBM launch shaft of nearly 30 m depth. The tunnels run in urban area below Kallang Paya Lebar Expressway tunnel (KPE), Kallang River Canal, and Circuit Link. Figure 1 shows the alignment of the tunnels in between two subway stations. The tunnels were excavated by an earth pressure balance (EPB) tunnel boring machine (TBM) through the Old Alluvium (OA) formation, a challenging geological formation in the sense of its abrasivity and stiffness. The Old Alluvium Formation mostly includes stiff to very stiff clayey and silty sand. The soil is un-weathered cemented to semi-cemented dense, mainly with a low permeability coefficient of 10-7 m/s and high SPT values (almost 100). The soil is classified as “very high abrasive” according to NTNU SAT test classification (SAT value of 15 to 42). The construction of the first tunnel drive was slowed down due to a number of factors related to soil conditioning and TBM operation. In this regard, a thorough analysis of the TBM operational parameters from the excavated sections was performed to identify the problems in time to prevent unwanted construction delays in the subsequent sections. In the following sections, a brief overview of the criteria used for TBM selection is presented at first. Then, the results from the analyses and tests performed to assess soil conditioning, grout leakage, and soil abrasion are presented. The last section discusses some of the tunneling design features that challenged the TBM operation in this project."

Jan 1, 2016

By Lance Rasband, Richard Hanke, John Starcevich

"The 17.4 meter (57 ft) diameter tunnel boring machine (TBM), the world’s largest at the time of her launch in 2012, locally referred to as “Bertha,” is stuck. Incapacitated due to mechanical failure approximately 36 meters (120 ft) beneath downtown Seattle, situated precariously between the deteriorating Alaskan Way Viaduct and the failing Seattle Seawall. Accessing Bertha with a vertical shaft provides the best approach to address all facets needed for repairs and will allow the full removal of Bertha’s cutter head and related inner workings. Limited area above the tunnel alignment and the physical restrictions of existing infrastructure, create significant challenges for the design of an otherwise symmetrical shaft, requiring special attention to design and layout. Consequently, the access/recovery shaft design required a combination of 3m, 2.5m, 2.2m, 1.5m and 1m diameter unreinforced drilled secant piles coupled with various ground improvement techniques and dewatering, to fully satisfy the shoring design requirements. This paper will describe the shaft installation procedures, equipment used and pitfalls encountered while undertaking access shaft construction of this magnitude.INTRODUCTIONTunneling on Seattle’s SR99 tunnel project began in July of 2013. After slowly mining through a 4.5 m (14.76 ft) thick fiber-reinforced concrete headwall and the first of three stabilized “safe havens,” Bertha would proceed along the proposed alignment through 122 meters (400 ft) of jet grout improved soil at a rate of slightly over 1.6 m (5.25 ft) per day. Once past the improved area, it was planned that “Bertha” – would be moving at a rate of about 11 m (36 ft) per day. By the end of October 2013, Bertha had mined roughly 131 m, (430 ft) averaging 1.4 m (4.6 ft) per day and had begun mining within native soils. By December 2013, tunneling had reached the 244 m mark and Bertha was averaging 3.6 m (11.8 ft) per day, achieving as much as 12.8 m (42 ft) of progress on given days. Unfortunately, on December 6th, 2013, Bertha began to stumble and all progress quickly came to a halt.It was initially reported that an obstruction had stopped Bertha in her tracks. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic pressure around the TBM, and allow visual inspection of the cutter head from within the TBM, and also to investigate for the presence of obstructions at the face of the cutter head. During this inspection, fragments of steel pipe were discovered entangled in the cutter head. The fragments were apparently from an abandoned 254 mm (10 in.) diameter monitoring well casing, previously installed by WSDOT to monitor ground water conditions for the design and planning of this tunnel project. After the steel was removed from the cutter head and cleared from Bertha’s path, tunneling resumed. It was then discovered that Bertha was only able to generate a slow crawl."

Jan 1, 2016

By Devan Naik, Matthew Stokes, Andy Nigro

This paper describes the surgical removal of a 24 ft dia. Slurry Shield TBM entombed beneath one of the country’s busiest commuter rail interlockings, the Harold Interlocking in Queens, NY, and the construction of the interface to a cut/cover tunnel which extended the mined tunnel section. A sophisticated SOE was built around the TBM to support active track loads within 8ft. of the excavation. Once the TBM head and guts were removed, a full round CIP lining was installed connecting the existing precast tunnel liner to the C/C tunnel under construction. All this construction was done on a narrow island of land without road access nestled between 7 mainline LIRR/Amtrak rail lines.

Jun 13, 2021

By Dan Swidrak, Bill Zietlow

Halfway through a 17,770-ft long stormwater tunnel, an 11-ft diameter TBM encountered a karst void below the Mississippi River in Missouri, resulting in significant inflow. It was decided that the TBM could not safely advance without external intervention. Low-mobility grout was pumped from the surface. A rescue shaft was constructed and a conventional tunnel with spiling support was mined back to the machine. The TBM was removed and a 14-ft diameter TBM equipped with probing drills was relaunched. Probing from the new TBM encountered one additional karst feature but the machine advanced after grouting and successfully completed the tunnel.

Jun 23, 2024

By Hee-Young Chung, In-Mo Lee, Jeongjun Park, Hangseok Choi, Seok-Won Lee

"When using a Tunnel Boring Machine (TBM) during tunneling work, unexpected ground conditions can be encountered that are not predicted in the design stage. These reduce the stability of tunnels, and can result in considerable economic losses. This paper analyzes the potential risk events that may occur due to risky ground conditions. A resistivity survey is utilized to predict the risky ground conditions ahead of the tunnel face during construction. The potential risk events are evaluated considering both the occurrence probability and the impact. A TBM risk management system that can suggest proper solution methods for potential risk events is also developed. Multi-Criterion Decision Making (MCDM) is utilized to determine the optimal solution method to handle risk events. Lastly, an actual construction site, at which a risk event occurred during tunnel construction, is analyzed utilizing the Earth Pressure Balance (EPB) Shield TBM, to verify the efficacy of the proposed system.INTRODUCTION The Tunnel Boring Machine (TBM) method has been widely adopted in numerous tunneling projects because, as a mechanized tunneling method, it is also environmentally friendly, exhibiting minimal noise and vibration when compared with conventional tunneling method. In addition, it provides considerable economic benefits that allow for a high advance rate for long drives during construction. However, the TBM method has a limitation, as it is unable to deal with unexpected situations during construction, as the system is not capable of moving backwards. This leads to delays or even stoppages, and a corresponding increase in construction costs due to the need to arrange for alternative equipment and solutions. It is essential to retain systematic management in order to prevent or deal with unforeseen consequences such as the collapse of a tunnel face, ground surface upheaval or settlement, and construction delay due to water leakage during construction. Therefore, a systematic risk management system that is applicable during the construction stage of the TBM tunnel should be developed, taking into account the predicted risky ground conditions ahead of the tunnel face in advance."

Jan 1, 2016

By Joseph A. Dos Santos

The largest TBM (Tunnel Boring Machine) tunnels are typically along modest slopes, but not always. Occasionally high slope angles are required beyond the capabilities of conventional open trough trailing conveyors. A 2019 project required a large TBM to ascend to an incline angle of 25°. A Sandwich Belt high angle conveyor could easily solve the high angle conveying problem but such a system must include all of the features of the conventional trailing conveyor, particularly the ability to extend with the TBM advance. The writer responded to the challenge and developed a TBM trailing Sandwich Belt high angle conveyor with all of the needed features. The invention (U.S.A. patents awarded October, 2021 and November, 2022) however goes beyond the 2019 project requirements and extends to any high angle incline. This writing first presents the broad Sandwich Belt high angle conveyor development, then its use in various construction and tunneling projects prior to this TBM Sandwich Belt trailing conveyor invention. Finally we present the new TBM Trailing Sandwich Belt high angle conveyor with all of its features and implications.

Jun 13, 2023

By H Vigil, G. Peach

Long tunnels with only one access shaft pose many program problems for logistics, combine these with the requirement to drive directly out under the seabed for 10.2 km, and the program issues become even more challenging. The Musaimeer outfall tunnel was one such tunnel and to meet and eventually improve on the planned completion date required a complex and extensive management of all tunnel logistics required to support consistent tunneling for a two-year period. This technical paper will discuss the management issues and solutions implemented to meet the challenges of the Outfall tunnel construction.

Dec 1, 2022

By H. Vigil Fernandez, G. Peach

The Musaimeer pump station and outfall project located in Doha Qatar, was designed to collect and manage ground and stormwater and then discharge the treated waters offshore. The project constructed a long outfall tunnel using an EPB TBM with segmental lining, each tunnel ring being 1.35 m in length with an internal diameter of 3.7 m.. The diffuser structure was a 6-arm structure, measuring 294m by 40 m connected to a central manifold in turn connected to the TBM constructed tunnel via a riser shaft drilled from an off-shore barge. This technical paper will discuss the planning, methodology and construction practices employed to connect the TBM tunnel to the diffuser structure 10.2 km offshore.

Jun 13, 2023

By Jeff Reid, Mohamed Maghari, Nicholas Joens

The Burnaby Mountain Tunnel was an integral part of the Trans Mountain Expansion Project. General Contractor, Kiewit Ledcor TMEP Partnership (KLTP), contracted with McNally Construction to build an underground tunnel between the Burnaby and Westridge Marine terminals under Burnaby Mountain. The pipeline was constructed within a 2.6-kilometre tunnel, eliminating the need to run the pipeline over the mountain and minimizing community impacts. The complexities of this Project led to multiple innovations, including the design of a Tunnel Boring Machine (TBM) capable of excavating through mixed-faced conditions concurrently thus allowing the Project team to complete the tunnel with limited geotechnical information.

Jun 23, 2024

By John W. Leonard

The typical tunnel boring machine in use on today's tunnel project uses 15'2-inch diameter cutters at a nominal load of 45 kips per cutter. The cutterhead rotates at a speed of 120 over D revolutions per minute where D is the cutterhead diameter in feet. The typical machine operates about 50 percent of the time. Delivery of a new machine takes 12 to 15 months. The TBM is a specialized tool and not applicable to all jobs. There is a range of job conditions that limit the economic use of a TBM. The machine should provide a thrust per cutter at least twice the compressive strength of rock in psi and up to three times the rock strength is required if in "granitic rocks." The rock strength in psi must be at least three times the cover above the tunnel in feet or the machine may stick. For example, 2,500 feet of cover requires at least 7,500 psi rock to avoid problems. When the RQD's over a significant distance of the project are less than 50, the TBM becomes support-bound. When a large percentage of the time is spent waiting while the ground is supported, the TBM cannot perform well (See Figure 1). This problem increased inversely with tunnel diameter. We are finding that increasing the RPM's does not significantly increase progress. The increased RPM results in a substantial decrease in cutter penetration. The explanation for this decrease appears to be vibration, cutterhead drag, or lack of stiffness in the cutterhead (See Figure 2).

Jan 1, 1981

By P B. Card

"The website www.economicevaluation.com.au, which had its origins at the Project Evaluation Conference 2009, provides a free way for industry professionals to teach themselves economic evaluation. At its core is a set of fast-moving modules and three worked examples.The website recognises that economic evaluation is a discipline with a hierarchy of three levels:decision-makingevaluating the project/businesshands-on modelling.There are a set of modules for each level that describe the concepts and activities in detail. These emphasise that the most important and rewarding work is the evaluation of Level 2. The economic model created in Level 3 is merely a working tool and should not become a sophisticated ‘trophy’ in Excel that only one or two people can comfortably use.Hands-on modelling contains three sets of practices designed to make any model rigorous and intuitive so that it can be easily understood and used by others in the project team. Even if the model develops into a long, detailed and complex workbook, it should remain easy to follow and be intuitive. The website advocates freedom to devise any architecture that best suits the project under study, but promotes rigour through the following practices:four cash streams and graphsthree architectures – concept, prefeasibility and feasibilitysix principles.The modules in the Level 2 evaluation use conversational language to describe in detail the broad range of activities needed to properly understand and characterise a project/business. It stresses that net present value is nothing more than the mathematical treatment of a whole set of opinions, is not an absolute truth and is only a fraction of the evaluation process. The modules describe in detail the range of economic metrics that should be computed and the full spectrum of equally important characterisations required to make the decision in Level 3.CITATION:Card, P B, 2016. Teach yourself economic evaluation, in Proceedings Project Evaluation 2016, pp 160–171 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By Jochen Petersen

This paper gives an overview of the various strands of postgraduate and undergraduate training offered in the Department of Chemical Engineering at UCT. Since 2003 the Department is offering a formal postgraduate MSc programme in hydrometallurgical engineering aimed especially at graduate work-based engineers, with 5 weeks of intensive course work plus a research dissertation on a work-related project. This programme has now run 5 times over the years and produced some 20 degrees. The paper reflects on the experiences with running the course, especially the difficulties experienced with supervising industry-based external students. Furthermore, through the Department a graduate training program is offered for all junior metallurgists at a major South African minerals company. This 2-year program, which is currently on its 12th cohort, offers 1 or 2 week intensive blocks of course work alternating with longer stints where the candidates are based at various operations. Although primarily focussed on minerals processing, it has a significant element of hydrometallurgy in it and in recent years an advanced hydrometallurgy stream has been introduced. The paper reflects on the development of the program over the years, the benefits it has provided to the company as well as some of the challenges that remain. Finally the paper gives an overview of hydrometallurgy related undergraduate and research-only postgraduate MSc and PhD projects at the university. Some emphasis is placed on the recently launched South African Minerals and Metals Research Initiative (SAMMRI), a joint government-industry programme to support university-based research in the area of applied metallurgy.

Jan 1, 2014

By Elaine T. Cullen

Miners, like many skilled blue-collar workers, are not traditional learners. They have not always been successful in classroom-type settings, preferring to learn on the job in a hands-on environment. U.S. law requires that miners have a minimum of 8 hours of safety training annually, plus 40 hours for underground miners and 24 hours for surface miners when they enter the industry. However, miners rarely view this training time positively. In fact, it has been called “safety jail” by many, who regard it as a time to get a little extra sleep While mining has become far safer in the past 100 years, it is still a dangerous occupation. The Office for Mine Safety and Health Research, a part of the National Institute for Occupational Safety and Health (NIOSH), has funded a project for the past 4 years to address this challenge. The purpose of the research was to find a way to develop effective safety training for these people. Miners are born story tellers. They share “near miss” stories, stories about master miners they have known, and stories about how things used to be. These stories not only pass along information about what will happen if a miner fails to respect the mining environment, they also instruct listeners in the culture of mining and the values that it embraces. Stories, it seems, are a way to get safety messages across to miners, especially inexperienced ones, and using older, wiser miners in these stories is an obvious choice. This paper will discuss how a series of training videos was developed, how “master miners” and story lines were chosen, and how the resulting videos have been received in the mining industry.