Search Documents

By D. Lelinski

Air-sparged hydrocyclone (ASH) flotation is one of the new promising technologies. Numerous applications have been successfully tested since its conception; nevertheless, research and development efforts have continued to provide for further improvements with respect to operating conditions and design considerations. Results from experimental studies on bubbles generation in the ASH system are presented in this paper. Bubble size distributions generated during ASH operation have been determined using a high-speed photographic technique. The influence of many factors including surfactant concentration, water flowrate, and porous tube pore size has been studied. Test results indicate that these process variables have a profound effect on the bubble size distribution. With an increase in surfactant concentration or water flowrate (shear field) the bubble size distributions become narrower and shift toward smaller average bubble diameters. However, the influence of pore size is more complicated. Depending on the experimental conditions the average bubble size was found to range from about 100 to 300 microns in diameter.

Jan 1, 1995

By William Watson

Coal production in the United States in 2010 increased to a level of 960 Mt (1,085.3 million st), according to preliminary data from the U.S. Energy Information Administration (EIA), an increase of 1 percent, or 9.43 Mt (10.4 million st) above the 2009 level of 975 Mt (1,074.9 million st) (Table 1). In 2010, U.S. coal consumption increased in all sectors except commercial and institutional, while total coal stocks fell slightly for the year. Coal consumption in the electric power sector in 2010 was higher by 4.5 percent, while coking coal consumption increased by 37.9 percent and the other industrial sector increased by 7.1 percent. The commercial and institutional sector, which prior to 2008 had been called the ?residential and commercial? sector and is the smallest of all the coal-consuming sectors, declined by 3.1 percent in 2010. (Note: All percentage change calculations are done at the short tons level.) U.S. coal exports increased from the 2009 levels due mostly to higher demand for metallurgical coal, while coal imports decreased for a third year in a row. The increase in coal consumption for electric generation during the year was the consequence of improving domestic economic conditions further bolstered by a cold winter and warm summer in important coal-consuming regions. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers, including useful thermal output) in the U.S. increased in 2010 by 4.2 percent. Coal-based generation also increased, resulting in a 38-Mt (42-million st) increase in coal consumed in the electric power sector. Coal use in all the sectors other than the electric power sector increased by 13.9 percent to a level of 65.9 Mt (72.7 million st).

Jan 1, 2011

By Searl. Milton F.

Introduction The urgency of further development of our domestic energy resources becomes more apparent every day. The production capability of existing facilities, taken in the aggregate, declines perhaps 10% per year; imported energy is expensive if available at all; conservation helps reduce demand but eventually will reach a point of diminishing return; new energy sources are promising but past experience, as with nuclear power, teaches us lead times are long and success is not assured. To approach the energy future rationally, it is essential to have some idea of the size of the nation's remaining energy resources, their characteristics, and the degree of uncertainty involved in their estimates. Resources are, of course, only one end of a long chain leading to energy supply to the ultimate consumer. They are an essential element, however, and the only one not under society's control. Given that the resources and a national will to produce the energy exist, it is possible to convert the resources to supply in, generally, an environmentally reasonable manner. However, the process of developing supply takes time. Government must permit access to the resource, and remunerative prices and further evolution of technology are required. This paper does not deal with these essentials, but they must not be forgotten. This discussion is limited to coal, oil, natural gas and gas liquids, uranium, and oil shale. Other energy sources are discussed elsewhere in this issue. Crude Oil Conventional crude oil resources are of greatest concern today, given our dependence on imported oil and its rapidly rising price. Estimates of oil originally in place (OOIP) range from 619 billion bbl to 1,094 billion bbl, differing by almost a factor of two (Table 1). This is surprising because the U.S. is a mature petroleum province with over 120 billion bbl produced and over 400 billion bbl OOIP discovered. Differences in the estimates involve differences in the experience of the various estimators, the interpretation of present geologic information and historical statistics, the methodology, and probably the extent (i.e., water depths) for which offshore resources are included. The range shown for the estimate of a given estimator appears to be primarily due to geologic uncertainty. This uncertainty can be measured by taking the ratio of the low and of the high estimate to the expected estimate for that information source. The low estimates range from 0.85 to 0.87 of their respective values. The high estimates range from 1.18 to 1.27 of the expected values. In all cases the high estimate is further from the expected value than the low,

Jan 9, 1980

By Bahram Sameit

Blast engineers have been taking advantage of image-based rock fragmentation analysis methods for the past three decades to estimate rock size distributions. These methods utilize a range of image segmentation techniques, from manual to fully-automated, to delineate the edges of rocks in images. Rock delineation results are then converted to physical rock sizes (and percentage passing curves) by scaling the image pixels to correspond to physical measurements. The size scaling process is critical for acquiring physical measurements, but specifc to the limitations of different applications. This article starts by presenting a shovel bucket-based fragmentation analysis system, where scaling is done using the known width of the shovel bucket within the image. It will then describe methods that use pictures captured by digital cameras with scaling reference objects in the view. Finally, the article presents a method that uses three-dimensional imaging to capture images without the need for scaling reference objects.

By A. H. Shapiro

A decanter centrifuge of novel design was developed for the dewatering of fine-solids slurries having micron-range particles that form paste-like, flowable, hard-to-dewater cakes. The design combines a compound beach with a cake-flow control structure that allows expressed liquid from the cake in the dry beach region to be returned back to the liquid pool while maintaining high solids throughput. In order to provide optimal performance with various operating parameters (feed rate, centrifugal gravity, pool, differential speed, concentration of feed solids, and different slurry types), the cake-flow control is adjustable. The second part of the beach is preferably at zero angle. Tests showed that the new design allows increases in both solids dryness and solids throughput.

Jan 1, 2001

By Suresh P. Babu, Joseph W. Leonard, Richard Muter, D. P. Sen

OUTLOOK FOR COAL UTILIZATION In 1975, about 650 million tons of bituminous coal and lignite mined in the United States was used to meet 55% of the primary energy input for electric power generation and 26% of the total industrial consumption.1 Even though this amounts to only 21% of the total energy requirements, it is believed that with the declining natural gas resources and uncertainty of liquid fuel imports, coal will assume a more dominant role in suppplying our future energy needs. A regional breakdown of the coal reserves of the United States along with their characteristics is shown in Table I. At present the United Stares Energy Research and Development Administration (ERDA) and the US Bureau of Mines (USBM) are financing extensive research programs in advanced mining methods and energy conversion processes. The increased demand for wal which may result from these research programs may also create large-scale environmental protection problems. As more and more coal is mined the production of undesirable coal fines and dust also increases proportionally. The USBM and the Environmental Protection Agency (EPA) research in this field includes development in the areas of instrumentation for qualitative and quantitative analysis of wal dust, protective devices, and dust collectors. Dust control by water sprays, steam, and foam are also being investigated. Other aspects of safety in mining include developing methane drainage techniques prior to coal mining, fire and explosion prevention, and neutralization and disposal of acid mine waters. It is the belief of coal technologists that when the emphasis shifts to coal as the primary source of energy. the existing methods of mining and preparation of coal must be improved considerably to supply large quantities of quality coal for energy conversion. It is the objective of the present large-scale research financed by ERDA to produce substitute fuels from coal. Large-scale gasification pilot plants are being constructed by Bituminous Coal Research, Consolidation Coal Co., Institute of Gas Technology, and the Pittsburgh Energy Research Center to produce coal gas of natural gas standards at 1,000 psig. The processes being adopted by these pilot plants are oriented towards recovering most of the sulfur from coal by absorbing H2S and its subsequent conversion to elemental sulfur. The environmental protection standards will be strictly followed in using the results of these pilot plants to construct large-scale coal gasification plants in the latter part of the 1970's. With the increasing awareness of the need for air pollution control, considerable research is being done to minimize sulfur dioxide emission from thermal power plants. Utilization of limestone and dolomite scrubbing systems and caustic treatment of stack gases have proved to reduce sulfur and nitric oxide emissions by about 90 to 96%.3 Currently, about 22 scrubbers are in use in the United States to reduce sulfur in stack gas emission. In the long-term, it appears that optimal combinations will be developed involving both advanced coal preparation technology and wet scrubbing. The sulfur compounds are converted either to elemental sulfur of sulfuric acid. Besides the sulfur compounds, the major byproduct of the coal utilization industry is the large amount of coal ash. The Coal Research Bureau at West Virginia University has developed a practical use for coal ash as a structural material. The coal industry will undergo revolutionary changes when coal becomes the primary source of energy. New coal mining and preparation processes will be introduced to meet the ever-increasing per capita energy requirements. 2. BENEFICATION Introduction Coal preparation, like the beneficiation of ores, is also aimed at the separation of values from associated waste. Even though the unit operations involved when enriching ores and coal are similar, there are certain characteristics unique to coal preparation. Unlike the scattered and concentrated veins of underground minera1 ores, coal is distributed uniformly and very much in abundance in the coal mines. Coal occurs as the metamorphosed sedimentary deposits of vegetable matter, while metal and mineral deposits occur in great varieties of forms, structures, and origin-from igneous to sedimentary and metamorphic. The mined coal, being much more friable than mineral ores, is subjected to less intensive size reduction operations. Ores are usually ground to a very fine size for subsequent concentration, while coal is crushed to a coarser size, since considerably less liberation is needed to achieve the desired degree of separation. Since mineral matter is to a great extent discretely distributed in coal, concentration is mainly achieved by taking advantage of differences in specific gravity between clean coal and associated waste. In general, about 90% of coal is concentrated using specific gravity separation and about 10% by froth flotation. In contrast, these operations are frequently reversed in the beneficiation of ores. In coal preparation almost all fractions separated during various stages are made use of. while large amounts of gangue material are rejected in the concentration of ores. Hence, coal generally has a much lower ratio of concentration than ores. Since ore deposits are frequently more variable and mineralogically complex than coal, beneficiation of ore may require more plant flexibility and point-to-point quality control. This characteristic difference between the mineral ores and coal is attributed to the generally used one-step processing in coal as compared to the multiple-step processing of ores. Dewatering to enhance the energy content of coal is usually considered a major unit operation. Even though thickening and filtration are common for dewatering ore concentrates and cleaned coal, vibrating centrifuges and disk filters find unique application in the coal industry for achieving these types of solid-fluid separation. In coal preparation, thermal drying is carried out in separate units at the mine. While ore concentrates are usually dried at the smelter. Although the drying of ores is seldom considered dangerous, volatile matter and combustible dust are reasons why the thermal drying of coal can be hazardous. Open air storage of ores and mined coal results in partial oxidation. Unlike the oxidation of ores, the oxidation of the pyritic and carbonaceous constituents of coal together with the heat of condensation of moisture contribute to spontaneous heating and the subsequent combustion of coal in storage. Among the other significant difference between concentration of ores and coal are the weight and capacity of processing equipment. Coal processing employs less cumbersome, higher capacity units while the beneficiation of ores usually requires much more massive and frequently lower capacity equipment. Properties of Coal Which Influence Design The widely varying and heterogeneous composition of coal, due to metamorphism, determines the preparation design and uses of the resulting products. Petrography serves as a useful system of classification to identify the coal types present and their distribution. Early

Jan 1, 1985

By S. C. Schmelter

The destabilizing effect of water pressure on rock mass stability is examined quantitatively by the finite element method. A coupled code that accounts for the simultaneous effects of rock mass deformation and transient fluid flow is used for this purpose. The traditional soil mechanics assumption of an incompressible fluid is shown to be untenable for the analysis of porous, fractured rock slopes. A Mandel-Cryer effect, a transitory but elevated and potentially destabilizing water pressure following a cut, was not observed.

Jan 1, 1997

By I. Iwasaki

The presence of calcium ion in iron ore pulps causes heterocoagulation of montmrillonite on hematite leading to indiscriminate dispersion. Two methods were investigated to control the adverse effect of montmorillonite: chemical method using such complexing agents as EDTA and sodium tripolyphosphate, and mechanical method involving ultrasonic treatment. Their roles in controlling the adverse effect were investigated by zeta potential measurements, starch adsorption tests, and flocculation and selective flocculation tests.

Jan 1, 1986

By R. L. Grayson

For the years 1990 and 1991, West Virginia's underground coal small-mine fatality rate « 20 employees) was approximately ten times higher than the national coal industry rate. Although the total number of fatalities decreased to 17 in 1992 (from 22 in 1991), West Virginia still led ,the nation in coal mining fatals. A team of mining and safety professionals from West Virginia University studied the problem over the past year, interfacing with the Mine Safety and Health Administration and the West Virginia Office of Miners' Health, Safety and Training. A clear path for 'formal intervention was determined and is presented here.

Jan 1, 1994

By M. K. Larson, R. G. Wade

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time- dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct- shear tests on mudstone overcored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that the risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

Jan 1, 2002

By M. G. Schulz

Mining of molybdenum at Questa, New Mexico has been accomplished by block cave methods since August, 1983. As caving progresses, a periodic geologic evaluation is made of the rock-types present in finger raises on the Grizzly Level of the mine. The production maturity of the cave can be monitored by relating this data to geologic cross-sections through the ore body. The draw point mapping program is a simple and effective tool that is used in making draw control decisions at Questa.

Jan 1, 1985

By R. Bhaskar

An airborne dust cloud is an ensemble of particles of varied size, density, shape and states of aggregation. An understanding and quantifying of the dispersion and deposition of the dust generated in mines is essential to the development of measures for reducing worker exposure to dust. In coal mining, the major portion of the dust is generated during the cutting of coal using either a shearer or a continuous miner. The major phenomenon affecting ambient concentration is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian and eddy diffusion, and inertial impaction. The three major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. The mechanisms determining particle deposition are size dependent.

Jan 1, 1990

By R. A. Metz, Ted H. Eyde, Dan T. Eyde

Industrial minerals deposits present sampling and grade control problems not normally encountered in metal mining operations. No longer are industrial minerals simply crude ground mineral products but are in fact high purity chemical raw materials. Operators of industrial minerals mines and processing plants now must meet increasingly stringent specifications established by the consumer of the final products. Meeting these stringent specifications requires not only sophisticated processing techniques but equally important careful sampling and grade or quality control at the mine. A well-trained geological staff can assure an adequate supply of uniformily high quality feed to the processing plant. In the final analysis this results in significantly higher operating profits.

Jan 1, 1992

By James E. Lawver

Response surface methodology is a well-known and powerful technique for determining optimum conditions in flotation systems. One disadvantage is the onerous task of the numerical calculations and curve platting. This paper describes a system in which the investigator simply selects the range of several flotation variables after which the design of the experiment, data analysis, generation of response surface equations, and response surface plats are automatically carried out using a digital computer and a computer-driven curve plotter. Several typical response surfaces of important variables in phosphate flotation are presented as examples. An overview of the flow charting of the system is provided in the addendum.

Jan 1, 1978

By C. J. Johnson, C. J. Bise

Coal extraction by continuous miners (CM) is currently the most common underground method in the US industry and accounts for slightly more than two-thirds of the nation's deep mining production (National Coal Association, 1987). Even if longwall mining should become more commonplace, it can proceed only after ventilation and access entries have been driven by CMs. Since an area of concern continues to be the effects of the dust generated on the health of mineworkers, this paper discusses the relationship between the elemental compositon of mining-generated airborne dust sampled from the immediate ventilation return of a CM and laboratory-generated dust derived from channel samples taken from the mines. There are several potential contributions of this type of study to the coal mining industry. First, after more fundamental knowledge of the causes of Coal Worker's Pneumoconiosis (CWP) is learned, the laboratory-generated respirable dust could be used to identify a potentially hazardous coal seam. Also, this study could possibly aid in understanding the fundamental causes of CWP by producing mining-simulated samples of coal dust that could be used in epidemiological studies. Further. assuming that there is no difference in the elemental composition of a drill-core sample and a channel sample from the same location, a mining company could predict anew mine's respirable dust elemental composition in the immediate ventilation return by using exploratory drill core samples of the roof, coal, and floor rock to prepare the laboratory dust. Ventilation engineers could then use engineering design and control measures during premine planning to reduce the incidence and severity of CWP by better ventilating the potentially hazardous coal seam. If this proper planning prevented any future changes to the ventilation equipment and mine design. much time and money could be saved. Scope of work To investigate the variability of the chemical characteris tics of respirable dust, airborne dust samples from eight underground coal mines located in the eastern and midwestern United States were collected with eight-stage Sierra Model 298 Marple cascade impactors, as well as 25 channel samples of mined material. Each channel sample was removed from the middle of the coal face before mining occurred. Sampling of the mining-generated dust was conducted by Lee (1986) by sampling the entire working sections, primarily for characterization purposes, to obtain information on the locational variability of dust characteristics. Research performed for this study used the elemental analyses of the mining-generated dusts he sampled in the immediate ventilation returns of CMs. The procedure that was used to produce the laboratory generated respirable dust was based on the Hardgrove grindability test since it reflects the pulverizing characteristics of coal. This test was chosen for several additional reasons. First, it is repeatable and reproducible. A consistent amount of input energy is used as well as a specified size range of feed material to be crushed (the channel samples). Second, it is thought to generate secondary dust in a way similar to that of the crushing and grinding of the coal and rock as they pass through the arc-shaped cutting path of the CM's cutter head. The potential effect on dust generation by this secondary grinding mechanism may be at least as much as that produced by primary fragmentation, which is dust produced by the cutting action of the bit against the coal or rock (Roepke. 1984). Finally, the Hardgrove grindability test is well known and is used in the coal industry to guide mineral processing engineers in estimating the capacity of mills used to grind coal. One hypothesis of dust researchers in the Generic Technology Center for Respirable Dust is that the elemental as well as the physical characteristics of coal mine dust will make a difference in the incidence and severity of CWP. Coal mine dust is generated not only from coal, but also from any rock partings contained within the seam or any roof or floor material mined with the coal. Thus, coal mine dust may not have the same elemental characteristics as the coal being mined. Given that hypothesis, mixtures proportional to each thick¬ness mined of roof, coal, and floor rock derived from the channel samples of the face areas from which the respirable dusts were generated by the CMs were used to produce the feed material that was pulverized in the Hardgrove machine.

Jan 1, 1990

By F. Freme

Coal production in the United States in 2009 de-creased to 972.8 Mt (1,072.8 million st), according to preliminary data from the U.S. Energy Information Administration (EIA). This is a decline of 8.5 percent, or 90 Mt (99.1 million st) below the 2008 record level of 1.06 Gt (1,171.8 million st) (Table 1). In 2009, U.S. coal consumption decreased in all sectors while total coal stocks increased for the year. Coal consumption in the electric power sector in 2009 was lower by 10 percent, while coking coal consumption decreased by 30.6 percent and the other industrial sector declined by 16.6 percent. The commercial and institutional sector (which prior to 2008 had been called ?residential and commercial?) is the smallest of all the coal-consuming sectors and it declined by 8.4 percent in 2009. (Note: all percentage change calculations are done at the short tons level.) U.S. coal exports fell from the 2008 levels, while coal imports decreased for a second year in a row. The decline in coal consumption during the year was the consequence of the domestic economic conditions combined with the weather in 2009, which resulted in lower demand for electricity. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers, including useful thermal output) in the U.S. decreased in 2009. Coal-based generation also decreased, resulting in a 94-Mt (104-million st) drop in coal consumed in the electric power sector. Coal use in the non-electricity sector decreased by 20.1 percent to a level of 57.9 Mt (63.9 million st). The international coal markets for most of 2009 were reflective of a worldwide economic slowdown. U.S. coal exports and imports both declined for the year. U.S. coal exports totaled 53.6 Mt (59.1 million st). This is a decrease of 20.3 Mt (22.4 million st) from the 2008 level.

Jun 1, 2010

By E. Westman

Geographic Information Systems (GIS) are becoming a more commonly used tool for resource estimation as they provide not only a database management platform, but also the graphical capabilities to visualize resource characteristics. Interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at several locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 1999

By E.C. Jong

Resumen ¦ Un sistema de comunicaciones “a través del suelo” (TTE) comercial y disponible fue evaluado en una mina de carbón subterránea en la zona Este del Estado de Kentucky. Este estudio de campo fue realizado como parte de una evaluación multisitio mayor de sistemas TTE disponibles. La mina detallada en este estudio se encontraba paralizada al momento de la evaluación, lo que proporcionó la representación más cercana a la realidad del medio ambiente en una mina luego de una operación de cierre. Para este estudio se probaron las comunicaciones superficie a subterráneo y subterráneo a superficie. El despliegue estándar del sistema TTE usando los procedimientos recomendados por el fabricante logró obtener comunicaciones claras y nítidas entre el socavón y la superficie. Otras disposiciones de las unidades arrojaron resultados mixtos. Existen planes para examinar más los fenómenos observados en esta mina.

Apr 1, 2016

By A. W. Khair

In 1985, an extensive longwall mining research project was initiated by the West Virginia University Research Center entitled "An Improved Longwall Mining Technique" with the purpose of providing operational guidelines for the mining industry to enable efficient operation of its existing and projected longwall installations. One task involved in this extensive research project was monitoring ground movements due to longwall mining and evaluating their impact on surface and subsurface structures. This paper presents an analysis of the effects of topography on quasi-static and dynamic ground movements and the severity of damage inflicted on surface structures. The site was chosen for the study with an attempt to obtain a representative account of the topography experienced in the Northern Appalachian region, and more importantly to contain a substantial number of varying topographical features i.e., mountains, hillsides, valleys, and flat bottom land. The study was made possible by typical subsidence monitoring technqiues, however subsidence monuments were surveyed on a frequent basis, intermittently during face advancement. Ground movements were investigated under both quasi-static and dynamic conditions. This provided insight into the propagation of subsidence and the dynamic affects it has upon surface structures.

Jan 1, 1987

By Joseph S. Malesky

The discovery and development of explosives mark one of the most important findings in the history of civilization. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. For these reasons explosives are rightfully referred to as the forerunner of progress. An explosive may be defined as a substance (usually a mixture) that, when flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents.

Jan 1, 1981